REPAIR MAINT AND REPLACEMENT TO LT DISTRIBUTION SYSTEM SUCH AS CABLE LT SWITCH GEARS PANELS AND OTHER ALLIED WORKS UNDER AGE E M I UNDER GE CENTRAL KHADKI

Amount

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth for laying of Cable/pipe and getting out in soft / loose soil complete all as specified and as directed by Engr-in-Charge

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth for laying of Cable/pipe and getting out in soft/disintegrated rock complete all as specified and as directed by Engr-in-Charge

Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm thick complete all as specified and as directed by Engr-in-Charge

Excavating in trenches n.exc 1.5m wide and exc 1.5m but n.exc 3m in depth for laying of Cable/pipe and getting out in Hard / dense soil complete all as specified and as directed by Engr-in-Charge

Removing of excavated soil n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed by Engr-in-Charge.

Removing of excavated soft / disintegrated rock n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed by Engr-in-Charge.

M&L PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate as in foundation for filling in, mass concrete for foundation of Pole, Transformer, Panel board, stay, post top lantern, repairs to road cutting, drain, path and for chain link fencing etc complete all as specified and as directed by Engr-in-Charge.

M&L PCC M-15 grade (Nominal Mix) using 20mm graded stone aggregate as in coping of new pole / reconstruction old damaged copings etc, including necessary form work complete all as specified and as directed by Engr-in-Charge.

M&L for crushed stone grid for cushioning to under ground cable in trenches/existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as specified and as directed by Engr-in-Charge. Note:- Measurement shall be taken after gentling punning.

Supply and laying un-reinforced precast concrete cable cover LV, Type I, flat, size 250mm x 150mm x 40mm for under ground cable complete all as specified and as directed by Engr-in-Charge.

Supply and lay double wall corrugated (DWC) high density polythene pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS 16205 & 14930 (Part-I and II) for protection of underground cable of following sizes with all fittings such as clamps, coupler etc. laid in trenches/roads/nallah or fixed along wall/ poles or laid under floor (including cutting floor/road and making to match with existing adjoining surface etc. for cable protection complete all as specified and as directed by Engr-in-Charge. Note:-Excavation and earth work shall be measured and paid separately under relevant item of this BOQ (Schedule ) Make :-Alcorr/Rex/Gemini or its equivalent make as approved by GE.

Dismantling / taking out carefully old/unserviceable UG cable any type any size from trenches/poles/ducts/LT panels after dismantling ends from OH conductors/MCCBs/joint boxes for relaying/refixing or carrying to store for Sch of Credit.

Material and labour for fixing or passing through pipe, laid in trenches or fixed to pole/wall or fixed to LT panel board, 1100 volts grade heavy duty XLPE UG cable with PVC insulated stranded aluminium conductor served with inner sheathing of PVC tape, armoured with galvanised steel wire or tape and overall PVC sheathed of following sizes with required aluminium cable lugs complete all as specified and as directed by Engr-in-Charge.

6 sqmm 2 core

10sqmm 2 core

16sqmm 2 core

10sqmm 4 core

16sqmm 4 core

25sqmm 3.5 core

35sqmm 3.5 core

50sqmm 3.5 core

70sqmm 3.5 core

95sqmm 3.5 core (MW LINE TO 512 WORK SHOP)

120sqmm 3.5 core (MES IB TO AWWA HOSTEL)

185sqmm 3.5 core

240sqmm 3.5 core

Dismantling/ taking out broken/worn out steel pole of 8.5 to 9.0 mtr long and keeping aside for refixing or carrying to store for credit

Supply and erect in true vertical position steel tubular swaged poles in replacement complete with MS base plate of 6mm of size 300mm X300mm finial taper plug, pole cap,bolts,nuts and washers screws, pole made out of ERW MS tubing as per IS-1161 and pole shall be as per IS-2713 Part II type 410 SP-31 (9.00 m Long) complete including one coat of red oxide zinc chrome primer and two coats of Aluminium paint for exposed surfaces and two coats of black bituminous paint for portion embedded in concrete complete all as specified and as directed Note: Excavation and earth work, PCC in foundation / plinth block/coping shall be measured and paid separately under relevant item of this BOQ

Dismantling and taking down old unserviceable cross arms, bracing, supports etc complete for reuse at site or carrying to store for sch of credit complete all as specified and as directed by Engr-in-Charge.

M&L cross arms bracings supports clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding bending cold or hot, drilling holes for bolts in any shape or size as indicated or directed and applying two coats of aluminium paint over one coat of red oxide primer l applying two coats of aluminium paint over one coat of red oxide primer complete all as specified and as directed by Engr-in-charge.

Dismantling and taking down old unserviceable ACSR conductor any size complete for reuse at site or carrying to store for Sch of Credit complete all as specified and as directed by Engr-in-Charge.

M&L for replacing old ACSR conductor incl jointing with existing conductor and straining on LT pole and proper fastening to pin/shackle insulators with aluminium binding wires and required jumpering connection complete all as specified and as directed by Engr-in-Charge.

Dismantling and taking down old/unserviceable insulator of any type any size from pole/stay for reuse at site or carrying to store for sch of credit complete all as specified and as directed by Engr-in-Charge.

M&L pin type, porcelain, vitreous, brown, including one galvanised mild steel spindle, two galvanised iron washer and one galvanised iron nut, 100mm height and 65 mm dia for 1100 volts grade complete all as specified and as directed by Engr-in-Charge.

M&L shackle type,porcelian vitreous white, brown or green insulator including galvanised mild steel straps , washers, insulators bolts ,washer and nuts of size 100 mm height and 115 mm dia for 1100 Volts grade complete all as specified and as directed by Engr-in-Charge.

M&L Loop type insulator, porcelain vitreous brown of size 65x90mm and clearance hole 16mm complete all as specified and as directed by Engr-in-Charge.

M&L for Stay assy using 16mm dia galvanised rod complete all as shown in electrical plate No 1 of SSR Part I including dismantling unserviceable one complete all as specified and as directed by Engr-in-Charge. Note:-Clamps, loop insulator, earth work, PCC etc shall be measured and paid separately under relevant item this BOQ.

M&L for stay wire using galvanised steel strand of 7/3.15mm complete with necessary binding incl dismantling taking down unserviceable one complete all as specified and as directed by Engr-in-Charge.

M&L for cradle hexagonal /rectangular fabricated with galvanised steel wire not less than 4mm dia on pole including dismantling taking out unserviceable cradle guard complete all as specified and as directed by Engr-in-Charge.

S&F earth continuity wire using GI wire not less than 4mm dia on pole incl dismantling taking out unsv GI wire complete all as specified and as directed by Engr-in-Charge.

M & L for Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with earthing lead of 4mm dia galvanised iron or steel wire all as shown in Plate No. 2 to the earthing test point all as specified and indicated including testing on complete all as specified and as directed by Engr-in-Charge.

M&L for Earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground earth pit not less than 2.25mtr deep below normal ground level with top edge of the plate not less than 1.5 mtr below ground level connected to galvanized iron strip of size 32x6 mm as earthing lead by mean of nut/bolt and washer of galvanized iron or steel drawn through 40 mm dia light grade GI pipe as shown in electrical plate no 3 of SSR part I of 2009 including necessary excavation and earth work GI pipe 20 mm dia medium grade for watering PCC chamber with PCC cover in cement concrete M-15 grade (Nominal Mix) using 20 mm graded stone aggregate, funnel, wire mesh, charcoal dust, salt etc connected to panel board/ Gen set as indicated including testing complete all as specified and as directed. Note:- Earth protection pipe & earthing strip upto and including 7.5 m length is deemed included in unit rate quoted by the contractor.

M&L for restraining of overhead ACSR conductor of any size of 4 wire 35-45 met span on pole after disconnecting all jumpering connection & binding of insulators and redoing all jumpering connection and insulator binding with aluminium conductor providing required T&P complete all as specified and as directed by Engr-in-Charge.

M&L for restraining of ACSR conductor of any size of 2 wire 35-45 met span on pole after disconnecting all jumpering connection & binding of insulators and redoing all jumpering connection and insulator binding with aluminium conductor providing required T&P complete all as specified and as directed by Engr-in-Charge.

M&L for restraining of GI Cradle guard hexagonal/rectangular of any size 35-45 met span on pole after disconnecting all binding on cross arms and redoing all bindings providing required T&P complete all as specified and as directed by Engr-in-Charge.

M&L for restraining of GI earth wire of any size 35-45 met span on pole after disconnecting all binding on cross arms and redoing all bindings providing required T&P complete all as specified and as directed by Engr-in-Charge.

Cutting/Trimming of tree branches around 3m distance from conductors of HT over head line of span up to 50 meters including removing of creepers etc fron poles Note:- Measurement shall be taken once for entire period of contract

Cutting/Trimming of tree branches around 3m distance from conductors of LT over head line of span up to 40 meters including removing of creepers/vegetation etc fron poles Note:- Measurement shall be taken once for entair period of contract

M&L Heat shrink end joint indoor/outdoor LT 1100 volts grade 10-16 sqmm, 4 core, Make:-Raychem, Cat No-EPKT0003 or equivalent make given under list of makes

M&L Heat shrink end joint indoor/outdoor LT 1100 volts grade 25-50 sqmm, 3.5 core, Make:-Raychem, Cat No-EPKT0019or equivalent make given under list of makes

M&L Heat shrink end joint indoor/outdoor LT 1100 volts grade 70-150 sqmm, 3.5core, Make:-Raychem, Cat No-EPKT0035 or equivalent make given under list of makes

M&LHeat shrink end joint indoor/outdoor LT 1100 volts grade 185-300 sqmm, 3.5 core, Make:-Raychem, Cat No-EPKT0051 or equivalent make given under list of makes

M&L Heat shrink straight through joint out door type LT 1100 volts grade 10-16 sqmm, 4 core, Make:--Raychem, Cat No-EPKJ0123 or equivalent make given under list of makes

M&L Heat shrink straight through joint outdoor type LT 1100 volts grade 25-50 sqmm, 3.5 core, Make:- Raychem, Cat No-EPKJ0130or equivalent make given under list of makes

M&L Heat shrink straight through joint outdoor type LT 1100 volts grade 70-150 sqmm, 3.5 core, Make:-Raychem, Cat No-EPKJ0137 or equivalent make given under list of makes

M&L Heat shrink straight through joint outdoor type LT 1100 volts grade 185-300 sqmm, 3.5 core, Make:--Raychem, Cat No-EPKJ0144 or equivalent make given under list of makes

M&L for applying two coats of aluminium paint including preparation of steel surface of steel pole any type up to 7.5 mtr height above ground level including cross arms,clamps,stay clamps etc complete all as specified and directed by Engr-In-Charge

M&L for Numbering of HT/LT poles serially with letter/number size width and height up to 40 mm in site with white paint on black back ground

M&L GI tubing light grade 40mm bore, on pole /wall with necessary clamps,nuts,bolts and washers/under road cross ISI marked, for cable protection including taking out old pipes complete all as specified and as directed by Engr-in-Charge.

M&L GI tubing light grade 50mm bore on pole /wall with necessary clamps,nuts,bolts and washers/under road cross ISI marked, for cable protection, ISI marked, for cable protection including taking out old pipes complete all as specified and as directed by Engr-in-Charge.

M&L GI tubing light grade 80mm bore, on pole /wall with necessary clamps,nuts,bolts and washers/under road cross ISI marked, for cable protection ISI marked, for cable protection including taking out old pipes complete all as specified and as directed by Engr-in-Charge.

M&L GI tubing light grade 100mm bore,on pole /wall with necessary clamps,nuts,bolts and washers/under road cross ISI marked, for cable protection ISI marked, for cable protection including taking out old pipes complete all as specified and as directed by Engr-in-Charge.

M&L for jumper connections of length up to 1.50 met with existing size and gauge of ACSR, binding with existing conductors for LT OH lines complete all as specified and as directed by Engr-in-Charge.

M & L for Danger notice plate of 1.6mm thick MS sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with MS clamps, bolts and nuts of approved size, for LT 1100 volts, 25 x 20 cm size including taking out defective danger boards complete all as specified and as directed by Engr-in-Charge.

M & L for Danger notice plate of 1.6mm thick MS sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with MS clamps, bolts and nuts of approved size, for HT 11000 volts, 25 x 20 cm size including taking out old danger boards complete all as specified and as directed by Engr-in-Charge.

Supply and erect Cast Iron HT/LT cable route indicator round shaped 120 mm dia 8 mm thick duly embossed with MES HT/LT Cable fixed on flat iron 25X3 mm thick 300 mm long and including grouted in PCC M-15 grade (Nominal Mix) using 20mm graded stone aggregate of requisite size all as directed

M & L for rigid PVC line spacer, U-shaped, spiral type, suitable for 2 wire, made from high grade PVC material, distance between phase to phase 300mm, suitable for use with 1100 volts grade. Make- Shree Balaji Power Plast/Goyal Power Plast

M & L for rigid PVC line spacer, U-shaped, spriral type, suitable for 4 wire, made from high grade PVC material, distance between phase to phase 300mm, suitable for use with 1100 volts grade. Make- Shree Balaji Power Plast/Goyal Power Plast

M & L for aluminium cable lugs of size 50 sqmm flat head in Aluminium conductor/cable fixing with Nuts, bolts & washers to junction point as directed, (Note-To be measured only, fixed at places other than with heat shrink joints)

M & L for aluminium cable lugs suitable for XLPE cable size 70 sqmm flat head in Aluminium conductor/cable fixing with Nuts, bolts & washers to junction point as directed, (Note-To be measured only, fixed at places other than with heat shrink joints).

M & L for aluminium cable lugs suitable for XLPE cable size 95 sqmm flat head in Aluminium conductor/cable fixing with Nuts, bolts & washers to junction point as directed, (Note-To be measured only, fixed at places other than with heat shrink joints).

M & L for aluminium cable lugs suitable for XLPE cable size 120 sqmm flat head in Aluminium conductor/cable fixing with Nuts, bolts & washers to junction point as directed, (Note-To be measured only, fixed at places other than with heat shrink joints).

M & L for aluminium cable lugs suitable for XLPE cable size 150 sqmm flat head in Aluminium conductor/cable fixing with Nuts, bolts & washers to junction point as directed, (Note-To be measured only, fixed at places other than with heat shrink joints).

M & L for aluminium cable lugs suitable for XLPE cable size 240 sqmm flat head in Aluminium conductor/cable fixing with Nuts, bolts & washers to junction point as directed, (Note-To be measured only, fixed at places other than with heat shrink joints).

M & L for aluminium cable lugs suitable for XLPE cable size 300 sqmm flat head in Aluminium conductor/cable fixing with Nuts, bolts & washers to junction point as directed, (Note-To be measured only, fixed at places other than with heat shrink joints).

M & L for MCCB, 4 pole, 36 KA breaking capacity, Ics = 100% Icu as per IEC 60947-2, with Thermal magnetic release, 400 amps, complete all as specified and directed by Engr-in-Charge

S & F in repairs MCCB, 4 pole, 36 KA breaking capacity, Ics = 100% Icu as per IEC 60947-2, with Thermal magnetic release, 350 amps complete all as specified and as directed by Engr-in-Charge,

S & F in repairs MCCB, 4 pole, 36 KA breaking capacity, Ics = 100% Icu as per IEC 60947-2, with Thermal magnetic release, 200 amps, complete all as specified and as directed by Engr-in-Charge

S & F in repairs MCCB, 4 pole, 36 KA breaking capacity, Ics = 100% Icu as per IEC 60947-2, with Thermal magnetic release, 250 amps,complete all as specified and as directed by Engr-in-Charge,

S & F in repairs MCCB, 4 pole, 36 KA breaking capacity, Ics = 100% Icu as per IEC 60947-2, with Thermal magnetic release, 160 amps,complete all as specified and as directed by Engr-in-Charge

S & F in repairs MCCB, 3 pole, 35 KA breaking capacity, Ics = 100% Icu as per IEC 60947-2, with Thermal magnetic release, 200 amps, complete all as specified and as directed by Engr-in-Charge

S & F in repairs MCCB, 3 pole, 35 KA breaking capacity, Ics = 100% Icu as per IEC 60947-2, with Thermal magnetic release, 350 amps, complete all as specified and as directed by Engr-in-Charge

S & F in repairs MCCB, 3 pole, 35 KA breaking capacity, Ics = 100% Icu as per IEC 60947-2, with Thermal magnetic release, 160 amps, complete all as specified and as directed by Engr-in-Charge

S & F in repairs MCCB, 3 pole, 16 KA breaking capacity, Ics = 100% Icu as per IEC 60947-2, with Thermal magnetic release, 125 amps, complete all as specified and as directed by Engr-in-Charge,

S & F in repairs MCCB, 3 pole, 16 KA breaking capacity, Ics = 100% Icu as per IEC 60947-2, with Thermal magnetic release, 100 amps, complete all as specified and as directed by Engr-in-Charge

S & F in repairs MCCB, 3 pole, 16 KA breaking capacity, Ics = 100% Icu as per IEC 60947-2, with Thermal magnetic release, 63 amps, complete all as specified and as directed by Engr-in-Charge

S & F in repairs MCCB, 3 pole, 16 KA breaking capacity, Ics = 100% Icu as per IEC 60947-2, with Thermal magnetic release, 40 amps complete all as specified and as directed by Engr-in-Charge

M & L for replacing 1100 volts grade heavy duty flat twin core cable PVC insulated with stranded aluminium conductor of following size and overall PVC sheathed in service connections from OH conductor to building including dismantling taking down unserviceable one complete all as specified and as directed by Engr-in-Charge

Labour for disconnecting LT cable of any size from structure/pole/transformer for finding fault and M&L for defect rectification LT cable laid in trenches or any location by locating fault with the help of electronic fault machine comprising of surge generator pulse, ECHO fault locator with high frequency distance calculator etc. The entire repair work to be completed with in 6 hours of instruction from Engr-in-charge as specified. Note:- (i) Complaint will be notified to contractor on mobile phone at any time between 0800 to 2200 Hrs and same shall be rectified with in 6 hours after notification, failing to which Rs 500/- per day complaint will be recovered. fault locating with electronic fault locator, excavation and earth work, disconnecting and reconnecting both end of cable, relaying of sand and protective cable covers are deemed to be included in the quoted rate all as specified and directed by Engr-in-charge. (ii)Jointing kit shall be measured separately in appropriate item in this schedule

M&L for Replacing of LT panel modular out door type fabricated, weather and dust proof indoor type 3.15 mm thick CRCA sheet for outer body double door and 2.00 mm thick CRCA sheet for inner partition walls ,independent cabinet with cabinet doors for MCCB's ,Bus bars , cable trays, metering equipment vertical type, floor mounted, minimum IP-54 protection, suitable grouted to PCC foundation work with angle iron base frame 50x50x6mm complete with internal wiring, epoxy powder coated and connection of cable ends with suitable size of cable lugs and also provided locking arrangement with the following accessories. And CPRI approved all as specified and directed ( DRG shall be got approved from the GE before the order is placed ) Make:- BCH of any CPRI approved from PS. and Make of MCCBs : BCH/L&T/Legrandor equivalent make given under list of make (For CAFD Unit Line)

M&L for Replacing of LT panel modular out door type fabricated, weather and dust proof out door type 3.5 mm thick CRCA sheet for outer body double door and 2.00 mm thick CRCA sheet for inner partition walls ,independent cabinet with cabinet doors for MCCB's ,Bus bars , cable trays, metering equipment vertical type, floor mounted, minimum IP-54 protection, suitable grouted to PCC foundation work with angle iron base frame 50x50x6mm complete with internal wiring, epoxy powder coated and connection of cable ends with suitable size of cable lugs and also provided locking arrangement with the following accessories. And CPRI approved all as specified and directed ( DRG to be got approved from the GE before the order is placed ) Make:- BCH of any CPRI approved from PS. Make of MCCBs : BCH/L&T/Legrand or equivalent make given under list of make (for Stn HQ Exchange)

Repair and Replacement old unserviceable automatic power factor correction (APFC) panel out door type factory made of capacity 100 KVAR ready to use design confirming to relevant IS rated for short circuit rating of 100 KA front openable and lockable by keys having lower and air vent, gasket and totally vermin proof and suitable for 415/440 Volts, 3 phase 50 HZ AC and housed in elegant enclosure fabricated from minimum 3.15mm thick CRCA sheet, anty corrosive coated to achieve power factor from 0.9 t0 0.99 and finally powder coated in texture seimens gray RAL 7032 & as a directed by Engineer -in- charge comprising of and including following suitable size and length of copper cable from main panel to APFC panel for connections as approved complete all as specified and directed (a) 100 A capacity for phase and 63 A neutral aluminium bush bar duly insulated with colour coated heat shrincablesleeves and mounted on suitable DMC/epoxy insulator. (b) MCCB 160 Amp 25 KA TP TM based O/C and S/C Rel -01 Nos incoming (c) 6A FPMCB 10 KA -03 Nos (d ) 10 Amp TP MCB 10 KA -02 Nos (e) 20 A TP MCB 10 KA -01 Nos (f) 25 Amp TP MCB 10 KA -03 Nos (g) power contactor 9.7 KVAR TP cap duty,230 Volt AC - 03 Nos (h)power contractor 12.5 KVAR TP cap duly 230 VAC -03 Nos (j) Auxiliary contact -4 NC-01 Nos 230 VAC (k) Add on Auxillary contract-4NC -01 Nos (l) add on auxillary contact- 1No +1NC -01 (m) 6Step APFC Relay MP based 230 VAC ,-CT -01 (n) indicating lamps R,Y,B -01 Nos Each (o) A/M Sel switch,1P,2W -01Nos (p) A set of heavy duty capacitor type MPPH box type 440Volts. with output step of 100 KVAR capacity bank in steps of with 6 steps (,1x5KVAR + 1x10KVAR + 1x15KVAR +1X20KVAR +1X25 KVAR +1x25KVAR) in any configuration to accommodate all possible set ups (q) Rocker switch illuminated type 230 VAC -08 Nos (r) MCB busbar connector R,y,B -06 Nos.

S&F in replacement thermoplastic cable junction box for street lights of size 205 x 255 x 112mm including bus bar/terminal for cable connection with IP-66 protection complete all as specified and as directed by Engr-in-Charge Make : Hensel Cat No.DK 2525 G or equivalent make given under list of makes

Dismantling fencing, wire mesh any type complete all as specified and directed by Engr in Charge

Supply only 3mm dia Hot Dipped Galvanized Chain Link Fencing with Zinc Coating, including line wires, any type of standards, rails, straining bolts, etc. including provision of binding wire incl dismantling taking down unserviceable one (2.8 Kg per sqm with 2"x2" mess of 3 mm wire) complete all as specified and as directed by Engr-in-Charge

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

S & F in repairs Mild steel for posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0

M&L for replacing old unserviceable TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns hooking ends or as in horizontal bar for fixing in fencing and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete for support of chain link fencing incl dismantling taking down unserviceable one complete all as specified and as directed by Engr-in-Charge

19. M & L for filling and spreading stone aggregate using 40 mm grade trap stone aggregate around 4 pole , 2 pole structure and 11KV Receiving power stn.etc.complete all as specified and as directed by Engr-in-Charge

S & F glow sign boards of size 12' x 3'x 1' made out of acrylic sheet of 3 mm thick with letters as directed at various Sub Station holding on 3.5 mtr height stainless steel pipe 32mm, height 3 Mtr, providing lighting/illumination with four tube light set and wiring upto connected point complete as per sample complete all as specified and as directed by Engr-in-Charge NOTE :- Sample of glow sign board shall be got approved by Engr-in-charge/GE before placing the order.

JP ENTERPRISES (BID ID -3252413)

Om Construction (BID ID -3254078)

ONKAR ELECTRIC AND GENERAL STORE (BID ID -3254256)

Priyanka Power line (BID ID -3254091)

Star Electrical (BID ID -3253985)

Mahindra Electric Stores (BID ID -3254183)

SBS Enterprises (BID ID -3253663)

Bidder Name

JP ENTERPRISES

MANGAL ELECTRICAL STORES

Star Electrical

SBS Enterprises

Priyanka Power line

Mahindra Electric Stores

Om Construction

ONKAR ELECTRIC AND GENERAL STORE