GE(S) BTD 22 OF 2024-25 CERTAIN BR REPAIR INCLUDING ATTENDING DAY TO DAY COMPLAINTS REPAIR REPLACEMENT OF JOINERY TANK CLEANING AND CERTAIN OTHER MISC WORK TO VARIOUS BLDGS OF RANJIT ENCLAVE UNDER AGE BR I UNDER GE (SOUTH) BATHINDA AT BATHINDA MILIT

Amount

Comprehensive maintenance for Carpentry work by attending day to day complaints of joinery related such as replacement of Builders hardware of doors, windows & cupboard and other Carpentry nature works like easing/re-securing & adjusting, without taking down shutter of door, windows and cupboards. Tightening of screws for tower bolt/Aldrop bolt/ stoppers, handle hinges in respect to easing of door / windows/cupboards (Steel Wooden/Aluminium) of any description and size by cleaning, adjusting in position and making the same functional incl fittings (if reqd) with and incl greasing, oiling, screws/nales for fixing the fittings complete all as specified and directed.

Comprehensive maintenance to masonry work by attending day to day complaints of masonry related works such as plastering of wall/ceiling/chajja/making of jambs, soffit, cills etc of size not exceeding 0.25 sqm or on patch work including finishing with distemper/white wash/cement based paint/exterior emulsion paint including two coats of putty as required at site to match with existing surface.

Comprehensive maintenance to plumbing work by attending day to day complaints of plumbing nature like leaking bib taps, stop cock of any pattern or of any type including minor repairs to flush cistern, repair to PE-AL-PE composite pressure pipe/GI pipe leakages, removing air blockages if any and refixing old serviceable bib cocks, stop cocks any pattern after minor repairs such as replacement of washers, jumpers and spindle etc complete all as specified and directed. (any items like thread , Teflon tape, rubber washer, syphon kit, jumpers, brass spindles, caps etc shall be deemed to be included in the quoted rates). Note for item No 1 to 3. The scope of work is of day to day maintenance nature/ requirement of works. Contractor shall attend the office of AGE B/R-I on daily basis and receive/ collect the complaints/ requirements of works and shall rectify the repair/maintenance works within time given below :- (a) Minor plumbing complaints - 48 hours (b) Minor Joinery complaints - 48 hours (c) Minor masonry complaints - 48 hours (d) Major Plumbing - 5 days (e) Major Joinery - 15 Days. If contractor fails to rectify the complaints with materials/ items to be replaced if required a penalty @ 50% of quoted rate by the contractors of that particular item shall be recovered from his payment. The responsibility of getting the complaints attended & rectified shall lies with the contractor even if he fails to complete the complaints within 48 hours. In the delayed case of a rectification of complaints even after 48 hours, he shall rectify the same within one week. (Note :- The complaint received from complaint cell shall have to be attended on same day).

Taking down chowkats or frame with shutter (without taking off shutters from the frames) n. exc 1.50 sqm each all as specified

Taking down chowkats or frame with shutter (without taking off shutters from the frames) exc 1.50 sqm but n. exc 4.00 Sqm each all as specified

Taking down shutters of any description exceeding 1.00 sqm but not exceeding 2.00 sqm each and removed from site all as specified

S & F pressed steel frames for doors with one or more rebates including hinges, lock strike plate, fixing lugs, etc., size of frame 125 x 60mm, complete all as specified (thickness of steel sheet shall be 1.25mm)

S & F pressed steel frames for doors with one or more rebates including hinges, lock strike plate, fixing lugs, etc., size of frame 105 x 60mm, complete all as specified (thickness of steel sheet shall be 1.25mm)

M & L for PCC 1:3:6 type C1 (using 20mm graded crushed stone aggregates) as in filling back of pressed steel door frames/chowkats and for fixing hold fasts, etc., complete all as specified

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length including necessary finishing of wall for fixing of frame complete as per direction of Engineer-in-Charge.

Ditto all as per item above but of double shutter frame size 65 x 125 mm

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges (04 Nos Minimum), Stainless steel fancy type door handle, 2 x tower bolt (200mm Long) and 1 x sliding bolt (300mm long) with nut & bolts as approved by GE with necessary fixing arrangement of required size all as per specified and as directed by Engineer In- Charge.

S&F 2nd class HW 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut & mitered beads for securing glass, gauze, etc.; sizes of members of shutters as specified in SSR Part I Section 8, Clause 8.24 (a) all as specified

S&F 2nd class HW 35mm thick plain framed, factory made panelled shutter (two panel) with lock rail and panel of 9mm thick B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part I) kiln seasoned and chemically pressure treated complete all as specified and directed.

M & L 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified

S & F mild steel framed work such as grills, guard bars, gate, gratings, door frame etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe290,Gde-E-165 complete all as specified and as directed

S & F for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube fixed in opening complete as per specifications & drawing

S & F for 30 mm thick factory made solid panel PVC door shutter confirming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 gauge thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming styles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings

S&F for steel windows/ventilators with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with or without glazing bars, dovetailed or welded, including steel window/ventilators complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or fixed with beads complete all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or fixed with beads complete all as specified and directed.

M&L in repairs 2nd HW plain fillets, square, rectangular or triangular in section, wrought, secured with nails/brads or secured with screws, cross sectional area exc 6 sqcm and n. exc 13 sqcm, complete all as specified

S & F in stainless steel Butt Hinges, 100 mm size, medium weight, fixed with screws/welding to wooded/steel frames or chowkats, complete all as specified

S&F for MS sliding door bolt 250 mm long stove enamelled black with bright bolt etc.

S&F in repair MS tower bolt 150 mm long stove enamelled black with bright bolt.

S&F in repair MS pressed handles, oval type stove enamelled black 150 mm long.

S&F repairs aluminium, anodised, barrel tower bolts of extruded section and fixed, 150mm length, complete all as specified

S&F repairs 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified

S&F repairs Aluminium anodised handles cast type 150 mm long complete all as specified

S & F floor door stopper 140mm size of aluminium alloy body and tongue, anodised, with hard drawn steel spring all as specified

S & F door bottom sealing strip guard gap filler stopper sealer sound and dust proof weather stripping noise stopper protector strong self adhesive complete all as specified.

S & F in repairs 300mm mild steel ordinary rat tail rod springs (helical spring) , including roller & roller plate, fixed with screws/welding to steel frames/chowkats, complete all as specified

S & F in repairs 25mm dia fancy type harrison rails, stainless steel, chromium plated with fixing brackets, stops, rollers etc. curtain rod with brackets and knobs at both ends as per site requirement complete all as specified

S & F in repair 40 mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished and fixed complete all as specified and directed.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket. NOTE:- Glass panes & wire mesh shall be measured and paid for separately under respective item of BoQ.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. NOTE:- Glass panes shall be measured and paid for separately under respective item of BoQ.

Dismantling boarding any description fixed in any position with rails incl fillets

S&F 18/19mm thick pre-laminated particle board, interior grade, fixed with screws to timber frame work and steel frame work as in kitchen cupboards, drawers, shutters, shelves etc including teak wood lipping, 6mm thick on edges fixed with nails etc, complete all as specified

S&F ( to be fixed with screws & welding as required) continuous (piano) hinges, mild steel, bright finish or electro galvanised, width of flap (when open) 30mm all as specified

S&F for Al hasp and staple 100 mm size.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame incl punching or drilling out old glazing pins/springs clips and fixing new ones all as specified

S & F for 3 mm thick, sheet glass ordinary quality and glazing with oil putty or fixed in any type of frame (such as aluminium wooden mild steel) in square n. exc 0.5 sqm in each pane all as specified

S & F for 3 mm thick, figured glass, pin head type and glazing with oil putty or fixed in any type of frame (such as aluminium wooden mild steel) in square n. exc 0.5 sqm in each pane all as specified

M&L for running welding in repairs n. exc 6mm thick metal and n. exc 2.50 cm in length complete all as specified

S & F in repairs brass chromium plated tubular towel rail, 20mm dia, D type 60cm long between flanges all as specified

M&L for preparation of new steel and iron surfaces of any description exc 10 CM width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified

M&L for preparation of new or previously untreated wood and wood based surfaces of any description exc 10 CM width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified

M & L Non-skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bedding layer in CM 1:6 and including dismantling old plastered/terrazzo finishes/old tiles etc, clean the surface free from dust by washing etc ; and removed the waste material/debries out side of MD land complete all as specified and directed.

M & L Non-skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, on vertical surfaces as in skirting etc. set and jointed in neat cement slurry/paste and pointed in white or coloured cement to match over and including 10mm thick plaster in CM 1:4 including dismantling old plastered/terrazzo finishes/old tiles etc, clean the surface free from dust by washing etc ; and removed the waste material/debries out side of MD land complete all as specified and directed.

M&L non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed in CM 1:6 including dismantling old plastered/terrazzo finishes/old tiles etc, clean the surface free from dust by washing etc ; and removed the waste material/debries out side of MD land complete all as specified and directed.

M&L non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed in CM 1:4 and including dismantling down old plastered/terrazzo finishes/old tiles etc; and removed the waste material/debries out side of MD land complete all as specified and directed.

M & L glazed ceramic coloured tiles 7mm thick 350mmx 250mm/450mmx300 mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade etc complete all as specified including 10mm thick plaster in CM 1:4 i including dismantling old plastered/terrazzo finishes/old tiles etc, clean the surface free from dust by washing etc ; and removed the waste material/debries out side of MD land complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons & shelves laid bedded and pointed in any mortar all as specified.

M&L for machine cut cudappah stone slab 20-25mm thick (table rubbed and polished) as in cooking platforms and like in cement mortar (1:4) in pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade and provn of hole for gas pipe complete all as specified and directed.

M&L for marble work (any shade other than white) 18 to 20mm thick (table rubbed and polished) as in cooking platforms and like in cement mortar (1:4) in pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade all as specified (Note : Rates deemed to include for provision hole through marble & RCC slab for LPG gas pipe and rounding and polishing of edges of marble slab)

Material and labour for machine cut kota stone slab flooring 20-25mm thick over 20mm thick cement screed base in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L for Kota stone slab 20 to 25 mm thick in riser of steps, skirting, dado and pillar set and jointed in 20 mm CM (1:6) with neat cement slurry and pointed in white cement paste pigmented to the match the shade of slab laid over rendering in cement mortar including rubbing and polishing complete all as specified and directed .

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars etc., complete all as specified and directed.

M&L brick work in cement mortar 1:6 with sub class `B' old size bricks straight or curved on plan exceeding 6.0m mean radius built complete all as specified and directed.

M&L half brick work in cement mortar (1:4) with sub class 'B' bricks, straight or curved on plan to any radius etc; complete all as specified and directed.

Demolition of cement concrete (unreinforced) not exceeding 15 cm thickness (below or above ground level)incl rubbish off the premises complete all as specified and directed.

M & L 75mm thick, cement concrete 1:3:6, type C2 (using 40mm graded crushed stone aggregate) as in floors, plinth protection, paths, etc and finishing top surfaces even and smooth (without using extra cement) complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block (with grey cement and pigment) any shape and size of any colour/pattern as approved confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade over and include 25mm thick sand bed/cushioning complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block (with grey cement and pigment) any shape and size of any colour/pattern as approved confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade over and including 25mm thick sand bed/cushioning complete all as specified and directed.

Taking down of old interlocking tiles of any description and refixing the same over and including 25mm thick sand bed/cushioning complete all as specified and directed.

M&L for Chequred cement concrete tiles 20cm x 20cm x 25mm thick, with grey cement and no pigment set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed in CM 1:6 complete all as specified and directed.

M & L Cement Concrete type B1 , 1:2:4 mix (20mm graded crushed stone aggregate ) as in bedding , benching of manholes , copings, roof kerbs and surface channel etc. complete all as specified

M&L PCC 1:5:10 type E-2 using 40mm graded crushed/stone agg for foundations, filling & mass concrete, sub-base & sub-floors, filling of sunken floors etc. complete all as specified and directed.

Water proofing treatment to sunken slab and adjoining vertical surfaces as specified under:- (a) M&L rendering 10 mm thick in cement plaster (1:3) using coarse sand mixed with integral water proofing compound as per manufacturer's instruction trowel even and smooth with steel trowel on sunken surfaces (Note : WPC shall be measured and paid separately) (b) Applying first coat of chemical pidifin 2K(Dr Fixit) on cleared RCC surfaces @ 0.86 Kg/Sqm (Minimum) as recommended by manufacturer. (c) Provide a layer glass fibre mesh of size 2.25mm x2.25mm (45 GSM) over first coat of chemical Pidifin 2K as per manufacturers recommendation. (d) Applying second coat of chemical Pidifin 2K (Dr Fixit) @ 0.86 Kg/Sqm (minimum) layer glass fibre mesh of size 2.25mm x 2.25mm (45 GSM) as recommended by manufacturers.

Supply only Integral water proofing compound complete all as specified and directed. Make Dr. Fixit or any other equivalent make from list of make attached in tender documents as approved by GE.

Taking down cement or cement lime plaster of any description from brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed .

Material and labour for 15mm thick rendering in CM (1:4) on fair faces of brick work or concrete surfaces and finishing even & smooth but without using extra cement complete all as specified and directed.

Material and labour for 15mm thick rendering in CM (1:6) on other than fair faces of brick work or concrete surfaces and finishing even & fair but without using extra cement complete all as specified and directed.

Material and labour for rendering 5 mm thick in cement mortar in (1:3) on ceiling and finishing the surface even & fair without using extra cement complete all as specified and directed.

M&L for applying three coats of white wash on newly plastered surfaces on ceiling complete all as specified and directed.

M & L for preparation of old surfaces of ceiling and applying one coat of white wash complete all as specified and as directed.

M&L for preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of approved tint, quality, colour on these surfaces, complete all as specified and directed.

Complete removal of existing treatment on old Internal wall surfaces of any description, preparation of surface by Mechanised sander having suction vacuum Bag using Smart periodical methodology, complete all as specified and applying the following :- (a) M&L for wall care putty in two layers on wall surface and smoothening the surface with sand papers / Mechanised sanding etc preparatory to paint as directed complete all as specified (b) M&L for two coat of acrylic emulsion distemper of approved tint over a coat of primer on old prepared surface by using Airless spray/Roller complete all as specified. Note:- Contractor may use manual scraping tools for complete removal and surface preparation with prior approval of Engr-in-Charge in case of using of Mechanical equipment are not possible.

Preparation of New plastered Internal wall surface complete all as specified complete all as specified and applying the following:- (a) M&L wall care putty in two coats on wall surface and smoothening the surface with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified. (b) M&L two coat of acrylic emulsion distemper over a coat of wall care putty/chalk whitening priming by using Airless spray/Roller complete all as specified. Note:- Contractor may use manual scraping tools for complete removal and surface preparation with prior approval of Engr-in-Charge in case of using of Mechanical equipment are not possible.

M&L for applying two coats of cement base paint over a coat of primer on newly plastered wall and ceiling surfaces including cornices & pillasters etc including preparation of new surface all as specified

M&L for complete removal of existing treatment of any description on old wall surfaces of any description, preparation of surfaces by mechanized sander having suction vacuum bag using smart periodical methodology complete all as specified and applying two coats of cement base paint over a coat of primer on old wall and ceiling surfaces including cornices & pillasters etc including preparation of new surface all as specified

S & F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of size 20mm bore ( weight 210 gms Minimum) complete all as specified

S & F in repairs, brass chromium plated shower rose 150mm square, with swivel joints & and arms, and fixing to pipe & union all as specified

S & F in repairs soap dish chromium plated, fancy type, fixed to plugs with brass screws complete all as specified and directed.

S&F shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed.

M&L Mild Steel framed work of Gde Fe-410-0 or Fe-310-0 as in doors chowkats (single or double) of angles or other section with gusset plates, rails, braces, bands straps, hold fast grill, sink brackets, cooler stand etc, complete and including necessary welding for fixing flat iron for fixing hooks and hinges complete all as specified and directed.

S & F in repairs CP grating (with or without waste hole), 125mm size, fixed on floor/nahani gully trap traps etc complete all as specified and directed.

S&F in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S & F in repair PVC connection 15 mm size with PTMT nuts of length 450 mm of approved quality

S & F in repair PVC valve less, symphonic action type flushing cistern, low level, with inlet ball valve, float and handle including brackets, PVC bend long type and connection to flush pipe of any size and pattern complete all as specified

M&L 2mm thick, fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screws and washer in roof & wall etc; including dismantling of any description, complete all as specified

S & F in repair vitreous china wash basin, white, flat back, size 550 x 400mm excluding taps, wastes but including brackets complete all as specified

S & F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x460mm bowl size 410mm x330mm x160mm complete all as specified.

S&F in repairs stainless steel plate racks of size 900mmx600mmx250mm and thickness of SS strip 1mm, fixed on wall etc complete all as specified & directed by Engr-in-Charge.

S & F in repairs 15mm bore, fancy type, chromium plated, angle valve, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe all as specified.

S & F in repairs 15mm bore pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe all as specified

S & F in repairs 15mm bore fancy type chromium plated brass bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

S & F in repairs 15mm bore fancy type chromium plated stop valve cast copper alloy, with long shank & cup (concealed type) with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

S & F GI tubing medium grade with all fittings and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm including necessary chases cutting to walls and ceiling including taking up or down complete all as specified.

S & F GI tubing medium grade with all fittings and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm including necessary chases cutting to walls and ceiling including taking up or down complete all as specified.

S & F in repairs 110 mm bore of pipe PVC (SWR) pipes single socket in any length with rubber ring joint fixed to walls with MS clamps etc all as specified

S & F 110 mm bore, PVC (SWR) fittings such as bends of any radius, tee, shoe etc; fixed to PVC pipes, complete all as specified

S & F in repairs 20mm bore, gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified

S & F in repairs 25mm bore, gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified

S & F in repairs 32/40mm waste fittings for stainless steel sink (sink coupling), brass chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and flynuts, flange end bedded in red lead cement complete all as specified.

S & F in repairs 32/40mm waste flexible pipe 750 long for sinks, basins, etc. complete all as specified.

S & F in repairs vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor and fixed complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from 250 and not existing tanks 500 ltrs capacity water tanks, setting aside (or lowering if reqd)tanks and from mouths of circulating pipes, etc

S&F in repairs tank nipple suitable for HDPE water tank (minimum weight 20 mm - 45 gms) complete all as specified and directed .

Dismantling and disconnecting of existing CI soil vent pipe 100 mm bore fixed to wall, laid in trenches incl all fittings & accessories, all as directed.

S & F cast iron soil waste and vent pipe 100mm bore with or without ears fixed with chemical cement joints laid in trenches/floors or fixed in walls, all as specified.

Fixing only cast iron soil waste and vent pipe 100mm bore with or without ears fixed with chemical cement joints laid in trenches/floors or fixed in walls, all as specified.

Sealing only joints of cast iron pipes and fittings 75/100mm dia with chemical cement and making the joints leak proof complete all as specified

S&F in repairs oval access doors to cast iron pipes of 100mm bore with rubber washer & bolts & nuts as required complete all as specified

S & F in repairs CI bends any radius, 100mm bore, diminishing pieces or tapers, etc with or without oval access doors, complete all as specified

S & F in repairs 100mm bore CI branch pieces, double (spigot or socketed type) with oval access doors

Fixing only CI fittings 100mm bore of any type & description

Dismantling carefully cement concrete in floor, etc around floor traps or any other concealed fittings, ( replacing floor traps/fittings if required shall be deemed to be included in the quoted rates), sealing joints with solvent cement or other suitable materials and making joint leak proof and making good surfaces with PCC 1:2:4 or CM 1:3 (rates of repair/replacement of tiles in floor/wall shall be included in the quoted rates by the contractor), complete all as specified

M&L PCC 1:4:8 type D-2 using 40mm graded crushed/stone agg for foundations, filling & mass concrete, sub-base & sub-floors, etc. complete all as specified.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, ant-syphonage pipe, etc. complete all as specified

Fixing only in repair vitreous china wash basin/sink, of any description & size, excluding taps, wastes but including brackets complete all as specified

S&F three layers rotational moulded polyethylene water storage tanks (ISI marked) (cylindrical vertical top) hoisted and fixed in position 500 litre capacity including dismantling water tanks and removing to store 500 ltr. Capacity complete all as specified and directed.

S & F in repairs PVC lid (cover) for 500 to 1000 ltr capacity PVC water tanks with hinging & locking arrangement complete all as specified

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including necessary fittings, making connections and fixed in position complete in all respect as specified

S&F in repairs Jet spray CP, brass body with wall hook and 1 mtr SS pipe complete all as specified.

Fixing only in repairs vitreous china wash down water closet pan (pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, ant-syphonage pipe, etc. complete all as specified

Note:- Net contract sum shall be calculated after deduction of Sch of credit.

RAMA AUTOS

R K GOYAL & COMPANY

JAGMEET SINGH CONTRACTOR

M/s Kamal Constructions

AABIA CONSTRUCTION

Aman Enterprises

KULWANT RAI

ABHINANDAN ENTERPRISES