E tender 6 PDC Khaltsi

Amount

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : In Cement Mortar

Earth work in excavation by manual means over areas (exceeding 30 cm in depth,1.5 m in width as well as 10 sqm on plan) including getting out and disposal ofexcavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Coursed rubble masonry with hard stone (first or second sort) in superstructure above plinth level and upto floor five level. Masonry work (first sort), in cement mortar 1:6 (1 cement : 6 coarse sand)

Filling available excavated earth (excluding rock) in trenches, plinth, sides offoundations etc. in layers not exceeding 20cm in depth, consolidating eachdeposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.)trusses etc., including: Hot finished welded type tubes

Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting,

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of

Providing and fixing precoated galvanised iron profile sheets (size, shape andpitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied insingle length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDMseal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of

Supply and Fixing of 4 feet LED Tube Light of Make Crompton/ Havells including wiring and Light Control Point

Supply and Fixing on independent Board 02 NO 15 Amp Switch socket combination with wiring of 4 Sqmm

Supply and Fixing of Industial Exhaust Fan 16 Inchi Dia including wiring with 1.5 Sqmm wire complete and controlled by independent switch

Supply and fixing of service wire 16x2 mm including making all the connection complete

Material and Labour for Maintenance Free chemical Earthing System complete with 01 No UL 467 approved copper bonded earthing rods 2000 mm Long, backfill compond and conncetion with Alumunin Strip of size 25x3 mm from panel to the earthing. Making a pit of size 300 X300 mm for the earthing and placing a pit cover over it. All the accessories and arrangements as required by the standard dwawings be provided complete.

Abdul Qader (BID ID -137613)

M/S TASHI TUNDUP (BID ID -137917)