SPL REPAIR TO BLDG NO CB 345 CB 346 OF 5 JAK RIF 04 X WAITING SHED FLOOR PCC IN CR III 03 X TOILET WASHROOMS AT PC 06 AND PROVN OF SEPTIC TK SOAKAGE WELL AT ML 230 SHED FOR STUDENT AND CHEQUERED TILES SHED AT T 31 UNDER GE MIS MHOW

Amount

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of concrete or brick surface finished even and smooth without using extra cement including all necessary scaffolding lifiting arrangement upto 12m height including taking down of old cement plaster including removal of removing outside cantt area all as specified and directed by Engr-in-Charge.

M&L for rendering 15 mm thick in cement mortar 1:4 on fair faces of concrete or brick surface finished even and smooth without using extra cement including all necessary scaffolding lifiting arrangement upto 12m height including taking down of old cement plaster including removal of removing outside cantt area all as specified and directed by Engr-in-Charge.

M&L for rendering 5 mm thick in cement mortar 1:3 on fair faces of concrete surface of ceiling, finished even and smooth without using extra cement including all necessary scaffolding lifiting arrangement upto 12 m height including taking down of old cement plaster including removal of removing outside cantt area all as specified and directed by Engr-in-Charge.

M&L for two coats of oil bound distemper to newly plastered surfaces and applying a coat of wall care putty of 1 mm thick over plastered surface even and smooth including preparation of surfaces complete all as specified and directed by Engr-in-charge.

M&L for two coats of oil bound distemper of wall to old plastered surfaces and applying a coat of wall carre putty of 1 mm thick over plastered surface even and smooth including preparation of surfaces and removal of old treatment complete all as specified and directed.

M&L for applying three coats of white wash on ceiling including preparation of newly plastered surface complete all as specified and directed.

M&L for applying two coats of white wash on ceiling including preparation of old plastered surface complete all as specified and directed.

M&L for preparation and applying two coats of exterior weather proof paint (any colour/pattern as approved by GE) over a coat of alkali resistence primer up to 12m height in on new surfaces of plastered surfaces on wall, fascias, chajjas and roof projection etc including complete all necessary scaffolding lifiting arrangement upto 12m height complete all as specified and directed. Make: Asian :apex ultima , Nerolac : Suraksha or Make as specified in Particular Specifications.

S&F in repairs CPVC pipes SDR 11 fittings in trenches/wall with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 16mm including taking up or down steel/CPVC tubing with connections 15mm bore complete all as specified and directed.

S&F in repairs CPVC pipes SDR 11 fittings in trenches/wal with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs,unions etc.) of nominal bore 20mm including taking up or down steel/CPVC tubing with connections 20mm bore complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tank including, plastic lid cover, double layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 500 ltrs including making connections and 20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (min wt210 gram) complete all as specified and directed.

M&L for PCC 1:2:4, type B-0 (using 12.5mm graded stone aggregate) as in levelling course complete all as specified and directed.

Supply only Liquid Water proofing compound PIDIPROOF LW+ of Dr FIXIT or make as specified in PS complete all as specified and directed.

M&L for removing the existing APP membrane roof treatment of any description including screed bed /plastering of any thickness and removing the debris outside MD land etc. and carrying out the following complete water roof treatment complete all as specified and as per Manufacture's instructions:- (a) Cleaning the existing roof surface and brushing with neat cement slurry @ 3 Kg per Sqm area all as specified (b) Preparation of surfaces for applying bituminous primer (conforming to IS-3384-1965) @ 0.30 Kg/Sqm (c) Cutting out cracks to V- section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified. (d) Applying two coats of tack coat of Industrial bitumen grade of 85/25 at the rate of 1.2 Kg per sqm including cleaning surfaces (1st coat as a bonding material below membrane and 2nd coat on top of membrane (e) APP based polymeric membrane 3mm thick and minimum weighing 3kg/sqm and reinforced with polyster non wove fabric (weight not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and as per Manufacturer instruction (f) Applying two coats of bitumen based aluminium paint @ 0.15 Kg/Sqm for each coat over APP membrane including preparation of surface complete all as specified Note: WPT Shall be done through Manufcturer or through authorised applicator.

M&L for rendering 15 mm thick in CM 1:3 on fair faces of concrete or brick surface finished even and smooth without using extra cement including all necessary scaffolding lifiting arrangement upto 12m height complete all as specified and directed by Engineer-in-Charge.

Taking down door shutter with frame n exc 1.5 Sqm each without taking of shutter from the frame complete all as specified and directed.

Taking down chowkats or frames with shutters (w/o taking off shutters from the frames ) exceeding 1.5 sqm and not exceeding 4 sqm each, including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish(without any extra cost to Govt), & removing from site all as specified and directed by Engr-in-charge

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each complete & removing from site complete all as specified and directed.

S&F factory made steel window, with side hung shutter including projecting hinges with steel handle, stay complete devetailed or welded complete all as specified and directed.

S&F factory made steel window, with side hung shutter including projecting hinges with steel handle, stay complete without glazing bar and guard bar devetailed or welded complete all as specified and directed.

S&F factory made pressed steel frames of size 105x60mm made out of PBI sheet 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinge, lock strike plate etc. complete including bottom of each chowkat to be welded with 02 nos 25x25x3mm angle iron projecting 10cm one either side including one shop coat of red oxide chrome primer complete all as specified and directed.

S&F second class Hard Wood shutters 35mm thick, plain framed panelled shutter factory made (two panel) with lock rail & panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS:1003 complete all as specified and directed.

S&F mild steel butt hings medium weight 100 mm long complete all as specified and directed.

S&F Aluminium handle cast type, anodised size 150mm long, D type complete all as specified and directed.

S&F Aluminium anodised barrel tower bolts, with bright bolt and fixed 200mm complete all as specified and directed.

S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F galvanised MS wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staples including takingout old wire mesh from steel window and fixing old steel flats and nut complete all as specified and directed.

S&F in repairs floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, overall length of cover plate as 150mm complete all as specified and directed.

S&F in repairs curtain rod 25mm stainless steel/choromium plated with fixing brackets, side ball stops, rollers, etc complete all as specified and directed.

Hacking out old broken glass of any thickness, size, quality or description from the wooden/ steel frames glazing with puttyor fixed with wooden beads complete all as specified and directed.

S&F 3mm thick ordinary glass sheet quality and glazing with oil putty in square n. exc 0.5 sqm in each pane including punching or drilling out old glazing pins or spring clips and providing and fixing new clips or pins, including scaffolding to reach up to 4 story buildings complete all as specified and directed.

S&F powder coated aluminium sliding glazed window with three track shutter sliding (two shutters glazed and one shutter wire mesh) shall be two part as upper patr shall be three movable shutter and lower part consist three shutter (one openable in centre and both side fixed type shutter with frosted glass) with following specification and making good the adjacent side of jambs of windows by plastering in CM 1: 3 even and smooth complete etc . shifting of existing cooler stand where required (Make : Jindal/Hindalco /make as specified in Particular Specification) complete all as specified and as directed by Engr-in-charge. (i) Windows frame of cross section 101mm x 44mm x 1.5mm thick. (ii) Three way track for sliding shutters of cross section 91.8mm x 31.75mm x1.1mm thick. (iii) Sliding shutter frame of cross section 40 x 18 x 1mm thick. (iv) 4 mm thick glass superior quality. (v) IDPE Rubber guasket for fixing of glass. (vi) Locking cleats per shutter -01 Nos. (vii) Sliding rollers per shutter - 02 Nos. (viii) Stainless steel wire cloth 0.30mm nominal dia of wire and average width of aperture 1.40mm for shutters 01 Nos. (Ix) fixing screw for frame with wall per windows- 08 Nos.

S&F powder coated aluminium door frame of size 101.60 x 44.45 x 1.50 mm of approved manufacture fixed to floor, wall with real plug and screws and shutter partly glazed and partly particle Board with frame of anodized aluminium is using with both side portion of door shutter in permanent fixing type and middle of part portion glazed and open shutter type door including mortice lock, hydraulic door spring (ISI marked as approved), door handle tower bolt, hinges and glass pane not less than 5 mm thick fixed with rubber gasket and aluminium beading/glazing clip size 19.00 x 17.30 x 0.70mm (Weight 0.097 Kg/RM of both side) shutters with top, lock rail and vertical members of size 83.50 x 44.45 x 1.50mm and bottom members of size 114.30 x 44.45 x 1.50 mm complete all as specified and directed. (Auminium section Make : Jindal/Hindalco /make as specified in Particular Specification)

S&F in repairs mild steel framed work such as grills , gratings, etc., with ends of bars shouldered and/ or riveted, or forged in to spikes; framed guard bars ; barred iron doors; ladders; framed balusters ; walk ways ; railings; frame work of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F in repairs waste coupling of PTMT (half or full threaded) of bore dia 32 mm discharge pipe complete all as specified and directed.

S&F in repairs vitreous china wash hand basin white flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of tap, waste fitting etc complete all as specified and directed.

S&F in repairs Tubular towel rail, 20mm dia, D type 60cm long between flanges of brass chromium plated complete all as specified and directed.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs corner glass shelf of 30mm dia with aluminium bracket and railing superior quality complete all as specified and directed.

S&F in repairs LDPE pipe 32mm bore fixed to wall/ceiling with bends/elbow complete all as specified and directed.

S&F in repairs Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20 mm bore complete all as specified and directed.

S&F in repairs 15 mm dia bore pillar tap cast copper alloy with capstan heads chromium plated, fancy type, screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs angle/stop valve of cast copper alloy screwed down high pressure with crutch or butterfly handle screwed bother ends for iron pipe or for uniorns and fixed 15 mm bore complete all as specified and directed.

S&F PVC connection 15mm, 450mm long with nuts and washers complete all as specified and directed.

S&F CP Grating doom 100/125mm dia with or without hole chromium plated complete all as specified and directed.

S&F PVC Waste pipe 32 mm dia and suitable length straight or flexible type for wash hand basin / sink complete all as specified and directed.

S&F in repairs 5mm thick colour prelam PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining fixed over 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing and Solid PVC Partitions inclusive of Solvent Cement and fixing at site and PVC sheet 1 mm thick in lipping in case of PVC sheet is heat bent as lipping on the edges of doors/corner/window complete all as specified and directed.

Dismantling floors hearth or wall tilling including cement mortor bedding (but not backing) removing unserviceable materials outside MOD area and rubbish off the premises complete all as specified and directed.

M&L for glazed ceramic coloured tiles 300x450x7 to 8 mm thick on vertical surface as in skirting,dado set and jointed with neat cement slurry and pointed in white or coloured cement to match with the surface over and including 10 mm thick plastering in CM 1:4 complete all as specified and directed .

M&L for Non skid/mate finished ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 sqm but not exc 0.38 sqm,in floors etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per item No 51.00 above but in skirting over and including 10 mm thick rendering in CM 1:4 complete.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons, platform, stairs etc. complete including removal of demolition material to store or from site complete all as specified and directed .

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing unserviceable material outside cantt area complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregates) as in copings, bed block etc. and in similar works including weathering,slightly rounded or chamfered angles and throating and necessary form works complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in floor/plinth protection laid in suitable panels finished even and fair all as specified and making 6mm Joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 Gde and three part of sand (all by weight) complete all as specified and directed.

M&L for cement concrete 1:5:10, type E2 (using 40mm graded stone aggrregate) in foundations, filling and mass, sub base concrete complete all as specified and directed.

M&L for 60 mm thick Machine pressed precast conctete interlocking paver block in glossy finish with grey/coloured cement and pigment , any shape and size confirming to IS 15658-2006, M-35 Grade laying over and including 50 mm thick stone dust/sand cushion complete all as specified and directed.

M&L for complete removal of old treatment and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489-2004, Alkali and fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) 1.43 litre/10sqm over and including priming coat of exterior primer applied @ 0.90 litre /10sqm complete all as specified and directed.

M&L preparation of new or previously untreated wooden surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of new or previously untreated steel surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old treated steel surfaces of any description exceeding 10cm width or girth and applying one coat of synthectic enamelled paint complete all as specified and directed.

M&L for preparation of old treated wood or wood based surface of any description exceeding 10cm width or girth and applying one coat of synthectic enamel paint complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) bend with access door complete all as specified and directed.

S&F 1.25 mm thick Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified and directed.

M&L for brickwork with using fly ash bricks,straight or curved on plan exc 6m mean radius,built in cement mortar 1:4 including demolition of old brick work at any description complete all as specified and directed.

Exacavation in trenches, n. exc 1.50m wide and n. exc 1.50 m in depth for foundation etc or for shaft ,wall, cesspits, manholes, pier holes etc. n. exc 10 Sqm on plan and n. exc 1.5m in depth in any type of soil etc complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in mass concrete, foundation filling, post hole, PCC bed and any other location etc. complete all as specified and directed.

S&F reinforced concrete pipes 150 mm bore, class NP2 , laid and jointed complete with collars complete all as specified and directed.

S&F 200mm reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) concrete bed to drain pipe including packing under and haunching against side of pipe for 150 mm bore of pipe complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) concrete bed to drain pipe including packing under and haunching against side of pipe for 200 mm bore of pipe complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm with any type of soil complete all as specified and directed.

Removing excavated material to a distance n exc 50m and deposited where directed at a level n. exc 1.50m above the starting point complete all as specified and directed.

M&L for providing pre-cast cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in landings, cover slabs, chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces etc set in cement mortar 1:4 including chamfered weathering, throating etc with necessary form work complete all as specified and directed.

S&F mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and as directed.

S&F in repairs PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints with solvent cement fixed to walls/ trenches or in floors incluidng clamping complete all as specified and directed.

S&F in repairs PVC (SWR) 110 mm bore pipes single socketed in any length with rubber ring joints with solvent cement fixed to walls/ trenches or in floors incluidng clamping complete all as specified and directed.

S&F in repairs 110 mm dia bore PVC (SWR) bends any radius with solvent cement joints, fixed to complete all as specified and directed.

S&F in repairs 75 mm dia bore PVC (SWR) bends any radius with solvent cement joints, fixed to complete all as specified and directed.

M&L for construction of septic tank for 100 users complete including excavation in ordinary soil, foundation in PCC 1:2:4, brick work in cement mortar 1:4 slab covers including RCC precast manholes cover having 6mm plate embedded all around / Fibre reinforced cover with angle iron frmae Vent shaft and sludge chembers etc. complete for 100 users, complete all as specified in drawing No TD-TRG NO CEJZ/TD/57 sheet No 1/4 to 4/4 dated 05/05/2000 complete all as specified and directed.

M&L for construction of soakage well of complete of size 3.00m Dia X3.00m deep complete including excavation in any type of soil, foundation in PCC 1:3:6 wells of Honey comped and solid in M-25 design nix concrete,including intercepting chember,screen chember brick work in cement mortar 1:4 , RCC cover slab in M-25 design mix, RR measonary, filling with brick bats, complete all as specified in drawing No TD-DRG NO CEJZ/TD/58, sheet No 1/1 dated 05/05/2000 complete all as specified and directed.

Demolition of brick work / stone boulders masonry built in cement mortar incl all Quoins , archeas, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed

M&L for brick work with flyash bricks straight or curved on plan exc. 6.00m mean radius built in cement mortar 1:6., etc complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on any faces of brick or concrete surfaces finish the surface even and smooth without using extra cement all as specified and directed.

Excavation in post holes ( or similer holes) each N.Exc 0.50 cum getting out,ramming earth or briken rubble mixed with earth around, in layars N.exc 25cm watering anf removing surplus soil to a distence N.Exc 50m and making good the disturb surface in soft/loose soil complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L for 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved clour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/shape made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, M-35 grade complete all as specified and directed.

M&L for cement concrete 1:4:8 type D2 (using 40mm graded stone aggrregate) as in foundations, filling and mass concrete, sub base complete all as specified and directed.

M&L for precast factory made cement concete block Size (Kerb stone) type B1 1:2:4 (using 20mm graded stone aggregte ) fixed dry mortar complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint on concrete surface over coat of primer including prepartion of new surface over 10cm width or girth complete all as specified and directed.

M&L for applying three coats of white wash on wall surface incl preparation of new plastered surface complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of exterior weather proof paint (any colour/pattern as approved by GE) over a coat of alkali resistence primer up to 12m height in on wall, fascias, chajjas and roof projection etc including complete all necessary scaffolding lifiting arrangement upto 12m height complete all as specified and directed. Make: Asian :apex ultima , Nerolac : Suraksha or Make as specified in Particular Specifications.

S&F mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door ittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete) Fe 410 -W (GdeE- 250) quality A complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18 to 20mm thick over and including 20 mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slury mixed with pigment to match the shade of the slab incluiding rubbing and polishing complete all as specified and directed.

M&L for machine cut kota stone slab 18 to 20mm thick over and including 10 mm thick rendering in CM 1:3 on vetical surface over laid and jointed with grey cement slury mixed with pigment to match the shade of the slab incluiding rubbing and polishing complete all as specified and directed.

M&L for 75mm thick cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in floor laid in suitable panels finished even and fair using extra cement complete all as specified and directed.

S&F Glass dividing strips 3 mm thick and 38mm width, inserted in position complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tank including, plastic lid cover, double layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 1000 ltrs including making connections and 20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (min wt210 gram) complete all as specified and directed.

S&F in repairs galvanised steel water tubing medium grade 15mm bore with all fittings such as bend, elbow, socket reducer etc fixed to walls and ceilings or laid in floors jointing and testing complete all as specified and directed.

S&F in repairs galvanised steel water tubing medium grade 20mm bore with all fittings such as bend, elbow, socket reducer etc fixed to walls and ceilings or laid in floors jointing and testing complete all as specified and directed.

S&F in repairs galvanised steel water tubing medium grade 25mm bore with all fittings such as bend, elbow, socket reducer etc fixed to walls and ceilings or laid in floors jointing and testing complete all as specified and directed.

M&L for Granite 18 to 20 mm thick (of any type) work (table rubbed and polished) for wall lining (Veneering to wall) and laid on cill of parapit wall over and including 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite colour Red or brown complete all as specified and directed.

M&L for rendering 10mm thick plaster in CM (1:6) on faces of brick work or concrete surfaces, finished even and smooth without using extra cement including taking down of old cement plaster complete all as specified and directed.

M&L for rendering 15mm thick plaster in CM (1:4) on faces of brick work or concrete surfaces, finished even and smooth without using extra cement mixed with Dr fixit pidiproof LW 200ml/50Kg of cement and finished even and smooth without using extra cement and including of taking down old cement plaster all as specified and directed. Note: WPC shall measured and paid separately.

M&L for rendering 5mm thick in CM 1:3 as in soffits of ceiling and RCC cjhaja/ Facia roof projections finished fair & even all as specified including taking down old plaster complete all as specified and directed.

S&F in repairs 10 Ltr capacity,PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with and including 32 mm dia PVC flush pipe complete all as specified and directed.

S&F in repairs 18mm thick factory made 100% solid rigid PVC (Poly Vinyl Chloride) foam sheet Prelam colour having density of 600kg/cbm manufactured by an Iso 9001-2015 certified company.Termite proof,water proof and flame retardant PVC sheet,manufactured by single layer extrusion process for one side prelaminated solid PVC foam sheet. PVC film laminate should be pasted on PVC sheet with suitable adhesive and approved shade complete all as specified and directed.

S&F in repairs vitreous china urinal half stall type 350x390x600 mm (minimum) height with including spreader for urinal ,providing & fixing of plugs bedding against wall in cement mortar 1:2 pointing around urinal back in cement mortar complete all as specified.

S&F in repairs vitreous chaina wash down water closet pan (pedestal pattern), white including pedestrial pan and trap, including connecting to drain or outgoing pipe and to flushing pipe, antisyphonage pipe etc complete all as specified and directed.

S&F in repairs white coloured Plastic water closet seat, back, closed pattern with flat bottom , and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repairs 15mm dia long body Bib tap chromioum plated with crutch or butterfly handle sorewed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs PVC (SWR) nahani trap with grating having diameter of outlet 75 mm including joining to waste pipe with solvent cement complete all as specified and directed.

S&F in repairs 110 mm dia bore PVC (SWR) bends with acess door any radius with solvent rubber ring joints, fixed complete all as specified and directed.

S&F in repairs 75mm dia bore PVC (SWR) bends with acess door any radius with solvent rubber ring joints, fixed complete all as specified and directed.

S&F in repairs 110 mm dia bore PVC (SWR) junction single, single (T) equal or unequal with acess door with solvent rubber ring joints, fixed complete all as specified and directed.

S&F in repairs 75mm dia bore PVC (SWR) junction single, single (T) equal or unequal with acess door with solvent rubber ring joints, fixed complete all as specified and directed.

S&F in repairs 110 mm dia bore PVC (SWR) branch piece single (single Y) equal or unequal with rubber ring joints, fixed complete all as specified and directed.

S&F in repairs 75mm dia bore PVC (SWR) branch piece single (single Y) equal or unequal with rubber ring joints, fixed complete all as specified and directed.

S&F in repairs 110 mm dia bore PVC (SWR) vent cowl rubber ring joints, fixed complete all as specified and directed.

Cutting chases in brick wall for concealed water tubing, pinning in, making good of facings where required and pointing in cement mortar 1:3 to ends or edges etc, cutting not exceeding 10 cm width or girth complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in subbase of tiles/ stones complete as in levelling work etc complete all as specified and directed.

S&F powder coated aluminium ventilator cross section conforming to IS 63.5x38.10x1.5mm consisting of two partions upper portion shall have louvers with 3mm thick pin headed glass and aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56m fixed with aluminium beads and securing on outer face of frame and lower portion of ventilation shall be fixed with 3mm thick pin headed glass with IDPE rubber gasket including aluminium beads, including preparation of jombs all around in CM 1:3 finishing even and smooth complete all as specified and directed.

S&F factory made 100% solid WPC (Wood polymer composite) Door frame 85mm X 45mm (Moulded) single rebated made from wood polymer composite (single extruded process material comparison of virgin PVC polymer of k value 57-60 (Suspension grade) , calcium carbonate and natural fibers (Wood powder/rice husk/wheat husk) and Non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treaded star headed screws having minimum frame density of 750 kg/ cbm, an ISO 9001-2015 certified company , having good screw holding capacity (screw withdrawal strength of (Min 990 N ), minimum compressive strength of 58n/mm2, Modulus of elasticity 900N mm2 and resistance to spread of flame of class A category with property of being Termite/ borer proof , water/ moisture proof and fire retardant & fixed with position with SS dash fasteners / Hold fast of required dia and length , all as per specifications drawings as directed by the Engineer-In-charge ,Material test certificate and authentication should be compulsory provided by the manufacturing company including hold fast or fasteners complete all as specified and as directed.

S&F factory made 30 mm thick 100% solid WPC (wood polymer composite) laminated flush door shutter of required size comprising of virgin PVC resin of K value 57-60 ( suspension grade), Calcium carbonate and natural fibers ( Wood powders / rice husk/wheat husk) and non toxic additives made from extension process WPC foam sheet single extruded (Inner) with having minimum density not less than 650 kg kg/cbm, an ISO 9001-2015 certified company , having good screw holding capacity (Screw withdrawal strength of 200 N (Face) & 1100 N (Edge) minimum compissive of 50N/mm2 Modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category property of being Termite/ borer free , water/ moisture proof and fire retardant WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws , all as per direction of Engineer-In-charge ,Material test certificate and authentication should be compulsory provided by the manufacturing company complete all as specified and as directed.

S&F 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F aluminium 150 mm long anodised barrel tower bolts ISI marked of extruded section and fixed complete all as specified and directed.

M&L for chequered cement concrete tiles with grey cement and pigment of size 20cmX20cmX25mm thick ,set and jointed and pointed in neat cement slurry in floor etc over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

S&F in repairs Stainless Steel Wall Mount Case with Soap Holder & Brush Holder fixed to wall all as specified and directed by Engr-in-Charge. Make : Make Marc/Jaquar/Prayag or make as specified in Prticular specifications

S&F in repairs health faucet 15 mm dia with flexible pipe of 1.25m length including abs wall hook for EWC complete all as specified and as directed.

S&F in repairs 30 mm width of flaps (when open) Continous (piano) hinges , mild steel, bright finish or electrogalvanised complete all as directed and specified.

S&F in repairs Plain fillets. Square, rectangular or triangular in section, clean swan, secured with nails or brads 2nd class softwood n. exc 3sq.cm, complete all as specified and as directed.

S&F in repairs 15 mm bore two way bib taps long body, chromium plated cast copper alloy long body , screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S&F in repairs over head shower with arm & flnge of chromium plated with or without swivel joints, any size, including fixing to 15mm dia steel pipe for required length or union complete all as specified and directed

Excavating in trenches, n exc 1.50 m wide and n exc 1.50 m in depth; for foundation, etc. n exc 10 sq m on plan and getting out in any type of soil soil complete all as specified and directed

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new/old surfaces and 1mm thick wall care putty on wall complete all as specified and as directed.

M&L for preparation of surface and applying two coat of acrylic emulsion with roller on new treated surfaces of wall etc complete all as specified and directed.

M&L for chequered cement concrete tiles (glossy finish) 40 cm x 40 cm x 25mm thick set jointed and pointed in neat cement slurry in floors with grey cement and no pigment laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) and necessary PCC coping type C1 1.3.6 including dismantling of old laid bedded and pointed in any mortar Stone slabs and tles of any description or thickness in floors, aprons etc. complete all as specified and directed.

S&F mild steel work (Tubular, square/rectangular hollow section) as in purline, rafter and wind ties, cleat roof trusses etc including securing bed plate, plat iron fillets for securing wire mesh etc including all necessary drilling bolting or riverting, etc, and similar work conforming to IS 1161-1979 dge St-240 complete as directed and specified.

S&F Rolled mild steel Fe 410 -W (Gde- E-250) quality- A as Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. Including cleats, brackets, etc. etc complete all as specified and as directed.

S&F false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of size 595 x 595 mm of approved texture, design and patterns pinhole 8mm thick semi perforated square edge tile having NRC (Noise Reduction coefficient) of 0.50 (minimum) Light reflectance of 85% (minimum). Non combustible as per BS: 476 (PART-4), fire performance as per BS: 476(PART 6&7), humidity reistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, in true horizontal level suspeded on interlocking metal powder coated T-Grid of hot dipped galvanized iron section on Silhouetter profile, rotary stitched double webbed white with 1 mm reveal profile (White/black), comprising of main-T runner of size 15 x 32mm of length 3000m, cross-T of size 15 x 32 mm of lenght 1200mm and secondary intermediate cross-T of size 15 x 32 mm of lenght 600mm to form grid module of size 600 x 600 mm, from ceiling using galvanized mild steel item, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod and L-shape level adjuster of size 85x25x2 mm. Galvanized iron perimeter wall angle of size 19 x 19mm-of-length 3000 mm to be fixed on periphery wall /partition with the help of plastic rawi plugs at 450mm centre to centre and 40mm long dry wall S.S. screws. The work shall carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc . Removing materials to store for keeping in safe custody or for taking credit ( credit a for above items should be made as per condition seperately ) and making good distrubed surfaces of walls, floors etc.

M&L for Point wiring using approved colour coding as as per IS in repairs with FR LSH PVC insulated PVC unsheathed electric cable 1100V grade ISI 694 marked down through single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area drawn in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20mm dia with all conduit accessories in concealed/or PVC conduit as per site reqirement wiring system by cutting of wall and making good and matching disturbed surface of wall with existing surface of wall (cutting except on ceiling for fan point only, on ceiling instead of PVC conduit surface casing caping will be used) & 1.5 sqmm green FR LS PVC insulated unsheathed copper conductor as earth wire connected to earth dolly by providing lugs including galvanised boxes and bakelite sheet for mounting switches, sockets, fan regulators etc for the following:- Make of PVC conduit/Casing Caping:- Plaza/Finolex/Polycab/Kalinga/Jindal/Asian (a) One light point/fan point controlled by one switch.

(b) One Exhaust fan point controlled by one switch

(c) One 5amps socket out let point controlled by one switch on same board with other switches.

(d) One 5amps socket out let point on independent board controlled by one switch.

All as per item No 148.00 above but using FR LSH PVC insulated unsheathed 2.5 sqmm cross sectional area cable for phase /neutral & for earth 2.5 Sq mm green FR LSH PVC insulated cable for 15 amps socket point on independent board controlled by one switch.

All as per item No 148.00 above but using 4.0 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for geyser point/AC point connecting to metal plug and socket DB incl necessary running of 4.0 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

S&F Modular switch, single pole one way 5/6 Amp 240 volt complete all as specified and as directed.

S&F Modular socket type 5 pin, 6 amps, 230 volts complete all as specified and as directed.

S&F Modular switch single pole one way 15/16 Amp 240 volt complete all as specified and as directed.

S&F Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module complete all as specified and as directed.

S&F Modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module complete all as specified and as directed.

S&F in repairs electronic Fan regulator step type complete all as specified and as directed.

S&F ceiling rose surface bakelite three terminal complete all as specified and as directed.

S&F in repairs integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7PN1W018 / Bajaj cat Pt No. BCLSB 18WH / Wipro /Philips / Crompton / Make as specified in Particular Specifications.

S&F in repairs integrated LED tube light fitting 1x9/10 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square box complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7IN1W009 / Bajaj Cat Pt No. BCLSB 10 WH / Wipro /Philips / Crompton / Make as specified in Particular Specifications.

S&F in repairs LED street light fittings 1x35 Watt, 5700K complete fitting having pressure dia cast aluminium housing with heat resistant toughened glass & IP 65 /66protection fixed on and including sufficient length and appropriate size GI bracket with all accessories duly connection with three core flexible copper cable complete all as specified and directed. Make:- Havells Cat No.LHEXAYP7PN6K030 Crompton Cat No. LSTO-25-CDL / Bajaj Cat No. BCLST 25W LED IV2 / / Wipro /Philips / Crompton / Make as specified in Particular Specifications.

M&L for sub main wiring (in replacement) with two runs of single core FR LSH PVC insulated unsheathed cable 1100 volts grade, 4 Sqmm size with multistranded copper conductor, drawn in and including surface non metallic rigid PVC conduit not less than 25mm dia and all fittings like bends, tees, saddles etcincluding one run of FR LS PVC insulated unsheathed 4 sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly complete. Note : Two runs of 4 sqmm single core multistandred copper conductor and one run of 4 sqmm earth conduit conductor and one length of PVC conduit and its accessories shall be measured as one unit length.

S&F in repairs double door SPN DBs eight way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified and directed by Engr-in-Charge.

S&F in repairs MCB SPN 6 to 32 amps 10 KA, B-series including connection with suitable size aluminium/copper lugs complete all as specified and directed by Engr-in-Charge.

S&F in repairs MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-in-Charge.

S&F exhaust fan 250mm sweep, AC single phase 230 Volts, non metallic type, complete with louver including electric connection with suitable size copper conductor cable, clamps, nuts, bolts etc including making hole of appropriate size in the existing brick wall and making good the disturbed wall and matching with the existing surface of wall complete all as specified and directed by Engr-in-Charge. Make : Havells Model: Ventil Air-DX white / /Bajaj/Crompton / make as specified in Particular specifications.

S&F in repairs LED round light fitting 15W recess mounting type, white light LED or warm light LED 6500K as per site requirment complete with driver duly connection with copper cable etc. Make, Havells Cat No. LHEBLDP7IN1W015 Bajaj Cat Pt No. BGSLO SLEEK 15W WH RD, / Crompton, Wipro . Note :- Ceiling cutout ø 180 mm, height 23 mm ±1 mm for 15 W / Wipro /Philips / Bajaj/ Make as specified in Particular Specifications.

S&F in repairs Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 35 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe 40 mm dia medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge. Make:- Cat No ENXT P 36L WH CR PC SD of Bajaj / Havells / Wipro /Philips / Crompton / Make as specified in Particular Specifications.

S&F in repairs double door TPN DBs four way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified and directed by Engr-in-Charge.

S&F in repairs MCB TPN 40 to 100 amps 10 KA, c-series including connection with suitable size aluminium/copper lugs complete all as specified and directed by Engr-in-Charge.

S&F in repairs metal clad box suitable for 230 volt 50 Hz for AC connection three pin and socket with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed

M&L for Earthing in repairs complete with galvanized steel earth plate electrode 60cm x 60cmx 6.3 mm thick buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with the top edge of the earth plate not less than 1.5 meter below normal ground level connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or of steel all as shown in electrical plate No.5 of MES SSR parts-I and including excavation & earth work in any type of soil , disposal of soil , providing alternate layers of charcoal and common salt, construction of PCC earth chamber in mix 1:3:6 type C-1 with 40 mm thick RCC 1:2:4 type B-J cover reinforced with 8mm dia MS bars both ways with lift hook made out of 8 mm dia bar, watering arrangement with funnel and wiremesh and watering pipe of 20mm dia GI light grade and 15mm dia light grade pipe for earth lead protection and testing on completion, complete all as specified and directed.

RK CONSTRUCTION (BID ID -3493525)

sunway associates (BID ID -3486439)