Construction of PHC building at Janori village, Taluka Dindori, District Nashik under CSR 2024-25

HINDUSTAN AERONAUTICS LIMITED AIRCRAFT OVERHAUL DIVISION, NASIK WORKS AND SERVICES DEPARTMENT

Name of work: CONSTRUCTION OF PHC BUILDING AT JANORI VILLAGE, TALUKA DINDORI, DISTRICT NASHIK UNDER CSR 2024-25.

Tender No.:NK/FW/CSR-1596/2024-25

NIT NO. : NK/FW/534/2024-25

Estimate Value : Rs. 154.42 Lakhs

PRICE BID/ COMMERCIAL BID PART-B

Name of the Tenderer:

Sl. No Specification Quantity Unit Rate in Figs [Excluding GST] Rate in words Amount

Preamble: (1) The subject work has been called on works contract basis and prevailing GST for same is 18%. Any change in GST +/- during the currency of contract shall be on HAL account. The tenderer shall abide by prevailing GST act. (2) This BOQ specifications have to be read in conjunction with detailed technical specification and tender drawings if any. (3) The tenderer has to quote percentage above / below against the total amount considering the specified standard rates. If the contractor does not quote any percentage above / below on the total amount, the tender shall be treated as invalid and will not be considered. (4) The quoted percentage for the works mentioned below, shall be taken into consideration for evaluation of the tender. The lowest offer (L-1) will be determined considering the total amount including GST based on the quoted percentage.

1 Demolishing cement concrete of nominal concrete 1:3:6 or richer mix (including equivalent design mix) manually/ by mechanical means in any position including disposal of material/debris off the site within 50 metres lead and stacking for further disposal all complete and as per direction of EIC. 1.00 Cum 2227.96 Rupees Two Thousand Two Hundred Twenty Seven and Ninety Six Paise Only 2227.96

2 Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m all complete as directed and as specified by EIC. Note: The item will not be paid whereever any other excavation items are paid. 500.00 Sqm 31.26 Rupees Thirty One and Twenty Six Paise Only 15630.00

3 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation, trenches, drains or like (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lifts , including getting out the excavated soil and disposal of surplus excavated soil , within a lead of 50 m all complete and as directed by EIC. Note: Soil, if any, which is required for refilling shall be stacked at site as per the directions of EIC.

a) All kinds of soil 141.00 Cum 238.25 Rupees Two Hundred Thirty Eight and Twenty Five Paise Only 33593.25

b) Ordinary rock 70.00 Cum 579.32 Rupees Five Hundred Seventy Nine and Thirty Two Paise Only 40552.40

c) Hard rock (Blasting Prohibited) 1.00 Cum 1393.98 Rupees One Thousand Three Hundred Ninety Three and Ninety Eight Paise Only 1393.98

4 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift as directed by Engineer-in-charge.

a) All kinds of soil 145.00 Cum 162.46 Rupees One Hundred Sixty Two and Forty Six Paise Only 23556.70

b) Ordinary rock 6.00 Cum 456.63 Rupees Four Hundred Fifty Six and Sixty Three Paise Only 2739.78

5 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations, floors, etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by mechnical/power ramming/compacting and watering, lead up to 50 m and lift upto 1.5 m all complete as directed by EIC. 285.00 Cum 179.39 Rupees One Hundred Seventy Nine and Thirty Nine Paise Only 51126.15

6 Supplying, stacking and filling murum (including royalty) in trenches, plinth, sides of foundation, floors,etc in layers not exceeding 20cm consolidating each deposited layer by mechnical/power ramming/compacting and watering, lead up to 50 m and lift upto 1.5 m all complete as directed by EIC. 150.00 Cum 882.54 Rupees Eight Hundred Eighty Two and Fifty Four Paise Only 132381.00

7 Removing the excavated surplus soil / material / dismantled debris including loading, conveying and depositing at a place at a distance upto 1KM from starting point as directed and spreading & levelling all as directed by EIC. 120.00 Cum 159.30 Rupees One Hundred Fifty Nine and Thirty Paise Only 19116.00

8 Supplying chemical emulsion in sealed containers including delivery as site Chlorpyriphos/lindane E.C. of 20% as directed. 50.00 Litre 214.86 Rupees Two Hundred Fourteen and Eighty Six Paise Only 10743.00

9 Diluting and injecting chemical emulsion for post-constructional anti-termite treatment with Chlorpyriphos/lindane E.C. 20% with 1% concentration along external wall where the apron is not provided using chemical emulsion @ 7.5 litres/Sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding , top surface of plinth, junction of wall & floor, along external perimeter of building, expansion joints, etc. 100.00 RM 35.61 Rupees Thirty Five and Sixty One Paise Only 3561.00

10 Providing and laying in position 1:2:4 cement concrete (1 cement : 2 coarse sand (Zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) including mixing, laying, curing, fininshing to level & line etc all complete for all works up to plinth level as specified and as directed by EIC. 75.00 Cum 7210.84 Rupees Seven Thousand Two Hundred Ten and Eighty Four Paise Only 540813.00

11 Providing centering and shuttering including strutting, propping, etc.and removal of formwork for plain or reinforced cement concrete straight, horizontal, sloping as required including all cutting & waste, centering, bracing, all complete as specified & as directed by EIC for:

a) Footings, foundations, bases of column etc. for mass concrete. 200.00 Sqm 358.92 Rupees Three Hundred Fifty Eight and Ninety Two Paise Only 71784.00

b) Columns, Pillars, Piers, Abutments, Posts and Struts 280.00 Sqm 879.84 Rupees Eight Hundred Seventy Nine and Eighty Four Paise Only 246355.20

c) Lintels, beams, plinth beams, girders, bressumers and cantilevers 920.00 Sqm 674.00 Rupees Six Hundred Seventy Four Only 620080.00

d) Suspended floors, roofs, landings, balconies , shelves, chajja, etc. 400.00 Sqm 848.67 Rupees Eight Hundred Forty Eight and Sixty Seven Paise Only 339468.00

e) Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. 5.00 Sqm 771.11 Rupees Seven Hundred Seventy One and Eleven Paise Only 3855.55

f) Stairs, (excluding landings) except spiral-staircases 55.00 Sqm 700.13 Rupees Seven Hundred and Thirteen Paise Only 38507.15

12 Providing and laying in position ready mixed or site batched design mix cement concrete of M25 grade (minimum cement content of 330 Kg/Cum) for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, ordinary portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge.

a) All works upto plinth level 100.00 Cum 8699.27 Rupees Eight Thousand Six Hundred Ninety Nine and Twenty Seven Paise Only 869927.00

b) All works above plinth level upto floor V level 115.00 Cum 9024.78 Rupees Nine Thousand Twenty Four and Seventy Eight Paise Only 1037849.70

13 Providing and laying in position ready mixed or site batched design mix cement concrete of M30 grade (mimimum cement content of 350 Kg/Cum) for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge.

a) All works upto plinth level 5.00 Cum 8837.43 Rupees Eight Thousand Eight Hundred Thirty Seven and Forty Three Paise Only 44187.15

14 Providing and laying in position MS reinforcement TMT of grade Fe-500D or more, for R.C.C. work including straightening, cutting to required length, bending, hooking, cranking, placing in position and binding with MS wire (annealed) not less than 0.9 mm Dia. or securing with clips including necessary lapping, spacers/cover blocks complete all as specified and as directed by EIC. 21500.00 Kgs. 98.72 Rupees Ninety Eight and Seventy Two Paise Only 2122480.00

15 Supplying, stacking, laying, spreading & compacting stone aggregate in required thickness hand picking, consolidating with mechnical vibrator in stages with proper grade and camber, level, applying and brooming requiste type of screening/binding material to fill up interstices of coarse aggregate, watering and compacting to required density all complete as per direction of Engineer-in-charge. Note: binding material shall be with stone dust to be filled in interstices of coarse aggregate.

a) Stone aggregate of size 90mm to 63mm 70.00 Cum. 2873.99 Rupees Two Thousand Eight Hundred Seventy Three and Ninety Nine Paise Only 201179.30

b) Stone aggregate of size range 63mm to 45mm 10.00 Cum. 2450.83 Rupees Two Thousand Four Hundred Fifty and Eighty Three Paise Only 24508.30

16 Providing and constructing brick masonry in subclass 'B' Bricks , straight or curved on plan to any radius built in CM 1:4 above or below ground at any height and level including necessary scaffolding, curing , providing reinforcement, if required, all complete as specified and as directed by the EIC. (Brick of class designation 35kgf/cm2)(MS reinforcement will be paid separately under respective item). 15.00 Cum 9289.32 Rupees Nine Thousand Two Hundred Eighty Nine and Thirty Two Paise Only 139339.80

17 Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry with 150mm to 300 mm thick with Grade-I AAC blocks of density 551 to 650 Kg/Cum. conforming to IS2185(Part 3) in super structure above plinth level upto floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). 150.00 Cum. 7627.41 Rupees Seven Thousand Six Hundred Twenty Seven and Forty One Paise Only 1144111.50

18 Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design as specified and as directed by EIC. 2.00 Cum 2645.18 Rupees Two Thousand Six Hundred Forty Five and Eighteen Paise Only 5290.36

19 Providing and applying 18 mm cement plaster on brick/AAC/concrete surface in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge at any height and level including scaffolding, curing, etc. all complete as specified and as directed by EIC. 400.00 Sqm 491.63 Rupees Four Hundred Ninety One and Sixty Three Paise Only 196652.00

20 Providing and applying 15 mm thick cement plaster finished with a floating coat of neat cement of mix : 1:6 (1 cement: 6 fine sand) with neeru finish to concrete/AAC/ brick surfaces, in all positions and level including scaffolding, curing etc. complete as specified and as directed. 360.00 Sqm. 364.96 Rupees Three Hundred Sixty Four and Ninety Six Paise Only 131385.60

21 Providing and applying 6mm thick cement plaster on ceiling in cement mortar 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and neeru finsih all complete as specified and as directed by EIC. 430.00 Sqm 363.04 Rupees Three Hundred Sixty Three and Four Paise Only 156107.20

22 Providing & applying cement plaster 15 mm thick in cement mortar 1:4 (1 cement: 4 fine sand) to concrete/AAC/brick surfaces with floating coat of neat cement at any level and position including scaffolding,curing, etc. all complete as specified and as directed by EIC. 50.00 Sqm 437.40 Rupees Four Hundred Thirty Seven and Forty Paise Only 21870.00

23 Providing and applying 6mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge at bottom of chajja, slab projections and like at any height and level including scaffolding, curing, etc. all complete as specified and as directed by EIC. 15.00 Sqm. 274.99 Rupees Two Hundred Seventy Four and Ninety Nine Paise Only 4124.85

24 Providing and applying white cement based putty of 2 mm thickness over plastered surface of approved brand and manufacturer to prepare the surface even and smooth complete as diected by EIC. 800.00 Sqm. 179.30 Rupees One Hundred Seventy Nine and Thirty Paise Only 143440.00

25 Providing and applying two coats of acrylic emulsion paint on walls or ceiling of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour including priming coat with water thinnable cement primer having VOC content less than 50grams/litre all complete as specified and as diected by EIC. 800.00 Sqm. 193.49 Rupees One Hundred Ninety Three and Forty Nine Paise Only 154792.00

26 Providing and applying two coats of Acrylic Smooth exterior paint on walls of requierd shade and colour applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 kg/10 sqm all complete as specified and as diected by EIC. 400.00 Sqm 146.99 Rupees One Hundred Forty Six and Ninety Nine Paise Only 58796.00

27 Providing and applying two coats of synthetic enamel paint on walls/steel of approved colour to give even shade all complete as specified and as directed by EIC. 50.00 Sqm 94.09 Rupees Ninety Four and Nine Paise Only 4704.50

28 Providing and laying in position polished Granite stone Black, Cherry/ Ruby red or equivalent in flooring,steps,sills, etc. of required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 60.00 Sqm 4101.53 Rupees Four Thousand One Hundred One and Fifty Three Paise Only 246091.80

29 Providing edge moulding to 18 mm thick to granite including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 250.00 Rmt 467.65 Rupees Four Hundred Sixty Seven and Sixty Five Paise Only 116912.50

30 Providing and laying Vitrified tiles in floor in different sizes 9-10mm thick with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

a) Glazed Vitrified tiles Matt/Antiskid finish of size 600 x 600mm 50.00 Sqm 1340.72 Rupees One Thousand Three Hundred Forty and Seventy Two Paise Only 67036.00

b) Double charge vitrified tile of polish finish of size 600 x 1200mm 300.00 Sqm. 1443.50 Rupees One Thousand Four Hundred Forty Three and Fifty Paise Only 433050.00

31 Providing and laying Vitrified tiles in floor in different sizes 9-10mm thick with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, dado over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) , jointing with gray cement slurry @ 3.3 Kg/sqm including grouting the joint with cement & matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. 400.00 Sqm. 1485.51 Rupees One Thousand Four Hundred Eighty Five and Fifty One Paise Only 594204.00

32 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 100.00 Sqm 1018.41 Rupees One Thousand Eighteen and Forty One Paise Only 101841.00

33 Providing and fixing ISI marked 30mm flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including ISI marked Stainless Steel butt hinges with necessary SS screws all complete as specified and as directed by EIC. 50.00 Sqm 1988.03 Rupees One Thousand Nine Hundred Eighty Eight and Three Paise Only 99401.50

34 Providing & Fixing 1.0 mm thick decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish as approved with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality all complete as specified and as directed by EIC. 100.00 Sqm. 821.26 Rupees Eight Hundred Twenty One and Twenty Six Paise Only 82126.00

35 Providing and fixing bright finished brass door latch of size 300 x 16 x 5mm with necessary screws etc. all complete as specified and as directed. 52.00 Nos 294.90 Rupees Two Hundred Ninety Four and Ninety Paise Only 15334.80

36 Providing and fixing bright finished brass tower bolts (barrel type) of size 200 x 10mm with necessary SS screws etc. all complete as specified and as directed. 17.00 Nos 328.03 Rupees Three Hundred Twenty Eight and Three Paise Only 5576.51

37 Providing and fixing 125mm bright finished brass handles with screws etc. all complete as specified and as directed. 52.00 Nos 234.90 Rupees Two Hundred Thirty Four and Ninety Paise Only 12214.80

38 Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, screws etc. to suit shutter thickness all complete as specified and directed. 26.00 Nos. 248.45 Rupees Two Hundred Forty Eight and Forty Five Paise Only 6459.70

39 Providing and fixing stainless steel butt hinges (heavy weight) of size 100 x 60 x 2.50mm with necessary stainless steel screws etc. all complete as specified and as directed. 10.00 Nos 97.34 Rupees Ninety Seven and Thirty Four Paise Only 973.40

40 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight,mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately). Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

a) For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately). 370.00 Kg 547.88 Rupees Five Hundred Forty Seven and Eighty Eight Paise Only 202715.60

b) Providing and fixing fly proof wire gauze of Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides fixed in aluminium work of windows, clerestory windows and doors all complete as directed by EIC. 19.00 Sqm. 1037.49 Rupees One Thousand Thirty Seven and Forty Nine Paise Only 19712.31

c) Providing & fixing Window Lock as approved by EIC. 60.00 Nos. 55.13 Rupees Fifty Five and Thirteen Paise Only 3307.80

d) Providing & fixing of SS body with single nylon roller (weight bearing capacity to be 40kg) for sliding windows complete and as specified. 120.00 Each 63.16 Rupees Sixty Three and Sixteen Paise Only 7579.20

e) Providing & fixing Wool Pile for sliding window complete and as specified. 360.00 RM 20.14 Rupees Twenty and Fourteen Paise Only 7250.40

41 Providing and fixing with float glass of panes 5.0 mm thickness (weight not less than 12.50 Kgs/sqm) glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 50.00 Sqm 1377.69 Rupees One Thousand Three Hundred Seventy Seven and Sixty Nine Paise Only 68884.50

42 Providing and fixing M.S. grills of approved/required pattern in frames of windows, ventilators, etc. with M.S. flats, square or round bars, etc. including fixing to opening with holdfasts, screws,etc. including priming coat with approved steel primer all complete as specified and as directed. 650.00 Kg 218.16 Rupees Two Hundred Eighteen and Sixteen Paise Only 141804.00

43 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 145.00 Kg 706.95 Rupees Seven Hundred Six and Ninety Five Paise Only 102507.75

44 Providing and laying with average thickness of 120 mm and minimum thickness at khurra as 65 mm integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mmheight including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved byEngineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. 483.00 Sqm 630.52 Rupees Six Hundred Thirty and Fifty Two Paise Only 304541.16

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge.

45 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work , including cutting chases and making good the walls,etc.

(a) 15mm dia. 25.00 RM 455.62 Rupees Four Hundred Fifty Five and Sixty Two Paise Only 11390.50

(b) 20mm dia. 10.00 RM 492.05 Rupees Four Hundred Ninety Two and Five Paise Only 4920.50

(c) 25 mm dia. 75.00 RM 574.10 Rupees Five Hundred Seventy Four and Ten Paise Only 43057.50

(d) 32 mm dia. 40.00 RM 676.65 Rupees Six Hundred Seventy Six and Sixty Five Paise Only 27066.00

46 Providing and fixing gun metal valve of CI wheel of approved quality (screwed end) all complete as specified and as directed.

a) 25mm 4.00 Nos 569.66 Rupees Five Hundred Sixty Nine and Sixty Six Paise Only 2278.64

b) 32mm 4.00 Nos 631.16 Rupees Six Hundred Thirty One and Sixteen Paise Only 2524.64

47 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm standard size C.P. brass flush pipe, spreaders with unions and clamps with waste fitting as per IS : 2556 and cutting and making good the walls and floors wherever required all complete and as specified. 4.00 Each 7052.85 Rupees Seven Thousand Fifty Two and Eighty Five Paise Only 28211.40

48 Providing and fixing white vitreous china water closet squatting pan of size 580 x 440mm (Indian type-Orissa pattern) setting in position in lime concrete including providing and fixing ' P' or ' S ' traps, connecting to soil/ drainage pipe , providing and fixing 10 liters capacity PVC low level flushing cistern of approved shade including flushing pipe with manually controlled device handle (hnadle lever) conforming to IS:7231 with all fittings and fixtures making good walls and floor wherever required complete as specified and as directed. 2.00 Nos 6193.90 Rupees Six Thousand One Hundred Ninety Three and Ninety Paise Only 12387.80

49 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with same brand solid plastic seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required all complete as specified and as directed. 9.00 Each 5963.39 Rupees Five Thousand Nine Hundred Sixty Three and Thirty Nine Paise Only 53670.51

50 Providing and fixing white vitreous China Wash basin of size 550x400 mm with necessary brackets/anchor bolts including providing and fixing 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, including cutting and making good the walls wherever require complete as specified and as directed. 16.00 Nos 1719.95 Rupees One Thousand Seven Hundred Nineteen and Ninety Five Paise Only 27519.20

51 Providing and fixing 20mm nominal bore, 120mm long (weight not less than 198 gms) PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball all complete as specified and as directed. 2.00 Nos 235.77 Rupees Two Hundred Thirty Five and Seventy Seven Paise Only 471.54

52 Providing and fixing 15 mm nominal bore CP brass stop/angle cock of approved quality conforming to IS 8931 as spcified and as directed. 20.00 Nos 323.32 Rupees Three Hundred Twenty Three and Thirty Two Paise Only 6466.40

53 Providing and fixing 15mm nominal bore CP brass bib cock of approved quality confirming to IS:8931 as specified and as directed. (Weight not less than 400 gms.) 10.00 Nos 323.32 Rupees Three Hundred Twenty Three and Thirty Two Paise Only 3233.20

54 Providing and fixing 8mm dia CP/SS jet with flexible tube upto 1 meter long with SS triangular plate to EWC of approved brand and quality complete as specified and directed by EIC. 9.00 Each 319.57 Rupees Three Hundred Nineteen and Fifty Seven Paise Only 2876.13

55 Providing and fixing 15mm nominal bore and 300mm long unplasticised PVC connection with brass unions/nuts complete as directed. 8.00 Each 77.80 Rupees Seventy Seven and Eighty Paise Only 622.40

56 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

(a) 75mm dia. 20.00 RM 227.08 Rupees Two Hundred Twenty Seven and Eight Paise Only 4541.60

(b) 110mm dia. 70.00 RM 345.42 Rupees Three Hundred Forty Five and Forty Two Paise Only 24179.40

57 Providing and fixing in position approved and ISI brand PVC SWR drainage pipes in floors/ trenches or wall including connecting to drainage lines and sanitary wares, clamping with necessary fasteners or laying in trenches. The drainage lines are required to be tested for leakages all complete as specified and as directed. Earth work wherever required will be paid seperately.

a) 160mm dia. 20.00 RM 1835.57 Rupees One Thousand Eight Hundred Thirty Five and Fifty Seven Paise Only 36711.40

58 Providing and fixing in position approved and ISI brand PVC SWR fittings to drainage pipes as below:

i) 75mm 4.00 Nos 96.93 Rupees Ninety Six and Ninety Three Paise Only 387.72

ii) 110 mm 10.00 Nos 137.61 Rupees One Hundred Thirty Seven and Sixty One Paise Only 1376.10

b) Shoe plain Bends

i) 75mm 4.00 Nos 85.22 Rupees Eighty Five and Twenty Two Paise Only 340.88

ii) 110 mm 10.00 Nos 120.68 Rupees One Hundred Twenty and Sixty Eight Paise Only 1206.80

c) Single Tee with door

i) 75x75x75mm 2.00 Nos 150.29 Rupees One Hundred Fifty and Twenty Nine Paise Only 300.58

ii) 110 x110x110mm 10.00 Nos 214.31 Rupees Two Hundred Fourteen and Thirty One Paise Only 2143.10

d) Single Tee without door

i) 75x75x75mm 2.00 Nos 132.08 Rupees One Hundred Thirty Two and Eight Paise Only 264.16

ii) 110 x110x110mm 2.00 Nos 202.60 Rupees Two Hundred Two and Sixty Paise Only 405.20

59 Providing and fixing P.V.C. long arm Nahani Trap of 100mm diameter including SS grating, bend and connecting piece upto the outside face of the walls making good damaged surface, testing etc. complete as directed by Engineer in charge. 10.00 Nos 99.81 Rupees Ninety Nine and Eighty One Paise Only 998.10

60 Providing and fixing PVC (SWR) cowl cap 75mm dia. with necessary fixing arrangement as directed. 4.00 Nos 23.55 Rupees Twenty Three and Fifty Five Paise Only 94.20

61 Providing and fixing 18mm thick Pre-laminated medium density fibre board with decorative lamination on one side and balancing lamination on one side Grade - I (exterior grade) confirming to IS:14587 fixed to steel/wooden framework for preparation of shelves, benches, tables, cubboard, chairs, other furnitures, etc with screws/nut bolts having oval head and fittings, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand all complete as directed by EIC. 10.00 Sqm 1295.73 Rupees One Thousand Two Hundred Ninety Five and Seventy Three Paise Only 12957.30

62 Providing and fixing mild steel tubes joints mitred and welded including fixing applying a priming coat of approved steel primer and two coat of synthetic enamel paint for steel framework for preperation of shelves, benches, tables etc all complete as per the direction of Engineer-In-charge. 500.00 Kg 162.22 Rupees One Hundred Sixty Two and Twenty Two Paise Only 81110.00

63 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern 120.00 Sqm. 999.00 Rupees Nine Hundred Ninety Nine Only 119880.00

64 Supply and fixing of acrylic name board (double layer) on brick/concrete surface with pasting acrylic letters/alphabets/symbols/layer of 3mm thick with suitable adhesive over transparent acrylic sheet/layer of 4mm thick drilled with screws, etc. in line,level, at all height/position all complete as directed.Note: Alphabets may be in Hindi/English/Marathi as per direction of EIC. 4.00 Sqm. 4734.41 Rupees Four Thousand Seven Hundred Thirty Four and Forty One Paise Only 18937.64

65 Supply and fixing acrylic letters/alphabets/symbols of 3mm thick and UV printed HAL logo pasting with suitable adhesive/self adhesive over ACP panel 3mm thick supported over MS hollow sections of size 25mm x25mm x 2.6mm thick in proper line, level, at all height,positions including transportation, etc.all complete as diretced. Note: Alphabets may be in Hindi/English/Marathi as per direction of EIC. 5.00 Sqm. 6509.81 Rupees Six Thousand Five Hundred Nine and Eighty One Paise Only 32549.05

66 Supply and fixing name board of 3 mm acrylic transparent board with radium background along with radium letters for room nomenclature all complete as directed. Note: Alphabets may be in Hindi/English/Marathi as per direction of EIC. 2.00 Sqm. 4734.41 Rupees Four Thousand Seven Hundred Thirty Four and Forty One Paise Only 9468.82

67 Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge. 10.00 Sqm. 2820.77 Rupees Two Thousand Eight Hundred Twenty and Seventy Seven Paise Only 28207.70

68 Writing Letters --- Writing letters or figures ( Block, Roman, Italic or Indian) not exceeding 30 cm high of approved colour, shade & fashion complete all as specified & as directed by EIC. (Letters etc., shall be painted with thick paint, so that they stand out boldly and solidly without showing signs of brush marks, if necessary, they shall be repainted until the desired result is obtained.) 300.00 Each 5.63 Rupees Five and Sixty Three Paise Only 1689.00

69 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank all complete as specified and as directed. 6000.00 Litre 10.07 Rupees Ten and Seven Paise Only 60420.00

Part B : Electrical

1 Supply And Installation Of SPN 12 Way, Double Door, Distribution Board (D.B.) Make: Siemens / L & T / ABB / C&S 3.00 NOS 2118.82 Rupees Two Thousand One Hundred Eighteen and Eighty Two Paise Only 6356.46

2 Supply And Installation Of 63 Amp., DP MCB, Breaking Capacity 10KA, Make: Siemens / L & T / ABB / C&S/ Legrand 3.00 NOS 482.34 Rupees Four Hundred Eighty Two and Thirty Four Paise Only 1447.02

3 Supply And Installation Of 6 A To 32 Amp.,Breaking Capacity 10KA, SP MCB Make: Siemens / L & T / ABB / C&S/ Legrand 30.00 NOS 234.31 Rupees Two Hundred Thirty Four and Thirty One Paise Only 7029.30

4 Supply And Installation Of 16 Amp., DP MCB, Breaking Capacity 10KA, for control at each class room / office / toilet / hall etc. Make: Siemens / L & T / ABB / C&S/ Legrand 28.00 NOS 600.41 Rupees Six Hundred and Forty One Paise Only 16811.48

5 Supply of materials & carry out point wiring (for fans, lights, etc.) using “HAVELLS / ANCHOR / FINOLEX / POLYCAB / TORRENT” make 1.5 Sq.mm. stranded copper conductor, PVC insulated wire & 1.0 Sq.mm copper earth wire, “PRECISION / MODI / FINOLEX / POLYCAB / PRESSFIT” make PVC conduit / casing capping, “ANCHOR / M.K / LEON/ L & T " make 6A modular switch, socket, modulr metal flush box, modular surface plate, ceiling roses etc. Note: 1) Measurement shall be “point wiring” wise and one switch controlling one point shall be counted as one point. 2) Switch & socket installed on same board will be treated as half point. (3) This is a conceal-wiring work. 252.00 NOS 1342.68 Rupees One Thousand Three Hundred Forty Two and Sixty Eight Paise Only 338355.36

6 Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FR is PVC insulated copper conductor, single core cable in surface/ recessed as required. 2x2.5 sq. mm + 1x1.5 sq. mm earth wire. Wire / Cable Make: HAVELLS / ANCHOR / FINOLEX / POLYCAB / TORRENT 460.00 M 251.70 Rupees Two Hundred Fifty One and Seventy Paise Only 115782.00

7 Supply of materials & carry out point wiring using HAVELLS / ANCHOR / FINOLEX / POLYCAB / TORRENT make 2.5 Sq.mm. copper conductor, PVC insulated wire & 1.5 Sq.mm copper earth wire, PRECISION / MODI / FINOLEX / POLYCAB / PRESSFIT make PVC conduit / casing capping, ANCHOR / M.K. / LEON / L & T make 16A, 3 module, modular switch, socket, modular metal flush box, modular surface plate etc. Note: 1) Measurement shall be “point wiring” wise. 48.00 NOS 1665.77 Rupees One Thousand Six Hundred Sixty Five and Seventy Seven Paise Only 79956.96

8 Supply and installation of modular stepped type , socket size, electronic fan regulator 230V, Flush type. Make: ANCHOR / M.K. / LEON/ L& T/COLORS 52.00 NOS 337.73 Rupees Three Hundred Thirty Seven and Seventy Three Paise Only 17561.96

9 Supply & Laying Of XLPE Insulated,Armoured Heavy Duty Electric Cable With Aluminium Conductor, 1100 V Grade, 4 Core X Cross Sectio Area 50 Sq.Mm. (Execution as per site requirement.) Make: Finolex/ RR Cables/ Havells/ Polycab 230.00 M 198.62 Rupees One Hundred Ninety Eight and Sixty Two Paise Only 45682.60

10 Supply & Laying Of XLPE Insulated,Armoured Heavy Duty Electric Cable With Aluminium Conductor, 1100 V Grade, 4 Core X Cross Sectio Area 10 Sq.Mm. (Execution as per site requirement.) Make: Finolex/ RR Cables/ Havells/ Polycab 360.00 M 183.06 Rupees One Hundred Eighty Three and Six Paise Only 65901.60

11 Supply of 1200 mm. Sweep ceiling fan , colour- white / Ivory of make HAVELLS / KHAITAN / USHA / ORIENT / CROMPTON / BAJAJ with all accessories & carryout out installation. 52.00 NOS 2498.65 Rupees Two Thousand Four Hundred Ninety Eight and Sixty Five Paise Only 129929.80

12 Supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp. On pole or wall with the help of necessary fixtures. Make: Bajaj/ Crompton / Havells / Philips / Syska. 5.00 NOS 2800.00 Rupees Two Thousand Eight Hundred Only 14000.00

13 Supply and installation of LED street light fitting, approximately 70 W, with all fixing material like screws, clips etc. 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket / bend pipe with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. Make: Bajaj/ Crompton / Havells / Philips / Syska. 5.00 NOS 2500.00 Rupees Two Thousand Five Hundred Only 12500.00

14 Supply and installation of LED batten, 22 W / 24 W, with all fixing material like screws, clips etc. Make: Bajaj/ Crompton / Havells / Philips / Syska. 140.00 NOS 200.00 Rupees Two Hundred Only 28000.00

15 Supply and installation 20 Amps SPN MCB metallic Plug & Socket. Make: Crompton/ Anchor / Havells/ Standard / C&S 3.00 NOS 1069.94 Rupees One Thousand Sixty Nine and Ninety Four Paise Only 3209.82

16 Cutting chase, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed conduit wiring, etc., and making good, cutting not exc. 10 girth. 570.00 M 75.00 Rupees Seventy Five Only 42750.00

17 Earthing complete with GI earth plate electrode 600mm×600mm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia / earthing strip by means of bolts, nuts, check nuts and washers of galvanised iron or steel. providing masonry enclosure with cover plate. Having watering pipe arrangement. With bentonite powder or mixture of salt and charcoal/coke. 4.00 NOS 6838.78 Rupees Six Thousand Eight Hundred Thirty Eight and Seventy Eight Paise Only 27355.12

18 Supply and installation of TPN 4 Way, Double Door, MCB Distribution Board (D.B.). Make: Siemens / L & T / ABB / C&S / Legrand 3.00 NOS 6875.39 Rupees Six Thousand Eight Hundred Seventy Five and Thirty Nine Paise Only 20626.17

19 Supply and installation of 63 Amp., 4P MCB. Make: Siemens / L & T / ABB / C&S/ Legrand 3.00 NOS 2877.56 Rupees Two Thousand Eight Hundred Seventy Seven and Fifty Six Paise Only 8632.68

20 Supply and fixing LED Solar street light fitting 16 Watt including galvanized steel pole in built, lithium ion battery, solar panel, charge controller with dusk down sensor complete. (Excavation & earth work shall be measured separately) Make of Batteries : TATA / EXIDE / AMARON / SF SONIC / MICROTEK / EMCO 4.00 NOS 22000.00 Rupees Twenty Two Thousand Only 88000.00

21 Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. Make: Bajaj/ Crompton / Havells / Philips / Syska. 16.00 NOS 2150.00 Rupees Two Thousand One Hundred Fifty Only 34400.00

22 Supply and installation of Switch Fuse Unit (SFU) with sheet steel enclosure 500 V, 3 phase with HRC fuses complete with Neutral link of capacity 125 Amps. (Suitable for external / wall mounting.) Make: SIEMENS / STANDARD / C&S / L&T 2.00 Nos 4714.48 Rupees Four Thousand Seven Hundred Fourteen and Forty Eight Paise Only 9428.96

23 Non clog vertical / horizontal submersible pumps with chrome steel impeller and cutter, non-clog to pass 40 mm size particles including Supply, installation with guide rail and lifting chain, cables, Earthing, testing complete with 2 years maintenance. 2 HP Make: LUBI / LAXMI / TAXMO / CROMPTON 1.00 NOS 10000.00 Rupees Ten Thousand Only 10000.00

Sub-Total (Excluding GST) Rupees One Crore Thirty Lakh Eighty Six Thousand Three Hundred Thirty Six and Fifty One Paise Only 13,086,336.51

The Tenderer has to Quote Percentage Above / Below as Specified and Percentage Shall be Quoted in Figures. Approximate Basic Amount Put to Tender Select Above or Below Percentage in Figures [Excluding GST] Amount

Tenderer's Quote (Excluding GST) 13086336.51 BELOW % 13,086,336.51

Add 18% GST Rupees Twenty Three Lakh Fifty Five Thousand Five Hundred Forty and Fifty Seven Paise Only 2,355,540.57

Grand Total (Including GST) Rupees One Crore Fifty Four Lakh Forty One Thousand Eight Hundred Seventy Seven and Eight Paise Only 15,441,877.08

Note: (i) The tenderer has to quote percentage above / below against the total amount considering the specified standard rates. If the contractor does not quote any percentage above / below on the total amount, the tender shall be treated as invalid and will not be considered. (ii) The quoted rates in the bill of quantities are inclusive of all types of taxes, duties levies, fees and charges etc., imposed by Central/ State Govt. and local bodies Compensation Cess, Labour Cess (if any), Custom Duty, royalties and other levies. It shall also include all other costs including loading, un-loading, insurance, transportation, testing and Certification expenses except GST . GST at the prevailing percentage is added in the BOQ at the end.

WARNING: PLEASE ENTER PERCENTAGE QUOTE

HINDUSTAN AERONAUTICS LIMITED

AIRCRAFT OVERHAUL DIVISION, NASHIK

Pre-Qualification Profile

Tender Ref No. or Contract No.: NK/FW/CSR-1596/2024-25

Name of Work: CONSTRUCTION OF PHC BUILDING AT JANORI VILLAGE, TALUKA DINDORI, DISTRICT NASHIK UNDER CSR 2024-25

Estimated Amount in Rs. Lakhs: 154.42

Tender Notice no.: NK/FW/534/2024-25

Name of the Individual / Firm / Company: * Mandatory

Sl.No Description Details Remarks

1.0 Essential/ Prequalification Criteria

1.1 Annual Turnover: Average annual financial turn over during the last 3 years (Financial Year), ending 31st March 2023 of the previous financial year /Accounting year [ should not be less than 30% of Amount put to tender] i.e Rs. In Lakhs 46.33

Financial YEAR Turn over (Rs. In Lakhs) Remarks

2018-19 Audited copies and Audit report by CA with UDIN of financial documents for last five (5) years Viz.Balance sheet, P &L account, Supporting Schedules and notes to account.

Average Annual Turnover of last Three Financial Years Rs. 0.00 Not meeting eligible criteria

1.2 Solvency : Latest Bankers Solvency Certificate from Nationalized/ scheduled Bank issued NOT before 12 months from the last date of tender Submission.( Should not be less than 40% of the estimated cost i.e Rs. In Lakhs) 61.77

Name of Bank & Branch Issued Related Document to be Uploaded to eProcurement Portal.

Date of Issue [DD-MM-YYYY]:

Value (Rs. In Lakhs) Not meeting eligible criteria

1.3 Experience:

Experience of having successfully completed similar works (As per "Work Details" table of Etender notice.) during last 7 years ending last day of previous month. [Latest work experience certificate may be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost. OR (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost. OR (iii) ONE similar completed work each costing not less than the amount equal to 80% of Amount put to the tender.

Completed similar works during last 7 years You are Not Eligible

Work No I Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal.

Brief Description of Work:

Completed value of Work in `Lakh:

Date of Commencement of Work [DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

You are Not Eligible

Work No II Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal.

Brief Description of Work:

Completed value of Work in `Lakh:

Date of Commencement of Work [DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

Work No III Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal.

Brief Description of Work:

Completed value of Work in `Lakh:

Date of Commencement of Work [DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

1.4 GSTIN Registration Number. Registration certificate to be uploaded

1.5 ESIC Registration Number Registration certificate to be uploaded

1.6 EPF Registration Number Registration certificate to be uploaded

1.7 Bid Capacity ( 2AN-B)

b) Value of the work executed in last five Financial years (Financial year wise) Values (Rs. in Lacs) (Required for bid capacity calculation)

2018-19 Related documents to be uploaded in eprocurement portal.

A = maximum value of works executed in any one year during last five years of which will be brought to current price level by applying a weightage of 10 % per year. Value of works executed during last five years shall be certified by Chartered Accountant and shall be considered for evaluation.

c) B = value at current price level of existing commitment and ongoing works to be completed in the next ‘N’ years (i.e 10 Months). (Authority:- Ministry of Statistics & Programme Implementation Guidelines Vide DO No 11025/28/2001 Dt. 7-11-01, Standard General Conditions for Domestic Contracts, as per Clause 4.6) Balance Value of the existing commitments and on-going works (Works in hand/in progress) to be completed in the next ten (10) months. Related documents to be uploaded in eprocurement portal.

Not meeting eligible criteria

1.8 Earnest Money Deposit (EMD) Related document to be scanned and uploaded to e-procurement portal and original one to be submitted to the address mentioned in NIT

1.9 License for execution of Electrical works and other specialized works from the concerned authorities /organizations/bodies (applicable for Electrical works combined with Civil works) Related Document to be Uploaded to e-procurement portal. i.e License or udertaking

2.1 Documents to be uploaded along with tender

2.1.1 Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, etc., Related Document to be Uploaded to eProcurement Portal.

Type of ownership

If Other, please specify

2.1.2 Address for correspondence:

2.1.3 Contact details

Contact person name

Ph. No. with STD code

FAX No. with STD code

2.1.5 I.T Returns for past 03 years (Assesment Year)

2021-22 Related documents to be uploaded in eprocurement portal.

2.1.6 Bank Balance statement for last three months. Related documents to be uploaded in eprocurement portal.

2.1.7 Details of latest overdraft facilities available with the agencies. Related documents to be uploaded in eprocurement portal.

2.1.8 Details of plant & machinery for the work. Related documents to be uploaded in eprocurement portal.

2.1.9 Proposed work completion schedule in the form of bar- chart. Related documents to be uploaded in eprocurement portal.

2.1.10 Details of person holding the power of Attorney.

Name Related documents to be uploaded in eprocurement portal.

Ph. No. with STD code

2.1.11 Bank(s) details: [Copy of the cheque leaf to be uploaded]

Bank Account No. ECS Bank details as per Form No E-05 in tender documents , signed and sealed by concerned bank to be Uploaded to eProcurement Portal. And hard copy of original ECS and cancelled cheque to be submitted to address mentioned in e-tender notice for refund of EMD or payment etc(New bidder).

Name of the Bank

Type of Account

3.0 Acceptance by party for Scope of work as per BOQ and Tender terms & conditions Accepted

4.0 DECLARATION

a The document being viewed / downloaded from the website and having read & understood all the contents of the tender document mentioned under terms and conditions ( Page 1 to 146) including price bid do hereby accept all the terms and conditions laid down Accepted

b I/We declare and confirm that - 1. All information and attachments submitted along with this offer are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my offer . 3. I/We shall not make refund claims of expenditure incurred in processing this offer. 4. I / We aware that document sought only be uploaded for evaluation of offer. Accepted