Construction of Natural Science Museum In State Museum Campus At Dist.- Lucknow (Balance work)

Amount

Civil work

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) i/c all material labour & T&P

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 50 mm thick

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class-150 in superstructure above plinth level up to floor V level. 1:4 (1 cement : 4 coarse sand)(Labour Only)

Brick work with common burnt clay F.P.S. (non modular) bricks of class-150 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) (Labour Only)

Thermo-Mechanically Treated bars of grade Fe-500D or more work such as in reinforced concreted or reinforced brick work (when not included in overall rates) wrought to required shape as necessary including bending for proper completion of the work (Labour Only)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)Powder coated aluminium (minimum thickness of powder coating 50 micron)

Sanitary Work

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing white vitreous china white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I.brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls where required :White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : Range of ONE urinal basins with 5 litre white P.V.C. automatic flushing cistern

Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern

Range of four urinal basins with 10 litre white P.V.C. automatic flushing cistern

Providing & fixing stone slab table rubbed, edges rounded and polished of size 75 X 50cm deep and 1.8 cm thick fixed in urinal patitions by cutting chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregste 6mm nominal size) as per Engineer-in-charge and finished smooth Granite stone of approved shade

Providing and fixing Salem Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with CI brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. Kitchen sink with drain board 510x1040 mm bowl depth 200 mm

Kitchen sink without drain board610X510 mm bowl depth 200mm.

Providing & fixing PVC waste pipe for sink oncluding PVC waste fitting Complete Flexible Pipe 32mm Dia

40mm Dia

Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing toilet paper holder :C.P. brass

Providing and fixing soil, waste, vent pipes 'Rigid PVC pipe SWR'110mm dia

160 mm dia

Providing & fixing PVC clamp'PVC rigid SWR 110mm

PVC rigid SWR 160mm

Providing and fixing bend of required degree with access door, bend complete.'PVC rigid SWR 110mm

PVC rigid SWR 160mm

Providing and fixing bend of required degreePlain bend complete.'PVC rigid SWR 110mm

PVC rigid SWR 160mm

Providing and fixing PLAIN TEE of required degree 'PVC rigid SWR 110mm

PVC rigid SWR 160mm

Providing and fixing Door TEE of required degree 'PVC rigid SWR 110mm

PVC rigid SWR 160mm

Providing and fixing PVC cowel'PVC rigid SWR 110mm

Providing and fixing collar.'PVC rigid SWR 110mm

PVC rigid SWR 160mm

Providing and fixing of PVC Ntrap including all material labour complete.'PVC rigid SWR 110mm

Providing and fixing of PVC Ntrap including all material labour complete.'PVC rigid SWR 110mm

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms.

Providing and fixing PTMT towel rail complete with brackets fixed wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVCplain & brass threaded fittings This includes jointing of pipes & fittingswith one step CPVCsolvent cement, trenching, refilling & testing joints complete as per direction of Engineer in Charge. - Exposed on wall15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

32 mm dia. nominal bore

Same as above but Concealed work, including cutting chases and making good the walls etc.15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

32 mm dia. nominal bore

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. External work40 mm dia, nominal bore

50 mm dia, nominal bore

65 mm dia, nominal bore

80 mm dia, nominal bore

Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends) 25mm dia, nominal bore

32 mm dia, nominal bore

40 mm dia, nominal bore

50 mm dia, nominal bore

65 mm dia, nominal bore

80 mm dia, nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet 100 mm diameter

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work 40 mm dia, nominal bore

50 mm dia, nominal bore

65 mm dia, nominal bore

80 mm dia, nominal bore

Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931-15mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore. 15 mm nominal bore

Providing and fixing grating of approved quality and colour Circular type100 mm nominal dia

Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layers by ramming, watering etc. stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50m :Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round R.C.C. pipes including bed concrete as per standard design : '150 mm diameter pipe

200 mm diameter pipe

Providing and laying PVC PIPEwith 6 kg pressure ,jointing of pipe and testing complete as per desiser of engineer in charge.'160 mm dia PVCpipe

200 mm dia PVC pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With F.P.S. bricks with class designation 150

Less for C.I. Cover wherever not fixed

c/o manhole of internal size 600x600 mm average depth upto 600 mm complete with b/w, plaster, making channel& RCC manhole cover

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) :With F.P.S. bricks class designation 150

Less for C.I. Cover wherever not fixed

Guard Room

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge:

Filling By carted earth in trenches, plinth, sides of foundation, campus etc. in layers not exceeding 20 cms in depth, consolidating each deposited layer by ramming and watering including lead upto 50 m & lift upto 1.50 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. Under floor

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and excluding reinforcement -(a) 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) All work up to plinth level :

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases , excluding the cost of centering, shuttering, finishing and excluding reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size). All work above plinth level up to floor five level

Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Brick work with common burnt clay F.P.S. (non modular) bricks of class-150 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class-150 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing and injecting chemical emulsion for preconstructional antitermite treatment and creating a chemical barrier under and alround the coloumn pitswall tench basement excavation top surface if plinth filling junction of wall and floor along the external perimer of binding expansion joints,surrounding of pipes and conduits etc.complete(plinth area of the building at ground floor only shall be measured as per I.S.6313(Part ll 1981) aldrine emulsifiable concrete or any other approved material such as hepthachlor or chlordance will be used.The rate of application of chemical emulsion shall be as follows:- (1)treatment for masonary & foundation 5 litres per sq.m. (2)back fill in immediate contract with foundation 7.5 litre per sq.m (3)treatment of top surface of plinth filling 5 liters per sq.m. (4)treatment of soil along external parameter of building 7.50 lire per sqm. (For payment plinth area to be measured as per IS Code).

Thermo-Mechanically Treated bars of grade Fe-500D or more work such as in reinforced concreted or reinforced brick work (when not included in overall rates) wrought to required shape as necessary including straightening, cutting, bending, placing in position and binding for proper completion of the work and including supply of steel & binding wire and its wastage.

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete size 250x16 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125 mm

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with 4.0 mm thick glass panes

Supply and fixing of flush doors commercial quality conforming to IS : 2202 (Part I-1983) including fixing of wooden cleats and stoppers and including fixing and adjustment of hinges bolts locks handle springs fitting with necessary screw to be supplied departmentally.30 mm thick single leaf shutters

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness .The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady] the frame.

30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames

15 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) in single coat on rough side of single or half brick wall.

12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) in single coat on smooth side of single or half brick wall.

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) In ceiling

15 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) in single coat on rough side of single or half brick wall. In plinth.

Add for plaster drip course in plastered surface or moulding to R.C.C. projections

40 mm thick cement concrete flooring with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by approved make & colours), of 1st quality conforming to IS : 15622, of approved make, in colours & shade, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Supply and fixing 6 mm thick china white glazed tiles in flooring or in skirting or dado laid with 1:3 cement and approoved course sand mortar finished with white cement slurry jointing and polishing complete including supply of all material and tools and plant etc. required for proper completion of the work.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 18 mm thick

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 35 mm wide and 3.15 mm thick

Distempering (two coat) with dry distemper of approved brand and manufacture and of required shade on undecorated wall surface to give an even shade over and including a priming coat with cement primer of approved brand and manufacture such as Berger, J&N Shalimar, Asian Paints after thoroughly brushing the sufface free from mortar dropping and other forein matter and also including prepairing the surface even with Plaster of Paris or approved synthetic material and sand papered smooth including cost of all material.

Finishing wall with water proofing cement paint (Two coat) of approved make such as super snowcem, Durrocem, fobiacem, guttucem, supercem quality and of required shade on undecorated wall surface over including one coat white cement primer to give an even shade after thoroughly brushing the surface to powdered materials including curing and cost of all materials.

Painting two coats over priming coat on steel & other metal surfaces up to 10 cm width or sq,mt in areas with superior synthetic enamel such as Luxol-3 Hi-gloss apcolite superlac, Dulux specified finishing to give an even shade & incl. cleaning the surface of all dirt, dust & other foreighn matter sand preparing and knotting incl. cost of all etc. required for proper completion of work.

Painting two coats over priming coat on wood surfaces up to 10 cm width or sq,mt in areas with superior synthetic enamel such as Luxol-3 Hi-gloss apcolite superlac, Dulux specified finishing to give an even shade & incl. cleaning the surface of all dirt, dust & other foreighn matter sand preparing and knotting incl. cost of all etc. required for proper completion of work.

Underground Tank 100 KL (Details Attached)

16 Passenger Lift (G+2)

Supply of Hoist Beam : 100 kg/m x (SOR PWD Item 503)

Add Extra for Supply of Trap Door : 50 kg/sqm x (SOR PWD Item 503)

Cable etc.

Supplying and laying of aluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm bellow ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top .On surface the cable run shall be fixed on MS clamps etc.of suitable size or as directed by the Engineer-Incharge ,complete in all respect.The armouring of the cable shall be properly connected with the earth conductor by clamps etc.Following size size 35 sq mm x 3-1/2core

size 50 sq mm x 3-1/2core

Supply and fixing of brass nickle plated compression gland for pvc insulated & armoured served sheaththed ,underground cable including rubber ring etc. complete in all respect. Thearmouring of the cable shall be properly connected with the earth as per direction of engineer -incharge.for cable size 35 sq mm x 3-1/2core

size 50 sq mm x 3-1/2core

Supply and fixing of plain or pin type copper tin plated cable socket (lug) to cable leads for pvc insulated & armoured cable insulating with tape and making connection. complete in all respect as per direction of engineer -incharge. for cable size 35 sq mm

size 50 sq mm

S&F of 63 Amp. 415 V metal clad T.P.N. rewireable type switch fuse unit on angle iron bracket complete in all respect. CAT B

Supply and fixing of flush/surface mounting 8 ways SPN distribution boards (Legrand Lexic) without MCB with additional metal door complete in all respects. As directed by engineer incharge. CAT A

Supply & fixing and making connection of 63 amp. 100mA ELCB/ RCCB of Din Rail mounting in complete in all respect as per direction and satisfaction to the Engineer in Charge.

Electrical Labour works

Labour Charges For Wiring point for light with 1.5 Sq. mm FR PVC insulated multistrand single core copper conductor cable in PVC conduit with 1.5 Sq. mm FRLSH PVC insuleted multistrand copper conductor cable as earth wire drawn inside. continuity wire, Modular type switch & ceiling rose/angle/ batten holder on 3mm thick phenolic laminated backelite sheet etc. complete in all respect. with Modular Box & Cover plate.

Do as above Item But 2 way Light Point

Do as above Item But Fan/Fresh air Fan Point

Do as above Item But Plug Point

Do as above Item But Call Bell Point

Labour Charges For Laying of submains with two number 4 sq.mm FRLSH PVC insulated 1100 Volt grade multistrand single core copper conductor cable in 20 mm dia heavy duty (2 mm thick) PVC conduit with one no. 2.5 sq.mm FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit. complete in all respect.

Labour Charges For Laying of submains with two number 6 sq.mm FRLSH PVC insulated 1100 Volt grade multistrand single core aluminium conductor cable in 25 mm dia heavy duty (2 mm thick) PVC conduit with one no. 4 sq.mm FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit. complete in all respect.

Labour Charges For Laying of submains with 4 number 6 sq.mm FRLSH PVC insulated 1100 Volt grade multistrand single core copper conductor cable in 32 mm dia heavy duty (2 mm thick) PVC conduit with 2 nos. 4 sq.mm FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit. complete in all respect.

Labour Charges For Laying of submains with 4 number 10 sq.mm FRLSH PVC insulated 1100 Volt grade multistrand single core copper conductor cable with heavy duty (2 mm thick) PVC conduit & 2 nos. 6 sq.mm FRLSH PVC insulated copper conductor cable as earth continuity wire for drawn in conduit. complete in all respect.

Labour Charges For Fixing of 200 Amp. four pole change over switch on 50mm x 50mm x 6mm angle iron frame, painting and other material required for proper completion of the work.

Labour Charges For Fixing of single light wall bracket on matching M.D.F.E.G. Board base etc. complete in all respect. Cat.-AAA

Labour Charges For Laying of Aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.16 sqmm x 4 core.

35 sqmm x 3½ core.

70 sq.mm x 3½ core.

120 sq.mm x 3½ core.

400 sq.mm x 3½ core.

Labour Charges For Laying of 25 mm x 3 mm G.I. Strip from earth electrode directly in the ground as required complete in all respect.

Labour Charges For Burring of Safe Earthing Electrode T-19, (Hot Dip Galvanized), Length up to 3000 mm, Outer Dia 50 mm, inner Dia 25, terminal Dia 12 mm, outer G.I. pipe of 16 swg and inner G.I. pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity and one earthing lead of 25 mm x 3mm G.I. strip upto switch board (from apron to switch board, the cost of G.I. strip will be extra) along with 30 cm square C.I. frame with hinged cover & masonry housing.

Labour Charges For Errection of factory fabricated and wired metal clad dust and vermin proof floor mounting M.S. Channel Base with bottom and top cable entreis Electrical control panel with TPN MCCB's (Four pole 36 KA with thermal magnatic release) switches complete in all respect with Plinth as per below specification. Indoor Type (For Power) Incoming- 200 Amp MCCB = 1 No. Outgoing- 63 Amp MCCB = 6 Nos.

(For Light & Lift) Incoming - 200 Amp MCCB = 1 No. Outgoing - 100 Amp MCCB = 2 Nos. 63 Amp MCCB = 2 No.

(For A.C. Outdoor Type) Incoming - 200 Amp MCCB = 1 No. Outgoing - 63 Amp MCCB = 6 Nos.

Labour Charges For Errection of factory fabricated and wired metal clad dust and vermin proof floor mounting M.S. Channel Base with bottom and top cable entreis Electrical control panel with TPN ACB (Four pole65 KA with thermal magnatic release) switches complete in all respect with Plinth as per below specification. (Out Door Type) Incoming - 800 Amp ACB = 1 No. Outgoing - 200 Amp MCCB = 6 Nos.

Labour Charges For Fixing of 6 Amp. To 32 Amp. SPMCB (10 KA) Cat-A

Labour Charges For Fixing of 40 Amp. SP MCB (10 KA) Cat - A

Labour Charges For Fixing of 40Amp. DP MCB (10 KA) Cat.-A

Labour Charges For Fixing of 63 Amp. TP MCB (10 KA) Cat-A

Labour Charges For Fixing of 40 Amp 4 pole MCB - (10KA) Cat-A

Labour Charges For Fixing of 63 Amp 4 pole MCB - (10KA) Cat-A

Labour Charges For Fixing of 80 Amp. To 100 Amp. 4 pole MCCB (16 KA) Thermal Magnetic release. Cat-A

Labour Charges For Fixing of surface/flush mounting 8 ways SPN distribution board with additional metal door without MCB complete in all respect, as directed by Engineer in charge. Cat-A

Labour Charges For Fixing of surface/Flush mounting 4 ways TPN distribution board with additional metal door without MCB complete in all respect, as directed at site by Engineer in charge. Cat.-A

Labour Charges For Fixing of surface/flush mounting 8 ways V TPN distribution board with addition metal board without MCB complete in all respect. as directed at site by Engineer in chardge. Cat-A

Labour Charges For Fixing of surface/flush mounting 8 ways V TPN distribution board with addition metal door without DPX3 160 MCCB complete in all respect. as directed at site by Engineer in chardge. Cat-A

Labour Charges For Fixing of call bell of approved make on polished MDFEG/ Teak ply board including making connections etc. complete in all respect.

Labour Charges For Erection and testing of ceiling fan and regulator etc. excluding supply of down rod, complete in all respect.

Labour Charges For Erection and testing of exhaust fan on the existing hole with suitable size of rag bolts, nuts and washers etc. complete in all respect.

Labour Charges For Fixing of 16 gauge M.S. drum duly painted including making hole in the wall for exhaust fan and finishing properly complete in all respect.

Labour Charges For Fixing of Fire extinguisher, ABC Type 6.00 Kg. capacity (ISI marked IS: 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Labour Charges For Fixing of Co2 type Fire extinguisher, 4.5 Kg. capacity (ISI marked IS: 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Labour Charges For Fixing of fire bucket, round bottom made of G.I. Sheet 9-11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chined and locked, initially filled with fine river sand, water as per directions of Engineer-in-charge.

Labour Charges For Fixing of shock treatment chart (Prescribed under I.E Rule) duly framed with glass and supported from back with hard board or soft board with supply of all material labour T&P for proper completion of work.

Labour Charges For Fixing of 1800 mm x 900 mm x 12 mm thick chequered rubber matting of tested quality.

Labour Charges For Fixing of Power plug with 20A/250 volt flush type modular switch and 5 pin 20A/250V flush type universal modular socket switch on concealed M.S. box including supply of all material, labour T&P etc. required for completion of work.

Labour Charges For Fixing of hexagonal/Round G.P. fan box of approved make made up 1.0 mm thick ISI Marked G.P. sheet spot welded four to Eight holes of 25.4 mm for pipe entry of the box. Holes should be semi-shuttered type with 0.5 mm G.P. sheet made upper & lower cover duly screwed fitted with 300 mm round zink coted M.S. bar x 12 mm & brand name should be embossed. Fixing with wiring conduit laid in the R.C.C. roof before concreting along with supply of all material, labour, T&P etc. required for proper completion of work.

Labour Charges For Fixing of Electronic fan regulator(Modular) 120-280 V. ISI marked, on the existing switch board including making connections, required material, labour T&P etc. for proper copmletion of work to the satisfaction of Engineer in charge of work.

Labour Charges For Laying of submain with two number 2.5 sq.mm FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy duty (2mm thick) PVC conduit with 1 nos. 1.5 sq.mm FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable as earth continuity wire drawn inside the conduite complete in all respect.

Labour Charges For Laying of submain with two number 1.5 sq.mm FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy duty (2mm thick) PVC conduit with 1 nos. 1.5 sq.mm FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable as earth continuity wire drawn inside the conduite complete in all respect including matching colour wash.

Labour Charges For Fixing of recess/Surface mounting round 18 watt to 20 watt Cut out Min 150mm, Height Min 40mm, LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/Reflector and driver set, suitable for 24Hr Continuous Operation, complete in all respect. 1800-2000 system lumens, 1001m/watt, PF>0.95, THD<10%, at full load CRI>80, with 3 year warrantee Cat AA

Labour Charges For Fixing of LED Tube Light with batten suitable for up to 1 x 22 watt LED tube light fitting including tube On surface complete in all respect. Cat-AAA

Labour Charges For Fixing of Fan Sheet of Backelite

Labour Charges For Fixing of ceiling fan ISI Marked 1200 mm sweep. Usha / Crompton/Bajaj make

Labour Charges For Fixing of light duites exhaust fan 12" dia Bajaj / Usha / Cromption make.

Labour Charges For Light duty exhaust fan luvers 12”dia.

Labour Charges For of Loop wiring Light Point from Existing Light Point with 1.5 sq.mm x 2 wire with 1.5 sq.mm earth wire in PVC Conduit pipe.

Labour Charges For Fixing of Al lugs, Gland & PVC Tape etc.

Labour Charges For Laying of G.I. pipe B Class Size 75 mm.

Labour Charges For Laying of G.I. pipe B Class Size 100 mm.

Supply of Electrical Materials

Supply of Required Material for light with 1.5 Sq. mm FR PVC insulated multistrand single core copper conductor cable, PVC conduit with 1.5 Sq. mm FRLSH PVC insuleted multistrand copper conductor cable as earth wire, Modular Box, Covr Plate, Modular type switch & ceiling rose/angle/ batten holder on 3mm thick phenolic laminated backelite sheet etc.

Do as above Item But 2 way Light Point

Do as above Item But Fan/Fresh air Fan Point

Do as above Item But Plug Point

Do as above Item But Call Bell Point

Supply of Required Material for submains with two number 4 sq.mm FRLSH PVC insulated 1100 Volt grade multistrand single core copper conductor cable with 20 mm dia heavy duty (2 mm thick) PVC conduit pipe & one no. 2.5 sq.mm FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire.

Supply of Required Material for submains with two number 6 sq.mm FRLSH PVC insulated 1100 Volt grade multistrand single core aluminium conductor cable with 25 mm dia heavy duty (2 mm thick) PVC conduit pipe & one no. 4 sq.mm FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire.

Supply of Required Material for submains with 4 number 6 sq.mm FRLSH PVC insulated 1100 Volt grade multistrand single core copper conductor cable with 32 mm dia heavy duty (2 mm thick) PVC conduit pipe & 2 nos. 4 sq.mm FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire.

Supply of Required Material for submains with 4 number 10 sq.mm FRLSH PVC insulated 1100 Volt grade multistrand single core copper conductor cable with heavy duty (2 mm thick) PVC conduit & 2 nos. 6 sq.mm FRLSH PVC insulated copper conductor cable as earth continuity wire.

Supply of 200 Amp. four pole change over switch on 50mm x 50mm x 6mm angle iron frame, painting and other material required for proper completion of the work.

Supply of Required Material for single light wall bracket on matching M.D.F.E.G. Board. Cat.-AAA

Supply of Required Material for Aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade. with burnt bricks for on sides and on top. On surface sand M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge. 16 sqmm x 4 core.

35 sqmm x 3½ core.

70 sq.mm x 3½ core.

120 sq.mm x 3½ core.

400 sq.mm x 3½ core.

Supply of Required Material for 25 mm x 3 mm G.I. Strip.

Supply of Required Material for Safe Earthing Electrode T-19, (Hot Dip Galvanized), Length up to 3000 mm, Outer Dia 50 mm, inner Dia 25, terminal Dia 12 mm, outer G.I. pipe of 16 swg and inner G.I. pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity and one earthing lead of 25 mm x 3mm G.I. strip upto switch board with 30 cm square C.I. frame with hinged cover & masonry housing.

Supply of Required Material for factory fabricated and wired metal clad dust and vermin proof floor mounting M.S. Channel Base with bottom and top cable entreis Electrical control panel with TPN MCCB's (Four pole 36 KA with thermal magnatic release) switches complete in all respect with Plinth as per below specification. Indoor Type (For Power) Incoming- 200 Amp MCCB = 1 No. Outgoing- 63 Amp MCCB = 6 Nos.

(For Light & Lift) Incoming - 200 Amp MCCB = 1 No. Outgoing - 100 Amp MCCB = 2 Nos. 63 Amp MCCB = 2 No.

(For A.C. Outdoor Type) Incoming - 200 Amp MCCB = 1 No. Outgoing - 63 Amp MCCB = 6 Nos.

Supply of Required Material for factory fabricated and wired metal clad dust and vermin proof floor mounting M.S. Channel Base with bottom and top cable entreis Electrical control panel with TPN ACB (Four pole65 KA with thermal magnatic release) switches complete in all respect with Plinth as per below specification. (Out Door Type) Incoming - 800 Amp ACB = 1 No. Outgoing - 200 Amp MCCB = 6 Nos.

Supply of 6 Amp. To 32 Amp. SPMCB (10 KA) Cat-A

Supply of 40 Amp. SP MCB (10 KA) Cat - A

Supply of 40Amp. DP MCB (10 KA) Cat.-A

Supply of 63 Amp. TP MCB (10 KA) Cat-A

Supply of 40 Amp 4 pole MCB - (10KA) Cat-A

Supply of Required Material for 63 Amp 4 pole MCB - (10KA) Cat-A

Supply of 80 Amp. To 100 Amp. 4 pole MCCB (16 KA) Thermal Magnetic release. Cat-B

Supply of Required Material for surface/flush mounting 8 ways SPN distribution board with additional metal door without MCB. Cat-A

Supply of Required Material for surface/Flush mounting 4 ways TPN distribution board with additional metal door without MCB. Cat.-A

Supply of Required Material for surface/flush mounting 8 ways V TPN distribution board with addition metal board without MCB. Cat-A

Supply of Required Material for surface/flush mounting 8 ways V TPN distribution board with addition metal door without DPX3 160 MCCB. Cat-A

Supply of Required Material for call bell of approved make MDFEG/ Teak ply board.

Supply of Required Material for 16 gauge M.S. drum duly painted including making hole in the wall for exhaust fan and finishing properly.

Supply of Required Material for Fire extinguisher, ABC Type 6.00 Kg. capacity (ISI marked IS: 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials.

Supply of Required Material for Co2 type Fire extinguisher, 4.5 Kg. capacity (ISI marked IS: 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials.

Supply of Required Material for fire bucket, round bottom made of G.I. Sheet 9-11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chined and locked, initially filled with fine river sand, water as per directions of Engineer-in-charge.

Supply of Required Material for shock treatment chart (Prescribed under I.E Rule) duly framed with glass and supported from back with hard board or soft board.

Supply of Required Material for 1800 mm x 900 mm x 12 mm thick chequered rubber matting of tested quality.

Supply of Required Material for Power plug with 20A/250 volt flush type modular switch and 5 pin 20A/250V flush type universal modular socket switch on concealed M.S. box including supply of all material.

Supply of Required Material for hexagonal/Round G.P. fan box of approved make made up 1.0 mm thick ISI Marked G.P. sheet spot welded four to Eight holes of 25.4 mm for pipe entry of the box. Holes should be semi-shuttered type with 0.5 mm G.P. sheet made upper & lower cover duly screwed fitted with 300 mm round zink coted M.S. bar x 12 mm & brand name should be embossed.

Supply of Required Material for Electronic fan regulator(Modular) 120-280 V. ISI marked, on the existing switch board including making connections, required material.

Supply of Required Material for submain with two number 2.5 sq.mm FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable with 20 mm dia heavy duty (2mm thick) PVC conduit pipe & 1 nos. 1.5 sq.mm FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable as earth continuity wire.

Supply of Required Material for submain with two number 1.5 sq.mm FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable with 20 mm dia heavy duty (2mm thick) PVC conduit pipe & 1 nos. 1.5 sq.mm FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable as earth continuity wire.

Supply of Required Material for recess/Surface mounting round 18 watt to 20 watt Cut out Min 150mm, Height Min 40mm, LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/Reflector and driver set, suitable for 24Hr Continuous Operation, complete in all respect. 1800-2000 system lumens, 1001m/watt, PF>0.95, THD<10%, at full load CRI>80, with 3 year warrantee Cat AA

Supply of Required Material for LED Tube Light with batten suitable for up to 1 x 22 watt LED tube light fitting including tube On surface complete in all respect. Cat-AAA

Supply of Required Material for Fan Sheet of Backelite with brass M/C screw & brass cup washer.

Supply of Required Material for ceiling fan ISI Marked 1200 mm sweep. Usha / Crompton/Bajaj make

Supply of Required Material for light duites exhaust fan 12" dia Bajaj / Usha / Cromption make.

Supply of Required Material for Light duty exhaust fan luvers 12”dia.

Supply of Required Material for Loop Light Point from Existing Light Point with 1.5 sq.mm x 2 wire with 1.5 sq.mm earth wire with PVC Conduit pipe.

Supply of Required Material for Al lugs, Gland & PVC Tape etc.

Supply of Required Material for G.I. pipe B Class Size 75 mm.

Supply of Required Material for G.I. pipe B Class Size 100 mm.

12.5 % bulkage will be deduct from course sand

All rates are F.O.R. Site i/c loading unloading & stacking

G.S.T. Extra as applicable.

All Material will be as per UPPWD Specification & Approved Make.

Genuineness of Panel Board for the purchase of Panel Board from UPPWD Approved manufacturer. must be

Electrical Material make & Specification as per enclosed list.

"A" class license holder who valid license from director electrical safety U.P. Government.

Supply of Civil Materials

Bricks Class M-150

Course sand (Hameerpur)

Cement PPC (packed in 50 kg bag) make- Birla,Prism, ACC, Mycem,J.P.

TMT steel MS round bar confirming FE-500 I.S.I.

Mahesh and Copany