Providing Special Repair Addition Alteration of E.I in set No. 5 8 in Block No. 1 type III Qtr. At U.S Club Shimla-1.

Amount

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required.

Group B.

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2x1.5 Sq. mm.

2x4. Sq. mm.

4x4 Sq.mm

Supplying and fixing metal box of 100mmx100mmx60mm deep (nominal size) on surface/recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 5 pin 5/6 amps socket outlet and 5/6 amps, piano type switch, connections, painting etc. as required.

Supplying and fixing metal box of 180mmx100mmx60mm deep (nominal size) on surface/recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 5 pin 15/16 amps socket outlet and1 5/16 amps, piano type switch, connection

Supplying and fixing bakelite batten/angle holder including connections etc. as required:-

Providing and installation of stationary storage type Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and fixing of Non-return valve, Dead weight safety valve, 2 No C.P. connection rods 18" long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc. as required:-

25 Liter capacity water heater (Cat-A)

Providing and installation of following type of ultra slim decorative LED batten with extruded aluminium heat sink, with anti glare polycarbonate diffuser and energy efficient constant current, integral electronic driver; suitable for input voltage: AC 220-240 V, 50/60Hz, complete with all accessories, including mounting clips & loop in loop out wire, connections, testing and commissioning etc. as required. Make: ,Philips, Syska, GE, Bajaj, C&S, Panasonic or any other approved by Engineer-in-Charge.

LED Batten20 watts

Supplying and fixing sheet metal bus-bar chamber suitable for 200 Amp. 415 volts capacity with 4 No. copper strip bus-bars each of length 600mm & cross-sectional area (25.4mmx4.75mm), enclosure made from 1.6 mm thick M.S. sheet having overall dimensions (680mmx450mmx150mm) nominal with all accessories including connections, earthing the body etc. as required:-

Providing and fixing following rating and breaking capacity MCCB in the existing cubical panel board including drilling holes in the cubicle panel, making connections, etc. as required.

200 Amp. -25 KA

Providing and fixing TP&N switch disconnector fuse unit cubical type, 415/500 volts with 3 No. HBC/HRC fuses, in sheet steel enclosure including drilling holes on the board, connections, earthing the body etc. as required.

100 Amp. Category-A

Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade direct in ground; to be laid 1 meter below the ground level including excavation sand cushioning, protective covering and refilling the trench etc. of the required size:-

Armoured cable 35 sq. mm (3.5 core)

Providing & fixing sheet steel enclosure suitable for 3 pole and 4 pole MCCB DU/ DH MCCB ,havinggenerous space for cable termination inbuilt , interlink and neutral link for TP&N etc. as required in/c drilling holes on the existing board , wall etc, as rquired

SHUBHAM THAKUR