Repair maintenance of DG set incl LT cables panels changeover and allied works and repair maintenance of EOT cranes of ESH inside Depot area Sewar Fort and KLP area under GE Bharatpur

Amount

Comprehensive maintenance (Consisting of normal repairs) preventing maint as per OEM direction Ones in four months of electrically operated travelling (EOT) Flame Proof cranes of capacity 5 Ton make: Rock well & Cranex at site complete all as specified and directed by Engineer -in- Charge Note: - (a) The crane shall be repaired by OEM or its authorised service Engineer/workshop/channel partner. (b). Replacement of the unserviceable spare parts shall be measured and paid sepreatly. (i) Long Traverse (a). Cleaning of Gear box and oil level checking rectification of leakages if any. (b). Checking Assembly vibration. (c). Brake Adjustment. (d). Long Traverse wheel checking for any noise. (e). Geared couplings - grease checking and nut tightening. (f). Checking of hydraulic oil in thrustor brake (g). Checking of electric motor connections (h). To check the cut off at extreme end with limit switch. (i). Checking and greasing \ oiling of plumber block. (j). Long traverse.

(ii) Cross Traverse (a). Cleaning of Gear box and oil level checking rectification of leakages if any. (b). Checking Assembly vibration. (c). Brake Adjustment. (d). Long Traverse wheel checking for any noise. (e). Geared couplings - grease checking and nut tightening. (f). Checking of hydraulic oil in thrustor brake (g). Checking of electric motor connections (h). To check the cut off at extreme end with limit switch. (i). Checking and greasing \ oiling of plumber block. (j). Cross traverse. (iii) Hoist Motion (a). Gear box oil level check & rectification of leakages. (b). Checking Assembly vibration. (c). Brake Adjustment. (d). Checking for the main bearing of the rope drum including greasing. (e). Geared couplings - grease checking and nut tightening. (f). Checking of hydraulic oil in thrustor brake. (g). Checking of electric motor connections. (h). Checking wire rope & greasing.

(i). Adjustment of rotory limit switch. (j). Bearing grease \ oiling in bottom block \ hock. (k) Repairing/straingthnening of hoist limit mechanism rod with adjustable coupling. (iv). Electrical Network (a). Checking the contractor for overheating and flashing. (b). general checking of contacts and connections. (c). Cleaning of control panels. (d). Checking of connection AC Drive and othher drives for smooth functioning of the same. (v). Down shop lead (DSL) (a). Checking the alingment and rectification. (b). Cleaning of the moving \ slidding objects.

Comprehensive maintenance (Consisting of normal repairs) preventing maint as follows Ones in four months of electrically operated travelling (EOT) cranes of capacity 2 Ton make: Rock well at site complete all as specified and directed by Engineer -in- Charge Note: - (a) The crane shall be repaired by OEM or its authorised service Engineer/workshop/channel partner. (b). Replacement of the unserviceable spare parts shall be measured and paid sepreatly. (i) Long Traverse (a). Cleaning of Gear box and oil level checking rectification of leakages if any. (b). Checking Assembly vibration. (c). Brake Adjustment. (d). Long Traverse wheel checking for any noise. (e). Geared couplings - grease checking and nut tightening. (f). Checking of hydraulic oil in thrustor brake (g). Checking of electric motor connections (h). To check the cut off at extreme end with limit switch. (i). Checking and greasing \ oiling of plumber block. (j). Long traverse. (ii) Cross Traverse (a). Cleaning of Gear box and oil level checking rectification of leakages if any.

(b). Checking Assembly vibration. (c). Brake Adjustment. (d). Long Traverse wheel checking for any noise. (e). Geared couplings - grease checking and nut tightening. (f). Checking of hydraulic oil in thrustor brake (g). Checking of electric motor connections (h). To check the cut off at extreme end with limit switch. (i). Checking and greasing \ oiling of plumber block. (j). Cross traverse. (iii) Hoist Motion (a). Gear box oil level check & rectification of leakages. (b). Checking Assembly vibration. (c). Brake Adjustment.

(d). Checking for the main bearing of the rope drum including greasing. (e). Geared couplings - grease checking and nut tightening. (f). Checking of hydraulic oil in thrustor brake. (g). Checking of electric motor connections. (h). Checking wire rope & greasing. (i). Adjustment of rotory limit switch. (j). Bearing grease \ oiling in bottom block \ hock. (iv). Electrical Network (a). Checking the contractor for overheating and flashing. (b). general checking of contacts and connections. (c). Cleaning of control panels. (d). Checking of connection AC Drive and othher drives for smooth functioning of the same. (v). Down shop lead (DSL) (a). Checking the alingment and rectification. (b). Cleaning of the moving \ slidding objects. Ditto as per sr No 1 above but for electrically operated travelling (EOT) cranes of capacity 2 Ton make: Rock well

Comprehensive maintenance (Consisting of normal repairs) preventing maint as follows Ones in four months of mechanically operated cranes of capacity-03 Ton at 8 MSD shed,39 FAD area including cheking of strength and proper functioning of chain pulley and chain at site, greasing/oiling, hoist streingthnening/repair work complete all as specified and directed by Engineer -in- Charge

M&L for painting of 05 Ton EOT crane ,applying one coat of red oxide primer and two coat of synthetic enamled spray paint of existing color on different surafces incl preparing of old steel surface by scratching/removing rust, dust and old paint etc with wire brush, emery paper, grinder etc and making surfaces smooth for achieving better grip between surafce and primer, complete all as directed by Engr-in-charge.

M&L for painting of 02 Ton EOT crane ,applying one coat of red oxide primer and two coat of synthetic enamled spray paint of existing color on different surafces incl preparing of old steel surface by scratching/removing rust, dust and old paint etc with wire brush, emery paper, grinder etc and making surfaces smooth for achieving better grip between surafce and primer, complete all as directed by Engr-in-charge.

Attending Complaints and rectification of electronic, electrical and mechanical defects by authorized experience technician for flame proof EOT crane of capacity upto 5 Ton, Checking of uncerviciable electrical system and find out defect of control wiring in control panel (Hoist, Long Travel, Cross Travel) Control Switch Limit Switch Rectified the same and made serviciable complete and testing thereafter complete all as specified and directed by engineer - in - charge. Note: - (a). The complaint shall be notified to the contractor by engineer - in - charge / JE E&M telephonically / personnaly / by SMS recorded in the register mentioned for the purpose. (b). Contractor shall make neccessary arrangement to attend the complaint. (c). Cost of any minor nature of repair / replacement of petty item such as nuts, bolts, washers, screws, piece of electrical cable upto 0.5 meter length etc, is deemed included in the unit rate quoted by the contractor. (d). Any other major item / repair required for the rectification shall be measured and paid seperately under respective item of the schedule as supply only.

Supply only single phase preventer for EOT crane & connecting complete all as directed by Engr- in- Charge. Make:- L&T / BCH / Minilec

Supply only Power contractor 09A AC3 3 phase 415V AC with 1NO + 1NC , auxiliary contact,Coil voltage 24V DC Make:- Schneider, L&T, Siemens

Supply only Power contractor 25A AC3 3 phase 415V AC with 1NO + 1NC ,auxiliary contact ,Coil voltage 24V DC Make:- Schneider, L&T, Siemens

Supply only Power contractor 18A AC3 3 phase 415V AC with 1NO + 1NC ,auxiliary contact, Coil voltage 24V DC Make:- Schneider, L&T, Siemens

Supply only Power contractor 16A AC3 3 phase 415V AC with 1NO + 1NC ,auxiliary contact, Coil voltage 110V DC Make:- BCH, L&T, Siemens

Supply only Power contractor Size 3 45A AC3 3 phase 415V AC with 1NO + 1NC ,auxiliary contact ,Coil voltage 110V DC Make:- BCH, L&T, Siemens

Supply only Thermal overload relay 3 phase 415V AC relay range 12-18A Make:- Schneider, L&T, Siemens

Supply only Thermal overload relay 3 phase 415V AC relay range 2.5 - 4A Make:- Schneider, L&T, Siemens

Supply only Step Down Transformer double wound, 415-400-380-0/0,12,24,30,110V AC 100VA Make:- USGC, VK, Crane Control

Supply only Step Down Transformer 415-400-380-0/0,110,220V AC 0.5KVA Make:- USGC, VK, Crane Control

M&L for Repairing of electric motor of EOT crane, AC 3 phase, by dismantling the motor and taking out the old winding wires, cleaning the slots, rewinding the motor with appropriate size of super enamelled copper winding wire, and varnishing complete including replacing the worn out bearing reassembling the motor fixing in same position and testing complete all as specified and directed by Engr In charge. Note : The quoted rate shall be deemed to be included for cost of roller & bearing.

Supply only MCB 40A, TP, 415V AC. Make:- Schneider, L&T, Siemens

Supply only MCB 10-16A, TP, 415V AC. Make:- Schneider, L&T, Siemens

Supply only AC Drive(VVVF) 7.5KW G7 HD 3 Phase 415V AC Make:- Yaskawa, L&T, Siemens

Supply only AC Drive(VVVF) 5HP, HD, 3 Phase 415V AC Make:- Yaskawa, L&T, Siemens, Schneider

Supply only Dynamic Braking Resistance (DBR) Aluminium Clad type 2000W, 100ohms Make:- Speedage, USGC, Laxman Electronics.

Supply only Dynamic Braking Resistance (DBR) Aluminium Clad type 1000W, 50ohms Make:- Speedage, USGC, Laxman Electronics.

Supply only Rubber Buffer Size 90mm round with bolt Make:- Speedocontrol, USGC, Laxman Electronics.

Supply only Rubber Buffer Size 120mm round with bolt Make:- Speedocontrol, USGC, Laxman Electronics.

Supply only Flame Proof Hydraulic Thyristor Brake 100mm Make:- Shyam Switchgear, USGC, Sudhir Switchgear.

Supply only Flame Proof Hydraulic Thyristor Brake 160mm Make:- Shyam Switchgear, USGC, Sudhir Switchgear.

Supply only Flame Proof Hydraulic Thyristor Brake 200mm Make:- Shyam Switchgear, USGC, Sudhir Switchgear.

Supply only Flame Proof Hydraulic Thyristor 18Kg, 3 Phase 415V AC Make:- Shyam Switchgear, USGC, Sudhir Switchgear .

Supply only Flame Proof Rotary type limit switch Make:- Shyam Switchgear, USGC, Sudhir Switchgear .

Supply only MSP Relay 110V AC, 3P Make:- Salzer, PLA, Omron.

Supply only MS Equalizing Pully of size 250mm with center bore 80mm. Make:- USGC, SS Engineering, GPS Crane.

Supply only Sperical Ruler Bearing 22211. Make:- SKF, NSK, Norma

Supply only Sperical Ruler Bearing 22208. Make:- SKF, NSK, Norma

Supply only Steel Wire Rope 12mm FMC, Construction 6x36. Make:- Usha Martin, Fort William, Mahadev.

Supply only Cable Resting Trolley with wheel Make:- USGC, SS Engineering, GPS Crane.

Supply only PVC felexible cable 1.5sqmm, 16 core, copper Make:- Finolex, Havells, Polycab.

Supply only PVC felexible cable 4sqmm, 3 core, copper Make:- Finolex, Havells, Polycab.

Supply only PVC wheel roller of existing size for supporting DSL cable of size 4sqmm X 3core copper conductor cable complete all as specified and directed

Supply only gear oil in gear box, Type:- EP140 oil Make:- HPL, Caltex, IOC

Supply only hydraulic break fluid Make:- IOC, Caltex, Shell

Supply only burn out break shoe liner of LT,CT,Hoist brake of 200mm, 160mm, 100mm, Dia for 5Ton capacity Flame proof EOT Crane all as directed by engineer in charge.

M&L Carrying out 'B' check ones in six months as per OEM for 70 KVA water cooled by unscrewing nuts, bolts and servicing of DG set by authorised wrksp with changing of coolant, belt greasing and oiling of parts and toping up, cleaning of inner body of diesel tank by removing sludge etc and cleaning of Radiator assembly complete with chemical and reassembling the DG set after repair/Replacement of unserviceable parts and testing complete in all respect as directed by Engineer-in-Charge. Note:-(a) The DG set shall be repaired by OEM or its authorised service Engineer/workshop/channel partner at site. (b)The cost of following Spare parts shall be deemed to be included under quoted rates. (a) Fuel Filter (b) Oil Filter (c) Main Element for Air Cleaner (d) Testing of battery with top up required distilled water (e) Burnt out battery terminal (f) Coolant

All description as per item no. 43 of capacity of DG Set 50 KVA

All description as per item no. 43 of capacity of DG Set upto 40 KVA

All description as per item no. 43 of capacity of DG Set 93KW diesel engine

All description as per item no. 43 of capacity of DG Set 62.5 KVA

All description as per item no. 43 of capacity of DG Set 500 KVA

All description as per item no. 43 of capacity of DG Set 125 KVA

M&L Carrying out 'C' check after 1500Hrs running as per OEM for 500 KVA water cooled by unscrewing nuts, bolts and servicing of DG set by authorised wrksp with changing of coolant, belt greasing and oiling of parts and toping up, cleaning of inner body of diesel tank by removing sludge etc and cleaning of Radiator assembly complete with chemical and reassembling the DG set after repair/Replacement of unserviceable parts and testing complete in all respect as directed by Engineer-in-Charge. Note:-(a) The DG set shall be repaired by OEM or its authorised service Engineer/workshop/channel partner at site. (b)The cost of following Spare parts shall be deemed to be included under quoted rates. (a) Fuel Filter (b) Oil Filter (c) Main Element for Air cleaner (d) Testing of battery with top up required distilled water (e) Burnt out battery terminal (f) Coolant (g) Radiator cleaning with chemical (h) Check all electric terminal & thimbles (j) Check pollution level

All description as per item no. 50 of capacity of DG Set 70 KVA

Attending Complaints and rectification of electronic, electrical and mechanical defects by authorized experience technician for DG set of capacity upto 500KVA, Checking of uncerviciable electrical system and find out defect of control wiring in control panel/changeover,checking of engine/alternator/dynamo /canopy and rectified the same and make serviciable complete and testing thereafter complete all as specified and directed by engineer - in - charge. Note: - (a). The complaint shall be notified to the contractor by engineer - in - charge / JE E&M telephonically / personnaly / by SMS recorded in the register mentioned for the purpose. (b). contractor shall make neccessary arrangement to attend the complaint. (c). Cost of any minor nature of repair / replacement of petty item such as nuts, bolts, washers, screws, piece of electrical cable upto 0.5 meter length etc, is deemed included in the unit rate quoted by the contractor. (d). Any other major item / repair required for the rectification shall be measured and paid seperately under respective item of the schedule as supply only.

M&L for making good to exhaust Pipe of existing size by welding and fixing asbestos rope of suitable size over complete length incl suitable size of pipe approx 3 Mtr lengh all as specified and directed by Engr-in-charge.

S&F muffler system for 500KVA DG set at existing location incl necessary civil work ie making suitable opening form existing stone massonary wall and incl necessary welding work all as specified and directed by Engr-in-charge.

S&F Electric Coil of Power contractor upto 125 KVA capacity DG Set complete all as directed by Engr-in-charge.

S&F Radiator Hose Kit of 500 KVA capacity DG Set complete all as directed by Engr-in-charge.

M&L for electrical rubber chequred mat, size 2 m x 1 m x 19 mm complete all as specified and as directed.

Supply only pressure gauge, 100 mm size, fitted on delivery side of pump set , including dismantling the old one complete all as specified and as directed.(Make : H-Guru/Fiebig)

M & L for Repairing radiator for 500 KVA DG set including dismantling from engine/canopy and taking to the workshop for necessary welding / brazing, descaling work etc including testing for leaks if any , steam washing the radiator and refixing on the engine/canopy complete all as specified and as directed.

All as per item No 59 above but 50 to 70 KVA capacity

All as per item No 59 above but 12.5 to 40 KVA capacity

Dismantling the UNSV Automatic voltage Regulator of the 500 KVA DG set and replacement of the same with new as per existing make and size and fixing and testing complete

Dismantling the UNSV Automatic voltage Regulator of the 70 KVA DG set and replacement of the same with new as per existing make and size and fixing and testing complete

Dismantling the UNSV Automatic voltage Regulator of the 62.5 KVA DG set and replacement of the same with new as per existing make and size and fixing and testing complete

Dismantling the UNSV Automatic voltage Regulator upto 40 KVA DG set and replacement of the same with new as per existing make and size and fixing and testing complete

S&F of battery terminal copper conductor 70 sqmm with end joint of claims and socket suitable for 12 Volts battary one meter long of red/ black colour all as directed by Engineer-in-Charge.

S&F in replacement battery 12 volts, 80 AH capacity with initial charging suitable for DG sets complete all as specified and directed, Make-Exide or equivalent make as specified in Appx B

S&F in replacement battery 12 volts, 150 AH capacity with initial charging suitable for DG sets complete all as specified and directed, Make-Exide or equivalent make as specified in Appx B

S&F in replacement battery 12 volts, 200 AH capacity with initial charging suitable for DG sets complete all as specified and directed, Make-Exide or equivalent make as specified in Appx B

S&F in repairs ON LOAD change over switch 415V ,sheet metal enclosures 4 pole of capacity 800 Amps. Make: L&T or equivalent make specified in Appx B

S&F in repairs ON LOAD change over switch 415V ,sheet metal enclosures 4 pole of capacity 200Amps. Make: L&T or equivalent make as specified in Appx B

S&F in repairs ON LOAD change over switch 415V ,sheet metal enclosures 4 pole of capacity 100Amps. Make: L&T or equivalent make as specified in Appx B

S&F in repairs ON LOAD change over switch 415V ,sheet metal enclosures 4 pole of capacity 63Amps. Make: L&T or equivalent make as specified in Appx B

S & F MCCB 04 pole 415 volts ,thermal magnatic release,adjustable type,200 Amps 36 KA rupturing capacity Make L&T or equivalent make as specified in Appx B

S & F MCCB 04 pole 415 volts ,thermal magnatic release,adjustable type,100 Amps 30 KA rupturing capacity Make L&T or equivalent make as specified in Appx B

S&F in repairs starter display card of DG set of capacity upto 62.5 KVA of existing size and model all as specified and directed by Engineer-in-charge.

Supply and fix in repair ignition switch with key for DG sets of any capacities fixed in position & connecting complete all as directed by Engr-in-Charge.

Supply and fix in repair rubber hose pipe for air with connecting fitting & fixture suitable for 500/ 125/70 / 63.5/50/ 40 KVA DG Set of Make:- Kirloskar / Cummins / Greaves

Supply and fix in repair coupling bushes suitable for 40 KVA to 100 KVA capacity DG Set, fixed in position including proper alignment of Engine and Alternator suitable for DG set Make:- Kirloskar / Cummins / Greaves

Supply and fix in replacement of self starter 24 V with solenoid coil assembly complete fixed to DG set of 500KVA complete all as specified & directed by the engineer-in-Charge Make:- Auto lek / TVS Lucas or equivalent make approved by the GE

M&L for taking out self starter of 12 volts DC from DG set, servicing of starter including replacement of clutch plate, moving control pinion, spring etc, fixed in same position complete all as specified & directed by Engineer-in Charge. Make:- Lucas/Mica Note :- The following works is included in the unit rate of contract quoted by contractor:- (i) Rewinding of pinion assembly with suitable size of copper wire , varnishing and heating etc. (ii) Replacement of worn out field coil (iii) Replacement of clutch plate assembly(iv) Replacement of solenoid switch

M&L for servicing and overhauling of dynamo/alternator including eplacement of unsv parts such as carbon brush, armature winding, varnishing of coil and reassembling and fitted with the engine including testing complete of capacity 12 volts.

Supply and fix in replacement of self starter 12 V with solenoid switch assembly complete fixed to DG set of any capacity complete all as specified & directed by the engineer-in-Charge Make:- Auto lek / TVS Lucas or equivalent make approved by the GE

Supply and fix in repair flexible diesel pipe with banjo bolts and washers suitable for 40/50/63.5 / 70 / 100/500 KVA DG sets complete all as specified & directed by the Engineer-in-Charge Make:- Kirloskar / Cummins / Greaves

Supply only Engine oil grade 20W 40 for incorporation against item No. 83 to 84 Make : Castrol/Servo

Taking down old unserviceable LT cable of size upto 240 Sqmm all as specified and directed by Engr-in-charge

Excavation in trenches not exc 1.5 M wide and not exc 1.5 M in depth for pipe line, etc in soft / loose soil getting out and levelling of bottom surface to required level all as specified and as directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25 Cm thick soft / loose soil all as specified and as directed.

Removing excavated material (Soils) from site to a distance not exc 50 M away and depositing where directed at a level not exc 1.5mtr above the starting point all as specified and as directed.

Supply & spread unwashed dry river sand for sand cushioning and covering the under ground cable in trenches. (Note :- Punning thickness shall be measured.)

M&L for brick protection with sub Class`B` bricks old size laid dry, flat over cable perpendicular across the cable in trenches complete all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor complete of following sizes:-

150 Sqmm 3.5 core

70 Sqmm 3.5 core

25 Sqmm 4 core

Supply, laying, testing & commissioning LT XLPE insulated armoured (heavy duty) electric cable of single core 95 Sqmm with stranded copper conductor 1100 volts grade (ISI marked) & laid in trenches/pipes or fixed on pole from existing DG to LT Panel complete all as specified and directed.

Supply, laying, testing & commissioning LT XLPE insulated armoured (heavy duty) electric cable of single core 70 Sqmm with stranded copper conductor 1100 volts grade (ISI marked) & laid in trenches/pipes or fixed on pole from existing DG to LT Panel complete all as specified and directed.

Boring of holes under road, pavement, hard standing by trenchless technology using suitable tools and machinery for laying of pipe upto 150mm bore complete all as specified and as directed . Note :- GI pipe shall be measured and paid in concern Item

S&L pipe galvanised medium grade 80mm bore complete including fittings

Out going- (a) MCB TPN 40 Amp,'C' curve ,10kA rapturing capacity-02 Nos (b) MCB SP 6 Amp,'C' curve ,10kA rapturing capacity-12 Nos (c) MCB SPN 32 Amp ,'C' curve, 10kA -02 Nos Note: (i) Drawings of LT panel shall be got approved by GE before Manufacture. (ii) Panel stand shall be made out of 50X50X5mm ISA angle of 60cm height and appropriate size as per panel. The same should be fixed in PCC 1:2:4 below ground level embedded in block of size 30X30X45cm.

Note: (i) Drawings of LT panel shall be got approved by GE before Manufacture. (ii) Panel stand shall be made out of 50X50X5mm ISA angle of 60cm height and appropriate size as per panel. The same should be fixed in PCC 1:2:4 below ground level embedded in block of size 30X30X45cm.

(e) Indicator lamp for three phase and seletor switch complete as required Note: (i) Drawings of LT panel shall be got approved by GE before Manufacture. (ii) Panel stand shall be made out of 50X50X5mm ISA angle of 60cm height and appropriate size as per panel. The same should be fixed in PCC 1:2:4 below ground level embedded in block of size 30X30X45cm.

Taking out DG set of any capacity from existing location and fixing after necessary repair work incl disconnecting earhing strip /LT cable and reconnecting after work done complete all as specified and directed Engr-in-charge.

Demolotion of PCC at site complete all as specified & directed.

M&L for cement concrete 1:4:8 type D2 (using 40 mm graded crushed stone aggregate) as in foudation,fillinf and mass concrete complete all as specified and directed by Engr-in-charge

M&L for cement concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate for pedestal of poles/ coping including necessary formwork, fair finishing to exposed surfaces using extra cement all as specified and directed by Engr-in-charge

S&F in replacement of Lithium base Energy efficient integrated Solar street light of 36 watt in single FRP body duly polyurethane coating (Camouflage color), encases with monocrystalline solar PV panel of 65-67Wp,lithium battery 11.1/12.8V,33.0 AH with inbuilt BMS,IP 65, High brightness W-LED(160-180lm/watt) lamp with Aluminium reflector for better light distribution ,CRI>70, color temp 5700K-6500K Microcontroller based charge controller cum driver,automaticdimming function(First 04 hrs at full brightness & rest of the time at lower light level with PIR motion sensor), Dusk to dawn operation,suitable to working temp (-) 10C to (+) 55C ,weight not more thatn 16-18 Kg with adjustable MS clamp suitable for pole/wall mounting etc complete as reequired.Make: AXXON/HAVELLS/PHILLIPS Protections: Short circuit, overload,Reserve polarity and battery protection.Firm should provide vital parametres Test report from NABL accredited lab and should be of made in India with CE & ROHS complaint.

M & L for Earthing complete with Galvanised steel earth plate electrode 600 x 600 x 6 mm buried directly in the ground vertically to depth not less than 2.25 Mtr below the ground level with the top edge of earth plate, depth not less than 1.5 Mtr below the ground level connected to GI earth strip of 32 mm x 6 mm size by means of bolts, nuts and washers protected by GI tubing light grade 40 mm dia uptoTest point 20 mm dia watering pipe medium grade with funel & wire mesh, PCC pit in PCC 1:2:4 using 20 mm stone aggregates chamber 40 mm thick PCC cover slab (1:2:4) type B-1 using 20 mm graded stone aggregates complete all as specified and shown in electrical plate No.3 of SSR Part-I including earth work in any type of soil ,removal of surplus soil and providing charcol dust & salt layers all around the earth plate upto 15 cm all as required specified & directed by engr in charge.

M/s Ranaji Construction Co

PD GUPTA AND COMPANY

M/s Yash Electrical and Maintenance

M/S MAKHIJA TRADERS

Vijay Electricals

Bluemax Associate