Proposed Development of Various Samaj Mandir, GYMS, Samaj Bhawans in MBMC Area. (Basic Facility Development Fund)

Amount

Description

ITEM NO 01 Providing detailed geological reports of proposed site by maintaining geotechnical investigation of structure stratification collecting soil, rock and ground water samples for laboratory tests to arrive the foundation design parameters . Rock properties such as type of rock, jointing fractures, etc. complete with suggestion about the site foundation and remedies. SSR 1.57/20

ITEM NO.02 Removing cement tiles,or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete SSR 46.19/297

ITEM NO.03 Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc. SSR 46.09/296

ITEM NO.04 Dismantling stone masonry in lime or cement mortar including stacking the materils as directed with all leads, lifts etc. SSR 46.11/296

ITEM NO.05 Dismantling the R.C.C. Work 1:2:4 and sorting out the materials such as steel etc. as directed and stacking them within the specified lead as directed etc. complete. SSR 46.29/297

ITEM NO 06 Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 10.0 to 19.0 BHP pump etc. complete. (prior approval of Superintending Engineer will be necessary) SSR 12.24/86

ITEM NO 07 Excavation for foundation in earth ,soil of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete. (Lift upto 0.00 to 1.50 m.) By Manual Means SSR 21.01 / 153

ITEM NO 08 Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means SSR 21.02 / 153

ITEM NO 09 Excavation for foundation in earth, soils of all types, sand,gravel and soft murum, including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) By Mechanical Means SSR 21.04 / 153

ITEM NO.10 Excavation for foundation / pipe trenches in slush muddy /marshy / slushy / soil including use of poclain, labour for dewatering during execution including removing the excavated material upto a distance of 50 metres and lifts as below, stacking and spreading as directed, preparing the bed by cleaning the mud, labour required for execution for shuttering item but excluding backfilling, etc. complete. Providing and fixing shuttering shall be paid separately. MJP DSR/53/8

ITEM NO 11 Excavation for foundation in hard murum and boulders including removing the excavated material up to a distance 50 metres, beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5m.) By Mechanical Means SSR 21.10/154

ITEM NO 12 TRANSPORTING OF EXCAVATED MATERIALS lead 20.00 k.m. SSR in Statement C 1 (Page 560)

ITEM NO 13 Filling in plinth and floors with approved excavated material in 15cm. to 20cm. layers including watering and compacting etc. complete. SSR 21.36/157

ITEM NO 14 Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete. SSR 21.37 / 157

ITEM NO 15 Watering and compacting of embankment formed of materials obtained from the road cutting within a lead of 50 m, not less than 97 % of standard Proctor density after laying them in layers of 20 cm. to 30 cm. with vibratory roller. SSR 2.23/24

ITEM NO 16 Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. SSR 21.38 / 157

ITEM NO 17 Providing and laying Cast in situ/Ready Mix cement concrete in M20 of trap/ granite/ quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade ) (PCC) SSR 24.10 / 176

ITEM NO 18 Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C columns and steel stanchion etc. columns as per detailed designs and drawing or as directed including Steel centering formwork, cover blocks laying/pumping, compaction finishing the formed surface with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 25.15/178

ITEM NO 19 Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal fo R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork,cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate ( Crushed sand VSI Grade ) SSR 25.35/180

ITEM NO.20 Providing and laying Cast in situ/Ready Mix cement concrete in M-30 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 26.19/185 RA

ITEM NO.21 Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/ pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade ) SSR 25.54 /181

ITEM NO 22 Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate ( Crushed sand VSI Grade ) SSR 25.74 / 183

ITEM NO 23 Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. SSR 26.33 / 188

ITEM NO 24 Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. SSR 23.01/173

ITEM NO 25 Providing structural steel work in trusses, other similar trussed purlins and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting fixing in position, Making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it 2 coats of oil painting approved quality and shade etc. complete. SSR 23.04 /173

ITEM NO.26 Providing and fixing double scaffolding system (cup lock type) on The exterior side of building/structure, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works. SSR 46.42/299

ITEM NO 27 Centering and shuttering of steel plates with M.S. Angles including strutting, propping etc. and removal of form for Cornices and mouldings. MCGM R3-CS-CW-30-j

ITEM NO 28 Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete SSR 27.05 / 197

ITEM NO 29 Providing uncoursed rubble masonry of trap / granit / quartzite / gneiss stones in cement mortar 1:6 in superstructure including racking out joints when plastering is to be done / striking joints when no plastering is to be done on inside watering and scaffolding etc.complete. SSR 28.04/199

ITEM NO 30 Providing coursed rubble masonry second sort of trap / granite / quartzite / gneiss stones in cement mortar 1:6 in superstructure including raking out joints when plastering is to be done and striking joints when no plastering is to be done on the inside, watering scaffolding etc.complete SSR 28.10/146

ITEM NO 31 Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete SSR 32.11 / 209

ITEM NO 32 Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimeter thickness on previously plastered surface, including Plaster Groove 6mm thickness or Tape Grooves 35 to 45 mm thickness or as required, in all position including preparing the surface, scaffolding etc. complete. SSR 32.32/211

ITEM NO 33 Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases(NOx, VOC‘s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 Kilogram/15 l). plaster crack should be filled by Acrylic base Crack seal/Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company technologist SSR 50.79/ 346

ITEM NO 34 Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. SSR 32.04 / 209

ITEM NO 35 Providing and applying plaster with plaster of paris in 6mm thickness to previously plaster surface in all position including preparing the surface scaffolding etc. complete. SSR 32.27/210

ITEM NO 36 Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete. SSR 35.21 / 225

ITEM NO 37 Providing and applying pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete. SSR 35.23 / 225

ITEM NO.38 Providing and laying pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and technical specifications etc. complete. (by stone/boulder) SSR 14.72/501

ITEM NO.39 Providing and laying weep holes of 100 mm diameter PVC pipes as per drawing for abutment returns, return walls etc. Complete. SSR 17.37/132

ITEM NO 40 Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete.b) Skirting SSR 33.41 / 266

ITEM NO.41 Providing and laying vitrified matt fininsh tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete. SSR 33.42/217

ITEM NO.42 Supply & Fixing of Rock / Stone Finished outdoor vitrified flooring Tiles 20 mm thick and required width wide in plain pattern including Cement float, filling joints, with neat cement slurry, Natural sand, curing and cleaning complete. with prior approval of concerned Superitending Engineer. SSR 50.13/332

ITEM NO 43 Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiski flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. SSR 33.67/220

ITEM NO 44 Providing and laying ceramic tiles having size 30 cm. x 60 cm. confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. SSR 33.27/264

ITEM NO 45 Providing and laying machine cut machine Polished Kota stone flooring 25mm to 30mm thick and required width in plain/ diamond pattern on bed of 1:6 C. M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete. SSR 33.06 / 213

ITEM NO 46 Providing and laying machine cut machine polished machine cut Kota stone slabs 20 to 25 mm thick for treads and risers of steps and staircases, with rounded nosing for the treads on a bed of 1:4 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete. SSR 33.18 / 263

ITEM NO 47 Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with rounded moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. SSR 33.35/216

ITEM NO 48 Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. SSR 33.34 / 216

ITEM NO. 49 Providing and laying rough natural stone tiles 25 mm to 30 mm thick of an approved quality and size for paving / flooring including cement mortar bedding of 25 mm thick in 1:4 proportion, cement float, pointing in cement mortar 1:3, cutting, dressing, leveling, jointing, pointing, curing, finishing etc complete as directed by Engineer In Charge. MCGM/ R3-CS-FL-04 25 to 30 mm thk. rough Kota stone /Sand stone) MCGM/ R3-CS-FL-04-c

ITEM NO 50 Providing and fixing polished natural stone tiles as specified below of approved quality, pattern and colour for dado including preparing the surface and levelling in the desired line, backing of 20 thk. cement mortar in porportion 1:3, square cut top edge or chamfered top edge in cement mortar 1:3, cement float, machine cutting, leveling, jointing, filling the joints with neat cement or pigment mixed with cement, polishing, finishing, curing etc complete as directed by Engineer In Charge. 18mm thk. Jaisalmer Stone/ Yellow Marble MCGM R3-CS-FL-28-i

ITEM NO.51 Providing and laying polished natural stone as specified below (Machine cut) of an approved quality and size for paving /flooring in plain and/or diamond /approved pattern including cement mortar bedding of 25 mm thick in 1:4 proportion, cement float, machine cutting, dressing, leveling, jointing, filling the joints with neat cement slurry or with required pigment, machine polishing at site, curing, finishing, etc complete as directed by Engineer In Charge. 18 mm thk. White marble of superior quality and white cement float MCGM R3-CS-FL-01-e

ITEM NO.52 Providing and laying full body heavy duty, scratch resistant, high abrasion resistant vitrified mirror / glossy/ matt finish tiles for flooring decorative type having size 800 X 800, 1000 X 1000, 800 X 2400 mm (approved size) etc. of 10 to 12 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, approved colour grout, curing and clearing etc. complete. Approved MR

ITEM NO.53 Providing & fixing wood finished Step seating (Pine wood or equivalent- Avg thikness 30 MM), with base of 8 mm thk Marine grade plywood, Wooden flooring to be laid as per pattern and treated properly with sanding, sealer coating, staining & 2 coats of varnish as directed as per detailed drawings. Approved MR

ITEM NO 54 Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete. SSR 33.68/220

ITEM NO 55 Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 mm at weight 0.547 Kilogram/Running metre. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 Kilogram/Running metre. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. And handle section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. and top section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With colour Anodising with box. SSR 39.37 / 251

ITEM NO 56 Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 kg/Rmt. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 kg/Rmt.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section 40 x 18 x 1.25 mm at weight o.417 kg/Rmt. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour Anodising with box SSR 39.41 / 253

ITEM NO 57 Providing and fixing in position aluminium partly openable and partly fixed window of any size as per detailed drawing and as directed by Engineerincharge with all necessary alluminium sections including necessary fixtures and fastening with 5 mm thick float glass etc. complete. a) Without powder coating Note While arriving at the rate of item of item weight at 6.90 Kilogram/Square Metre is considered. SSR 39.54/257

ITEM NO 58 Providing and fixing in position b) Powder Coated aluminium fixed window fully glazed of any size as per detailed drawing and as directed by Engineerincharge with all necessary alluminium sections including necessary fixtures and fastening such as 5 mm thick clear float glass etc. complete. SSR 39.53B/257

ITEM NO 59 Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete. SSR 39.68 / 323

ITEM NO 60 Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete SSR 39.01 / 303

ITEM NO 61 Providing and applying melamine polish of required finish to the wood work by spray machine including knotting and preparing the even surface by scraping, applying French polish , scaffolding if required etc. complete. Note:The work to be executed on prior approval of Superintending Engineer will be necessary SSR 34.09/273

ITEM NO 62 Providing and fixing solid core flush door shutter in single leaf 32 mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete. SSR 39.09 / 246

ITEM NO.63 Supply and Installation of GI DOOR FOR DUCT (0.6 X 1.8MT) AND GLASS (0.3 X 1.00MT) with all the necessary hardware complete as per specification and drawing provided by the Engineer Incharge Approved MR

ITEM NO 64 Providing and fixing stone cladding(Rubble,malad,etc). on external face of the wall, with all the necessary materials along with finish in pigment, including all labour ,etc complete approved MR

ITEM NO 65 Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1 Kg per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete. SSR 31.04 / 205

ITEM NO.66 Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete. SSR.31.26/208

ITEM NO 67 Providing and fixing 20 to 25 mm thick rough shahabad box type waterproofing for basement or underground floor on a base of Cement concrete 1:3:6, including sub base of 2.50 centimeter thick Cement mortar 1:3 with conceal, secrete (RMW), Algae proof or other alike waterproofing liquids, raking of joints upto 35 mm depth, filling the joints with 6 mm size crushed metal, hand grouting with cement slurry, curing and cleaning, with 7 years guarantee on court fee stamp of Rs. 100/- with ponding test etc complete. (excluding Cement concrete 1:3:6 base concrete ) SSR 31.12/253

ITEM NO 68 Providing and fixing 20 to 25 mm thick rough shahabad box type waterproofing treatment to vertical outside faces of Reinforced Cement concrete walls of basement or underground floor including filling the gap of 25 mm between rough shahabad and R.C.C. walls with cement grout mixed with wate proofing liquid Algae proof or other alike with one tile lift method, brushing the joints horizontally with cement slurry mixed with water proofing liquid for width 30 to 35 mm and sloping coping over topmost tile with cement mortar 1:3 butting the bottom most with Cement concrete 1:2:4 mixed with water proofing liquid, curing, with 7 years guarantee on court fee stamp of Rs.100/- with ponding test etc complete. (excluding Cement concrete 1:3:6 base concrete) SSR 31.13/254

ITEM NO 69 Providing preconstructional antitermite treatment as per I.S. 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diametre about 30 -60 cm deep at 15 cm c/c as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on bond paper. SSR 21.25/192

ITEM NO 70 Supply and installation of cubicles of width and depth as perAthena Lite- SS Series Cubicles- Std Sizes (W x D x H): 900 mm x 1550 mm x 2105 mm, (Height is including 100 mm gap from bottom, Door Width- 600 mm specifications/ site drawings). Cubicle height to be 2105 mm. Made from solid grade compact high pressure laminate as per IS:2046 and EN-438 manufactured under high specific pressure > 5 MPa and temperature >120°C, All doors will be of single colour and made of 12 mm thick Merino HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 stainless steel made hinges affixed to the pilasters. Size of panels to be as per drawing. HARDWARE & ACCESSORIES are H shaped (Top) head frame structure made of extruded Aluminium grade 6063 T5-50 micron epoxy powder coated for surface protection, Size to be 125x70x5T. Corner joinery section, Size to be 40x16.5x1.8T. U-Channel Wall joinery section,Size to be 22x16x1.6T. Door stopper section, Size to be 21x12.5x1.6T. Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish to be matt type. Covers to be lacor coated.etc complete. SSR 51.162/504

ITEM NO.71 Supply of hand finish top machine cut, 3 line dressing Cobble Stone in size: 100 x 100 x 100mm in grey colour to be fixed on prepared sub-base with cement mortar 1:4 40 mm thick and cement slurry, filling of joints in C.M. 1:2 with grey cement to match the colour of cobble stone in the required pattern, design and as directed by the Engineer incharge, including cleaning, curing etc. complete as specified and as directed by the Engineer. NOTE: THIS ITEM SHOULD BE OPRATED ONLY AFTER SPECIFIC SANCTION OF DIR(E.S.& P.) or Equivalent. MCGM R3-RW-3-38

ITEM NO.72 Providing & fixing in the footpath Combi- Paver having average crushing strength not less than 80 N/mm² as per technical specifications and IS Code 15658:2006; shot blasted 60mm thick in approved texture and colour and combination size 100 x 200, 125 x 200, 175 x 200, 225 x 200, 275 x 200 to be fixed on average compacted thickness 25 mm well graded sand cushioning uniformly compacted with proper capacity mechanical compactor with required level, grade and camber etc. complete as specified and as directed by the Engineer. NOTE: THIS ITEM SHOULD BE OPRATED ONLY AFTER SPECIFIC SANCTION OF DIR(E.S.& P.) or Equivalent. Approved MR

ITEM NO.73 GRASS JOINT PAVING: Providing and laying machine cut machine polished kota stone flooring for Grass joint paving, 25mm to 30mm thick required width in plain pattern on bed of 1:6 C. M. including cement float, curing, polishing and cleaning including removing unwanted stuff as directed. Excavation for Planting of Lawn Digging of Soft surface up to 30 Cm. as per drawing and specification provided by Engineer In-charge. Approved MR

ITEM NO 74 Stamp Concrete of 100mm Thickness - Providing and Laying in-situ M30 Grade unreinforced plain cement stamp concrete of 100mm thickness pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate (natural sand / VSI grade finely washed crushed sand) Confirming to IS 383, as per mixed in a batching and mixing plant / non tilting mixer and weigh batcher as per approved mix design, admixtures, transporting to site in nagpur city with lead upto 20KM (on Inner Ring Road from Avasti nagar to wadi), spreading, laying with approved make pover, compacted and finished in a continous operation, finishing to lines and grades Also Providing, Placing and applying stamp powder which is light fast UV resistant pigment with appropriate chemical compounds of desired colour on base concrete after excess bleed water has evaporated using dry shake method @5kg per sqm.

Including texturing, and covering with plastic sheet (min 200 micron thickness) and also applying two coats of UV-stable,30 % solidsclear sealer @ 150 to 250 gms per sqm using surface roller and protecting from fallingdust,dirt and curring by curring compound / by providing cement vata in cement Mortor 1:8 @ 0.6m x 0.6m center to center, admeasuring 80mm at bottom and 40mm at top withdepth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-incharge or Landscape architect etc. complete. (prior approval of superinteding Engineer will be necessary ) SSR 54.01 / 513

ITEM NO 75 Providing and casting in situ or precast tapering R.C.C. M-20 Semi Barrier type Kerb with gutter ( as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering Incharge. Using Concrete Batching and Mixing Plant SSR 7.05/69

ITEM NO.76 Providing and fixing corrugated galvanised iron sheets of 0.63mm thick (24 B.W.G.) for roofing without wind tiles including fastening with galvanised iron screws and bolts, lead and bitumen washers as per drawing etc. complete.(Weight of 5.5 kg/sq.m.). SSR 38.04/233

ITEM NO 77 Providing and applying one coat of aluminium paint of approved make to new structural steel work in building and workshop including scaffolding if necessary, cleaning and preparing surface (excluding primer coat) etc. complete. SSR 35.05/223

ITEM NO 78 Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/Square Metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. SSR 40.01 / 264

ITEM NO.79 ACP Cladding: - Providing,aupplying,fabricating and fixing panel of aluminium composite panel cladding in approved shape made out of 4 mm thick ACP sheet material consisting of 3mm thick FR grade mineral core following NBC part IV Fire and life safety (having 2 hours fire resistance in accordance to ASTM E119-12 and BS476 part 6 and 7 class O) sandwitched between two aluminium sheets (each 0.5 mm thick of AA 5005/AA3105 grade) The aluminium composite panel cladding sheet shall be coil coated with kynar 500 based PVDF/Lumiflon based fluropolymer resin (having 70:30 ratio of PVDF and acrylic) coating of approved colour and sg=hade on top face and polymer (service) coating of bottom face as specified using stainless steel screws,nuts,bolts,washers,cleats,weather silicon sealent,backer rods etc .overall weight of the ACP shall not be less than 7.5 Kilogram/Square Metre) SSR 51.100/378

ITEM NO 80 Aluminium Fins:- Providing and Fixing Horizontal fins with 3”x1” Aluminium Tubular Section Powder coated Horizontally with 1” facing and 3” Gap in to in in sections with 1”1” Aluminium Angle powder coated fixed at top and bottom for fixing, with Hardware , with labour inclusive. Approved MR

ITEM NO.81 Aluminium Fins:- Providing and Fixing Horizontal fins with 100 mm x 40 mmx 3 mm thick,(Triangle Concave Shape} Aluminum Angle sections powder coated of specification, distance between section will be 3 -4 inches & details as per drawing, Length and with all the accessories,hardwares, with labour all inclusive. Approved MR

ITEM NO.82 Providing and laying in position terracotta jali(Decorative) of 80 mm thick decorative type as per specification provided by the engineer in charge and drawings including fixtures and fabrications etc complete Approved MR

ITEM NO.83 Dry wall cladding with clay tile; Designing, supplying and fixing of Clay tile of Wienerberger (Red Series or Grey Series) or Equivalent with suitable size and thickness not less than 20 mm as per manufacturer with approved colour and pattern with composition of finest powdered clay and colour mixtures. The clay tile shall be fixed on the suitable framing system by using continuous aluminium profiled section as per manufacturer with suitable size and spacing to withstand the structural design criteria specifled in the technical specification by using necessary HDG brackets, SS316 grade anchor bolts etc as per manufacturer specification. Cladding joints should be with open groove system. with prior approval of concerned Superitending Engineer. SSR 50.25/335

ITEM NO. 84 Providing and fixing in position UV resistant, fire retardant, virtually unbreakable and temperature resistant (-40° C to +130° C) Polycarbonate corrugated sheet of 2mm thickness for roof of approved make to match the roof profile at any height with G.I. J hooks bolts of G.I. clamps nuts & bolts or with self drilling fastener and EPDM washer etc. complete as directed. MCGM R3-CS-RW-08

ITEM NO.85 Providing and fixing 80mm thk. Glass bricks of approved make, size and type in glass block adhesive including filling joints with glass block grout, cleaning etc. complete as directed by Engineer in charge. MCGM R3-CS-FL-19

ITEM NO.86 Casting & fixing Decorative Precast Circular Column,Rectangle Band,Cornice,Window Decorative Sill,Elevational Element Having Precast Shell of thickness 60mm-80m , M25 concrete with approved chemical to have crack free member,including reinforement ,Scaffolding,lifting ,transportation complete Specification provided by the engineer in charge Approved MR

ITEM NO.87 Providing and fixing of factory made uPVC casement window / Fixed Window & Casement Door (White Colour) comprising uPVC multi-chambered frame, Sash, & Mullion with wall thickness of 2.3mm (+-0.2 mm ), duly reinforced with G.I. section 1.5 mm, wherever required. uPVC window & door profile shall be made in India & shall conform to BS EN 12608 and other standards as mentioned below: S.No. Name of the test Test Method Specified Parameter 1 Tensile Impact Strength ISO 8256 - more than 700Kj/m2 2 Vicat Softening Temperature EN ISO – 306 Shall not be < 750C 3 Charpy Impact Strength EN ISO – 179-2 Shall not be < 20KJ/m2 4 Flexural Modulus Elasticity EN ISO – 178 Shall not be < 2200 N/mm2 5 Mean Breaking Stress for welded corner (a) For the tensile bending test EN – 514 Shall not be < 25 N/mm2 (b) For the compression bending test Shall not be < 30N/mm2 6 Heat Reversion Test IS:4985-2000 Shall not be > 2.0 % 7 Surface Spread of flame BS : 476 - Part 7 Classification 1 8 Ignitability Evaluation BS : 476 - Part 5 'P' Not easily ignitable 9 Tensile modulus ASTM D 638 Shall not be < 35 MPa 10 Shear Modulus ASTM D 732 Shall not be < 220 MPa 11 Tensile Strength EN ISO 527 Shall not be < 30 MPa.

All corners of frame and sash will be fusion welded. Mullion shall be welded / screwed. EPDM / TPE Gasket shall be provided in all frame, sash & mullion, wherever necessary.Thereafter, 5 mm Float Annealed glass shall be provided in the sash with the help of uPVC glazing bead and hardware, i.e., friction hinge & single point handle (in window) & 3D Hinges & Multipoint Lock (in door) shall be provided. Window / Door shall be fixed to the wall with 100mm long and 8mm dia. Fasteners and complete in all respect as per direction of Engineer-In-Charge. uPVC Window and Door Profiles are warranted for a period of ten (10) years against non-uniform discoloration, wrapping and rotting under general use. SSR 54.09/517

Casement Window (Big Series) frame of size 67 x 62 mm & Sash / Mullion of size 67 x 78 mm.

Casement Door (Big Series) frame of size 67 x 62 mm & Door Sash of size 67 x 115 mm & Mullion (if required) of size 67 x 78 mm.

Fixed Window (Big Series) frame of size 67 x 62 mm & Mullion (if required) of size 67 x 78 mm.

ITEM NO.88 Providing and fixing 12mm thk toughened etched glass as per the design, as per the design. Glass to be fixed at top & bottom in heavy guage aluminium 'c ' channel concealed in floor & boxing. Cost to be inclusive of silicon sealant to the periphery of the glass as directed MCGM R3-CS-AW-19

ITEM NO.89 SS DUSTBIN Garden 59

ITEM NO.90 SS 202 Grade dustbin double Garden 60

ITM NO. 91 Standard Bench (Refer sketch 14) Product area:1.8 x 0.6 mts, Capacity in nos: 4 nos, Product height:0.80m MCGM GW-3-2-j

ITEM NO.92 Royal Bench (Refer sketch 15) Product area:1.2 x 0.6 mts, Capacity in nos: 3 nos, Product height:0.90m MCGM GW-3-2-k

ITEM NO. 93 Circular tree guard : Providing, fabrication and fixing M.S. Circular tree guard with circular pipe of 10 gauge, 50mm Dia Circular vertical post, 40mm Dia Horizontal support 18mm Dia. intermediate support with M.S. cap- (type-I) logo panel etc. including cutting welding, riveting, oil painting with navy blue colour or any other approved colour shade as directed and fixing in cement concrete foundation including cement concrete paver block lining including removal of surplus material/debris and restoring damaged portion of footpath etc. as directed.(Design details vide Drg.No.4F-A1.1, 4FA1.2, A1.3 in the catalogue of street Furniture (Vol.I) published by B.M.C.) MCGM R3-RT-16-28

ITEM NO.94 Hexagonal tree guard No. tgu- B: Providing, fabrication and fixing M.S. Hexagonal tree guard with circular pipe of 10 gauge, 50mm Dia Circular vertical post, 40mm Dia circular horizontal support, 18mm Dia circular intermediate support with M.S. cap-(type- I) logo panel etc including cutting welding, riveting, oil painting with navy blue colour any other approved colour shade as directed and fixing in cement concrete foundation including cement concrete paver block lining including removal of surplus material/debris and restoring damaged portion of footpath etc. as directed. (Design details vide Drg.No.4F-B1 in the catalogue of street Furniture (Vol.I) published by B.M.C) work complete as per specifications and as directed by the Engineer. MCGM R3-RT-16-29

ITEM NO.95 Square tree guard : Providing, fabrication and fixing M.S. Square tree guard with circular pipe of 10 gauge, 50mm Dia Circular vertical post, 40mm Dia circular horizontal support, 18mm Dia circular intermediate support with M.S. cap-(type-I) logo panel etc including cutting welding, riveting, oil painting with navy blue colour any other approved colour shade as directed and fixing in cement concrete foundation including cement concrete paver block lining including removal of surplus material/debris and restoring damaged portion of footpath etc. as directed. (Design details vide Drg.No.4F-C1 in the catalogue of street Furniture (Vol.I) published by B.M.C) work complete as per specifications and as directed by the Engineer. MCGM R3-RT-16-30

ITEM NO.96 Providing and fixing EPDM (Rubber Mat)(Ethylene propylene diene methylene) flooring for children play area of thickness 25-30 mm above PCC as per specification provided by engineer incharge Approved MR

ITEM NO. 97 Providing and fixing Equipments for children play area, Gym area Etc as per drawings and specification by the engineer in charge Garden SSR

Gym equipment

Forearm twirl

SIT up board

Air walker

8 in 1 combination (chest press+standing twister+surf board+horse rider+leg press+cross trainer+push up bar+aerial stroller)

ITEM NO.98 Providing and laying Natural unpolished White Pebbles of size 30mm to 50mm laying in 3 layers (finish layer of 150mm nominal thickness), graded pebbles etc complete as per drawing as specified as directed by Engineer. (Refer sketch 22) MCGM GW-3-1-c

ITEM NO.99 Providing and laying Natural unpolished mixed colour Pebbles of size 5mm to 20mm laying in 3 layers (finish layer of 75mm nominal thickness), graded pebbles etc complete as per drawing as specified as directed by Engineer. (Refer sketch 24) MCGM GW-3-1-e

ITEM NO.100 Providing and fixing Decorative themed FRP Based Gate (Sports,Musical,Historical Hero,Cultural) entrance of size as specification provided by engineer incharge.complete(5 mt width) Approved MR

ITEM NO.101 Supplying and fixing Stone sculpture/statues of theme upto 1.8 mt ht of approved size and material complete as per specification provided by engineer incharge Approved MR

ITEM NO.102 Providing and erecting chain link fencing 1.6 M. height with G.I. chain link of size 50 x 50 mm, 8 gauge thick and fixed 75 mm above ground level on vertical M.S. Angles of 40 x 40 x 6 mm size, includind excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. c/c with iron bar 16mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25 x 25 x 5 mm size and vertical M.S. flat 35 x 5 mm and 25 x 5 mm horizontal including cross support of 40 x 40 x 6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 mm including 3 coats of oil painting etc. complete. SSR 46.39/298

ITEM NO.103 Providing and fixing thematic murals created in mix media in different shape and size as per required artwork made out of 8mm, 12mm and 19mm thick marine plywood and BTC wood and fibre coating in imported silicon rubber painted MCGM CE4-09-002- FA141C

ITEM NO.104 Artist painting of wall in 3 D format and text format MCGM FAIR-3D-AWP-A

ITEM NO.105 P/f clear acrylic panel of size 350 mm x 250 mm with vinyl cut type and graphics etc MCGM CE4-12-13-A-F-335

ITEM NO.106 P/F MURAL MADE IN FIBRE RAINFORCED PLASTIC AS PER GIVEN ART WORK OF REQUIRED SIZES MCGM CE4-07-076-FF-47A

ITEM NO.107 MURAL IN PAINT (3D) MCGM CE5-10-024- FAIR1

ITEM NO.108 Providing and Fixing Decorative / Ornamental grills as per design for compound wall Fencing including fabricating the grill using M.S. square / round bar, flats and angles including painting with one coat of red oxide zinc chromate primer and two coats of synthetic enamel paint of approved colour and brand etc. complete as directed. MCGM R3-CS-SL-13

ITEM NO 109 Providing and fixing mild steel grill gate as per the detailed drawing including hinges, locking arrangements and painting in three coats of oil paint of approved colour and shade etc. complete.(weight 18 kg. to 20 kg. Per Sq.m.) Spec.No.: As directed by Engineer- in-charge. SSR 23.09/213

ITEM NO 110 Providing and fixing 40mm diameter and 1.5 mm thick Stainless steel hand railing in S.S.304 Grade including fabricating ,fixtures, errecting, necessary welding, grinding, finishing, buffing to stainless steel pipe etc. complete SSR 40.06/329

ITEM NO.111 Double Side Pvc Coated waterproof And Sunshed Tensile Fabric Tensile Roofing including strings and fabrication Specification as per engineer in charge and drawing. Complete with fitings Approved MR

ITEM NO.112 Providing and Fixing laser cut 3-4 mm Acrylic letters of height upto 24 inches with, with all other necessary Hardware for fittings and Labour all Inclusive.including profile LED back lighting .complete Approved MR

ITEM NO.113 Providing and fixing MBMC Logo on entrance gate Approved MR

ITEM NO.114 Providing and fixing stainless steel Name Board on gate/Building including LED backlight complete as per drawing .size (6mx1m) Approved MR

ITEM NO.115 Providing and installation decorative Sculpture, ht of structure - 6ft wide 4 ft ht made of R.S.C.R (Fibre ) material with double PU gloss or matt finished coating with approved design complet as per specification provided by engineer incharge.(Including fabrication) Approved MR

ITEM NO 116 Cutting down trees including trunks and branches with girths above 30cm to 60cm and stacking the materials neatly with all lifts and lead of 1000m. As directed and earth filling in the depression/pit if any. SSR 2.01/23

ITEM NO 117 Cutting down trees including trunks and branches with girths above 60cm to 90cm and stacking the materials neatly with all lifts and lead of 1000m. As directed and earth filling in the depression/pit if any. SSR 2.02/23

ITEM NO 118 Clearing grass and removal of rubbish up to a distance of 50 metres outside the periphery of the area . SSR 2.07/23

ITEM NO 119 Empty boring for 525 to 600 mm dia. bored R.C.C. cast in situ piles including withdrawal of shell, removal of earth to a distance of 50 metres etc. complete. Spec :(As directed by Engineer in Charge) SSR 22.52/171

ITEM NO 120 Empty boring for 725 to 1050 mm dia. bored R.C.C. cast in situ piles including withdrawal of shell, removal of earth to a distance of 50 metres etc. complete. Spec :(As directed by Engineer in Charge) SSR 22.54/171

ITEM NO 121 Providing and laying cast in situ / Ready Mix Cement Concrete M-30 for bored piles each of load capacity and as per design and of 600 mm diameter or as directed placed through steel shells sunk to the required depth through all strata except rock excluding provision of reinforcement as per detailed drawings and design approved by the Engineer-in- charge including placing with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) by tremie arrangements, compaction of concrete including chipping and dressing and withdrawal of shell etc. complete. (Excluding steel reinforcement) SSR 22.29/166

ITEM NO 122 Providing and laying cast in situ / Ready Mix Cement Concrete M-30 for bored piles each of load capacity and as per design and of 750 mm diameter or as directed placed through steel shells sunk to the required depth through all strata except rock excluding provision of reinforcement as per detailed drawings and design approved by the Engineer-in- charge including placing with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) by tremie arrangements, compaction of concrete including chipping and dressing and withdrawal of shell etc. complete. (Excluding steel reinforcement) SSR 22.32/167

ITEM NO 123 Chipping and dressing of the R.C.C. piles upto 0.60 meter including cleaning reinforcement and removal of dismantled materials upto a distance of 50 meter beyond the building area etc. for providing pile caps. Spec :(As directed by Engineer in Charge.) SSR 22.55/171

ITEM NO 124 Providing bentonite slurry process for various diameter of piles vide Item Nos 1 (i to xxiv) above. Spec : (As directed by Engineer in Charge) SSR 22.56/171

ITEM NO 125 Chiseling through pile shells in hard strata like boulders, soft and hard rocks Beyond 550 mm and upto and inclusive of 750 mm dia. including removing and stacking the loose materials etc. complete and disposing of the unserviceable materials outside complete. SSR 22.40 / 169

ITEM NO 126 Chiseling through pile shells in hard strata like boulders, soft and hard rocks Beyond 750 mm and upto and inclusive of 900 mm dia including removing and stacking the loose materials etc. complete and disposing of the unserviceable materials outside complete. SSR 22.41 / 169

ITEM NO 127 Carrying out load test for 1.5 times the proposed safe working load on the pile in driven position above 550 mm and upto 650 mm diameter including construction of test cap, use of accessories and instruments including providing graphs as per I.S. code or Std.Specifications and dismantling the test cap after testing and cleaning the site complete SSR 22.45/170

ITEM NO 128 Carrying out load test for 1.5 times the proposed safe working load on the pile in driven position above 650 mm and upto 750 mm diameter including construction of test cap, use of accessories and instruments including providing graphs as per I.S. code or Std.Specifications and dismantling the test cap after testing and cleaning the site complete. SSR 22.46/170

ITEM NO 129 Carrying out low strain pile integrity test on 300mm / 350 mm / 400mm diameter pile including all arrangements for test, equipments/accessories, materials, labour, submission of test report etc but excluding the cost of installation of job pile (installation of pile shall be paid seperately as per relevent items)all complete as per specification and as directed by the engineer-in-charge. MCGM R3-CS-PLG-14

600 mm MCGM R3-CS-PLG-14.3

750 mm MCGM R3-CS-PLG-14.4

ITEM NO 130 Providing and laying Ready Mix cement concrete M-35 of trap metal for R.C.C. pile caps as per detailed designs and drawings, including bailing out water manually, centering, formwork, laying/ pumping, compacting, finishing and curing etc. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade ) complete.(Excluding steel reinforcement) SSR 22.61 / 172(RA)

ITEM NO 131 Providing and applying plaster / wall punning with plaster of paris ( with plaster of paris material of Ambuja / Mor Chap or equivalent make ) in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc complete SSR 32.30/211

ITEM NO.132 Providing and laying hand made tile of various size and approved designs for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. Approved MR

ITEM NO.133 Providing and fixing in position Gypsum board false ceiling with 12.5 mm thick Gypsum boards, screwed/fixed to the under structure of suspended G.I. Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 mm maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete. SSR 38.51/243

ITEM NO.134 Providing and fixing Modular false ceiling of 600 x 600 mm center to center and 13 mm thick square mineral fiber board to be fixed on frame work of alluminium sections for suspended false ceiling consisting of alluminium T 2”x1 ½” (50 mm x 40 mm) weighing 0.39 Kilogram/m at 60 cms center center and fixed with ½” x ½” (15 x 15 mm) flanges weighing 0.19 Kilogram/m suspended on 6 mm dia mild steel rod weighing 0.22 Kilogram/m, fixed on wall and beams including rounding of the edges with alluinium T of 2” x 1 ½” (50 mm x 40 mm) weighing 0.39 Kilogram/m etc. (all alluminium sections shall be anodized) including all labour, material, lifts etc. complete. SSR 38.52/243

ITEM NO.135 Providing and Fixing Soft Fibre Acoustical Suspended Ceiling System with Optra (Bevelled Tegular) Edge Tiles of size 15mm Exposed Grid. The tiles should have Humidity Resistance (RH) of 95%, NRC 0.9 - 1.0, Light Reflectance ?85%, Colour White, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6 &7) in module size of 600 x 600 x 15mm , suitable for Green Building application, with Recycled content of 66% GW and 74% RW. The tile shall be laid on precoated G.I channel 32 with 15 mm wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm and 600 mm Cross Tees with a web height of 32 mm and a load carrying capacity of 7 Kilograms/M2 with a minimum pull out strength of 100 Kilograms. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system The Tile and Grid system used together should carry a 10 year warranty. products approved as per GRIHA and BS 476 etc. complete SSR 38.47/242

ITEM NO.136 BAFFLE WOODEN CEILING Suspended wood baffles with the help of cables upto 6mm/required MS/GI/Aluminium section from the roof having acoustic properties and Elongated various shape baffles made with High Density Board, Solid Wood Durable Coating, Corrosion Resistant, Tamper Proof with approved Finish material Completed as per specification and drawings as per Engineer in charge Approved MR

ITEM NO.137 Providing and fixing Designer Fabric ceiling with finish Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO.138 Providing and fixing frame work of anodised aluminium sections for suspended false ceiling consisting of aluminium T 50 mm x 40 mm weighing 0.39 Kilogram/m. at 60 cms c/c and fixed with ( 15 x 15 mm) flanges weighing 0.119 Kilogram/m suspended on 6 mm dia. mild steel rod weighing 0.22 Kilogram/m fixed on wall and beams including rounding of the edges with aluminium T of 50 mm x 40 mm weighing 0.39 Kilogram/m etc. including all labour etc. complete. SSR 38.14/234

ITEM NO.139 Providing and fixing in position cement sheet having thickness 12 mm in provided Frame/Brickwall/RCC Member as directed by Engineer in Charge and Drawings . item to be completed in all respect including finishing of joints cut outs, including labour, material, lifts etc. all complete RA SSR 66/528

ITEM NO.140 Providing, fixing transporting and lifting upto 75ft of 80/114 mm corrugated Jinroc Roof Panel: Continuous line Mineralwool / Rockwool insulated corrugated panel having trapezoidal profile with max crest height of 34mm at maximum pitch of 250mm with Top & Bottom 0.5mm TCT PPGI sheet. The stonewool insulation shall be non-combustible grade of density 100 Kg/m3 with permissible tolerance as per IS 8183 and core shall be certified by EUCEB as noncarcinogenic, bio-soluble. The insulation material should be completely non- combustible having class A1 as per EN13501-1, shall have melting point of more 10000C as per ASTM E794; approved by fire test standards UL 723 and ASTM E84, the SDl and FSL value should be 0 as per the UL 723 testing. The Stonewool slab shall be cut into Lamella, rotated & uniformly glued through online oscillation process using PU based glue of reputed make and ensure high adhesive uniformity & proper bonding with sheet. Panel shall be joined together using tongue & groove joinery with max tolerance of 3mm and shall be packed online before the transportation to avoid scratches. The top profiled sheet of 0.5mm TCT PPGI and bottom Micro Ribbed of 0.5mm PPGI.

Sheet shall be of minimum 240 MPa RMP 120 GSM without guard film, 5- 7microns epoxy primer on both side of the sheet and polyester top coat 20-25 micron. The sheet shall have plastic protective guard film of minimum 25 micron to avoid scratches during transportation – Kingspan Jindal. Providing and fixing Flashing for aesthetic and support (girth up to 600 mm) Providing and fixing Gutter (girth up to 900 mm), (PVC nozzle length 300mm) (PPGI - 0.5mm thick). Fire Rated 2 Hr Approved MR

ITEM NO 141 Providing and Fixing Rollar Blinds AMI Make or approved make & shade of 38mm round Aluminium channel with Blackout fabric & telting with chain (Ball) system with all necessary fixtures and fitting etc. complete. (Sample to be final by Engineer In-charge prior execution of work) SSR 51.19/355

ITEM NO.142 Providing and Fixing Vertical Blinds of approved Make and shade of 100mm regular fabric with powder coated aluminium channel with telting PVC chain & bottom weight plate with all necessary fixtures and fitting etc. complete. (Sample to be final by Engineer In-charge prior execution of work) SSR 51.20/355

ITEM NO.143 Providing & fixing Curtains as per drapery details. Including curtain rods & accessories. Spec. As directed by Engineer-In-Charge. Approved MR

ITEM NO. 144 ROLLER BLINDS - COLOUR BACKING Providing & fixing premium quality Roller blinds with prestress Solar protection fabric of high tenacity Polyester Yarn with PVC coating and fungi static treatment and should block the light flux & offer elimination of glare and sunlight /radiance etc. complete. Fabric shall have visible light & solar properties & greengaurd (gold) Indoor Air quality & children & school certified. Fabric composition - 39% Polyester / 61% PVC with alumium backing. Weight - 290 g/sq.m (+/- 5%) Thickness - 0.32 mm (+/- 5%) Fabric openness factor - 3% Tensile strength (warp / weft) - 160/170 daN/5cm Tearing Strength (warp/weft) - 11/13 daN Backing - Aluminium backing. Fungi static treatment - Degree 0 Excellent (EN ISO 846-A) Fire retardancy: B-s2,d0/EN 13501-1, class A/ASTM E84. MCGM - R3-CS-FUR-21

ITEM NO 145 Providing and fixing Internal sinage ss brush finish 2 mm thick Spec. As directed by Engineer-In-Charge. Approved MR

ITEM NO 146 Providing & Fixing of signage using 304 Stainless steel letters for the front & side fascia and 5mm thick acrylic molded letters, for back fascia moulded letters with height 24 inches, with necessary power supplies for connection, including profile LED back lighting Approved MR

ITEM NO 147 Providing and fixing Storage made of 18 mm thk plywood with all external surfaces finished with approved laminate of 1.0 mm thk & all internal surfaces finished with white/offwhite laminate 0.8 mm thk. All wooden surfaces finished with melamine polish. etc complete. Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO.148 MEDIUM HEIGHT STORAGE Medium Height Steel Storage @ 750Lx450Dx1200HT Providing and fixing Openable Steel Storage of 750 x 450 x 1200Ht, with 2 adjustable shelves, Complete body & shutter made in 0.8 mm thick & Top in 2 mm thick CRCA, 2 Shutter to be mounted with the help of cup hinges, and 4 adjustable levelers, enitre storage in powder coated finish with 60 to 80 microns. with 25 mm. thk. as per drawing. SSR 51.36

ITEM NO.149 FULL HEIGHT STORAGE Full Height Steel Storage @ 750Lx450Dx2100HT Providing and fixing Openable Steel Storage of 750 x 450 x 2100Ht, with 4 adjustable shelves, Complete body & shutter made in 0.8 mm thick & Top in 2 mm thick CRCA, 4 Shutter to be mounted with the help of cup hinges, and 4 adjustable levelers, enitre storage in powder coated finish with 60 to 80 microns as as per drawing. SSR 51.37

ITEM NO 150 LOCKERS Multiple Compartment Lockers @ 1140Lx 457D x 1830 mm. Ht. Providing and fixing Multiple Compartment Lockers @ 1140Lx 457D x 1830 mm. Ht. with 12 Compartments , Complete body & shutter made of CRCA Sheet with powder coated finish as per approved color. SSR 51.38

ITEM NO 151 Providing and fixing Podium with acrylic finish Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO 152 Providing and fixing Wall panelling on wall with 12mm thick commercial BWR plywood / MDF mounted on ply support frame work with laser cutting and backlit With LED Finishing includes covering with approved laminate finish the outside of plywood, Teakwood beading at corners, skirting level and false ceiling level, etc. as per drawing. Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO 153 Providing and fixing Wall panelling on wall with 12mm thick commercial BWR plywood / MDF mounted on ply support frame work with laser cutting and backlit With LED Finishing includes covering with approved Veneer finish the outside of plywood, Teakwood beading at corners, skirting level and false ceiling level, etc. as per drawing. Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO.154 Providing & Fixing in position, Acoustical Panelling made from Fabric wrapped Compressed polyester fibre nonwoven 9 mm panels on, 50 x 50 mm sal-wood frame of 600 x 600 c to c having wooden supports from wall of required length, in front of 1000 gsm synthetic wool 50 mm thick with chicken mesh on wall side, including cost of required Cut-Outs, decorative mouldings / finishing-items / paint & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing etc complete SSR 51.01/352

ITEM NO 155 Providing and applying Wallpaper premium Qulaity Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO 156 Providing and supplying Banquet chairs with cushion of approved color. Complete as per specification provided by engineer incharge Approved MR

ITEM NO.157 MID BACK CHAIR Providing and supplying center pivot, revolving, Mid back chair Depth-45cm, width-50cm, height- 105cm to 115cm & seat height- 45cm to 55cm. (+/- 2cm ) with five legged metal / moulded nylon base with push back arrangement. Chairs shall have high density moulded, 360 revolving on suitable base, gas lift , heavy duty twin wheel castors to take min 80 kg/castor with two - pneumatic height adjustment one piece moulded type polypropylene armrest etc. complete. The chair shall be provided with approved tapestry upto Rs 300/m with necessary beading wherever required. All metal work shall be Epoxy Polyster Powder Coated and as directed by Architect in charge. The over all appearance of the product shall be as per photograph. All metal work shall be Epoxy Polyster Powder Coated and as directed by Architect in charge. MCGM R3-CS-FUR-30

ITEM NO 158 HIGH BACK CHAIR Providing and supplying center pivot, revolving, High back chair Depth- 45cm, width-50cm, height- 121cm to 131cm & seat height 45cm to 55cm. (+/- 2cm) with five legged metal /moulded nylon base with push back arrangement. Chairs shall have high density moulded, 360 revolving on suitable base, gas lift , heavy duty twin wheel castors to take min 80 kg/castor with two - pneumatic height adjustment one piece moulded type polypropylene armrest etc. complete. The chair shall be provided with approved tapestry upto Rs 300/m with necessary beading wherever required. All metal work shall be Epoxy Polyster Powder Coated and as directed by Architect in charge. MCGM R3-CS-FUR-29

ITEM NO 159 VISITOR CHAIR Providing and supplying visitor chair having size Depth- 62cm, width-55cm, height-80cm & seat height 45 cm. (+/- 2cm ), having seat & back, shall be made up of 1.2 cm hot pressed plywood, approved tapestry upto Rs.300/m and mould polyurethane foam with P.V.C. lipping all around etc. complete. The chair shall be provided with two one piece armrest made of polypropylene. The chair shall be supported by cantilever type powder coated tubular frame dia 2.54cm x 14 B G M.S.E.R.W. tube. All aluminium steel component shall have Epoxy Polyster Powder Coated. The chair shall be Ergonimc Dry film thickness shall be more than 45 Micron. And as directed by Architect in charge. The over all appearance of the product shall be as per photograph. All metal work shall be Epoxy Polyster Powder Coated and as directed by Architect in charge. MDGM - R3-CS-FUR-32

ITEM NO 160 Public Seating Chair. - 3 Seater Providing and Fixing 3 seater Public seating chair made of complete metal with Legs in Crome finish and seates in silver powder coating finish. SSR 51.44

ITEM NO 161 Providing and fixing 20 mm thick Laminated sheet board pelmet box 150 to 200 mm wide to doors or window frames including 20 mm dia. Aluminium curtain rod with sockets and finishing with french polishing (without top) etc.complete. Spec. As directed by Engineer-In-Charge. SSR:-37.15

ITEM NO 162 Providing & fixing in position Stage flooring Made from 18mm plywood 1200 x 2400 & 18mm Teakwood planks 100 x 800 having tongue & grove on Sal-wood frame of 50 x 100 at 600mm c to c on stage surface including cost of required Cut-Outs, decorative mouldings / finishing-items / polish etc., as per Architectural & Acoustical Design & Instructions & Complete in all aspects. .including all materials labour,finishing etc complete SSR 51.06/353

ITEM NO 163 RECEPTION TABLE Providing and Supplying Reception table of overall size 1650 X 750 X 750 mm made out of 19 mm thick Marine ply (IS 710 : 2010) top Sides and apron having Top and bottom horizontal patta. The table shall be externally and internally finished with 4mm thick group match veneer pattern with grooves including necessary lipping moudling and hardware.5 mm thick thoughened glass modesty shall be provided with 50 X 30 mm BTC wood frame etc. complete. Antitermite treatement to marine ply and all wooden accessories on both sides for full faces before the joineries melamine polish on french polish base coat, hardware as per drawings. etc. all complete as per Architects Drawing. MCGM R3-CS-FUR-23

ITEM NO 164 Providing and fixing Concierge table (3.30 m x 0.75 m + 3.60 m x 0.75 m) - 0 .60 m width for main counter made of 18 mm thk marine plywood including table top, with drawers, shutters main support, internal supports, table top to have frosted glass partition fixed on wooden supports, all external surfaces finished with approved laminate of 1.0 mm thk & all internal supports finished with white/offwhite laminate 0.8 mm thk. All wooden surfaces finished with melamine polish. etc complete.loacation-atrium Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO 165 LOUNGE SOFA Providing and Placing Lounge Chair are made of steel pipe 30 to 35 mm dia of 16 swg. Frame chrome plated, seat & back made of high density foam covered with tapestry approved by E-I- Charge. (Basic rate Rs. 300/- metre.)and having steel arms at the side, available in the following option etc. complete. MCGM R3-CS-FUR-16

3 seater R3-CS-FUR-16-c

ITEM NO.166 Providing and fixing Sofa-3 seater with upholstry (office) Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO.167 Providing and fixing Sofa-2 seater with upholstry . Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO.168 Providing and fixing Sofa-1 seater with upholstry Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO.169 Providing and fixing Full Height Wooden Partitions- Veneer finish made with MR grade Plywood & partly glazed with 10 mm thk toughned glass, nesesary support frames as directed. Finishing complete in all respects with melamine polish to all surafaces & beads, etc. as shown in the drawings. Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO 170 DEMOUNTABLE ALUMINIUM GLASS PARTITION - TYPE 1 Supply and instalaation of Demountable Modular Aluminium Frame Glass Partition, Singlre glazed system compromising of 10mm Toughnend Glass and Aluminium profile Sections of size 75MM x 30MM for fixing at Floor level and at false ceiling level with approximate brackets and expansion bolts of standardised S.S. Finish. All Hardware made of standardised S.S. finish etc. complete. The Profile features and double sided adhesive tape guarantees perfect structural union and sound insulation. Finishes exposed aluminium sections are anodized aluminium finish with 6463 T6 Grade. The Quantity for this item will be the glass panel of height 2100MM only. MCGM R3-CS-FUR-33

ITEM NO.171 Providing & fixing FULL HEIGHT BOTH SIDE LAMINATED PARTITION at required location having height more than 2.8 meter & minimum 77 mm thick made by using 50 x 50 mm (finished size) approved quality seasoned TW section framing at 600 mm center to center,covered with 12 mm marine ply generally confirming to I.S.303 / I.S.710-1980 on both sides.The partitions shall be finished with 1.5 mm thk.approved quality laminate matt/suede/fine line finished lamination pattern with grooves on both sides with necessary lipping (BTC) moulding. Antitermite treatment to plywood and woodwork, door frame including all leads & lifts etc complete as per Architect's Drawing and instructions of Engineer In Charge. MCGM R3-CS-RM-125

ITEM NO.172 Providing and fixing Partly glazed Sliding folding Partition wooden partition with veneer and melamine polish including mechanism Approved RA

ITEM NO.173 Full Height Partitions in Glass finish - Providing and Fixing 80mm to 85mm thick Full height Double Skin partition up to 3 mtr height with All visible sections in Anodized / Powdercoated finish. Made up of Frames and Tiles. Frame construction In combinaton of Aluminium Rails and Bottom ,Center and Top members, Connected with 2 way Round Shape Post , 3way Post , 4 way Post made up of Aluminium Extruded and Tiles in 5mm thk. Non Toughened Glass on both side. With all the Joints in the partitions covered with PVC extrusions to provide better sound Proofing. Tiles to be separated 55mm from each other to provide adequate space for drawing cables for electric, data and telephone with proper facility for fixing electrical and data switch plates. as per design and drawing. SSR 52.5/447

ITEM NO.174 Providing and fixing double/single leaf wooden shutter for partly paneled partly glazed door 35mm without ventilator adopting sections and sizes as given in the standard specifications or as per detailed drawing, including fixtures and fastenings and finishing the wood work with veneer/laminate etc. including mouldings complete. (Without frame) Approved MR

ITEM NO.175 DRESSING TABLE @400LX 400DX 1800H Providing & Fixing Dressing Table of size 400LX 400DX 1800H.The Dressing table unit is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The unit has one drawer and one shelf. The dressing table has a mirror of 4mm thick pasted on 18mm thick prelm particle board attached to the base unit. The mirror size considered is 1155 x 360 x 4(t). The mirror has been pasted using high quality 3M sticker. SSR - 51.56

ITEM NO.176 Providing and fixing Dressing Tables (Size :-0.60 m X .45m ) with 2 sets of drawer & shutter below, made of 19mm thick ply shutters , finished with approved Veneer on all outer faces complete as per drawings and directions. Cost includes provision of approved hinges, door magnets, handles, etc. as per drawings and specifications. Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO.177 WARDROBE WITH MIRROR @ 900LX 600DX 1965H Providing and Fixing Wardrobe with Mirror of size 900LX 600DX 1965H The wardrobe side panels and doors are made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The shelves are made of 18mm thick Prelam Particle Board with decorative laminate on both sides. The top is made of 36mm prelam particle board with decorative laminate on both sides. (18mm Prelam Particle board and 18mm batons on all sides to achieve 36mm overall thickness). The exposed edges of the top are sealed with 2mm thick PVC edge Banding. The top most part of the wardrobe has an aluminum hanger rod of EBCO make. One drawer of size 400(W) x 150(H) x 450 (D) made of 18mm thick prelam Particle Board has been considered. The drawer will have a multipurpose lock of EBCO premium make. The wardrobe handles are Satin SS finish of 160mm pitch. The wardrobe has a multipurpose lock of EBCO make. All hinges considered are Hettich make. Necessary good quality hardwares have been considered as required. SSR NO - 51.57

ITEM NO.178 Providing and fixing netting and in Archery Centre - stops all arrow types. Prevent lost and broken arrows .Extremely low penetration on ultra-thin carbon arrows and carbon arrows with thicker diameters. This backstop netting is delivered in a set complete with plastic hooks, assembly and operating instructions as well as a steel rope coated with PVC.Height: 3 meters (10 feet) (Dimension Tolerance 5%) Length: 4 meters (13 feet) (Dimension Tolerance 5%) Color: greenAccessories: 14 plastic hooks, 4.5-metre steel rope, operating and assembly instructions per specification provided by engineer incharge Approved MR

ITEM NO.179 Providing and Supplying Archery target As per specification and drawing provided by the engineer in charge Approved MR

ITEM NO 180 Providing and Supplying Table for Equipments As per specification and drawing provided by the engineer in charge Approved MR

ITEM NO.181 Providing and fixing Gymnastic Equipment Complete per oylmpic size and standards as per Specification and drawings provided by the Engineer in Charge Approved MR

Iron Gymnastic Spring Board

Vaulting Table Heavy Duty POWDER COATED Steel Base with anti-skid / non-marking pads for floor protection. Top covered by non-slip fabric with reactive foam for improved rebound. Height adjustable

Vaulting BOX Made of seasoned wood and coated with clear PU

Gym Bench - Classic Made of seasoned wood and coated with clear PU

Gymnastic Parallel Bars Heavy Duty POWDER COATED Steel Base with anti-skid / non-marking pads for floor protection. Connection lock allows 360 degree Swivelling, which prohibits rattling & movement. Bars made of fibreglass covered with wood. Height adjustment

Gymnastic Balance Beams Heavy Duty POWDER COATED Steel Base with anti-skid / non-marking pads for floor protection. Height adjustment. Double lock height adjustment system for safety. Top covered with non-slip fabric.

Vaulting Horse Heavy Duty POWDER COATED Steel Base with anti-skid / non-marking pads for floor protection. Top covered by non-slip fabric with reactive foam for improved rebound. Height adjustable.

Pommel Horse Legs are made of heavy steel, pommel made of wood and top made of thick cushion covered with non tearing PVC coated fabric. Height is adjustable.

Uneven Bars Heavy Duty POWDER COATED Steel Base with anti-skid / non-marking pads for floor protection. Bars made of fibreglass covered with wood. Lower bar adjusts Upper bar adjusts from Includes easy adjustable cables with tensioners.

Horizontal Bar Uprights made of Heavy Duty POWDER COATED Steel. Pistons made of Heavy Steel & hot galvanized for longer life. Horizontal bar made of Stainless Steel mounted on column's head. Includes cables. Height adjustable from 175 cm to 285 cm with variation of 5 cm.

Trampoline - Etos

Gymntic Ring Twer

Swiss Ball

BARBELLS WITH various WEIGHT

CLIMBING ROPES (WHITE JUTE)

Wall Bar

Gymnastic Mat Foldable 2-3"

Balance Beam Safety Wrap

COLUMN & CORNER PAD

NON-FOLDING COMPETITION LANDING MAT

Tumbl Trak Gymnastic

Resi-Pit

3/4 SECTION TRAPEZOID TRAINER

ITEM NO 182 Providing and fixing Librarian table (1.8m x .75m)made of 18 mm thk plywood including table top,Side credenza with two drawers, two shutters main support, internal supports, all external surfaces finished with approved laminate of 1.0 mm thk & all internal supports finished with white/offwhite laminate 0.8 mm thk. All wooden surfaces finished with melamine polish. etc complete. Spec. As directed by Engineer-In-Charge. Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO 183 Providing and fixing Issue Counter table (3.05 m x 0.75m) - 0.60 m width for main counter made of 18 mm thk plywood including table top,Side credenza with two drawers, two shutters main support, internal supports, table top to have frosted glass partition fixed on wooden supports, all external surfaces finished with approved laminate of 1.0 mm thk & all internal supports finished with white/offwhite laminate 0.8 mm thk. All wooden surfaces finished with melamine polish. etc complete.loacation- Library area Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO 184 Providing and supplying Book rack straight with white laminate finish inside and exterior designer laminate finish and as shown in the drawings. Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO 185 Providing and supplying standard Reading chairs. as shown in the drawings. Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO 186 Providing and supplying Reading table- Type 01 (size- .075 M x 1.05 M ) - MS frame and made of 18 mm thk plywood including table top all surfaces finished with approved laminate of 1.0 mm thk as shown in the drawings. Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO 187 Providing and supplying Reading table-Type 02 ( (size- 1.50 M x 1.05 M ) - MS frame and made of 18 mm thk plywood including table top all surfaces finished with approved laminate of 1.0 mm thk as shown in the drawings. Approved MR Spec. As directed by Engineer-In-Charge.

ITEM NO 188 Providing and fixing Ledge. (2.10 M x 0.30 m) made of 18 mm thk plywood with veneer finish As directed by Engineer-In-Charge. Approved MR

ITEM NO.189 Providing and installation of square/Circular shape crystal golden/Silver finish TYPE 1 ceiling mount and flush mount chandelier/ LED Chandelier, including fixtures, fittings & scaffolding complete as per specication provided by engineer incharge Approved MR

ITEM NO.190 Providing and installation of square/Circular shape crystal golden/Silver finish TYPE 2 ceiling mount and flush mount chandelier/ LED Chandelier, including fixtures, fittings & scaffolding complete as per specication provided by engineer incharge Approved MR

ITEM NO.191 Providing and installation of square/Circular shape crystal golden/Silver finish TYPE 3 ceiling mount and flush mount chandelier/ LED Chandelier, including fixtures, fittings & scaffolding complete as per specication provided by engineer incharge Approved MR

ITEM NO 192 Supplying and erecting led profile light 12 w conforming IP 65 of any colour with driver complete. Spec. As directed by Engineer-In-Charge. RA

ITEM NO.193 Stainless steel nameplate : Providing and Fixing the 150mmx50mm Stainless steel nameplate as per specification provided by engineer incharge. Approved MR

ITEM NO.194 Supply and installation of digital projector having Full HD 1080p resolution with White and Colour Brightness at range of 3000-4000lm,HDMI port, USB port, AV port, computer port with spring loaded white screen connected with necessary copper mains, required switchgears. complete as per specifcation provided by engineer in charge. Approved MR

ITEM NO.195 Supply and installation of 7000 Lumens Smart 4K UHD HDR Laser Projector, With 3M:1 contrast ratio, With 8.3 mega pixels utilizing 4K UHD (3840 x 2160) resolution, 7,000 ANSI Lumens Brightness. USB port, AV port, computer port with spring loaded white screen connected with necessary copper mains, required switchgears. complete as per specifcation provided by engineer in charge. Approved MR

ITEM NO.196 Providing and fixing European type white glazed earthenware water closet pan with UPVC seat and lid with chromium plated brass hinges and rubber buffers including UPVC and vent pipe up to the outside face of wall 10 litre enameled low level flushing cistern with fittings pipe stop tap brackets for fixing cistern 32 mm dia. UPVC flush pipe with fittings and clamps ,20 mm dia.UPVC overflow pipe ,mosquito proof couplings G.I. chain and pulley,with water Jet and fitting including cutting and making good to the walls and floors testing etc. complete.(prior approval of sample and brand by Ex. Engineer is necessary before use) SSR 43.19

ITEM NO.197 Providing and fixing Orissa type white glazed earthenware water closet pan of size 260mm x 440mm x 580mm with approved make Slim wall hung cistern with installation kit including S or P trap with cast iron soil and vent pipe upto outside face of the wall 1:2:4 brick bat lime concrete bedding without flushing tank and its accessories etc.complete. SSR 48.42/316

ITEM NO.198 Providing and fixing C.P.Two way BIB cock jaquar make or equivalent continental including necessary sockets/union nut etc. complete. SSR 42.80

ITEM NO.199 Providing and fixing 15 mm diameter PVC Aqua kraft type super jet spray with flange 2 in 1 faucet 1.50 metre long including all accessories etc complete SSR 43.39

ITEM NO.200 Providing and fixing White glazed with bottle trap earthenware Wash Hand Basin of 55x40 cm size including cold water piller taps, brackets, rubber plugs and brass chain, stop tap, chromium plate bottle trap and necessary pipe connections including UPAC waste pipe and trap upto the outside face of the wall, making good the damaged surface, testing etc. complete. SSR 41.69

ITEM NO.201 Providing and fixing Oval Type Under Counter Wash Hand Basin of 420 x 590 x 195mm size with pillar cock, C.P.Angular stop cock, long thread of approved make continental including SS bottle trap of necessary pipe connection up to the outside face of the wall, having Telephonic Black / Colour Granite of 180 mm thick fixed on Black Kadappa Framework, etc. Complete as directed by Engineer in charge. SSR 48.35

ITEM NO.202 Providing and fixing C.P. Angular stop cock with wall flange continental (CAT.NO. CON-059) including necessary sockets/union nut etc. complete. SSR 42.79

ITEM NO. 203 Supplying, erecting, testing and commissioning self contained water cooler 230/250 Volts 50 cycles nominal cooling capacity of 150 litres per hour and storage capacity 150 litres with partially stainless steel body as per specification No. AP-WCR/WC CSR 3-3-10

ITEM NO.204 Providing and making ISI Mark ferrule connection of 32 mm dia. to water main including ferrule coupling cast iron bell mouth cover, built in non return valve and fixing including excavation and reinstatement complete. SSR 42.75

ITEM NO.205 Providing and fixing earthenware lipped flat back/corner type Urinal of Hindustan /Perryware / Neycer / Cera or equivalant make with PVC 5 liters flushing system of 5 liters with fittings, inlet pipe with stop tap, brackets for fixing the cistern, 32 mm diameter P.V.C. flush pipe with fitting including lead soil pipe, lead trap & soil pipe connection up to the outside face ofwall. SSR 41.61

ITEM NO. 206 Providing and fixing 10 cm rigid PVC Nahani trap with grating etc. complete as per engineer in charge. SSR 42.67

ITEM NO 207 Providing and fixing on walls/ ceiling/ floor CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

a) 15mm dia SSR 42.55

b) 20mm dia SSR 42.56

c) 25mm dia SSR 42.57

d) 32 mm dia SSR 42.58

e) 40 mm dia SSR 42.59

f) 50 mm dia SSR 42.60

ITEM NO 208 Supplying and erecting ISI mark GI pipe 32 mm dia.‘C’ class at position with accessories complete as per specification no. CW-PLB/GP. CSR 16-5-10

ITEM NO 209 Supplying and erecting ISI mark GI pipe 40 mm dia.‘C’ class at position with accessories complete as per specification no. CW-PLB/GP. CSR 16-5-11

ITEM NO 210 Supplying and erecting ISI mark GI pipe 50 mm dia.‘C’ class at position with accessories complete as per specification no. CW-PLB/GP. CSR 16-5-12

ITEM NO 211 Supplying and erecting 20 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV CSR 13-7-31

ITEM NO 212 Supplying and erecting 25 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV CSR 13-7-32

ITEM NO 213 Supplying and erecting 32/40 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV CSR 13-7-33

ITEM NO 214 Supplying and erecting 50 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV CSR 13-7-34

ITEM NO 215 Supplying and erecting 20/25mm dia gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARV CSR 13-8-13

ITEM NO 216 Providing and fixing 50mm diameter water meter with non-return valve including strainer,sockets/ union nut and including water meter box making locking arrangement and lock. [without chamber] SSR 41.30

ITEM NO 217 Providing and fixing on walls /ceiling/ floor 40 mm dia. uPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. SSR 42.93

ITEM NO 218 Providing and fixing on walls/ ceiling/ floor 50 mm dia. uPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. SSR 42.94

ITEM NO 219 Providing, laying and fixing P.V.C. pipe of 75mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. SSR 42.27

ITEM NO 220 Providing, laying and fixing P.V.C. pipe of 110 mm. dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. SSR 42.28

ITEM NO 221 Providing and making lead joints for 150mm diameter cast iron pipe line including lead and testing. SSR 41.06

ITEM NO 222 Providing and fixing 10 cm PVC nahani trap with grating etc. complete. ( KHURRA) SSR 42.67

ITEM NO 223 Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap SSR 42.02

ITEM NO 224 Providing and fixing Ductile iron manhole cover of light/medium/heavy duty with frameof any size over inspection chamber etc. complete (Prior permission of S.E. is to be obtained before inclusion of this item in the estimate) SSR 50.30

ITEM NO 225 Providing and fixing Ductile iron Man Hole Covers/ Strom Water Grating and Grating with frame of Various sizes, weight and types and load bearing capacity as per EN-124, equivalent NECO with prior approval of concerned Superitending Engineer. SSR 50.85

300 mm wide ( drain channel)

450 mm wide ( drain channel)

ITEM NO 226 Supplying, erecting, testing and commissioning of minimum three & above star rated 3 phase, 415 V, 50 Hz, submersible pump set of 7.5 kW/10HP suitable for erection on open well, pump having delivery head from 60 to 28 m and discharge from 120 to 840 litres per minute & 65 mm suction/50 mm delivery dia. as per specification no. WP-OSP. CSR 12-3-7

ITEM NO.227 Supplying, erecting, testing and commissioning of minimum three & above star rated centrifugal water pump (monoblock), 230 V, single phase, 50 Hz, A.C. supply of 0.375 kW/0.5 HP with discharge 36/9 lpm for head of 6/21 m & 25 mm suction/25 mm delivery pipe on provided CC foundation as per specification no. WP-CGP. Domestic & Flushing Pumps (Flow Rate 70 LPM & 20 M head) CSR 12-1-1

ITEM NO.228 Providing and fixing gun metal Y Strainer confirming to IS and tested to a pressure not less than, including rubber gasket, flanges, unions, nuts, bolts and washer etc complete as required. 25 mm dia SSR Pag NO. 534 ITEM NO 128

ITEM NO 229 Providing and fixing gun metal Y Strainer confirming to IS and tested to a pressure not less than , including rubber gasket, flanges, unions, nuts, bolts and washer etc complete as required. 50 mm dia SSR Pag NO. 534 ITEM NO 124

ITEM NO 230 Providing and fixing gun metal Non Return Valve confirming to IS 778 and tested to a pressure not less than 10 Kg/cm2, including rubber gasket, flanges, unions, nuts, bolts and washers etc complete as required. 50 mm dia SSR Pag NO. 539 ITEM NO 347

ITEM NO 231 Providing and fixing gun metal ball valves confirming to IS 1703 with threaded/flanged joints complete with nuts, bolts, gaskets etc. 50 mm dia SSR Pag NO. 538 ITEM NO 294

ITEM NO 232 Supplying & erecting Float sensor switch for water level controller working on 250V & rated current 8A, with 2 mtr. wire & High quality of wire & plastic body. CSR 12-4-28

ITEM NO 233 Providing and fixing H.D.P container one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres. SSR 42.54

ITEM NO 234 Supplying, erecting, testing and commissioning of automatic control panel for three phase, 415 V, A.C. supply submersible/centrifugal pump set upto 20 HP consisting of star delta starter having relay range 28-42 A, S.P.P., combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated vibration proof enclosure with IP54 protection with single phasing, phase reversal, phase imbalance, etc CSR 12-4-22

ITEM NO 235 Supplying & erecting flat flexible 3 core 4 sq.mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete. CSR 12-4-9

ITEM NO 236 Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL CSR 7-1-27

ITEM NO 237 Supplying and laying (including excavation of suitable width & depth up to 90 cm) 75 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete. CSR 7-6-10

ITEM NO. 238 Supplying and erecting ultra violet water purifier with softener for safe drinking water consisting of UV germicidal tube of 8W capacity, choke made of copper wire, two indicator lamps, dual function cartridge with output of purified water 1 litre/min with activated carbon filter and softener operating on 230 V single phase AC supply with UV fail & filter change indication system. CSR 3-5-2

ITEM NO.239 Supplying & erecting Float sensor switch for water level controller working on 250V & rated current 8A, with 2 mtr. wire & High quality of wire & plastic body. CSR 12-4-28

ITEM NO.240 R.C.C.pipe Np2 class 225mm dia. 2m long SSR PAGE NO- 541 ITEM NO- 854

ITEM NO.241 Providing soak pit of size 120 cm x 120 cm x 120 cm including excavating and filling with brick-bats SSR 42.19

ITEM NO.242 Supplying, erecting, testing & commisioning static energy meter with 240V 50 Hz. AC supply 5 to 30 A, accuracy class 1.0 with backlit LCD display, (measuring and display kWh, kVAh,V, I, PF, frequency, kW, kVA, six months history of energy & MD in kW & kVA) with transparent hinge type box complete erected on polished teak wood board duly wired with required size of weatherproof PVC wires duly tested by electric supply company. CSR 6-5-1

ITEM NO. 243 Supplying & erecting CRCA sheet metal enclosures of 1.2mm thickness with 20A, 2 pin plug & earth socket and 20A, 3 pin plug top with 20A/32A single pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on provided angle iron/GI frame. CSR 5-4-13

ITEM NO.244 Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 6 ways (6 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on provided iron/GI frame as per specification no. SW-MCBDB CSR 5-4-9

ITEM NO.245 Supplying, fixing and commissioning 2 pole RCBO up to 25A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCBO. CSR 5-6-9

ITEM NO.246 Supplying, erecting & marking DP MCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-MCB CSR 5-3-6

ITEM NO. 247 Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 10 ways (10 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection provided on iron/GI frame as per specification no. SW-MCBDB CSR 5-4-11

ITEM NO 248 Supplying, fixing and commissioning 2 pole RCBO 32/40A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCBO CSR 5-6-10

ITEM NO 249 Supplying, erecting & marking SP MCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-MCB CSR 5-3-2

ITEM NO.250 Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable, 1100 V 3 core 4 sq. mm. aluminium conductorcomplete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL CSR 7-1-8

ITEM NO.251 Supplying & erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no. WG-MA/BW CSR 1-3-2

ITEM NO 252 Supplying & erecting mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no. WG-MA/BW CSR 1-3-1

ITEM NO 253 Supplying & erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no. WG-MA/BW CSR 1-3-3

ITEM NO.254 Supplying & erecting mains with 3x10 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no. WG-MA/BW CSR 1-3-9

ITEM NO.255 Supplying & erecting mains with 4x16 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no. WG-MA/BW CSR 1-3-10

ITEM NO.256 Supplying & erecting HMS PVC conduit 20mm dia. with necessary accessories in wall/floor with chiselling appropriately as per specification no. WG-MA/CC. CSR 1-1-7

ITEM NO.257 Supplying & laying HMS PVC conduit 20mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification no. WG-MA/CC. CSR 1-1-8

ITEM NO.258 Supplying & erecting HMS PVC conduit 25mm dia. with necessary accessories in wall/floor with chiselling appropriately as per specification no. WG-MA/CC. CSR 1-1-9

ITEM NO.259 Supplying & laying HMS PVC conduit 25mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification no. WG-MA/CC. CSR 1-1-10

ITEM NO.260 Supplying & erecting HMS PVC conduit 32mm dia. with necessary accessories in wall/floor with chiselling appropriately as per specification no. WG-MA/CC. CSR 1-1-11

ITEM NO.261 Supplying & laying HMS PVC conduit 32mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification no. WG-MA/CC. CSR 1-1-12

ITEM NO.262 Supplying and erecting integrated LED Bollard Cylindrical / Cubical shaped 500mm 8W IP65 & IK10 class having extrusion aluminium housing with polycarbonate diffuser, having system lumens output of Min. 800 Lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6500K, THD0.90, operating range of 140-240V, inbuilt surge protection of 2 kV, Life class of 25,000 Hrs. at L50B50, including driver complete with minimum 2 Year warranty as per specification No FG-ODF/BL CSR 2-3-19

ITEM NO 263 Supplying and erecting integrated LED Bollard Cylindrical / Cubical shaped 800mm 8W IP65 & IK10 class having extrusion aluminium housing with polycarbonate diffuser, having system lumens output of Min. 800 Lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-240V, inbuilt surge protection of 2 kV, Life class of 25,000 Hrs. at L50B50, including driver complete with minimum 2 Year warranty as per specification No FG-ODF/BL. CSR 2-3-20

ITEM NO.264 Supplying and erecting LED square / circular Max. 14 W down lighter / Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 1500 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED. CSR 2-1-4

ITEM NO. 265 Supplying and erecting integrated LED street light fitting 23 to 25W IP65 & IK08 class having single piece pressure die-cast aluminium housing, having system lumens output of Min. 2300 Lumens, min. efficacy of 100 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs at L70B50 including driver complete with minimum 2 Years warranty as per specification No. FGODF/ SL. CSR 2-3-2

ITEM NO.266 Providing & erecting 3 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL CSR 8-2-9

ITEM NO.267 Supplying & erecting watertight terminal box of 1.6 mm (16 gauge) CRCA sheet of size 200 x 150 x 150 mm. complete on pole as per specification No. CB-SB CSR 7-8-2

ITEM NO.268 Supplying and erecting LED Strip light Max. 45 W IP20 class having minimum lumens output of 800 Lumens/m, min. efficacy of 90 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD<10%, p.f. >0.95, operating range of 230-270V, Life class of 30,000 Hrs at L70B50 including driver with minimum 1 year warranty as per specification No. FG-IDF/LED.(IP Rated Out Door Quality) CSR 2-1-10

ITEM NO.269 Supplying LED concealed type foot / step light with aluminium body for indoor / outdoor application suitable for 4W - 6W LED including driver and erecting by making necessary arrangement / recess in wall to make it flush with surface with minimum 1 year warranty as per specification No. FG-IDF/LED. CSR 2-1-12

ITEM NO.270 Supplying & erecting integral post top lantern fixtures (mushroom type) suitable for LED lamp upto 12 W consisting of clear acrylic top cover, cast aluminium pole cap complete with accessories on provided pole /bracket as per specification no. FG-ODF/PTL. CSR 2-4-3

ITEM NO.271 Supplying & erecting integral post top lantern fixtures (globe type) suitable for LED lamp upto 12 W consisting of aesthetic round clear acrylic top cover, cast aluminium pole cap on provided pole /bracket as per specification no. FGODF/ PTL.(Fixed on ground/Walls ) CSR 2-4-4

ITEM NO.272 LED type Solar street light fixtures with heat sink for LED, crystalline/ polycrystalline silicon solar PV modules,suitable size of maintenance free battery along with 5.5 mtr , 65mm dia GI pole with civil foundation, base plate, nut , bolts etc and all accessories required for completing installation as per specification. MCGM R3-ME-5-6 Solar street light of 24 Watt LED MCGM R3-ME-5-6-e

ITEM NO.273 Supplying and erecting Gate / garden light fitting with 200mm dia. Glass bowl suitable for upto 12W LED Lamp on provided pipe as per specification No. FG-ODF/GLT. CSR 2-4-1

ITEM NO.274 Supplying and erecting Gate / garden light fitting with 300mm dia. Glass bowl suitable for upto 12W LED Lamp on provided pipe as per specification No. FG-ODF/GLT. CSR 2-4-2

ITEM NO. 275 Supplying and erecting CRCA powder coated light LED fitting (4 feet) Max. 33W with high transitivity diffuser with system lumens output of Min. 4000 lumens, min. efficacy of 120 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., Ripple0.95, operating range of 120-270V, surge protection of 4 kV, Life class of 50,000 Hrs at L70B50 , IP20 rated including driver with end caps on provided PVC Block / wooded board with minimum 2 years warranty as per specification No. FG-IDF/LED. CSR 2-1-19

ITEM NO. 276 Supplying and erecting LED square / circular Max. 7W down lighter / Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 770 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED CSR 2-1-2

ITEM NO. 277 Supplying and erecting integrated LED flood light fitting Max. 155W IP65 & IK07 class having pressure die-cast aluminium housing, having system lumens output of Min. 18600 Lumens, min. efficacy of 120 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs at L70B50 including driver with U shaped bracket with minimum 2 Years warranty as per specification No. FGODF/ FL. CSR 2-3-17

ITEM NO.278 Supplying and erecting integrated LED flood light fitting Max. 195W IP65 & IK07 class having pressure die-cast aluminium housing, having system lumens output of Min. 23400 Lumens, min. efficacy of 120 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs at L70B50 including driver with U shaped bracket with minimum 2 Years warranty as per specification No. FGODF/ FL.(Beam Type) CSR 2-3-18

ITEM NO.279 Light fixtures complete with: a) All fixing accessories, mounting Brackets etc. necessary for completeness of installation. b) Lamp of specified wattage c) Electronic ballast of suitable capacity as per specification SITC of Direct light outdoor floodlight Colour temperature [K]: 3000 MCGM R3-ME-4-1-i

ITEM NO.280 Light fixtures complete with: a) All fixing accessories, mounting Brackets etc. necessary for completeness of installation. b) Lamp of specified wattage c) Electronic ballast of sutable capacity as per specification SITC of IP67 linear surface-mounted LED luminaire. Extruded Hshaped aluminum profile. MCGM R3-ME-4-3-f

ITEM NO.281 SITC of IP67 flexible 24 V linear LED stripColor temperature (CCT) MCGM R3-ME-4-34-h

ITEM NO. 282 Supplying and erecting Energy Saving Ceiling fan of 3 star rating as per BEE 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF CSR 2-9-19

ITEM NO.283 Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1400 mm, Max. Energy Consumption of 28W having service ratio (CMM/W) of Min. 8, PF>0.9, THD<10% with IR remote control, Temperature Rise of Max. 40 deg.C, having external mounted control PCB completely erected in position as per specification no. FG-FN/CF. CSR 2-9-23

ITEM NO 284 Supplying and erecting electronic type step regulator for ceiling fan 600/ 900/ 1200/ 1400 mm. sweep, complete erected on provided switch board CSR 2-10-9

ITEM NO 285 Supplying and erecting fan hook box of 10 mm M.S. round bar bounded to the R.C.C. bars upto 50 mm length each side and pierced through a 16 S.W.G. thick aluminium/M.S. Bowl 100 mm dia. or equivalent square size and having depth upto 75 mm complete erected with duly painted by one coat of red oxide paint and two coats of paint erected in position and without any leakage of slurry of cement concrete on either side of the box and positioned to the bottom level of the slab. CSR 2-10-5

ITEM NO 286 Supplying and erecting ‘B’ class G.I .pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire. CSR 2-10-6

ITEM NO 287 Point wiring for ceiling fan concealed type in min 20 mm HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification no. WG-PW/CW CSR -1-7-6

ITEM NO 288 Point wiring for light/bell concealed type in min 20 mm HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification no. WG-PW/CW CSR 1-7-5

ITEM NO 289 Point wiring for independent plug, concealed type in min 20 mm HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wires, modular type switch and socket, earthing and required accessories as per specification No WGPW/ SW CSR 1-7-7

ITEM NO 290 Point wiring for independent plug, concealed type in min 20 mm HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wires, modular type switch and socket, earthing and required accessories as per specification No WG?PW/SW CSR 1-7-7

ITEM NO 291 Supplying & erecting CRCA sheet metal enclosures of 1.2mm thickness with 20A, 2 pin plug & earth socket and 20A, 3 pin plug top with 20A/32A single pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on provided angle iron/GI frame. CSR 5-4-13

ITEM NO. 292 Supplying and erecting modular type switch 6A/10A on provided plate and box with wiring connections complete CSR 1-6-1

ITEM NO. 293 Supplying and erecting modular type switch 16A on provided plate and box with wiring connections complete CSR 1-6-2

ITEM NO 294 Supplying and erecting shockproof 3 pin plug socket 6A with porcelain base/flush type erected on filled polypropylene board or polished thick varnished double wooden block / folded or screwed board with top of either wooden/3mm thick hylam sheet/ 4mm thick plywood pasted with 1.5mm thick laminate with S M screws and duly connected. CSR 1-5-3

ITEM NO 295 Supplying and erecting shockproof 3 pin plug socket 16A with porcelain base/flush type erected on filled polypropylene board or polished thick varnished double wooden block / folded or screwed board with top of either wooden/3mm thick hylam sheet/ 4mm thick plywood pasted with 1.5mm thick laminate With S M screws and duly connected. CSR 1-5-4

ITEM NO 296 Supplying and erecting modular type 3 pin 6/16A multi socket with safety shutter on provided plate and box with wiring connections complete. CSR 1-6-11

ITEM NO.297 Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 8 module duly erected flush to wall with required chiselling and finishing with cement morter / POP as per required to match the background in an approved manner. CSR 1-6-39

ITEM NO.298 Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 1 module duly erected flush to wall with required chiselling and finishing with cement morter / POP as per required to match the background in an approved manner. CSR 1-6-34

ITEM NO.299 Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement morter / POP as per required to match the background in an approved manner. CSR 1-6-35

ITEM NO.300 Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement morter / POP as per required to match the background in an approved manner. CSR 1-6-36

ITEM NO.301 Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement morter / POP as per required to match the background in an approved manner. CSR 1-6-38

ITEM NO.302 Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement morter / POP as per required to match the background in an approved manner. CSR 1-6-40

ITEM NO.303 Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 16 / 18 module duly erected flush to wall with required chiselling and finishing with cement morter / POP as per required to match the background in an approved manner. CSR 1-6-41

ITEM NO 304 Supplying and erecting ceiling rose/ batten holder/ slanting holder/ hanging cord switch/ hanging bell push/ pendant holder bakelite base 6A erected on filled polypropylene board or polished double wooden block/ PVC junction box. CSR 1-5-5

ITEM NO. 305 Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU CSR 7-2-31

ITEM NO.306 Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU CSR 7-2-32

ITEM NO.307 Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU CSR 7-2-34

ITEM NO.308 Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 3½ core 35 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL CSR 7-1-16

ITEM NO.309 Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 3 core 25 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (Wire Armoured) CSR 7-1-12

ITEM NO. 310 Supplying, erecting, testing & commissioning of 3 kVA capacity on line pure sine wave,PWM,IGBT based UPS with 0.8 to unity output pf ,single phase input & 1 phase output complete with all protections as per specification no. AP-UPS (Without batteries) CSR 3-7-3

ITEM NO.311 Supplying and erecting 12 V/100Ah SMF battery with battery terminal wire, duly charged complete with 24 months warranty complete. for 30 mins battery backup CSR 3-8-12

ITEM NO 312 Supplying & erecting mains with 3x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no. WG-MA/BW CSR 1-3-7

ITEM NO. 313 Supplying and erecting GI earth conductor of required sizes used for earthing or any other purposes on wall with necessary GI clamps fixed on wall/cable/ conduit with screws complete CSR 9-2-5

ITEM NO. 314 Supplying, installing and testing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all accessories of copper materials & recording the results as per specification no. EA-EP CSR 9-1-2

ITEM NO. 315 Supplying, installing and testing pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.I. Rod complete with all accessories of GI materials & recording the results as per specification no. EA-EP CSR 9-1-4

ITEM NO. 316 Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU CSR 7-2-32

ITEM NO 317 Supplying, installing, testing and commissioning of 1 kWp OFF-GRID solar power pack with interconnecting wires / cables up to 12 V pure sine wave solar power inverter (THD<3%), SPV Modules (335 WP X 03 Nos.), C-10rated lead acid battery bank 12 V, 400 Ah / (12V, 100 Ah x 4 nos.) suitable for4 Hours backup with suitable MS powder coated stand to hold battery bank andkeeping sufficient space for filling distilled water, canopy box to house inverter and other electronics, wiring up to solar inverter in casing and capping, displayboard, sign board , two distinct earthing, spike type lightning arrester, necessaryaccessories complete with 5 year ON-SITE warranty and fully comprehensive maintenance contract as per specification no. ESD-RT-OFG CSR 4-4-1

ITEM NO.318 Supplying, erecting, testing and commissioning of diesel generating set with alternator of 10 kVA output continuous rating, 3 phase, 415 V, 50 Hz, 0.8 p.f., A.C. supply a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %, with performance class G2/G3 and maximum fuel consumption of 2.4 ltr/hr @75% loading. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads, with standard control panel comprising of meters, switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA sheet, sound absorbing material to restrict sound level up to 75 dB at 1.0 m, provided with first filling of oil, diesel not less than 40 ltr etc., on provided M20 grade CC foundation as per specification No. GEN-DG CSR 11-1-3

ITEM NO. 319 Supplying, erecting, testing and commissioning of microprocessor based AMF panel suitable for diesel generating set of upto 10 kVA capacity single/three phase, 230/415 V, 50 Hz, A.C. supply with all standard features, safeties etc as per specification no. GEN-AMF. CSR 11-2-1

ITEM NO 320 Supplying, installing, testing & commissioning of 8/10 Ch. Network Video Recorder (NVR), suitable for 2 MP cameras only with HDMI/VGA outputs provided HDMI output of 4K resolution or VGA output with output up to 1920x1080. Support H.265 or higher, H.264, MJPEG, Incoming Bandwidth 80Mbps with minimum 2 SATA Hard Disks, ANR Technology, 2 SATA interfaces for 2 HDDs and capacity of each HDD up to 8TB, minimum 02 USB port, Alarm I/O 4/1, RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface, support multi brand network Cameras, ONVIF conformance, Multiple network monitoring: Web viewer . support protocol TCP/IP, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™, HTTPS. RoHS, UL, CE, FCC certified. duly erected in provided U Rack with wiring connections, tagging and programming etc complete as per specifications no. CCTV-NVR CSR 19-6-12

ITEM NO. 321 Supplying & erecting of High definition 4/5 Megapixel IP IR Bullet Camera with following features Image Sensor : minimum 1/2.8" Progressive Scan CMOS, Video Resolution : minimum 2592 x 1520 Video Compression : H.264, H.265 or higher, at least Three individually configurable stream, Frame rate : minimum 25 fps at all resolutions, WDR : minimum 120 dB Wide Dynamic Range, ONVIF profile conformant, minimum IR distance : 50m, Lens Type : 2.8/4/6 mm Lens, fixed focal, Field of View : 2.8 mm, horizontal FOV 107°, vertical FOV 57°, diagonal FOV 129° 4 mm, horizontal FOV 86°, vertical FOV 47°, diagonal FOV 102° 6 mm, horizontal FOV 55°, vertical FOV 29°, diagonal FOV 65° Lux sensitivity - minimum 0.2 Lux at color, minimum 0.05 Lux at Black & White, 0.0 Lux (IR) Night Vision Distance minimum IR - 50m. Camera minimum Adjustment Angles - Pan : 350°, Tilt : 72°, Rotate : 350°. Power Supply : Support 12VDC & PoE, IP67, IK10 - Vandal Resistant. Built in micro SD/SDHC/SDXC card slot of minimum 128 GB, Built in microphone. minimum Input/Output - Audio in × 1, Audio Out × 1, Alarm in × 1, Alarm Out × 1. Image Settings : Rotate mode, saturation, brightness, contrast, sharpness, gain, white balance. Image Enhancements : Day/Night-Auto (ICR)/Color/Black & White, 3D Digital Noise Reduction, Automatic White Balance, Automatic Gain Control, Backlight Compensation, Highlight Compensation. CSR 19-6-2

Events : Privacy Masking, Motion detection, Scene change detection, Face capture, Video tampering, audio exception detection, Region entrance detection, Region exiting detection. Operating temperature ( -30 to 60° C ) . Security - User account and password protection, HTTPS, IP filter, IEEE 802.1X, digest authentication, user access log, TLS1.2, AES - 256, SSH/Telnet closed, FTP disabled. Protocol - DHCP, UDP, HTTP, HTTPS, NTP, DNS, RTP, RTSP, SMTP, SSL/TLS, TCP/IP, Secure Real-Time Transport Protocol (SRTP), Bonjour, SNMP and Secure shell (SSH) supported protocol. RoHS, WEEE, ISO-14001 and REACH compliant, UL/EN OR equivalent BIS/TECH/STQC or any indian standards as applicable, CE, FCC certified. duly erected in position on wall/ceiling/false ceiling/provided pole (mounting height not more than 5 meter) etc with all accessories etc complete as per specification no. CCTV-CAM

ITEM NO. 322 Supplying and installing FR PVC sheathed HDPE insulated copper cat-6 cable with rodent proof and anti termite jacket suitable for networking compliant with ANSI/TIA-568.2-D standards in provided conduit/casing-ncapping as per specification no. WG-ELVC/NC CSR 19-3-6

ITEM NO. 323 Supplying and fixing 3 m 24 AWG multi stranded, UTP patch cord of enhanced cat 6A type, compliant ANSI/TIA-568.2-D standards in position as per specification no. WG-ELVC/PC CSR 19-3-21

ITEM NO. 324 Supplying, erecting & terminating 15 m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19pin HDMI connectors complete. CSR 19-1-24

ITEM NO. 325 Supplying & erecting 32" professional LED Monitor with 1920*1080 (Full HD) Display, suitable for 16 channel NVR and following features Brightness: minimum 250 Cd/m2 Contrast Ratio: minimum 1000:1 Viewing angle: 178/178 deg. Response time: maximum 8 ms Inputs: HDMI, VGA, BNC, USB, Audio In, Built-in speakers maximum 2 W, Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc. complete as per specifications no. CCTV-MON CSR 19-6-23

ITEM NO. 326 Supplying and fixing Cat 6, 24 port patch panel with keystone jacks compliant with ANSI/TIA/EIA 568.C.2 & ISO/IEC 11810 complete as per specification no. WG-NAS/PP CSR 19-5-4

ITEM NO.327 Supplying and erecting stainless steel single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV CSR 13-7-36

ITEM NO.328 Supplying and installing wall mounting swinging hose reel drum fitted with 19 mm dia. 30m long high pressure polypropylene (Polyhose) alongwith necessary accessories complete as per specification no. FF-FFA/HV CSR 13-8-2

ITEM NO.329 Supplying and erecting stainless steel branch pipe 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specifications no. FF? CSR 13-8-8

ITEM NO.330 Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP CSR 13-6-8

ITEM NO.331 FIRE BOOSTER PUMP: Supplying, installation, testing and commissioning of booster fire pump [BP] suitable for water discharge of 450 LPM at 35 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 5.5 kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal/vertical type, single/multi stage, centrifugal casing pump of cast iron body & bronze/CI impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/BP CSR 13-3-1

ITEM NO.332 Supplying and erecting 75/80 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV CSR 13-7-23

ITEM NO.333 Supplying and erecting 75/80 mm dia Cast Iron end line strainer of Y-type flanged end pattern, PN16 pressure rating, SS screen, end connection with Flanged / Screwed / Socket Weld / Butt Weld End etc with standard OAR (open area Ratio) for positive suction complete as per specification no. FF-VL/ELS CSR 13-7-5

ITEM NO.334 Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV CSR 13-7-20

ITEM NO.335 Suppling & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete. CSR 13-14-1

ITEM NO.336 PUMP STARTER: Supplying, erecting, testing and commissioning of D.O.L Starter suitable for 400 V, 3 phase 50 Hz with no volt coil and overload element with necessary materials and connected to supply for above 7.5 HP 10 HP. CSR 12-4-3

ITEM NO.337 Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable 1100 V, 3 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU CSR 7-2-16

ITEM NO.338 Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU CSR 7-2-33

ITEM NO.339 Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.3TR to 1.6TR capacity having ISEER minimum 5.00 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. AP-AC/ SAC CSR 3-2-11

ITEM NO.340 Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.7TR to 2.0TR capacity having ISEER minimum 3.8 to maximum 4.39 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. AP-AC/ SAC CSR 3-2-12

ITEM NO.341 Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 16mm complete. CSR 3-2-27

ITEM NO.342 Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 16 mm for solar water heater /AC system. CSR 4-2-4

ITEM NO.343 Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 12mm complete. CSR 3-2-26

ITEM NO.344 Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 12 mm for solar water heater /AC system. CSR 4-2-3

ITEM NO.345 Supplying and erecting HMS PVC conduit FRLS grade 20 mm dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC. CSR 1-1-7

ITEM NO.346 Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 19 mm for solar water heater /AC system. CSR 4-2-5

ITEM NO.347 Supplying, erecting, testing & commissioning fresh air intake system, ductable circular inline fresh air fan inlet unit having 300cfm capacity with maintaining the static pressure minimum 20mm suitable to operate on 1 phase, 230V, 50Hz, A.C. supply complete. Toilet Exhaust Fans CSR 3-11-60

ITEM NO.348 Supplying, erecting, testing & commisioning GI sheet 0.6 mm (24 SWG) having zinc coating of 275 microns with galvanization process compliance to IS 2629:1985 to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint as per specification no. CP/SH/CR CSR 6-1-2

ITEM NO.349 Supplying & erecting 22 SWG G.I sheet metal cawl sector shaped with 25 x 25 x 3 (mm) angle iron frame, metal mesh to avoid birds entry with necessary material, suitable for exhaust fan of 300 mm as per specification no FG-FAS/MSC CSR 2-10-14

ITEM NO.350 Supplying and erecting aluminium powder coated linear grill of suitable size for width length without collar dampers having matching colour with the existing false ceiling and suitable for deflection of 15/30/45°. CSR 3-11-88

ITEM NO.351 Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU CSR 7-2-15

ITEM NO.352 Providing adhesive thermal insulation for supply return air duct with 19mm nitrile rubber insulation having R-value as per the prevailing provisions in ECBC- 2007. Underdeck Insulation CSR 3-11-83

ITEM NO.353 Supplying and erecting iron work, sheet metal work consisting of MS sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the site engineer. CSR 6-1-19

ITEM NO.354 Supplying, erecting, testing and commissioning of 18HP, VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47° C, non stop cooling even at 56° C and coefficient of performance (COP) 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000 metre operation in cooling mode with inverter/ digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete. CSR 3-11-7

ITEM NO.355 Supplying, erecting, testing and commissioning of 16HP, VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47° C, non stop cooling even at 56° C and coefficient of performance (COP) 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000 metre operation in cooling mode with inverter/digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete. CSR 3-11-6

ITEM NO.356 Supplying, erecting, testing and commissioning of 14HP, VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47° C, non stop cooling even at 56° C and coefficient of performance (COP) 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000 metre operation in cooling mode with inverter/digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete. CSR 3-11-5

ITEM NO.357 Supplying, erecting, testing and commissioning of 12HP, VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47° C, non stop cooling even at 56° C and coefficient of performance (COP) 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000m operation in cooling mode with inverter/digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete. CSR 3-11-4

ITEM NO.358 Supplying, erecting, testing and commissioning of 10HP, VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47° C, non stop cooling even at 56° C and coefficient of performance (COP) 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000m operation in cooling mode with inverter/digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete CSR 3-11-3

ITEM NO.359 Supplying, erecting, testing and commissioning of 7HP to 8HP, VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47° C, non stop cooling even at 56° C and coefficient of performance (COP) 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000m operation in cooling mode with inverter/digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete. CSR 3-11-2

ITEM NO.360 Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette room/indoor unit (IDU-compact / standard size) of nominal cooling capacity 3.0TR (1100 cfm) to 3.2TR (1165 cfm) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for costal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation. CSR 3-11-22

ITEM NO.361 Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette room/indoor unit (IDU-compact/standard size) of nominal cooling capacity 2.0TR (618 cfm) to 2.3TR (671 cfm) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for costal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation. CSR 3-11-20

ITEM NO.362 Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette room/indoor unit (IDU-compact/standard size) of nominal cooling capacity 1.5TR (512 cfm) to 1.8TR (618 cfm) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for costal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation CSR 3-11-19

ITEM NO.363 Supply, installation, testing and commissioning of VRV / VRF based ductable type, high static room/indoor unit (IDU) having nominal cooling capacity of 8.0TR (3200 cfm) having EER as per BEE standards and specifications with evaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, in built drain pump, expansion device, cordless remote control with necessary controls and electrical terminal to receive power supply, etc. having anti-corrosive coating suitable for costal area and decorative slim dimension suitable for ceiling suspended arrangement with an electronic control console and any additional refrigerant and oil charge as per requirement during installation complete. CSR 3-11-56

ITEM NO.364 Supply, installation, testing and commissioning of VRV / VRF based ceiling suspended 8.0TR (6600 cfm) to 10.0TR (8200 cfm) Treated Fresh Air (TFA) (5380 cfm) room/IDU with evaporator fan with motor, copper tube, aluminium fin evaporator coil, washable air filter, insulated drain tray, in built drain pump, expansion device, cordless remote control with necessary controls and electrical terminal to receive power . having anti-corrosive coating suitable for costal area with decorative slim dimension suitable ceiling suspended arrangement and an electronic control console with any additional refrigerant and oil charge as per requirement during installation complete. 1236 CFM / 8.0TR CSR 3-11-59

ITEM NO.365 Supply, installation, testing and commissioning of VRV / VRF based ceiling suspended 6.5TR Treated Fresh Air (TFA) (5380 cfm) room/IDU with evaporator fan with motor, copper tube, aluminium fin evaporator coil, washable air filter, insulated drain tray, in built drain pump, expansion device, cordless remote control with necessary controls and electrical terminal to receive power . having anti-corrosive coating suitable for costal area with decorative slim dimension suitable ceiling suspended arrangement and an electronic control console with any additional refrigerant and oil charge as per requirement during installation complete. 988 CFM / 6.0TR CSR 3-11-58

ITEM NO.366 Supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 41.3mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. CSR 3-11-89

ITEM NO.367 Supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 34.9mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. CSR 3-11-90

ITEM NO.368 supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 28.6mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. CSR 3-11-91

ITEM NO.369 supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 22.2mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiation with OEM standards of VRV/VRF air conditioning system complete. CSR 3-11-92

ITEM NO.370 Supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 19.1mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. CSR 3-11-93

ITEM NO.371 supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 15.9 mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. CSR 3-11-94

ITEM NO.372 supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 12.7mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. CSR 3-11-95

ITEM NO.373 supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 9.5mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. CSR 3-11-96

ITEM NO.374 supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 6.4mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete. CSR 3-11-97

ITEM NO.375 Supplying and installation of high pressure grade required size copper connection Y or T- Joints/refnut complete erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc. with brazing and testing for leakages confirming the normal operation of the VRV/VRF air conditioning system. CSR 3-11-86

ITEM NO.376 Providing and fixing on walls/ ceiling/ floor 50mm dia.CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. SSR 42.60

ITEM NO.377 Providing and fixing on walls /ceiling/ floor 40mm dia.CPVC pipe with necessary fittings,remaking good the demolished portion etc. complete. Pipeline if necessar yand conveying and stacking the same in PWD chowky or as directed etc. complete. SSR 42.59

ITEM NO.378 Providing and fixing on walls/ ceiling/ floor 32mm dia.CPVC pipe with necessary fittings,remaking good the demolished portion etc. complete. Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. SSR 42.58

ITEM NO.379 Providing and fixing on walls/ ceiling/ floor 25mm dia.CPVC pip ewith necessary fittings,remaking good the demolished portion etc. complete.Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. SSR 42.57

ITEM NO.380 Supplying, erecting, testing & commisioning GI sheet 0.6 mm (24 SWG) having zinc coating of 275 microns with galvanization process compliance to IS 2629:1985 to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint as per specification no. CP/SH/CR CSR 6-1-2

ITEM NO.381 Supplying, erecting, testing & commisioning GI sheet 0.8 mm (22 SWG) having zinc coating of 275 microns with galvanization process compliance to IS 2629:1985 to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint as per specification no. CP/SH/CR CSR 6-1-3

ITEM NO.382 Supply, fabrication, installation an testing of flexible canvass connections constructed between ductable unit/dampers/ducting of suitable size with fire resist flexible double canvas sleeve complete. CSR 3-11-82

ITEM NO.383 Providing adhesive thermal insulation for supply return air duct with 19mm nitrile rubber insulation having R-value as per the prevailing provisions in ECBC 2007. CSR 3-11-83

ITEM NO.384 Providing and applying of acoustic insulation for air ducts with 25mm thick, 48kg/cu.m fiber glass faced with RP tissue and covered with 26SWG perforated aluminium sheets complete. CSR 3-11-84

ITEM NO.385 Supplying, installing and testing of 25 mm thick underdeck insulation. Insulation material shall be Closed Cell Elastomeric Nitrile Rubber. Thermal conductivity of insulation material shall not exceed 0.035 W/(m.K) at mean temperature of 0°C as per EN 12667. Moisture Diffusion Resistance Factor or ‘µ’ value of insulation material shall be minimum 7,000 without any external barrier as per EN 12086. The insulation shall have fire performance such that it passes Class 1 as per BS476 Part 7 for surface spread of flame as per BS 476 and also pass Fire Propagation requirement as per BS476 Part 6 to meet the Class ‘O’ Fire category as per 1991 Building Regulations (England & Wales) and the Building Standards (Scotland) Regulations 1990 The insulation material shall have fire performance of V0, HB as per UL 94, 1996. Material should be FM (Factory Mutual), USA approved. The insulation material shall be dust and fibre free. Approved MR

ITEM NO.386 Supplying and erecting aluminium powder coated linear grill of suitable size for width length without collar dampers having matching colour with the existing false ceiling and suitable for deflection of 15/30/45°. CSR 3-11-88

ITEM NO.387 Supply, installation, testing and commissioning of volume control box with collar for control damper of required sizes in GI construction with operating mechanism, mounting arrangement, rubber refrigerant kits etc. complete. CSR 3-11-81

ITEM NO.388 Supplying and installing of collar damper of galvanised iron material of upto 120 microns for anti corrosive resistance for supply air grill of suitable size. CSR 3-11-87

ITEM NO.389 Supply, installation, testing and commissioning of Extruded Aluminium Construction powder coated Jet nozzle (201-400 cfm) Approved MR

ITEM NO.390 Supply, installation, testing and commissioning of Extruded Aluminium Construction powder coated Jet nozzle (401-600 cfm) Approved MR

ITEM NO.391 Supply, installation, testing and commissioning of Extruded Aluminium Construction powder coated Jet nozzle (601-800 cfm) Approved MR

ITEM NO.392 Aluminium Extruded Fresh Air & Exhauast Rain Protection Air Louvers with Bird screen Approved MR

ITEM NO.393 Supplying and erecting iron work, sheet metal work consisting of MS sheets,various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the site engineer.(FOR OUT DOOR UNIT) CSR 6-1-19

ITEM NO.394 Supplying, erecting, testing and commissioning centralised programmable remote control panel (HMI) touch manager controls minimum 16 system of 64 ODU's can be controlled and up to 992 IDU's can be individually mounted and controlled indoor units having colour min 200mm size LCD touch panel, yearly schedule, power proportional distribution function, temperature limitation, history function complete erected on wall integrated with provided fire alarm system. CSR 3-11-79

ITEM NO.395 Supplying, erecting, testing & commissioning fresh air intake system, ductable circular inline fresh air fan inlet unit having 300cfm capacity with maintaining the static pressure minimum 20mm suitable to operate on 1 phase, 230V, 50Hz, A.C. supply complete. CSR 3-11-60

ITEM NO.396 Supplying, erecting, testing & commissioning fresh air intake system, ductable circular inline fresh air fan inlet unit having 1000cfm capacity with maintaining the static pressure minimum 20mm suitable to operate on 1ph, 230 V, 50Hz, A.C. supply complete. CSR 3-11-61

ITEM NO.397 Supplying and erecting exhaust fan heavy duty 230 V A.C. 50 cycles 450 mm. 900 RPM complete erected in position as per specification no. FG-FN/EXF CSR 2-9-17

ITEM NO.398 Supplying and erecting exhaust fan heavy duty 230 V A.C. 50 cycles 450 mm. 1400 RPM complete erected in position as per specification no. FG-FN/EXF CSR 2-9-16

ITEM NO.399 Supplying and erecting PVC insulated PVC round sheathed FR 1 sq.mm (32 no. x 0.20mm dia.) 3 core flexible multi stranded copper industrial cable for voltage grade up to 1.1 KV ( Control cable) CSR 1-3-13

ITEM NO.400 Supplying ande recting HMSPV Cconduit 20mmdia.with PVC accessories on wall / ceiling as per specification no. WG-MA/CON. CSR 1-2-3

ITEM NO.401 Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU CSR 7-2-32

ITEM NO.402 Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU CSR 7-2-33

ITEM NO.403 Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU CSR 7-2-34

ITEM NO.404 Providing & erecting hot dipped galvanised perforated type cable tray manufactured from16SWG GI sheet of 300mm width & 75mm height complete with necessary coupler plates & hardware. CSR 7-11-8

ITEM NO.405 Providing & erecting hot dipped galvanised perforated type cable tray manufactured from16SWG GI sheet of 150mm width & 75mm height complete with necessary coupler plates & hardware. CSR 7-11-6

ITEM NO.406 Supplying 6A 3 pin plug top bakelite type of 230V A.C. supply. CSR 1-5-14

ITEM NO.407 Supplying, erecting, testing & commissioning fresh air intake system, ductable circular inline fresh air fan inlet unit having 300cfm capacity with maintaining the static pressure minimum 20mm suitable to operate on 1 phase, 230V, 50Hz, A.C. supply complete. CSR 3-11-60

ITEM NO.408 Supplying, erecting, testing & commissioning fresh air intake system, ductable circular inline fresh air fan inlet unit having 1000cfm capacity with maintaining the static pressure minimum 20mm suitable to operate on 1ph, 230 V, 50Hz, A.C. supply complete. CSR 3-11-61

ITEM NO.409 Supplying and erecting SS enclosure of 1.6mm thick with detachable gland plate suitable for upto 100A MCCB. CSR 5-11-17

ITEM NO.410 Supplying, erecting & commissioning 4 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB. CSR 5-6-5

ITEM NO.411 Supplying, erecting & commissioning 4 pole RCCB 16/25A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB. CSR 5-6-4

ITEM NO.412 Supplying, erecting & commissioning 4 pole RCCB 63A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB. CSR 5-6-6

ITEM NO.413 Supplying & erecting single compression type brass cable glands for 2 to 4 core 2.5 sq mm /2 to 4 core 4 sq mm /2 core 6 sq mm cable as per specification No. CB-GL CSR 7-7-1

ITEM NO.414 Supplying & erecting single compression type brass cable glands for 3 to 4 core 6 sq mm /2 to 4 core 10 sq mm cable as per specification No. CB-GL CSR 7-7-2

ITEM NO.415 Supplying & erecting single compression type brass cable glands for 3 to 4 core 16 sq mm /3 to 4 core 25 sq mm /3 core 35 sq mm cable as per specification No. CB-GL CSR 7-7-3

ITEM NO.416 Supply, installation, testing and commissioning air curtain of 6feet width having air throw velocity of 21 m/sec, low noise level up to 38 to 46dBA suitable for door height upto 9feet, working on 1 phase, 230V, 50Hz, A.C. supply. CSR 3-11-76

ITEM NO.417 Supply, installation, testing and commissioning air curtain of 4feet width having air throw velocity of 21m/sec, low noise level up to 38 to 46dBA suitable for door height upto 9feet, working on 1 phase, 230V, 50Hz, A.C. supply. CSR 3-11-75

LANDSCAPING

ITEM NO.418 Preparing Lawn (30 cm. depth):- Excavating the ground to a required depth of 30cms, removing & conveying unwanted stuff to a required distance as directed. Filling fresh garden soil/silt & manure in excavated area in 3:1 proportion to a height of 30cms. Mixing garden soil and manure thoroughly well, leveling, and watering on previous night. Planting required variety of lawn grass as directed and maintaining till well established by watering, weeding, elinning rolling etc complete PARK AND GARDEN DSR

ITEM NO. 419 Preparing flower Bed:-Excavating the ground to the required depth of 30cms, Removing and conveying unwanted stuff to a required distance as directed, Filling fresh garden soil & manure in excavated area in 3:1 proportion to a required height of 30cms Mixing garden soil and manure thoroughly well, leveling, watering, on previous night. Planting seedlings of required annuals 25cms apart Maintaining till well established by watering. weeding, Stirring replacing of casualties etc, Complete. PARK AND GARDEN DSR

ITEM NO 420 GARDEN SOILSupplying on site garden soil well sieved 90% to pass through IS. sieve of 10 mm size free from stones rubbish like dried grass roots and other such materials. The soil should be fresh from quarry. The color of the soil generally is red. The soil will be measured by measuring box. (Farma) Item includes royalty charges, octroi, corporation Tax Transporting loading -unloading etc (Lead charges per 90 km. considered) PARK AND GARDEN DSR .

ITEM NO.421 FARM YARD MANURE:-Supplying on site well decayed, well dried, well powdered, without clods and free from stones, dried grass and other rubbish material. The color of the manure generally is black. The manure will be measured by measuring box.(Farma)Item includes Transporting, loading -unloading etc (Lead charges per 30 kom. are considered) PARK AND GARDEN DSR

Plant should be healthy ,well rooted ,diseased free and free from any pest attack with sufficient moisture around root zone in pollybag. (Wherever applicable)

ITEM NO.422 Sapling of small & medium Ornamental flowering plants, Ornamental ficus, Mussanda etc. Thuja, Cupresus, Common Ornamental Shrubs for Shrubbery PARK AND GARDEN DSR

ITEM NO.423 Palm Varities (Red Palm, Fox Tail Palm, Bottle Palm, Rhaphis Palm, Table Palm, Cristal Palm etc.) 6-8Ft PARK AND GARDEN DSR

ITEM NO.424 Plants required for Landscaping: (Euphorbia, Hemelia, Malpbegra, Mussanda, Ticoma, Song of India, Golden Bamboo, Buddhas Bamboo, Goiden Ficus, Phonicus Palm X'mas Tree, Ficus Panda etc.) 4-5 ft PARK AND GARDEN DSR

ITEM NO. 425 Preparing Shrubbery - Excavating the ground to required depth of 30cms, removing and conveying unwanted stuff to a required distance as directed. Filling fresh garden soil & Manure in excavated area in 3:1 proporation to a height of 30cms. Mixing garden soil & manure thoroughly well, leveling, and watering on previous night, planting well developed shrubs plant 0.5 Mtrs. apart as directed and maintaining till well established by watering, weeding, stirring, replacing casualties etc. complete. PARK AND GARDEN DSR

ITEM NO. 426 Forrest Trees (Peltophorum,Bakul,Kecia,Neem,Tabobia,ETC) Annex B(8-10 FEET) PARK AND GARDEN DSR

ITEM NO. 427 Trimming of trees having girth between 2' to 5' MCGM R3-GW-8-2

ITEM No.428 Plant Protection measures for tree having girth between 2'to 5' MCGM R3-GW-8-22

ITEM NO.429 Quisqualis 24indica 6 “ to 9 “ height excluding pollybag MCGM R3-GW-5-205

ITEM NO. 430 Bougainvillea purviana Thimma 6 “ to 9 “ height excluding pollybag MCGM R3-GW-5-20

ITEM NO.431 Codieum variegatum Hybrid croton 6 “ to 9 “ height excluding pollybag MCGM R3-GW-5-37

ITRM NO. 432 Samanea saman Rain tree 4' to 5 ' height excluding pollybag MCGM R3-GW-5-295

ITEM NO. 433 Roheo discolor Rhoeo Nana 4" to 6" height excluding pollybag MCGM R3-GW-5-145

ITEM NO. 434 Roheo discolor Rhoeo Tall 4" to 6" height excluding pollybag MCGM R3-GW-5-146

ITEM NO.435 Delonix regia Gulmohar 4' to 5 ' height excluding pollybag MCGM R3-GW-5-261

ITEM NO.436 Verbena 6 “ to 9 “ height excluding pollybag MCGM R3-GW-5-158

ITEM NO.437 Chlorophytum laxum Dwarf Chlorophytum 6 “ to 9 “ height excluding pollybag MCGM R3-GW-5-40

ITEM NO.438 Chlorophytum comosum Spider Plant 6 “ to 9 “ height excluding pollybag MCGM R3-GW-5-39

ITEM NO.439 Mangifera indica Mango 4' to 5 ' height excluding pollybag MCGM R3-GW-5-284

Shreeji EPC Pvt Ltd (BID ID -6316307)