REPAIR/REPLACEMENT OF ROOF, JOINERY, PLASTERING, PLUMBING AND CONNECTED WORKS AT 162 MH AT DINJAN MIL STN UNDER GE DINJAN

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding, (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

S&F for glazed ceramic coloured tiles of 300x200x7mm thick tiles on vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match, over backing coat of in cement mortar (1:4) 10mm thick complete all as specified and as directed.

S&F for glazed ceramic coloured tiles of 450x350x7mm thick tiles on vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match, over backing coat of in cement mortar (1:4) 10mm thick complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06Sqm but not exceeding 0.11Sqm (400x400x7mm) in floor, over 15mm thick screed bed or bedding in cement mortar (1:6) on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11Sqm but not exceeding 0.18Sqm (400x400x7mm) in floor, over 15mm thick screed bed or bedding in cement mortar (1:6) on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete all as specified and as directed.

M&L for granite work (table rubbled and polished) in steps, jambs, pillars, window-cills, cooking platforms etc. over 15mm thick screed bed or bedding in cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Demolition of unreinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for 15mm thick rendering on sunken floor in cement mortar (1:3) with water proofing compound and finished even and smooth with out using extra cement complete all as specified and as directed. Note : WPC will be measured and paid separately.

M&L for applying a coat of blown type bitumen evenly @ 1.50 Kg per Sqm and blinding with clean dry sand @ 0.05 Cum per Sqm complete all as specified and as directed.

M&L for cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

M&L for 40 mm thick, plain cement concrete (1:2:4) type B-1 (using 12.50 mm graded stone aggregate) with WPC as sub base as in floors and finishing the surface even and smooth without using extra cement complete all as specified and as directed.

S&F in repairs vitreous china squatting pan "orissa" pattern size 580mmx440mm white with integral foot rests including inlet, ball valve float chain and pull and brackets, flush pipe of polyethylene of low or high density or PVC 32mm dia for low level cistern complete all as specified and as directed.

S&F for 110mm PVC (SWR) WC connector with lip ring complete all as specified and as directed.

S&F in repairs PVC flushing cistern of 10 ltr capacity high level with intel ball valve float chain and pull back brackets and 32 mm PVC flush pipe complete all as specified and as directed.

S&F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and flushing pipe, anti syphonic pipe with PVC seat and cover complete but excluding flushing cistern & flush pipe including making good damaged/disturbed surfaces complete all as specified and as directed. Make : Cat No. C0287/0288 of Parryware/Hindware/Cera.

S&F for vitreous China urinal, flat back of size 440X360X270mm, white (minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete complete as specified and as directed. Make : Cat No. C0501 of Parryware/Hindware/Cera.

S&F in repair, brass cast copper alloy, chromium plated shower rose 125mm size with shower arm 15mm size, 195mm long fixing to steel pipe or to unions complete all as specified and as directed.

S&F in repair, brass chromium plated tubular towel rail, D type, 60cm long, 20mm dia with brackets complete all as specified and as directed.

S&F in repair, soap dish vitreous china coloured approximate suze (160X160X90mm) complete all as specified and as directed.

S&F in repairs, 15 mm bore, stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

M&L for cutting chases not excceeding 10cm girth to brick or concrete wall, for concealed water tubing, pinning in, making good to facings where required and pointing in cement mortar (1:3) and to ends or edges of landings, steps,cills, sunshades, shelves, lintels etc. complete all as specified and as directed.

Fixing only stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repair 15mm bore, PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and as directed.

S&F in repairs, vitreous china wash basin, size 550x400mm, white, flat back, with PVC waste pipe, CP waste coupling, chain, plug and porcelean stopper & backets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and as directed. Make : Cat No. C0406 of Parryware/Hindware/Cera.

S&F in repair 15 mm bore, pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F in repairs, 15 mm bore, bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

Taking up or down 15 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for re-use at same site or other site complete all as specified and directed.

Taking up or down 20 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for re-use at same site or other site complete all as specified and as directed.

Taking up or down 25 mm to 32 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for re-use at same site or other site complete all as specified and as directed.

S&F for 16mm of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in tranches complete all as specified and as directed.

S&F for 20mm of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in tranches complete all as specified and as directed.

S&F for 25mm of CPVC pipes SDR 11& Plain CPVC SDR 11 fittings in tranches complete all as specified and as directed.

S&F for 16mm dia CPVC brass threaded elbow complete all as specified and as directed.

S&F for 16mm dia CPVC brass threaded Tee complete all as specified and as directed.

S&F for 20 mm CPVC brass threaded union complete all as specified and as directed.

S&F for 25 mm CPVC threaded union complete all as specified and as directed.

S&F for 25 mm CPVC ball valve complete all as specified and as directed.

S&F for 25mm tank adopter complete all as specified and as directed.

Supply, laying, connection and testing, 15mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures complete fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Supply, laying, connection and testing, 20mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239(Part -2):2011 and fixtures complete fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Supply, laying, connection and testing, 25mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239(Part -2):2011 and fixtures complete fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Demolition of reinforced cement concrete in any description including cutting reinforcement as required to facilitate demolition of concrete complete all as specified and as directed.

M&L for reinforced cement concrete 1:2:4, type B-1 (nominal mix) (Using 20 mm graded stone aggregate) as in slabs supported on wall, roof beams etc complete all as specified and as directed.

M&L for use & waste form work to soffits and sides of roof slabs for flat rough finished surfaces of concrete complete all as specified and directed.

M&L for TMT steel bars 10mm dia and over, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for TMT steel bars 6 to 8mm dia, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

Dismantling of rotational moulded polyethylene water tank of capacity exceeding 250 litres but not exceeding 500 Ltrs complete all as specified and as directed.

Dismantling of rotational moulded polyethylene water tank of capacity exceeding 500 litres but not exceeding 1000 Litres complete all as specified and as directed.

Dismantling of rotational moulded polyethylene water tank of capacity exceeding1000 litres but not exceeding 2000 Litres complete all as specified and as directed.

S&F for 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe complete all as specified and as directed.

S&F for 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe complete all as specified and as directed.

S&F for 2000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe complete all as specified and as directed.

S&F for in repair 20 mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for brick work using locally available first class bricks sub class 'B' bricks (old size brick), straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) complete all as specified and as directed.

M&L for plain cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in coping etc including form works complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

M&L for rendering 10 mm thick in cement mortar (1:4) on concrete surfaces as in ceilings (sunshed, chajja, fins etc), roof projection and finishing surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar (1:6) on other than fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar (1:4) on other than fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for preparing new plastered surfaces of walls, etc and applying two coat of cement base paint over a coat of alkali resistant priming paint complete all as specified and as directed.

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

S&F in repair 75 mm dia outlet and minimum 50mm water seal, PVC (SWR) floor trap, with grating including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc area not exceeding 10Sqm on plan and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading in layers not exceeding 25cm, levelling, watering and well ramming as in soft/loose soil complete all as specified and as directed.

Removing excavated material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

S&F for 110 mm bore, PVC (SWR), Type 'B', soil waste and vent pipes in any length without ears, with rubber ring joints laid in trenches, floor or fixed to wall complete all as specified and as directed.

M&L for plain cement concrete (1:4:8) type D-2 (using 40 mm graded broken stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete for 110 mm bore drain pipe complete all as specified and as directed.

S&F for 75 mm bore, PVC (SWR) bends of any radius complete all as specified and as directed.

S&F for 110 mm bore, PVC (SWR) bends of any radius complete all as specified and as directed.

S&F in repairs PTMT(half or full threaded) waste coupling 40mm for sink (min weight 32mm - 45gms/40mm - 60gms) complete all as specified and as directed.

S&F in repairs 32mm brass chromium plated bottle traps for wash basins with inlet and uotlet screwed for pipe or connections including necessary packing, union and cap all as directed.

S&F for grating doom, circular type, 100mm dia of PTMT, (mimimum weigh 25 gms) complete all as specified and as directed.

S&F in repairs, coloured, toilet paper holder of vitreous china, box type fixed to wall with chromium plated brass screw complete all as specified and as directed.

S&F for plastic water closet seat, back, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

S&F in repairs 15 mm bore, stop valves (concealed type), cast copper alloy, chromium plated, long sunk and cup, screwed down, high pressure, with capastan head, screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F for 110 mm bore, PVC (SWR) bends with acess door of any radius complete all as specified and as directed.

S&F in repair 110 mm bore, PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed.

S&F for 75 mm bore, PVC (SWR), Type 'B', soil waste and vent pipes in any length without ears, with rubber ring joints fixed to wall using mild steel holder bat for rain water, etc complete all as specified and as directed.

S&F in repair 125/110 mm dia outlet and minimum 50mm water seal, PVC (SWR) gully trap, with grating including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

S&F for 75 mm bore, PVC (SWR) bends with acess door of any radius complete all as specified and as directed.

S&F for 75 mm bore, PVC (SWR) branch pieces, double (double Y) equal or unequal all as specified and as directed.

S&F in repairs new magnum (combo set) white coloured urinal port size 380x400x590 complete all as specified and as directed. Make : Cat No. C0583 of Parryware/Hindware/Cera.

S&F for syntex tank cover for 500/1000/2000 ltr complete all as specified and as directed.

M&L for 25 mm thick, plain cement concrete (1:2:4) type B-0 (using 12.5 mm graded stone aggregate) as in floors & finishing the surfaces even & smooth with using extra cement complete all as specified and as directed.

M&L for water proofing treatment on RCC roof etc. comprising with the following operation and as specified herein below complete all as specified and as directed:- (a) Taking down existing old tarfelt, bituminous compound including cleaning and removing debris to a distance exceeding 100m and not exceeding 250m. (b) 15 mm thick plastering in cement mortar (1:4) finished even & smooth. (c) Preparing & cleaning of fully dried cement plastered surface. (d) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 liters per sqm conforming IS-3384 (e) A layer of APP based polymeric membrane membrane 3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyster non woven fabric (weighing not less than 160 gms/sqm) shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction. (f) One coat of aluminium paint over the APP based membrane @ 0.11 Kg/Sqm

M&L for forming V grooves in plaster not exceeding 10mm deep and not exceeding 10mm on face complete all as specified and as directed.

Disconnecting existing water tank of capacity exc 250 litres & n.exc 500 litres, reconnecting and refixing in position including cleaning and removing all scale and dirt, etc from tank and from mouth of circulating pipes etc complete all as specified and as directed.

Disconnecting existing water tank of capacity exceeding 500 litres and not exceeding 1000 litres, reconnecting and refixing in position including cleaning and removing all scale and dirt, etc from tank and from mouth of circulating pipes etc complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness including cover fillets and frame work any type complete all as specified and as directed.

S&F for aluminium Anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frame including providing two coats of oil bound distemper complete all as specified and as directed. Make of E-Board : Eternit Everest / lafarge/ Armstrong/Visaka Industries Ltd.

Taking down chowkats or frame, not exceeding 1.5 Sqm in each with shutters (without taking off shutter from the frame) complete all as specified and as directed.

Taking down chowkats or frames, exceeding 1.5 Sqm but not exceeding 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and as directed.

Taking down shutters of any description not exceeding 1 Sqm each complete all as specified and as directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and as directed.

S&F for pressed steel frames for doors local work shop made of size 105x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

S&F for pressed steel frames for doors local work shop made of size 125x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

S&F for well seasoned second class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

M&L for palin cement concrete (1:3:6) type C-1 (Using 20mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

S&F for mild steel small articles using flat iron of size 25x6mm thick such as band, strap, hold fast, cleat, support, hook, hinges, base tie for door frame etc and other similar items conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

M&L for palin cement concrete (1:2:4) type B-0 (Using 12.5mm graded stone aggregate) as in anchorging hold fast, bed plate and benching for manholes etc. complete all as specified and as directed.

Refixing of old servicieable shutters of any description in existing location/opening not exceeding 1 Sqm each including resecuring or easing and adjusting complete all as specified and as directed.

Refixing of old servicieable shutters of any description in existing location/opening exceeding 1 Sqm but not exceeding 2 Sqm each including resecuring or easing and adjusting complete all as specified and as directed.

M&L for 35mm thick timber plain, framed, panelled shutters (any number of panels), with panels of 12mm thick veneered particle board medium density with commercial face veneers: supplied and fitted to chowkats, sizes/section of members of shutters shall be as specified in SSR Part I, Section -8, clause 8.24 (a) complete all as specified and as directed..

S&F for 30 mm thick flush door shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides with internal jointless lipping not less than 25 mm depth complete all as specified and as directed.

S&F for 30 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded as specified in SSR Part I Section 8 clause 8.24 (b) complete all as specified and as directed..

M&L for 35 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded as specified in SSR Part I Section 8 clause 8.24 (a) complete all as specified and as directed..

S&F for solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified and as directed.

S&F for aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm anodised finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and as directed.

S&F for 150 mm long, aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and as directed.

S&F for 100 mm size, butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F for 100 mm long, stainless steel butt hinges fixed with stainless steel hinge pin etc complete all as specified and as directed.

S&F for 150 mm size, aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and as directed.

S&F for 100 mm long, aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and as directed.

S&F for 75 mm size, butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F for 100 mm size, aluminium anodised handles, fabricated type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and as directed.

S&F for 150 mm size, aluminium shutter/gate hook and eye, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and as directed.

S&F for galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples including timber bead complete all as specified and as directed.

S&F in repairs galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples including timber bead complete all as specified and as directed.

S&F for anodised aluminium frame for doors, windows, ventilators with one or more rebates including necessary joining cleat for fixing etc. complete all as specified and as directed.

M&L for anodised aluminium door shutters, using aluminium section weighing not less than 0.55Kg per metre including necessary joining cleats, glazing clips, rubber neoprene packing, aluminium handles 2 numbers in each shutter, hinges, anodised aluminium snap beading, screws etc complete all as specified and as directed.

M&L for anodised aluminium window and ventilator shutters, fixed type, with or without sash bar, using aluminium section weighing not less than 0.55Kg per metre including necessary joining cleats, glazing clips, rubber neoprene packing, aluminium handles 2 numbers in each shutter, hinges, anodised aluminium snap beading, screws etc complete all as specified and as directed.

M&L for mild steel framed work such as grills, gratings, gates etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

M&L for double action floor spring hydraulicallyregulated, made up of minimum 1.25mm thick aluminium alloy sheet box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed.

S&F in repairs 100mm, vertical type 4 levers brass mortice lock complete all as specified and as directed.

S&F in repairs mild steel 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or steel frames, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

S&F for 3 mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for 3 mm thick, figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for 6.3 mm thick, sheet glass, ordinary quality and glazing with oil putty in square exceeding 0.5 Sqm in each pane complete all as specified and as directed.

M&L for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of new or previously untreated steel surfaces of any description, not otherwise described over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and as directed.

S&F in repairs curtain/harrison rails, 20mm dia, mild steel, chromium plated with fixing brackets, stops, rollers, etc complete all as specified and as directed.

M&L for providing pelmet boxes in repair using 12 mm thick particle board, medium density, flat pressed, single layer type with BWR type adhesive, fixed with screws complete all as specified and as directed.

S&F for cast iron (extruded section body) door closer hydraulically regulated, designation No.3, universal type suitable for shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed.

M&L for one coat of white wash on old decorated surface of wall and cornices after brooming, scrapping down with steel scapper smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots etc. complete all as specified and as directed.

M&L for one coat of white wash on old decorated surface of ceiling after brooming, scrapping down with steel scapper smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots etc. complete all as specified and as directed.

M&L for two coats of cement base paint over a coat of alkali resistent primer including preparation of old decorated surface of walls complete all as specified and as directed.

M&L for one coat of cement base paint on old decorated surface of wall and cornices after brooming, scrapping down with steel scapper smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots etc. complete all as specified and as directed.

M&L for one coat of oil emulsion distemper on old decorated surface of wall including preparation of surface by washing, rubbing down and stopping of distempered and painted surface complete all as specified and as directed.

M&L for two coat of oil emulsion distemper or tinted over chalk whiting on old decorated surface of wall including preparation of surface by washing, rubbing down and stopping of distempered and painted surface complete all as specified and as directed.

M&L for one coat of synthetic enamel paint on old painted wood based surface of any description otherwise described over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M&L for one coat of synthetic enamel paint on old painted steel surface of any description otherwise described over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M&L for two coat of wall care putty on wall after removing of existing treatment including preparation of surface by washing, rubbing down complete all as specified and as directed.

M&L for two coat of wall care putty on ceiling after removing of existing treatment including preparation of surface by washing, rubbing down complete all as specified and as directed.

M&L for two coat of oil bound distemper on wall complete all as specified and as directed.

M&L for two coat of oil bound distemper on ceiling complete all as specified and as directed.

M&L for one coat of weather proof acrylic emulsion exterior paint over existing surface of wall including preparation of surface by washing, rubbing down complete all as specified and as directed.

M&L for two coat of weather proof acrylic emulsion exterior paint over a coat of acrylic emulsion exterior primer on old surface of wall complete all as specified and as directed.

G S Enterprises & Co

M/S CHANDAN ENTERPRISE

Vicky Construction

RAJIB GOSWAMI ENTERPRISE