GE/863/EWS-T-59/2019-20

Amount

Excavation in trenches in hard/dense soil not exceeding 1.50m wide and not exceeding 1.50m deep for foundation pipe line etc. for shafts, wells, cesspits, manholes, pier holes etc. and not exc. 10 sqm on plain and not exceeding 1.50m in depth and getting out, complete all as specified and directed by Engineer-in-charge.

Returning, filling in, including spreading, leveling, watering and well ramming excavated soil in layers not exceeding 25cm thick each in trenches, after the pipes have been laid and tested, complete all as specified and directed by Engineer-in-charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engineer-in-charge.

M&L for Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete, complete all as specified and directed by Engineer-in-charge.

M&L precast cement concrete solid blocks using PCC (1:3:6) type C-1 as in wall exceeding 10 cm in width and setting in Cm 1:4, complete all as specified and directed by Engineer-in-charge.

M&L for rendering 15mm thick in cement mortar 1:4, mixed with water proofing compound on concrete surfaces/PCC solid blocks masonry, trowelled to even and smooth finish without using extra cement, , complete all as specified and directed by Engineer-in-charge. (Supply only water proofing compound shall be paid and measured separately under this schedule)

Supply only integral water proofing compound, complete all as specified and directed by Engineer-in-charge.

M&L for Precast reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in cover slab etc. set laid, including provision of necessary formwork, complete all as specified and directed by Engineer-in-charge. Note : (i) Reinforcement shall be measured and paid separately.

Mild steel of Gde Fe-290 (Gde E-165) as in bend, straps, rungs, handle, holdfast, manhole cover frame and similar small articles, complete all as specified and directed by Engineer-in-charge.

Mild steel TMT bars, 6 to 8mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and directed by Engineer-in-charge.

M&L for Plain cement concrete (1:4:8) , type D-2, using 40mm grade stone aggregate as in concrete bed to drain pipes laid to falls in trenches in any depth including packing under and haunching against the sides of pipes for 150mm bore pipes with concrete after the pipes are laid and tested, complete all as specified and directed by Engineer-in-charge.

M & L for 150mm bore, reinforced cement concrete pipe class NP-3 laid and jointed with collars including fittings of same grade in trenches at any depth including jointing and testing, complete all as specified and directed by Engineer-in-charge. Note : (i) Excavation and earth work and concrete for bed and haunching of pipe shall be measured and paid separately.

M&L for Plain cement concrete(1:2:4) type B-1 using 20mm graded stone aggregate as surface channel/drains inside the manholes and like including weathering, slightly rounded or chamfered angles and throating as directed and provision of necessary formwork to any extent and finished exposed surface even and smooth without using extra cement, complete all as specified and directed by Engineer-in-charge.

Extra over surface channel inside of manholes for forming fair finished drains of channels 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends, complete all as specified and directed by Engineer-in-charge. (Inner girth only be measured and paid)

Add or deduct from the rate of Item no 14 here-in-before for each 25mm girth or part thereof over and under 30 cm, complete all as specified and directed by Engineer-in-charge.

Construction of 100 users Septic tank to carry sewage and sludge water, complete all as specified and shown in Drg No. STD 1320 (C) Sheet 1/3 to 3/3 of Chief Engineer Chandigarh Zone and directed. Note:- (a) Excavation and earth work shall be in any type of soil. (b) Precast cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) block masonry with solid blocks, set in CM 1:4 shall be used in walls in lieu of Brick masonary as shown in drawings. (c ) The width of Precast cement concrete (20mm graded stone aggregate ) type C-1 block masonry in walls shall be as 700 / 600 / 500 / 400 mm in lieu of width of Brick masonary 690 / 575 / 460 / 345 mm respectively as shown in drawings. (d) RCC work where ever shown in drawings as in base slab, baffle walls , Vent shaft, manhole openings with cover connection, roof slab etc . shall be M-25 Design mix, type B1 using 20 mm graded stone aggregate. (e) The cost of all above provisions and other provisions as shown in drawings shall be deemed to be included in quoted rates of this item and nothing extra shall be entertained on this account.

Construction of Soakage well 2.40 m dia and 3.0 m effective depth complete all as specified and shown in Drg No. STD 1173 (C) Sheet 1R/2 of Chief Engineer Chandigarh Zone and as directed. NOTE:- (a) Excavation and earth work shall be in any type of soil. (b) foundation in PCC 1:3:6 type C2 using 40 mm graded stone aggregate. (c) Honey combing brick walls masonry as shown in drawing. (d) RCC work where ever shown in drawings shall be M-25 Design Mix, type B1 using 20 mm graded stone aggregate (e) The cost of all above provisions and other provisions as shown in drawings shall be deemed to be included in quoted rates of this item and nothing extra shall be entertained on this account.

Demolition of cement concrete (unreinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Dismantling of wall and ceiling boards( fibre, pulp, insulation etc.) or insulation boards/ slabs/ blankets, any thickness including cover fillets complete all as specified and directed.

S&F anodised aluminium snap grid frame work for false ceiling of size of grid 605 x 605 mm including hangers, cleats, fasteners and hangers 2 mm dia GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of GI flat 40 X 3 mm size 60 mm long complete all as specified and directed.

Exposed metal frame ceiling with 8mm thick calcium silicate board of silicious and calcareous material reinforced with cellulose fibre for fixing in 600mmX600mm grid complete all as specified and directed. NOTE (frame work for ceiling shall be measured and paid seprately)

M&L for 75 mm thick Cement concrete type D-2, 1:4:8 (40 mm graded aggregate) as in sub base complete all as specified and directed.

M&L for 25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in levelling course complete all as specified and directed.

M&L for Non-skid ceramic tiles, coloured, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sq m but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer of cement mortar 1:4 complete all as specified and directed.

M&L for coloured reflective chequered cement concrete tiles 30cm x 30cm x 25mm thick, With grey cement and pigments, set, jointed and pointed in neat cement slurry ,over and including 20 mm thick screed bed or bedding layer of cement mortar 1:6, over new or existing sub-base in floors complete all as specified and directed.

M&L for 50 mm thick Cement concrete 1:3:6 type C1, (20 mm graded aggregate), as in plinth protection, finishing cement concrete surface fair and even without using extra cement laid in alternate panels complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any guage, thickness from roof covering complete all as specified and directed.

S&F for Galvanised, corrugated mild steel sheeting, 0.63 mm thick, with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in roofs etc. complete all as specified and directed.

S&F for 0.80 mm thick Plain,Galvanised sheet , in ridges, hips, valley gutters, drip and straight flashings(length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

Taking down and romoving Chowkats or frames not exc. 1.5 sq.m with shutter (without taking off shutters from the frames) complete all as specified and directed.

Taking down and romoving Chowkats or frames exc 1.5 sq. m but not exc 4 sq. m with shutter (without taking off shutters from the frames) complete all as specified and directed.

Taking down Shutters of any description area exc 1 Sqm but n.exc. 2 Sqm Each complete all as specified and directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening as per specification and drawing complete all as specified and directed.

S&F factory made soilid panel PVC Door shutter 30mm thick (Style) consisting of frame made out MS frame shall be covered with heat moulded plain coloured PVC 'C' channel having PVC sheet stripof 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail, & bottom rail; Panneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing complete all as specified and directed.

S & F 30 mm thick flush shutter solid core construction, with block board core and plywood face panels , commercial type on both sides complete all as specified and directed.

S&F 35mm thick second class hard wood Glazed and skelton door shutters , open rebated and prepare to receive glass, gauge etc, size of members of shutters as specifed in SSR part I clause 8.24 (b) supplied and fitted to chowkat complete all as specified and directed.

S&F 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 100 mm Butt hinges, Medium weight, cold rolled mild steel, complete all as specified and directed.

S&F 150 mm Aluminium handles, cast type, anodised complete all as specified and directed.

S&F 150mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F MS framed work such as grills, gratings, etc with ends of bars shouldered or riveted framed guard bars and similar work confirming to Fe-290 Gde E- 165 complete all as specified and directed.

S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm & fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F in repair 1000 Ltrs capacity, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part – I, including 20 mm bore ball brass valves, high pressure with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed to 20 mm bore steel tube complete all as specified and directed.

Taking up or down steel tubing 15 mm bore, and connections, including cleaning for re-fixing or removal complete all as specified and directed.

S & F 15 mm bore, steel water tubing, medium grade, galvanized, with all fitting and fixed complete to walls and ceiling or laid into floor complete all as specified and directed.

Fixing only 15 mm water tubes, any grade, to walls and ceilings or laying in floors complete all as specified and directed.

Taking up or down steel tubing 20 mm bore, and connections, including cleaning for re-fixing or removal complete all as specified and directed.

S & F 20 mm bore, steel water tubing, medium grade, galvanized, with all fitting and fixed complete to walls and ceiling or laid into floor complete all as specified and directed.

Fixing only 20 mm water tubes, any grade, to walls and ceilings or laying in floors complete all as specified and directed.

S&F in repair Bib taps, cast copper alloy, fancy type, chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15 mm bore steel tube complete all as specified and directed.

S&F in repairs 15mm bore stop valve/angle valve cast copper alloy chromium plated, fancy type, screwed down, high pressure, with crutch or butter fly handlescomplete all as specified and directed.

S&F in repair PVC valve less syphonic action type low level flushing cistern white of capacity 10 Ltrs with inlet valve float and fixed to water closet with PVC flushing pipe 32mm dia and PVC connection of size 15x300mm complete all as specified and directed.

S&F in repairs Vitreous china squatting pan 'Orissa pattern' size 580X 440 mm white with integral foot rest (exluding flushing cistern and flush pipe) including connection to trap,concrete and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and directed.

S&F in repair Vitreous china wash down water closet pan (pedestal pattern), white, including flush pipe of polyethylene of low or high density or PVC 32 mm dia., including plastic water closet seat ,closed pattern with cover and hinging device and trap with connection complete all as specified and directed.

S&F Chromium plated jet for EWCcomplete all as specified and directed.

S&F in repairs Vitreous china wash hand basin, white, flat back, size 550 X 400 mm including fixing with brackets including waste pipe and 32 mm chromium plate waste fitting with long screwed shanks and fly-nuts complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts of length 600 mm in complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 125mm size for iron pipe or for unions and fixed to 15 mm bore steel tube complete all as specified and directed.

S&F in repair CP tubular towel rail, 20 mm dia, 60 cm long between flanges complete all as specified and directed.

S&F in repairs Soap dish, cast copper alloy, chromium plated with screws in complete all as specified and directed.

S&F in repairs 110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F in repairs 75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

Taking down cement plaster of any description on brick or concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water etc. Complete all as specified and directed.

M&L two coats of cement base paint including preparation of newly plastered surfaces of wall Complete all as specified and directed.

S&F butt hinges, 50 mm medium weight, cold rolled mild steel complete all as specified and directed.

S&F second class hardwood small fittings as in shaped door/ window stops incl all necessary labours, articles exc 200 cucm but n. exc. 500Cucm each complete all as specified and directed.

M&L two coats of synthetic enamal paint to steel surfaces of any discription over 10 cm width or girth not otherwise described over and including a coat of red oxide primer after preparation of surfaces complete all as specified and directed.

M&L for washing rubbing down and applying two coat of white wash to old surfaces of walls complete all as specified and directed.

M&L for washing rubbing down and applying of two coat of cement base paint to old surfaces of walls complete all as specified and directed.

Removing of old paint by paint removers or burning off by blow lamps and cleaning with scrapers, any number of coats, any width or girth and applying two coats of synthetic enamal paint over priming surface of red oxide to surfaces of any discription over 10 cm width or girth not otherwise described incl preparation of surfaces to old surfaces of walls complete all as specified and directed.

M&L PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate as in benching in cover slab over manholes, bend, coping, bed plate etc. includind form work if any and making surface smooth and even without using extra cement complete all as specified and directed.

Net Contract Sum will be after deducting Sch Of Creditof Rs. 25,014.00

M/S Shamsher Negi Dewa

A P ENTERPRISES

GULATI BUILDERS

Pankaj Builders

M/S Dahiya Builders

M/S Gulab Singh

M/S J.S.ENTERPRISES