Furniture and Internal Fitouts works at JNV East Jaintia Hills Meghalaya

(A) CLASSROOM

(i) CLASSROOM DESK LARGE SIZE Supply & installation Big Desk (for two persons)-The overall dimensions of desk will be 1066mm x 930mm x Height 760mm, complete as per Specifications enclosed and direction of Engineer-in- charge having the Table top shall be made up of 18.0 mm thick plywood IS 303 of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish). Table top dimensions shall be W 930 mm x D 380 mm. Edge towards bench shall be post formed with round edge. The remaining three edges must be sealed with 2mmthick PVC edge banding tape. Edge band must be trimmed on edges and corners. The desk shall be have low chemical emission of VOCs (Voltage Organic Compounds) and carcinogens, contributing to a healthier room environment. Seat and back rest shall be made of 18mm thick plywood of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish) except back rest. Back rest shall be have both sides colour lamination. Technical details of seat and back rest are mentioned below:Seating bench dimensions shall L 930 mm x W 300 mm x H 450 mm. Front side shall be rounded with post forming. Remaining three edges shall sealed with 2mm thick PVC edge banding tape. Back rest dimensions shall L 930 x H 200 mm Upper side shall be rounded with post forming Remaining three edges shall be sealed with 2mm thick PVC edge banding tape. Desk Shelve shall be made of prime quality 0.8mm thick CRCA sheet of H150mmxD300mm and side stiffeners of CRCA tube size 19mmx19mmx1mmthick. One vertical support (partition) of square tube size 25mm square x1.2mm thick must be provided at centre of tray . Upper modesty made of prime quality 0.8mm thick CRCA Sheet Powder Coated should be embossed with dimples in round shape, height will be 150mm, there should be Perforated lower modesty Made of prime quality 0.8 mm thick CRCA sheet of size H150mmXD21mm with square perforation, CRCA Tube of size 19x19x1mm thick to be inserted for full length at bottom of Jali . Bag hook should be provide on both side of piller made of minimum 4mm dia rod Side frame structure:- Made of prime quality CRCA pressed form section 165mmx25mmx1mm thick welded to 25mmx50mmx1.2mm thick CRCA tube , Seat and back side frame structure made of prime quality CRCA pressed form section 165mmx25mmx1mm thick welded to 25.4mm diameter x 1.6mm thick ERW- 1pipe , there will be 8no. horizontal supports are 25mmx25mmx1.2mm thick CRCA pipes. . Bottom Rectangular tube 50x25x 1.2mm thick should be closed with PPCP cap bothside sand pipe dia. 25.4x1.6mm thick should be closed with metal (Backside) and other side (Undertheseat) PPCP cap, complete as per engineer incharge Desk should be in semi knock down form with the help 16 connecting pipes ; 8 pipes on each side : connecting pipe size will be 20x20x1.2mm .All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations with CO2 Welding Shall Be Used , CRCA Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil , Grease , Dust And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² , Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process , Metal Pipe & 7 tank treatment with minimum 45-50 micron powder coating.

(ii) CLASSROOM DESK MEDIUM SIZE Supply & installation Medium Desk (for two persons)-The overall dimensions of desk will be 900mm x 890mm x Height 690mm, complete as per Specifications enclosed and direction of Engineer-in- charge having the Table top shall be made up of 18.0 mm thick plywood IS 303 of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish). Table top dimensions shall be W 890 mm x D 380 mm. Edge towards bench shall be post formed with round edge. The remaining three edges must be sealed with 2mmthick PVC edge banding tape. Edge band must be trimmed on edges and corners.The desk shall be have low chemical emission of VOCs (Voltage Organic Compounds) and carcinogens, contributing to a healthier room environment. Seat and back rest shall be made of 18mm thick plywood of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish) except back rest. Back rest shall be have both sides colour lamination. Technical details of seat and back rest are mentioned below:Seating bench dimensions shall L 890 mm x W 300 mm x H 400 mm. Front side shall be rounded with post forming. Remaining three edges shall sealed with 2mm thick PVC edge banding tape. Back rest dimensions shall L 890 x H 200 mm Upper side shall be rounded with post forming Remaining three edges shall be sealed with 2mm thick PVC edge banding tape. Desk Shelve shall be made of prime quality 0.8mm thick CRCA sheet of H150mmxD300mm and side stiffeners of ss CRCA tube size 19mmx19mmx1mmthick. One vertical support (partition) of square tube size 25mm square x1.2mm thick must be provided at centre of tray . Upper moedsty made of prime quality 0.8mm thick CRCA Sheet Powder Coated should be embossed with dimples in round shape, height will be 150mm, there should be Perforated lower modesty Made of prime quality 0.8 mm thick CRCA sheet of size H150mmXD21mm with square perforation, CRCAT ube of size 19x19x1mm thick to be inserted for full length at bottom of Jali . Bag hook should be provide on both side of piller made of minimum 4mm dia rod Side frame structure:- Made of prime quality CRCA pressed form section 165mmx25mmx1mm thick welded to 25mmx50mmx1.2mm thick CRCA tube , Seat and back side frame structure made of prime quality CRCA pressed form section 165mmx25mmx1mm thick welded to 25.4mm diameter x 1.6mm thick ERW- 1pipe , there will be 8no. horizontal supports are 25mmx25mmx1.2mm thick CRCA pipes. . Bottom Rectangular tube 50x25x 1.2mm thick should be closed with PPCP cap bothside sand pipe dia. 25.4x1.6mm thick should be closed with metal (Backside) and other side (Undertheseat) PPCP cap, complete as per engineer incharge Desk should be in semi knock down form with the help 16 connecting pipes ; 8 pipes on each side : connecting pipe size will be 20x20x1.2mm .All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations with CO2 Welding Shall Be Used , CRCA Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil , Grease , Dust And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² , Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature

(v) TEACHER BOARD [Excluding cost of Interactive Flat-Panel Display (IFPD)] Technical Specification for Smart Board with Double-Track Sliding System for Green and White Boards fitted in an Anodised Aluminium Frame with concealed cable management and provision for mounting of Digital Screen: Supply, installation, testing, commissioning (SITC) of an integrated digital teaching–learning solution comprising: (a) Anodised Aluminium Frame, double track sliding system for white & green board and provision for mounting of digital screen with concealed cable management, (b) Vitrified magnetic ceramic-steel Green Board and White Board panels. •Dimensions and Configuration: Total Width of the Setup is ~12 feet and height ~4.0 feet from the board surface (excluding the width of aluminium frame). • Material: Providing and fixing anodised aluminium (alloy 6063-T6) framed sliding system for smart board with minimum 2.0 mm thick extruded sections, anodised to AA1 grade as per IS 1868, mounted on a heavy-duty top-hung aluminium track (min. 2.5 mm thick) with sealed ball-bearing nylon/PU rollers (load capacity not less than 120 kg per panel), concealed bottom guide, EPDM gaskets, SS-304 fasteners, pelmet/valance cover, and soft end-stops/soft-close mechanism, including all brackets, fixings, alignment, cable provisions, commissioning, and making good complete as per drawings and Engineer-in-Charge. •Design: One slot to fix IFPD, other slot for Green & White boards sliding on double track system with Locking facility on sliding frame to keep the IFPD display safe. •Top & Bottom Rails: Tracks shall be aligned and reinforced to ensure boards move easily and without wobble. • Back Side: The backside of the smart board, to concealed the wall surface, provided & fixed with 18 mm thick HDHMR board laminated (white coloured matte finish) with 0. mm, edges sealed with 1 mm PVC edge banding, fixed to the anodised aluminium frame with concealed screws/rivets, with ventilation slots as required, and shall be moisture, termite and borer resistant. •Load Capacity: Safe to hold IFPD + white & Green boards with ≥1.5× safety factor. •Cable Management: Built-in channels for power, LAN, HDMI, USB. •Safety: Rounded edges, tamper-resistant covers, concealed fixing. •Finish: Durable, corrosion-resistant coating suitable for indoor use. •Additional Requirements: (a) All boards and the structure must be securely fixed to the wall with appropriate fasteners. (b) Provision for cable management must be included for the IFPD (i.e., concealed conduit/path for power and data cables). (c) The unit must be free from sharp edges, splinters, or any protruding parts that could cause injury. (d) Installation height should ensure comfortable writing access for average adult and student height (typically bottom edge ~2.5 to 3 feet from the floor). (b) Vitrified magnetic ceramic-steel Green Board and White Board panels: •Function: Boards shall slide horizontally on a top and bottom aluminium/steel channel track to fully cover or reveal the IFP as needed. •Material: Vitrified ceramic-steel, magnetic, double-coated. •Sliding Boards: Quantity: 1 no. Green board & 1 no. White board. •Green Board Surface: Matte, chalk-friendly, stain/scratch resistant. •White Board Surface: Glossy surface, Dry-erase marker friendly, ghost-free, easy clean. •Size: ~6 feet (W) × 4 feet (H) (Each Board) with

(v) VICE-PRINCIPAL ROOM CHAIR High Back Revolving Chair, Overall Dimension:- 700W ±10 x 700D ±10 x 1210H ±10 mm,Seat of Medium back chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat,Used PU Moulded foam on Seat of D-45 kg/m3 , Back of chair is made of Injection moulded PP material structure upholstered with Mesh fabric , Adjustable Lumber support upholstered with fabric , Adjustable Headrest on back Upholstered with Mesh Fabric ,Seat Size:- 470W ±10 x 460D ±10 x 70Thick. ±5 mm , Back Size: 500W ±10 x 780H ±10,Mechanism:- The Synchro tilt Mechanism ,Used gaslift of 90 mm size of Class-IV grade, Armrest:- PU padded adjustable armrest fixed with Seat ,Chair Base & Wheels: SS 202 Polished Finish base consists of 5 prongs with 640±5 mm pitch circle diameter, 50mm Dia. Black Nylon - Twin Wheel Pin castor .

(iii)SOFA FOYER THREE SEATER Size in mm - 1930(L) X 755(D) X 750(H) Seat Wooden Structure Uphostered With Leatherite & HD Foam 32 Softy. SS Chrome . Sofa S57 Max. Height 750mm . The rounded Armrests Provided Sleek And Stylish Look With The Pillowed Back . Arm Rest Leatherite Covered With Solid Wood Structure . Understructure Made By Solid Wood Structures With Heavy Quality Spring For Maximum Comfort , Taper Type 25mm Round Spiral Spring . Legs Round Pipe Chrome Plated Legs . Understructure Made of Base Frame Strongly Jointed Wooden Plywood Parts . 3 Seater Sofa Seat Height From Ground 460mm .3 Seater Sofa 2020W x 760D x 750H , 2 Seater Sofa 1450W x 760D x 750H . Seat Height From Ground 460mm & 1 Seater Sofa 880W x 760D x 750H . 100mm High Legs.

(ii) WORK SPACE WITH IN-BUILT LOCKABLE OVERHEAD STORAGE SPACE FOR STAFFROOM (AS PER ACTUAL REQUIREMENT) Supplying and installation of site knock-down type modular wall-mounted workspace unit of approximate size 900W x 600D x 750H mm (for one staff), including working counter and lockable overhead storage cabinet of 900W x 450D x 650H mm. The structure shall be made of 18 mm thick BWP grade plywood with decorative laminate on external surfaces and balancing laminate on inner faces conforming to IS:303/IS:12406. All exposed edges shall be sealed with 2 mm PVC edge banding. The worktop shall be 25 mm thick Laminated Plywood board with post-formed front edge and machine-pressed PVC edge banding, securely fixed to the wall using concealed MS cleats and brackets. The overhead cabinet shall be fitted with soft-close concealed hinges, SS handles, and magnetic catchers of approved make, with one adjustable shelf and modular connectors for alignment and expansion to adjoining units. Each workspace shall include provision for electrical connectivity with 6A/16A modular sockets (as per requirement) positioned at approximately 450 mm above finished floor level for easy access. The worktop shall have a circular cable hole (50–60 mm diameter) with grommet for laptop and equipment wiring. All wiring, sockets, and conduits shall be concealed neatly within the table body, routed through internal PVC raceways to maintain a clean, clutter-free appearance. Junction boxes and ducts shall be integrated to provide safe, organized cable management without visible wiring. The entire unit shall be wall-mounted using heavy-duty MS brackets or suitable fasteners based on wall type, finished neatly with matching silicone sealant at all joints. All fittings and hardware, including soft-close hinges and handles, shall be of reputed make. The unit shall be termite-resistant, moisture-resistant, easy to maintain, and made from ISI-marked prime quality boards. The overall layout and detailing shall match the approved reference image, with actual dimensions finalized as per site requirements and direction of the Engineer-in-Charge.

(i) Supply and installation of Glass-door Storage of Size 915 mm (W) x 482mm (D) x 1980mm (H). It should have shelf thickness of 0.8mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) with clear glass of > 4.0 mm thick and all other components shall have a thickness of 0.8mm. These components shall be made of CRCA steel sheet ‘D’ grade high yield strength as per IS 513:2008 The glass door storwel shall have a SS handle and a Two-way locking mechanism with shooting bolt. It should have a height-wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base.All metal components would be epoxy polyster powder coated DFT 50-60 Micron confirimg to IS 13871:1993.

(iv) Chair, Overall Dimension:- W600±10 x 600D ±10 x 890H ±10 mm,Seat of Medium back Visitor chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat , Used PU Moulded foam on Seat of D-45 kg/m3, Back of Medium back chair is made of Injection moulded PP material structure with Mesh fabric, Seat Size:- 460W ±10 x 470D ±10 x 60Thick. ±5 mm , Back Size:- 440W ±10 x 470H ±10,Armrest:- Fixed PP armrest ,Understructure:- Cantilever frame made SS Polished Finish round pipe with Plastic bushes . Frame Material -SS 202 Polished Finish

(i) PHYSICS LAB

(ii) CHEMISTY LAB

(iii) BIOLOGY LAB TABLE

ALONG THE WALL TABLE:: Supply and installation of Along-the-wall knock down type modular laboratory tables of size 1400 MM(L) (Length may vary as per actual requirement) × 750 MM (W) × 900MM H . Above the counter, with an internal conduit for all wiring. Modular switch plates and 02 nos of 220V/16A Switch socket (with individual circuit protection) will be CNC-mounted every 1 m (or per site layout). All conduits and components shall comply with applicable laboratory safety and performance standards. Dust-proof, removable access covers to permit maintenance and future upgrades, and outlets to be ergonomically positioned for seated and standing use. A

KITCHEN & DINING

ISLAND TABLE:The laboratory table shall be provided as knock down type modular ISLAND laboratory tables units of overall size 8000(L) (Length may vary as per actual requirement) × 1500(W) × 900H . It shall be constructed in modular segments of 1400(L) × 1500(W) × 860(H) mm each for ease of manufacture, handling, and installation. The worktops will include a powder-coated bus running their full length, above the counter, with an internal conduit for all wiring. Modular switch plates and 04 nos (02 Facing each side) of 220V/16A Switch socket (with individual circuit protection) will be CNC-mounted every 1 m (or per site layout). All conduits and components shall comply with applicable laboratory safety and performance standards. Dust-proof, removable access covers to permit maintenance and future upgrades, and outlets to be ergonomically positioned for seated and standing use. Additional switches and sockets shall be provided as required. All base storage cabinets shall be of the design “1 Drawer + 2 Shutters” made of 0.8 mm thick Powder Coated CRCA. Each storage box without granite shall be 600W × 570D × 713H, supported on 100 mm legs and shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The upper top shall be of 18-19 mm thick black granite, with all joints sealed using silicon sealant. The cabinet bodies shall be of over-closing design, fabricated entirely on CNC machines to ensure precision. The storage bodies shall be neatly jointed with accurately matched sides to avoid gaps. Shutters shall be made of 0.8 mm thick Powder Coated CRCA with handles, and drawers shall run on Soft close sliding channels (35-50kg). The worktops shall be of 18-19 mm thick black granite, flushed with sink units and taps. Installation shall include all utility service outlets, accessory fittings, plumbing, electrical switches, and fittings shall be as per requirement. All metallic parts shall be with corrosion resistant coating and shall be welded strongly using CO₂ welding, conforming to safety regulations. Panels shall be secured with nuts, bolts, and riveting.

BOYS AND GIRLS DORMITORIES

ISLAND TABLE: The laboratory table shall be provided as knock down type modular ISLAND laboratory tables units of overall size 8000(L) (Length may vary as per actual requirement) × 1500(W) ×900(H) mm × 1550H (two-tier). It shall be constructed in modular segments of 1600(L) × 1500(W) × 860(H) mm each for ease of manufacture, handling, and installation. Four standard SS304 sinks shall be installed, each fitted with a 3-way SS 304 faucet of Premier make. Stainless steel 304 reagent racks shall be provided across the entire table length in centre except the sink areas, with dimensions 300D × 700H. These racks shall also b

STAFF QUARTERS

(A) ROOMS WARDROBE

(B) MODULAR KITCHEN

e of modular design with two horizontal stainless steel shelves, cutouts for switches and sockets, provision for electrical outlets, and accommodation for granite pieces. All base storage cabinets shall be of the design “1 Drawer + 2 Shutters” made of 0.8 mm thick Powder Coated CRCA. Each storage box without granite shall be 600W × 570D × 713H, supported on 100 mm SS legs and shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The upper top shall be of 19 mm thick black granite, with all joints sealed using silicon sealant. The cabinet bodies shall be of over-closing design, fabricated entirely on CNC machines to ensure precision. The storage bodies shall be neatly jointed with accurately matched sides to avoid gaps. Shutters shall be made of 0.8 mm thick powder coated Powder Coated CRCA with handles, and drawers shall run on Soft close sliding channels (35-50kg). Reagent shelves shall be made of a polished finish SS, provided with electrical switches, sockets, and cutouts as required. The worktops shall be of 19 mm thick black granite, flushed with sink units and taps. Installation shall include all utility service outlets, accessory fittings, plumbing, electrical switches, and fittings shall be as per requirement. All metallic parts shall be with corrosion resistant coating and shall be welded strongly using CO₂ welding, conforming to safety regulations. Panels shall be secured with nuts, bolts, and riveting.

ISLAND TABLE: The laboratory table shall be provided as knock down type modular ISLAND laboratory tables units of overall size 8000(L) (Length may vary as per actual requirement) × 1500(W) × 900(H) mm × 1550H (two-tier). It shall be constructed in modular segments of 1400(L) × 1500(W) × 900(H) mm each for ease of manufacture, handling, and installation. Four standard SS304 sinks shall be installed, each fitted with a 3-way SS 304 faucet of Premium make. Stainless steel reagent racks shall be provided across the entire table length in centre except the sink areas, with dimensions 300D × 700H. These racks shall also be of modular design with two horizontal stainless steel shelves, cutouts for switches and sockets, provision for electrical outlets, and accommodation for granite pieces. All base storage cabinets shall be of the design “1 Drawer + 2 Shutters” made of 0.8 mm thick Powder Coated CRCA. Each storage box without granite shall be 600W × 570D × 713H, supported on 100 mm legs and shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The upper top shall be of 18-19 mm thick black granite, with all joints sealed using silicon sealant. The cabinet bodies shall be of over-closing design, fabricated entirely on CNC machines to ensure precision. The storage bodies shall be neatly jointed with accurately matched sides to avoid gaps. Shutters shall be made of 0.8 mm thick Powder Coated CRCA with handles, and drawers shall run on Soft close sliding channels (35-50kg).. Reagent shelves shall be made of polished finish SS, provided with electrical switches, sockets, and cutouts as required. The worktops shall be of 18-19 mm thick black granite, flushed with sink units and taps. Installation shall include all utility service outlets, accessory fittings, plumbing, electrical switches, and fittings shall be as per requirement. All metallic parts shall be with corrosion resistant coating and shall be welded strongly using CO₂ welding, conforming to safety regulations. Panels shall be secured with nuts, bolts, and riveting.

(B) DINING BENCH Dining Bench: The Bench shall be of size 1800 mm in length, 300 mm in depth, and 450 mm in height, suitable for use in residential schools. The bench top shall be made of 18 mm thick HDHMR + Laminated , finished with a 1 mm thick decorative laminate on the top surface, and a balancing laminate backing on the underside to ensure dimensional stability. All exposed edges shall be sealed with PVC edge banding or machine-finished to prevent splinters and enhance durability. The plywood shall be scratch-resistant, water- resistant, and easy to clean, with a light woodgrain or equivalent finish as approved. The supporting frame shall be fabricated frame of square hollow section 40mmx40mmx1.6mm SS 304 grade stainless steel in polished finish. These legs shall be securely welded to the underside of the benchtop frame. The bench shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The design shall prioritize user safety with no sharp corners or edges. The bench must be structurally sound and capable of supporting a uniformly distributed load of at least 250 kg. All materials used must conform to relevant IS standards, and the finished product should be free from burrs, dents, or deformities.