PROVN OF 01 X TOILET BLOCK NEAR PUF SHELTER NO 174/1 AT EPU, RAISED PATHWAY FOR OTM WITH INTERLOCKING TILES AT ENGR REGT AND OTHER SANCTIONED WORKS IN THE AREA OF AGE B/R-I UNDER GE PANAGARH

Amount

Excavating in trenches, n.exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Removing excavated spoil to a distance n.exc 50m and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm complete all as specified and directed.

M&L for PCC type D2 1:4:8 (using 40 mm graded stone aggregates) as in foundations, fillings and mass concrete complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for flat rough finished surfaces of concrete complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe 410 -W (Gde E- 250) quality A complete all as specified and directed.

M&L for preparation of painting of new steel surfaces over 10 cm in width or girth over a coat of primer using red oxide and applying two coats of synthetic enamel paint complete all as specified and directed

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel as in ridges sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Excavating over areas, n.exc 1.5 m deep and getting out soft/loose soil complete all as specified and directed.

M&L for brickwork with fly ash old sized bricks, straight or curved on plan exc 6 m mean radius, built in CM (1:6) complete all as specified and directed.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM (1:6) and finishing fair even and smooth without using extra cement.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n.exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for hardcore using broken stone or boulders of gauge n.exc. 63 mm, deposited, spread and levelled in layers n.exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100 mm thick cement concrete 1:4:8 type C2 (using 40 mm graded aggregates) as in sub base of floor complete all as specified and directed.

M&L for 100 mm thick Cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) fair finished even and smooth with using extra cement complete all as specified and directed.

M&L for 75 mm thick cement concrete type B-1, 1:3:6 (using 20mm graded stone aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound grade A complete all as specified and directed.

M&L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M&L for brickwork with fly ash modular bricks straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and directed.

M&L for formwork for rough finished surface of concrete (flat surface) to sides of pillars, posts, struts, piers, columns, and stanchions complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for fair finished surfaces of concrete complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for rough finished surface, n.exc 200m thick (Horizontal or sloping) complete all as specified and directed.

M&L for reinforced cement concrete (Design Mix) M-25 (using 20mm graded stone aggregate) foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc. and mass concrete etc complete all as specified and directed

M&L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) in columns, pillars, piers, etc complete all as specified and directed.

M&L for reinforced cement concrete (Design Mix) M-25 (using 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for reinforced cement concrete (Design Mix) M-25 (using 20mm graded stone aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for mild steel TMT bars 5mm dia and over upto including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete wall surface finish the surfaces fair and even complete all as specified and directed.

Supply only Integral Water proofing compound complete all as specified and directed. (Make : Pidilite Industries/ Impermo/Snowcem India Ltd/Sika)

M&L for rendering 15 mm thick cement plaster in CM (1:6) on external fair faces of brick/concrete work surfaces finished even and smooth (without using extra cement) incl WPC complete all as specified and directed. (Note: WPC will be measured and paid separately).

M&L for rendering 10mm thick on fair faces on roof surfaces of concrete surfaces in cement mortar (1:4) mixed with water proofing compound complete all as specified and directed. (Note: WPC measured and paid separately complete all as specified and directed).

M&L for preparation of new surfaces of roof and applying two coats of Polyurethane (PU) acrylic based water proofing liquid compound over and including one coat of self priming primer @ one litre per 10 Sqm with reinforcing fabric sheet as per manufacturer's instructions to stop leakage/seepage from roof/wall complete all as specified and directed by the Engr-in-Charge (Notes :- (i). As per description of this item, minimum two coats of Polyurethane (PU) acrylic based water proofing liquid compound over one coat of primer shall be carried out as per manufacturer's instruction. Please note no price adjustment shall be made, if as per manufacturer's instructions more coats of Polyurethane (PU) acrylic based water proofing liquid compound and primer are required for roof treatment. (ii). Quoted Rate shall be deemed to be included for work in building/structure of any height).

M&L for rendering 5 mm thick in CM (1:3) on fair faces of brick work or concrete wall surfaces & finishing the surfaces fair and even on ceiling complete all as specified and directed.

M&L for preparation of new plastered or un-plastered surfaces of walls applying two or more coats of 100% premium acrylic emulsion (Exterior weather coat) paint having VOC less than 50 gm/litre and UV resistance exterior paint of required shade (Company depot tinted) with silicon additives@ 1.43 litre/10sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surfaces complete all as specified and directed. (Make: M/s Apex Ultima of Asian/ Weather Coat all guard of Berger/Xtra Tough of Shalimar).

M&L for preparation new plastered surfaces and applying three coat of white washing on ceiling complete all as specified and directed

M&L for cement concrete type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) 25 mm thick as in floor for receiving screed bed for floor finishes complete all as specified and directed.

M&L for coloured non skid ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.06sqm but n.exc 0.11 sqm, in floors etc set and jointed in neat cement slurry over and including 15 mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed.

S&F bib tap long body with CP nipple cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed for iron pipe, suitable for 15 mm bore complete all as specified and directed.

S&F pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long with aluminium alloy brackets and guard rail complete all as specified and directed

S&F tubular towel rail 20mm dia D type and 60cm long between flanges of brass chromium plated complete all as specified and directed.

S&F stop valve cast copper chromium plated concealed with long shank type screwed down, high pressure with capstan head suitable for 15 mm bore complete all as specified.

S&F Grating square 150 mm size of PTMT (Minimum weight 100gms) complete all as specified and directed

S&F 15 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and directed.

M&L for glazed ceramic tiles 350 x 250 mm x 7 mm/ 350x450x7mm thick in vertical surfaces such as risers, skirting and dados, set and jointed in neat cement slurry and pointed in coloured cement to match including 10 mm thick cement plaster in CM 1:3 on brick or concrete surfaces complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be convered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvant cement for stiles and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert of top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitabale PVC sheet beading, and jointed together with solvant cement, and S&F in the frame at side as per specification and drawing complete all as specified and directed.

S&F solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F anodised powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed

S&F Anodised powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No). hinges type B-21 100mm long (2 No) suitable handle (1 No) complete all as specified.

S&F sheet glass 5.5 mm thick, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F 100 mm size butt hinges extruded aluminium alloy with galavanised mild steel hing pin anodised and fixed type C-21 complete all as specified and directed

S&F 200 mm long Aluminium, anodised, barrel tower bolt of extruded section complete all as specified and directed.

S&F aluminium handles, cast type, anodised 150mm long complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy and fixed complete all as specified and directed.

S&F vitreous china water closet (pedestal pattern) complete including provision of lime concrete bedding white, including plastic WC seat cover, closed pattern with flat bottom and mild steel CP hinging device and incl CP jet nozzle for EWC including connection to GI pipe line, complete all as specified and directed.

S&F vitreous China Squatting pan ‘Orissa’ pattern, size 580 X 440mm, white, with integral foot rests and with ‘P’ or ‘S” trap, (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc and including provision of lime concrete bedding and make good the disturbed surface, complete all as specified and directed.

Supply only 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets (Fixing rate included in Ser item No 69 above of WC item)

S&F vitreous china wash basin white, flat back, size 550X400 mm including cutting for pinning in ends of brackets, complete all as specified and directed.

Supply flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450mm complete all as specified and directed

S&F soap dish, vitreous china white, approximate size 160 x 160 x 90mm complete all as specified and directed.

S&F PVC (SWR) floor trap 75mm dia of outlet plain with grating including jointing with solvent cement complete all as specified and directed

S&F PVC (SWR) bends any radius of 75 mm bore with access door complete all as specified and directed.

S&F Vitreus China bowl urinal flat back Size of 465 x 355 x 265 mm white with grating and union for discharge pipe complete all as specified and directed.

S&F Urinal Spreader of PTMT any colour for fixing with 15 mm dia pipe complete all as specified and directed

M&L for laying Reinforced concrete pipes 150 mm in dia, class NP2, laid and jointed complete with collars complete all as specified and directed.

M&L for concrete bed to 150 mm dia drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 (using 40mm graded stone aggregate) all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed.

M&L for PCC (1:2:4) 100 mm thick type B2 (using 40 mm graded stone aggregate) used as in sub base floor/pavings and finishing cement concrete surface without using extra cement complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigments complete all as specified and directed.

M&L for brickwork with flyash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4) complete all as specified and directed

M&L for PCC (1:2:4) Type B0 (using 12.50 mm graded stone aggregate) used as in copings complete all as specified and directed.

M&L for fixing PVC (SWR) pipes of 110 mm bore diameter single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc complete all as specified and directed.

M&L for 15 mm thick screed bed or bedding layer in cement mortar (1:4) for laying floor finishes complete all as specified and directed.

M&L for non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but n.exc 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified directed. (Note : Design, shade and pattern of fixing of tiles shall be as directed by Engr-in-charge)

S&F for 25mm bore GI tubing medium grade in trenches / Floor / pillar connetion in old or new postion including fittings complete all as specified and directed. (Make: Bansal / Jindal)

All as per item No 81.00 mentioned here-in-before but 40 mm bore complete all as specified and directed

S&F 25 mm bore gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed.

S&F rotational/moulded polyehtylene multilayer water tank (Cylindrical vertical with closed top) hoisted & fixed in position all as specified directed .capacity of 1000 Ltr complete all as specified and directed. (Make: Sintex / Vectus / Prayag)

S&F ball brass valves, high pressure, with polyethylene float and flynut complete, screwed for iron pipe or brass ferrule for 25mm bore complete all as specified and directed.

S&F capacity of 500 ltr Rotational / moulded Polyehtylene multilayer water tank (Cylindrical vertical with closed top) hoisted & fixed in position complete all as specified directed. (Make: Sintex / Vectus / Prayag)

EM PORTION M&L for point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLSH PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. (Note: Quoted rate deemed to be included for necessary chasing/cutting and making good the surface)

M&L for wiring for 5 Amps socket out let on independent Boards controlled by one, one way switch using 2.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 2.5 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLSH cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. (Note: Quoted rate deemed to be included for necessary chasing/cutting and making good the surface)

M&L for wiring for 15 Amps socket out let on independent Boards controlled by one, one way switch using 4 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 4.0 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLSH cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed.

S&F switch piano flush type, single pole , 5/6 Amps, one way complete all as specified.

S&F switch socket combination 2 in 1 multipurpose 5 pin , (5/6 Amps ) complete all as specified.

S&F switch socket combination 5/16 Amps 5 in 1 flush type controlled by one switch complete all as specified and directed.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified and directed.

S&F 01x 18 W LED batten light fittings, with T-8 tube, lighting fixture with extruded polycarbonate complete with all accessories and connection from ceiling rose with twin core twisted flexible copper conductor cable with suitable size and earthing complete all as specified and directed.

S&F security light fittings 25 watts, minimumm lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete suitable for pole dia 25mm complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as directed. (Make - Bajaj/Crompton/Phillips)

S&F lamp holder, PVC/polycarbonate type with back plate straight or anfular suitable for batten fittings complete all as specified.

S&F LED bulb 7 watts, 240 volts, ISI marked complete all as specified.

S&F 9W LED mirror light fitting wall mounted batten 2ft, extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 9 watt, 6000K including necessary connection complete all as specified and directed.

S&F metallic Exhaust ventilation fan of sweep 300 mm sweep, 230volt AC complete with louver and all asssesories including cutting hole of suitable size, making good surface by doing plaster and applying two coat of distemper complete with fixing connected with twin core twisted flexible copper conductor (23/0.0076) of size complete all as specified and directed

S&F epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), triple pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as directed.

S&F MCB SPN 63 Amps, 'C' curve, 240 Volts,ISI marked and to be housed in DBs complete including necessry connection all as specified and directed. (Note : Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F XLPE armoured cable 10 sqmm 2 core,1100 volts grade heavy duty cable,ISI marked passing through pipe, with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed complete all as sepcified.

Supply and lay for dry river sand filling for cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and directed. (Note : Punned thickness shall be measured).

M&L for sub class B bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete all as specified and directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth wire electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth wire encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. (Note :- (i) If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department. (ii) Testing to be carried out by the contractor in presence of Engr- in- Charge , entered in the eath testing register, prepared and to be maintained by the contractor & submited to Concerned Engr-in-Charge. (iii) T&P and testing instrument (Meger) to be provided by the contractor at own cost).

S&F metallic exhaust ventilation fan of sweep 230 mm sweep, 240volt AC complete with louver and all asssesories including cutting hole of suitable size, making good surface by doing plaster and applying two coat of distemper complete with fixing connected with rwin core twisted flexible copper conductor (23/0.0076) of size complete all as directed by Engr-in-Charge.

S&F two single core, 4 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade drawing in and including suitable size PVC conduits (ISI marked) concealed including 4 sqmm nominal cross sectional area multistranded copper conductor FRLS cable, PVC insulated unsheathed 1100 Volts grade earth wire, complete all as specified and directed. (Note: (i) Quoted rate is included for chasing and cutting and making good surface. (ii) 03 runs cable and conduit pipe will be measured as single unit)

S&F MCB SPN 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete inncluding necessary connection complete all as specified and directed. (Note: proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

M/S S M ENTERPRISE

M/S SWAPAN KUMAR MONDAL

UNIVERSAL TRADING