NIT No: 11/IHM-GH/SE/CE/NRANVP/2026-27, Nava Raipur Atal Nagar, Dist.Raipur , Dated:28.04.2026

Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits. In all types of soil

Surface dressing of the ground including removing vegetation and making up undulations and in-equalities not exceeding 15 cms in depth/ height including disposal of rubbish upto 1.5 m lift and lead upto 50m (at least 5m away from the dressed area).

Providing and filling in plinth with sand/ Crusher dust under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete.

Backfilling: Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering with a lead upto 50 M. and lift upto 1.5 M.

Providing and laying nominal mix cement concrete with crushed stone aggregate using concrete mixer in foundation, plinth and at ground level excluidng cost of form work 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size).

Providing and laying nominal mix cement concrete with crushed stone aggregate using concrete mixer in foundation, plinth and at ground level excluidng cost of form work M-20 Grade

Providing and laying nominal mix cement concrete with crushed stone aggregate using concrete mixer in foundation, plinth and at ground level excluidng cost of form work M-25 Grade

Providing and laying nominal mix cement concrete with crushed stone aggregate using concrete mixer in foundation, plinth and at ground level excluidng cost of form work M-30 Grade

Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Extra for precast PCC/ RCC work of any mix including form work, hoisting and fixing in Cement Mortar. 1:2 (1 Cement : 2 coarse sand) and finishing with cement plaster in Cement Mortar 1:3 (1 Cement : 3 coarse sand) but excluding reinforcement.

Water proofing material: Providing and mixing water proofing material in PCC/ RCC work in the proportion recommended by the manufacturer.

Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire all complete: Thermo-Mechanically treated Bars FE 500D

Providing and fixing formwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Foundations, footings, base of columns and plinth beam in any shape and size.

Providing and fixing formwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Columns, Pillars, Piers and likes- rectangular or square in shape

Providing and fixing formwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ)

Providing and fixing formwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Beams, lintels, cantilevers & walls

Providing and fixing formwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Stair cases of all types excluding spiral and folded plate type, including risers and landings

DPC: Providing and laying damp proof course (upto 50mm thick) with plain cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20mm nominal size) including formwork.

Applying a coat of hot bitumen VG-10 using @ 1.7kg/ sqm on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Diluting chemical emulsion (chlorpyrifos/ lindane) in water as per manufacturers recommendation and injecting for pre-constructional curative cum preventive anti-termite treatment:(Five year service guarantee bond to be signed by contractor) Surface treatment by spreading emulsion under floor, over the plinth area before laying base concrete @ 5 litres / sqm

Diluting chemical emulsion (chlorpyrifos/ lindane) in water as per manufacturers recommendation and injecting for pre-constructional curative cum preventive anti-termite treatment:(Five year service guarantee bond to be signed by contractor) Treatment of inside of plinth masonry wall on using diluted chemical emulsion @ 1.5 litre per hole, including drilling 12 mm diameter holes in plinth wall below plinth protection at the interval of 300 mm and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand).

Diluting chemical emulsion (chlorpyrifos/ lindane) in water as per manufacturers recommendation and injecting for pre-constructional curative cum preventive anti-termite treatment:(Five year service guarantee bond to be signed by contractor) Treatment of outer side of plinth masonrywall using diluted chemical emulsion @ 1.5 litre per hole, including drilling 12 mm diameter holes in plinth wall at the junction of floor at the interval of 300 mm and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand).

Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in: Cement Mortar 1:6 (1 cement : 6 coarse sand)

Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Half brick thick brick masonry with fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in superstructure above plinth level upto plinth level: Cement Mortar 1:3 (1 cement : 3 coarse sand)

Extra for providing and placing in position hopping 25x1.60 mm or 2 Nos 6mm dia MS bars reinforcement at every third course of half brick masonry.

Providing and making 18 mm thick cement plaster with under layer of 12mm thick cement plaster 1:5 (1 cement : 5 fine sand) finished with a top layer of 6mm thick cement plaster 1:3 (1 cement : 3 fine sand).

Providing and making 18mm thick cement plaster in two coats with under layer of 12mm thick plaster 1:5 (1 cement : 5 fine sand) and top layer of 6mm thick with cement plaster 1:3 (1 cement : 3 fine sand) finished rough with sponge.

Extra for providing and mixing water proofing materials in cement plaster work in proportion as recommended by manufacturer.(PODWER)

Providing flanged joints to double flanged C.I./ D.I. pipes, valves and specials including rubber insertion 3mm thick, suitable bolts and nuts and testing of joints complete: 100 mm diameter pipe

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design: With 20x20 mm square bar

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and fixing in position precast R.C.C. manhole cover and frame L D- 2.5 of required shape and approved quality Rectangular shape 600x450mm internal dimensions

Providing and fixing in position precast circular 560mm internal dia SFRC/ R.C.C. manhole cover or cover and frame of approved quality: Cover and frame H D - 20

Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix: In Cement Mortar 1:4 (1 cement : 4 fine sand)

Providing and making 12mm thick cement plaster of mix: In Cement Mortar 1:4 (1 cement : 4 fine sand)

6mm thick cement plaster of mix: (ceiling) In Cement mortar 1:3 (1 cement : 3 fine sand)

Providing and applying 2mm thick white cement based Acrylic grade putty with minimum 3 coats applied @ 4.0 kg/ 105qm as per relevant IS code 175-45:2021 (Product such as Asian trucare, Berger Happy walls Putty, Birla Opus One pro smooth) to make the surface smooth and even with all tools tackles and labour etc. complete for the work. (This Item to be use in heigher grade painting work Item no.14.65)

Providing and applying Luxury plastic emulsion paint with roller application minimum three coats applied 1.25 lit/105qm up to final finish as per relevant Type - Class D, C, B & A (Glossy /Semi Glossy and Mati, Egg Shell or Satin finish) of required shade (Product such as Asian Royale Shyne, Dulux Velvet Touch, Berger Silk Luxury Emulsion, Nippon Impression Pearl Opus Pure Elegance) inclusive of providing sbro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etu, complete for the work. (with 4 Years Warranty)

Providing and applying on exterior surface with PREMIUM Exterior emulsion paint of required shade to give protective and water proof finish minimum 3 coats applied @ 1.40 lit/105qm up to final finish as per relevant LS. Code 15489:2013 Type -2 Class D, C (Glossy /Semi Glossy finish) (Product such as Asian Apex Dulux Weather Shield Prima E900, Berger Weathercoat Antidust, Nerolac Everlas Excel, Nippon Sumo Eira, Opus True flex) inclusive of providing abro tape on edges and articleand cleaning of door. windows, floor and surface as sequired with all tools tackles and labour etc complete for the work. (With 3Year Warranty.)

Providing and fixing chicken mesh weighting not less than 250 gms/sqm as per IS : specification in the required width with 40mm long steel nails on vertical and horizontal surface near R.C.C. and brick wallsjunctions including scaffolding and all lead and lifts etc. complete before plastering upto 10mts in height.

Providing and Laying Matt/Glazed finish HOMOGENEOUS ACROSS FULL BODY VITRIFIED floor tiles (heavy duty) with water absorption less than 0.05% and conforming to IS: 15622-2017 of 1st quality of approved make in all colours and shades and size mentioned below (+/- 10mm), laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. Size 600x600mm thickness 9 to 10mm

15 mm thick Table rubbed polished Granite stone slab flooring laid over 20mm (Average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing etc. complete. (Area of slab should be 0.50 sqm and above) Granite stone black

Providing and laying ceramic glazed floor tiles conforming to IS : 15622 of approved size, make, colour, shade laid on 20 mm thick Cement Mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement mixed with matching pigment etc., complete. Size 300x300mm

Providing and fixing ceramic glazed wall tiles conforming to IS : 15622 of approved make, colours, shades and size on wall and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with matching pigment complete. Size above 200x300mm

15 mm thick Table rubbed polished Granite stone slab in risers and treads of steps skirting dado and pillars laid on 12mm (Average) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry including rubbing and polishing etc. complete (single stone is to be used for risers and treads of steps and width of stone for skirting and dado shall be equal to the height of skirting & dado and length of 1.0 m). Granite stone black

15mm thick Granite work (machine cut, table rubbed & mirror polished) for kitchen platform, vanity counters, window sills and similar locations of required size laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) including joints treated with white cement mixed with matching pigment including rubbing and polishing to edge moulding to give high gloss finish. Granite stone black

Extra for nosing in Granite stone for treads.

Providing and fixing 15mm thick Granite (machine cut, table rubbed & mirror polished on both sides) for partition curtain in toilets or similar locations of required size in wall with cement mortar 1:4 (1 cement : 4 coarse sand) including cutting chase in wall and joint with wall treated with white cement mixed with matching pigment including rubbing and polishing to edge moulding to give high gloss finish. Granite stone black

Plinth protection: Making 50mm thick plinth protection of plain cement concrete 1:3:6 (1cement : 3 coarse sand : 6 graded crushed stone aggregate 20mmnominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with sand including finishing the top smooth.PCC

Providing and fixing in position doors, windows and ventilators frames made of cold rolled pressed steel sheet framed profiles made from commercial M.S. Sheets conforming to I.S. 513 of 1973 and as per general specifications of I.S 4351 including hinges jamb, lock jamb, steel butt hinges, base tie, joints mitred and welded with 10cm long legs of size 15x3mm M.S. flat, embedded in cement concrete blocks 15x10x10cm size of grade M-10 or rawl plugs and screws or with fixing clips or with bolts and nuts including neatly compacted filling M-10 cement concrete in profile section applying a priming coat of red oxide zinc chromate primer. Single rebate/ mullion 100mmx50mm size, 1.6mm thick sheet

Providing and fixing flush door shutters, conforming to IS 2202 (Part 1), interior grade, commercial type, core of block board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains, cross bands and face veneers on both faces of shutters excluding hinges. 35 mm. thick (single leaf)

Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and direction of Engineer-in-Charge.

Providing and fixing 30mm thick factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for styles and 15x15mm for top & bottom rails. M.S.frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45degree angle on either side forming styles; and 5mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel. 10mm (5mm x 2 ) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per Manufacturer’s specification including 3 nos ISI marked stainless steel hinges of size 100x58x1.9 mm complete. (for W.C. and bathroom door shutter). PVC door shutter

Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat welded to frame with all necessary fitting complete including applying a priming of red oxide zinc chromate primer.

Providing and fixing anodized aluminium framed grill (minimum anodic coating of grade AC 15)of of approved shape, pattern and design including cutting, bending, hoisting and erecting/ fixing to door, window frame or to wall with fixing clips or hold fasteners or bolts and nuts as required etc. complete.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. compl ete. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness

Providing and fixing tinted glass panes with steel glazing clips and special metal sash putty of approved make in steel doors, windows, ventilators: 4 mm thick

Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) conforming to IS: 733, IS: 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing to be paid for separately: For shutter of doors, windows & ventilators including providing and making provision for fixing of fitting wherever required including the cost of PVC/neoprene gasket required (Fittings shall be paid for separately).

Extra for providing and fixing tinted glass panes in aluminium door,window, ventilator shutters and partitions instead of float glass. 4 mm thickness

Providing and fixing antique/ SS finished brass butt hinges with antique/SS polished MS screw complete: 125x85x5.50mm (Heavy Type)

Providing and fixing antique/ SS finished brass door latch with antique/ SS polished MS screw complete: 300 x16x5 mm

Providing and fixing antique/ SS finished brass tower bolts (Barrel type) with antique/ SS polished MS screw complete: 250 x10 mm

Providing and fixing antique/ SS finished brass handles with antique/ SS polished MS screw complete: 125mm

Providing & fixing 150mm antique/ SS finished brass floor door stopper with rubber cushion and antique/SSpolished MS screw complete to suit the shutter thickness.

Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc complete.

Providing and fixing M.S. fan clamp/hook for ceiling fan made out of 16mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs, beams during laying including painting the exposed portion of loop.

Providing stainless steel railing/ grill made of S.S. flats, hollow S.S. pipe or square/ rectangular sections of approved design fixing in stair case, balcony or other places with metal fasteners and stainless steel bolts etc complete. SS Grade 304

Providing and fixing approved pipe hand rail by welding to iron railing including applying a priming coat of red oxide zinc chromate primer. M.S Pipe

Providing and applying priming coat on steel work with red oxide/ zinc phosphate primer applied @ 0.50 lit /Sqm as per relevant code 3536:1999 ( product such as Asian Zinc phosphate, Dulux Steel primer, Burger Red oxide primer) with all tools tackles and labour etc. complete for the work.

Providing and making moulded mortar band in cement mortar 1:4 (1 cement : 4 fine sand) per cm width: 18 mm thick

Making grove in cement plaster while plastering upto10 mm deep and 10 mm wide.

Providing and fixing false ceiling at all heights with 15mm thick integral densified tegular edged light weight calcium silicate false ceiling tile reinforced with fibre and natural filler false ceiling tiles of size 595x595xmm of approved testure, design and paterns (such as cosmos, spinton, quatra, golb) having NRC (Noise Reducation coefficient) of 0.50 (minimum) as per IS : 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS: 476 (part-4), fire performance as per BS:476 (part 6 & 7), humidity resistance of 100%, thermal conductivity 0.048 to 0.050 W/m0KC as per ASTM 518:1991, Weight 1.900 Kg to 2.100 Kg per tile, 15 MM Edge Density Having 450 Kg/cum & 10 mm Central Portion of tile having 350 Kg/cum. in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33 mm thick (galvanized @120 grams per sqm including both sides) comprising of main T runners of size 24x38 mm of length 3000mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermedicate cross -T of size 24x32 mm of length 600mm to form grid module of size 600x600mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 40mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000 mm length & L-shape level adjuster of size 85x25x25x2mm Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000mm to be fixed on periphery wall/ partition with the hep of plastic rawl plugs at 450mm center to center and 40mm long dry wall S.Sscrews. The work shall be carried out as per specifications, drawings and as per directions of the Enginer-In-Charge Ceiling height up 3.5mt from adjacent floor level extra height to be paid separately.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (UV stabilized, Nitrile Insulation) 20 mm nominal outer dia .Pipes. (DWS)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (UV stabilized, Nitrile Insulation) 32 mm nominal outer dia .Pipes. (DWS)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (UV stabilized, Nitrile Insulation) 50 mm nominal outer dia .Pipes. (up water) (DWS)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. EXTERNAL WORK 100mm nominal inner dia pipes

Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete. 75 mm dia pipe (for waste water)

Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete. 110 mm dia (for Sewerage)

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Tee/ Tee with door/ Bend 45°/ Bend 90° 75 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Tee/ Tee with door/ Bend 45°/ Bend 90° 110 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Double "Y" with or without door 75 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Double "Y" with or without door 110 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Vent covel 110 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Access door cap 75 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Access door cap 110 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. P trap 110mmx110mm long

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Nahani trap 110x75mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Multi floor trap 110

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Plain reducing Tee 110x75mm

Providing and fixing vitreous china water closet (European type W.C. pan) with white ISI marked plastic seat and lid, 10 litre low level white P.V.C. flushing cistern (same colour), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : Coloured pedestal type

Providing and fixing water closet squatting pan (Indian type W.C. pan ), 100mm sand cast Iron P or S trap, 10 litre low level P.V.C. flushing cistern (same colour) conforming to IS : 7231, with flush bend and other fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing white vitreous china urinal basin with waste fitting as per IS : 2556, and other couplings in C.P. brass complete: Flat back half stall urinal of size 460x380x250mm

Providing and fixing vitreous china wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of brackets, cutting and making good the walls wherever required : White Oval or round size 550x400mm

Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32 mm dia

Providing and fixing 15 mm nominal bore Brass bib/stop cock of approved quality: Bib cock (350 grams)

Providing and fixing 15 mm nominal bore Brass bib/stop cock of approved quality: Stop cock (350 grams)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Long nose bib cock (500gms)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Wall mixer with elegant knob (1400 grams)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Bottle trap set with extension pipes

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Toilet paper holder

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Soap dish plate

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Shower rose (revolving type) (150mm)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Towel rail (600mm long x 20mm dia)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Towel ring (150 mm dia)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Health foscet (hand jet) with flexible connection pipe (for WC)

Providing and fixing stainless steel drain jali of approved make/quality.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

Providing and fixing brass/ gun metal gate valve with C.I. wheel of approved quality (screwed end): 32 mm nominal bore

Providing and fixing brass/ gun metal gate valve with C.I. wheel of approved quality (screwed end): 50 mm nominal bore

Providing and fixing gun metal non- return valve (horizontal type) of approved quality (screwed end) : 50 mm nominal bore

Providing and fixing brass GM/ ball valve (full bore type) with plastic coated lever and screwed female ends tested to 20 Kg/ cm2 of approved quality as specified. 25 mm dia

Providing and fixing brass GM/ ball valve (full bore type) with plastic coated lever and screwed female ends tested to 20 Kg/ cm2 of approved quality as specified. 50 mm nominal bore

Providing and fixing 600x450 mm beveled edge 4mm mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5mm glass shelf with edges rounded off supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : For 100 mm dia pipe

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. : For 75 mm dia pipe

Constructing masonry Chamber 30x30x50 cm, inside with fly ash bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design :

Constructing masonry Chamber 60x60x75 cm, inside with modular well burnt clay bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate

Constructing masonry Chamber 90x90x100 cm, inside with modular well burnt clay bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm. top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :

Supply, erection, jointing, testing & commissioning of "C" Class MS pipes (as per IS: 1239) including necessary specials such as tees, bends, flanges reducers etc., complete on wall/ ceiling. The pipes to be erected on wall or suspended from beams, RCC roof slabs with suitable size MS bars/ angle irons including painting of metal part except pipe line. 50mm dia.

Supply, erection, jointing, testing & commissioning of "C" Class MS pipes (as per IS: 1239) including necessary specials such as tees, bends, flanges reducers etc., complete on wall/ ceiling. The pipes to be erected on wall or suspended from beams, RCC roof slabs with suitable size MS bars/ angle irons including painting of metal part except pipe line. 80mm dia.

Supply, erection, jointing, testing & commissioning of "C" Class MS pipes (as per IS: 1239) including necessary specials such as tees, bends, flanges reducers etc., complete on wall/ ceiling. The pipes to be erected on wall or suspended from beams, RCC roof slabs with suitable size MS bars/ angle irons including painting of metal part except pipe line. 100mm dia.

Supply, erection, jointing, testing & commissioning of "C" Class MS pipes (as per IS: 1239) including necessary specials such as tees, bends, flanges reducers etc., complete on wall/ ceiling. The pipes to be erected on wall or suspended from beams, RCC roof slabs with suitable size MS bars/ angle irons including painting of metal part except pipe line. 150mm dia.

Painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. 50mm dia.

Painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. 80mm dia.

Painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. 100mm dia.

Painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. 150mm dia.

Providing and fixing on wall surface G.I. pipes medium class complete with G.I. fittings and clamps, including cutting, making good the walls etc. and testing of joints complete: 25 mm dia. nominal bore

Providing and wrapping 4 mm thick of approved make and quality bitumen based anti rust felt over MS pipe with overlap of 25 mm to make an impermeable layer including painting with one coat of bitumastic paint before felt complete. (Only on MS pipe to be laid in soil below ground). 150mm dia. pipe

Providing and wrapping 4 mm thick of approved make and quality bitumen based anti rust felt over MS pipe with overlap of 25 mm to make an impermeable layer including painting with one coat of bitumastic paint before felt complete. (Only on MS pipe to be laid in soil below ground). 100mm dia. pipe

Providing and wrapping 4 mm thick of approved make and quality bitumen based anti rust felt over MS pipe with overlap of 25 mm to make an impermeable layer including painting with one coat of bitumastic paint before felt complete. (Only on MS pipe to be laid in soil below ground). 80mm dia. pipe

Providing, installation, testing and commissioning of dual plate non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required. 100mm dia

Providing, installation, testing and commissioning of dual plate non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required. 150mm dia

Supplying, fixing, testing and commissioning of flanged butterfly valve PN 1.6, with Bronze/Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, conforming to IS: 13095 of following sizes as required. 100mm dia

Supplying, fixing, testing and commissioning of flanged butterfly valve PN 1.6, with Bronze/Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, conforming to IS: 13095 of following sizes as required. 150mm dia

Providing, fixing, testing and commissioning 50mm dia drain system in wet riser line with 50mm dia GM valve, necessary MS "C" class pipe line (upto 1 metre) and accessories complete as required.

Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia and with necessary G.I. coupling, valve to be fitted on top of Air vessel or on wet riser as per specification.

Providing and fixing pressure switch with suitable for 1-10 Kg/cm2 including 12/15 mm Ø isolation valve, G.I. nipple, elbow, electrical connections setting of Cut-In and cut-Off pressure complete in all respects and in an approved manner.

Supplying and installing pressure gauge of 100 mm Ø., 0-300 PSI or 0-21 kg per cm square fitted with 12/15 mm Ø. pad cock valve, and G.I. pipe, elbow etc. as per requirement in approved manner.

Supplying and fixing swinging type First-Aid Hose Reel drum with MS construction spray painted in Post office Red colour, conforming to IS: 884 with upto date amendments, complete with brackets for fixing on wall, connections from riser with 25 mm dia MS/GI pipe and GM gate valve but excluding hose reel.

Supplying and fixing single headed internal hydrant valve with instantaneous Gun metal couplings of 63 mm dia with cast iron wheel ISI marked conforming to IS: 5290 (Type - A) with blank Gunmetal cap and chain as required.

Supplying and erecting orifice plate having 6 mm thickness, 140 mm outer dia at every single outlet hydrant valve as per specification.

Supplying and fixing 63 mm dia, 15 mtr long RRL hose pipe with 63 mm dia Male and Female Stainless Steel-IS: 3444 Grade-1 couplings duly binded with GI wire, rivets etc. conforming to IS: 636 (Type -A) as required.

Supplying and fixing of MS hose cabinet box of made of 2 mm thick MS sheet and 40 x 40 x 5mm angle iron with front openable cover having 6 mm thick glazed glass viewing window i/c necessary locking arrangement, on existing wall/ brick platform etc complete as required. Size 600 mm x 600 mm x 500 mm

Providing and fixing fire brigade 63mm dia GM suction coupling to 100/150 mm dia suction pipe complete.

Providing and fixing M.S. structural work fabricated from standard sections, (MS rounds, angles, channels etc.) including cutting to size, drilling welding including cost of steel fasteners, clamp in RCC structural members as directed, including two coat of enamel painting over one coat of red oxide primer complete.

Supplying and fixing 4 way Fire Brigade Connection of cast iron body with 4 Nos. Gun metal male instantaneous inlet couplings complete with cap and chain conforming to IS: 904 including connection to existing MS pipe line complete as required.

Supplying, filling, spreading & leveling stone boulders/ Gravels/ Coarse sand, in recharge pit, in the required layers and thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. (excavation of pit will be paid separately). Gravels of size range 5 mm to 10 mm, over the existing layer of boulders

Boring/drilling bore well perfectly vertical for the specified depth suitable to receive required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer–in-charge upto 90 metre depth below ground level. All types of soil 200mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer –in-charge 150 mm nominal size dia.

Gravel packing in tube well construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for bore well of: 150 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tube well as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 150 mm clamp.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tube well as per IS:2800 (part I). 150 mm dia

Supplying and stacking of good earth at site including royalty, loading, unloading and carriage upto 5 km (earth measured in stacks will be reduced by 20% for payment).

Grassing with ‘Doob’ grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing including supplying good earth if needed (the good earth shall be paid for separately). In rows 5 cm apart in either direction.

Providing and planting following herbs in garden including preparation of soil, base plantation, providing and spreading different fertilizers, soil and sand: Hedges like Alife, Dorenta, Tikoma etc

Providing and planting following herbs in garden including preparation of soil, base plantation, providing and spreading different fertilizers, soil and sand: Furn like Arica, China etc (3 year old

Providing and planting following herbs in garden including preparation of soil, base plantation, providing and spreading different fertilizers, soil and sand: Hibiscus (Flower)/ Rose

Providing and planting following herbs in garden including preparation of soil, base plantation, providing and spreading different fertilizers, soil and sand: Carpet grass (well developed)

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 60 cm dia, and 60 cm deep.

Supply, installation, testing & commissioning of solar water heating system with heat exchanger type including electrical heater backup,make up water tank but without piping

Excavation in Soil (by Mechanical Means.) Excavation for roadway in soil using mechanical means including loading in tipper for carrying of cut earth to embankment site and unloading with all lifts and lead as per relevant clauses of section 300.

Granular Sub-base as per Table:- 400-1 Construction of granular sub-base by providing close graded Material, , carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface watering, rolling and compacting with vibratory power roller at OMC to achieve the desired density, complete as per clause 401 .A Plant mix method (with Mechanically crushed stone only) (a) For Sub-base cum drainage layer or upper sub-base with (i) Grading-III Material

Dry Lean Cement Concrete Sub-base as per IRC:SP-49 (Construction of dry lean cement concrete Sub-base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 26.5 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days,mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing as per clause 601.)

Providing and Laying Un-reinforced cement concrete without Dowel bars including formwork and expansion contraction & Longitudinal joints as per desing and as per IRC62-2014 over a prepared base as per approved mix design and finishing to lines and grade as per drawing for pavement thickness less than 200mm in low volume roads (I) PCC Grade M30 with minimum Cement Content @ 375kg/cum

"Retro-reflectorized Traffic signs as per Clause 801. Providing and fixing of retro-reflectorized cautionary, mandatory and informatory sign over retro-reflective sheeting of required grade confirming to ASTM D 4956 as per IRC:67-2022 made of retro-reflective type sheeting fixed over Aluminium Sheeting/Aluminium Composite Material (ACM) sheeting including application of fluorination coating applied on exposed surfaces of aluminium to ensure corrosion resistance, supported on a mild steel base frame of ISA 40 x 40 x 6 mm and mild steel angles for post 75 mm x 75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, as per approved drawing and painting all exposed components of the signs and supports with primer and 2 coats of epoxy paint or powder coating and the part of post below ground shall be painted with 3 coats of redoxide paint as per clause 7.2 of IRC:67-2022. (Note: The details of manufacturer, type of sheeting, month and year of installation, project details and other details along with QR code as detailed in clause 13.2 and Annexure-VII of IRC:67-2022 shall be printed on back side of the sign board.)" With Aluminium sheeting "Made of Class-A High Intensity Micro Prismatic Engineering Grade Sheeting of Type I confirming to Table 6.3 of IRC:67-202 "With Aluminium sheeting of 2 mm & 1.5 thickness" 90 cm equilateral triangle (2.0 mm thick)

"Retro-reflectorized Traffic signs as per Clause 801. Providing and fixing of retro-reflectorized cautionary, mandatory and informatory sign over retro-reflective sheeting of required grade confirming to ASTM D 4956 as per IRC:67-2022 made of retro-reflective type sheeting fixed over Aluminium Sheeting/Aluminium Composite Material (ACM) sheeting including application of fluorination coating applied on exposed surfaces of aluminium to ensure corrosion resistance, supported on a mild steel base frame of ISA 40 x 40 x 6 mm and mild steel angles for post 75 mm x 75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, as per approved drawing and painting all exposed components of the signs and supports with primer and 2 coats of epoxy paint or powder coating and the part of post below ground shall be painted with 3 coats of redoxide paint as per clause 7.2 of IRC:67-2022. (Note: The details of manufacturer, type of sheeting, month and year of installation, project details and other details along with QR code as detailed in clause 13.2 and Annexure-VII of IRC:67-2022 shall be printed on back side of the sign board.)" With Aluminium sheeting "Made of Class-A High Intensity Micro Prismatic Engineering Grade Sheeting of Type I confirming to Table 6.3 of IRC:67-202 "With Aluminium sheeting of 2 mm & 1.5 thickness" 60 cm equilateral triangle (1.5mm thick)

"Retro-reflectorized Traffic signs as per Clause 801. Providing and fixing of retro-reflectorized cautionary, mandatory and informatory sign over retro-reflective sheeting of required grade confirming to ASTM D 4956 as per IRC:67-2022 made of retro-reflective type sheeting fixed over Aluminium Sheeting/Aluminium Composite Material (ACM) sheeting including application of fluorination coating applied on exposed surfaces of aluminium to ensure corrosion resistance, supported on a mild steel base frame of ISA 40 x 40 x 6 mm and mild steel angles for post 75 mm x 75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, as per approved drawing and painting all exposed components of the signs and supports with primer and 2 coats of epoxy paint or powder coating and the part of post below ground shall be painted with 3 coats of redoxide paint as per clause 7.2 of IRC:67-2022. (Note: The details of manufacturer, type of sheeting, month and year of installation, project details and other details along with QR code as detailed in clause 13.2 and Annexure-VII of IRC:67-2022 shall be printed on back side of the sign board.)" With Aluminium sheeting "Made of Class-A High Intensity Micro Prismatic Engineering Grade Sheeting of Type I confirming to Table 6.3 of IRC:67-202 "With Aluminium sheeting of 2 mm & 1.5 thickness" 80 cm x 60 cm rectangular (2.0 mm thick)

"Retro-reflectorized Traffic signs as per Clause 801. Providing and fixing of retro-reflectorized cautionary, mandatory and informatory sign over retro-reflective sheeting of required grade confirming to ASTM D 4956 as per IRC:67-2022 made of retro-reflective type sheeting fixed over Aluminium Sheeting/Aluminium Composite Material (ACM) sheeting including application of fluorination coating applied on exposed surfaces of aluminium to ensure corrosion resistance, supported on a mild steel base frame of ISA 40 x 40 x 6 mm and mild steel angles for post 75 mm x 75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, as per approved drawing and painting all exposed components of the signs and supports with primer and 2 coats of epoxy paint or powder coating and the part of post below ground shall be painted with 3 coats of redoxide paint as per clause 7.2 of IRC:67-2022. (Note: The details of manufacturer, type of sheeting, month and year of installation, project details and other details along with QR code as detailed in clause 13.2 and Annexure-VII of IRC:67-2022 shall be printed on back side of the sign board.)" With Aluminium sheeting "Made of Class-A High Intensity Micro Prismatic Engineering Grade Sheeting of Type I confirming to Table 6.3 of IRC:67-202 "With Aluminium sheeting of 2 mm & 1.5 thickness" 60 cm Circular (1.5mm thick)

Providing and planting of 3‟0” to 4‟0” heighted Ficus prestige/Blackiana plants with 1‟6” x 1‟6” depth pit formation and soil preparation, (Mixing organic manure and plant‟s protection insecticide). Up to 4 month maintenance after work completed and as direction of engineer in charge

Providing and planting of 4‟0” to 5‟0” heighted Ficus prestige/Blackiana plants with 1‟6” x 1‟6” depth pit formation and soil preparation, (Mixing organic manure and plant‟s protection insecticide). Up to 12 month maintenance after work completed and as direction of engineer in charge

Providing and planting of Bogenbelia dwarf, chandni dwarf, kaner dwarf vr flower bearing plants with 0‟9” x 0‟9” depth pit formation and soil preparation work‟s, (Mixing organic manure and plant‟s protection insecticide). ( Nicodia,Euphorbia milii). Up to 12 month maintenance after work completed and as direction of engineer in charge

Providing and planting of dwarf red Ekalyha plants showing mass effect view with 0‟9” x 0‟9”x1‟0” depth pit formation and soil preparation work‟s, (Mixing organic manure and plant‟s protection insecticide). Up to 12 month maintenance after work completed.

Providing and planting of Golden durenta multi branches plants for showing mass effect in 0‟6” x 0‟6” distance with soil preparation work‟s, (Mixing organic manure and plant‟s protection insecticide). Up to 12 month maintenance after work completed and as direction of engineer in charge

Planting of Trees and their maintenance for one year (Planting of trees by the row side(Avenue trees) in 0.60m dia.holes, 1m. Deep dug in the ground, mixing the soil with decayed farm yard/sludge manure,planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year

Providing, laying, jointing, testing and commissioning of D.I Dismantling joint with M.S. Nut stud & washers coated for rust prevention & internal rubber rings etc. complete assembly set as per type design inclusive of all taxes & duties, insurance, loading/ unloading & stacking FOR at site all complete as per technical Specifications and as per direction of Engineer. 80mm diameter

Providing, laying, jointing, testing and commissioning of D.I Dismantling joint with M.S. Nut stud & washers coated for rust prevention & internal rubber rings etc. complete assembly set as per type design inclusive of all taxes & duties, insurance, loading/ unloading & stacking FOR at site all complete as per technical Specifications and as per direction of Engineer. 100mm diameter

Providing, laying, jointing, testing and commissioning of D.I Dismantling joint with M.S. Nut stud & washers coated for rust prevention & internal rubber rings etc. complete assembly set as per type design inclusive of all taxes & duties, insurance, loading/ unloading & stacking FOR at site all complete as per technical Specifications and as per direction of Engineer. 150mm diameter

Providing, hoisting and fixing in position inverted „J‟ type 100 mm dia. C.I. Cowl type ventilators with mosquitoproof aluminium mesh at top including applying 2 coats of anti-corrosive paint, etc. complete as directed by Engineer-in-charge, weighing not less than 35 Kg.

Providing, laying and jointing followings ISI marked O-PVC (Oriented uplasticized polyvinyl chloride) ring fit type pipe having orientation class 500 (IS 16647) with integral homogeneous spigot having elastomeric seeling ring made of EPDM rubber (one per pipe) including testing of joint, cost of jointing materials etc. complete in all respect. Presure Rating as per IS Code – IS: 16647:2017, PN-16 110 mm dia

Providing, laying and jointing followings ISI marked O-PVC (Oriented uplasticized polyvinyl chloride) ring fit type pipe having orientation class 500 (IS 16647) with integral homogeneous spigot having elastomeric seeling ring made of EPDM rubber (one per pipe) including testing of joint, cost of jointing materials etc. complete in all respect. Presure Rating as per IS Code – IS: 16647:2017, PN-16 160 mm dia pipe.

Providing, laying and jointing followings ISI marked O-PVC (Oriented uplasticized polyvinyl chloride) ring fit type pipe having orientation class 500 (IS 16647) with integral homogeneous spigot having elastomeric seeling ring made of EPDM rubber (one per pipe) including testing of joint, cost of jointing materials etc. complete in all respect. Presure Rating as per IS Code – IS: 16647:2017, PN-16 200 mm dia

Providing and laying mechanically mixed cement concrete with crushed stone aggregate excluding centering and shuttering (with 40mm nominal size graded stone aggregate) 1:3:6 (M-10)

Supplying & Installation of Five star BEE rating ISI Marked required capacity of Three phase, 50 Hz, 415V, Open well Submersible pump, with Control Panel Starter with Dry Run Protection, single phase preventer, connections, etc. as required as per specifications but excluding pipe and connectioncable. 3.0 H.P. Head Mt.15-30, Discharge LPM 615-195

Fabrication of M.S. Pipes and Specials : Fabrication of M.S. pipes & specials as per IS specifications with inside & outside epoxy coating as per relevant IS code, duly tested for usage in Drinking water inclusive of all materials, Central, State and Municipal taxes and duties inspection charges, transit insurance, loading /unloading FOR site unloading & stacking etc. complete in all respect as per technical specification and as per direction of Engineer NRANVP. Fabricating pipes from steel plates (all thickness) 5 to 8 mm

Providing & fixing cast iron butterfly valves including jointing & testing with cost of jointing material such as bolts, nuts and rubber insertion all complete as per IS:13095-1991. (Valvesabove 200 mm dia should be gear operated) 80 mm dia. PN-1.6.

Providing & fixing cast iron butterfly valves including jointing & testing with cost of jointing material such as bolts, nuts and rubber insertion all complete as per IS:13095-1991. (Valvesabove 200 mm dia should be gear operated) 150 mm dia. PN-1.6.

Providing and fixing following cast iron double flanged single door reflux (non return) valve including jointing and testing with cost of jointing material such as bolts, nuts and rubber insertion all complete as per IS:5312 9 (Part I) 80 mm dia. (Class -PN 1.0 rating)

Supply of DI Dismantling joint with M.S. Nut stud & washers coated for rust prevention & internal rubber rings etc. complete assembly set as per type design inclusive of all taxes & duties, insurance, loading/ unloading & stacking FOR at site complete. 80 mm dia.

Providing & fixing cast iron double air valves, flanged without in-built isolating valve as per IS:14845-2000 including jointing & testing with cost of jointing material and rubber insertion all complete as per IS :13095-1991 80mm dia PN-1.6

Supply & Fixing ISI marked (IS:2878) Portable fire Extinguisher, Carbon-dioxide type flat base including valve, discharge hose of not less than 10 mm dia. min. 600 mm long & complete in all respects including initial fill with C02 gas confirming to IS:307-1966 filled to a filling ratio of not more than 0.667and wall suspension bracket. Capacity 4.5 Kg

Supply & Fixing ISI marked (IS:10204) Poratable Fire Exitnguisher,Trolley mounted Mech. Foam type capacity 09 ltrs with gun-metal cap and nozzle and complete respects in all respects including initial fill and wall suspension. Capacity 9.0 ltrs

Providing and erecting floor mounted sand/ water bucket stand for keeping 4 nos. of fire bucket, 1500 mm in length and 900 mm in height made out of 30 X 30 X 4 mm angle iron welded with 4 hooks and duly painted with one coat of zinc cromate primer and 2 coat of synthetic enamel paint of post box red colour etc complete.

Supplying G.I. Fire buckets with round bottom having at least 9 lit. capacity duly painted with one coat of zinc cromate primer and 2 coat of synthetic enamel paint of post box red colour and filled with dry sand and kept on provided wall hook or stand etc complete.

Supplying , installation , testing and commissioning of Fire alarm Control panel (UL Listed) suitable for 252 addressable points (Detector & Devices). Comprising of the following system components: Operating units, Periphery boards, Power supplies,System enclosures, with battery backup 24hours and 30minutes,

Supplying , installation , testing and commissioning of Intelligent Addressable Type Manual Call Point:Intelligent Manual Fire Alarm Box is constructed of durable, molded and polycarbonate material that is matte finished in red with raised white lettering Single-action,Pull-down lever is down, until manually reset,Polarity insensitive via SureWireTM technology

Supplying , installation , testing and commissioning of Short circuit Isolator Base:Local light-emitting diode (LED) indicator UL 864 9th Edition Listed and ULC Listed; FM Approved

Supplying , installation , testing and commissioning of Response Indicator for above false ceiling detector

Supplying , installation , testing and commissioning of Intelligent Addressable Relay control module for Hooter Interfacing and supervising normally open (N.O) or normally closed (N.C) contacts,Integral single-pole, double-throw (SPDT) relay (up to 4 amps) ,Multi-color light-emitting diode (LED) indicates system status, UL Listed & ULC Listed; FM Approved

Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade in exiting PVC/ GI pipe etc as per specification and IS: 694 (2010) 2 core 1.5 Sqmm

Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade in exiting PVC/ GI pipe etc as per specification and IS: 694 (2010) 4 core 2.5 Sqmm

Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) & IS: 7098 (1988, Part 1) 4 x 16 sq. mm.

Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) & IS: 7098 (1988, Part 1) 2 x 10 sq. mm

Supplying and making end termination with brass compression gland and aluminum lugs for following size armoured aluminum conductor power cable of 1.1 KV grade as per specification. 4 X 16 sq. mm (22 mm)

Supplying and making end termination with brass compression gland and aluminum lugs for following size armoured aluminum conductor power cable of 1.1 KV grade as per specification. 2 X 10 sq. mm (19 mm)

Design, Fabrication, Supply, Erection, Testing and commisioning of Powder coated, Weather Proof Double door type Feeder pillar fabricated out of 14 guage CRCA sheet steel in cubical, free standing, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Feeder pillar shall be treated with all anti-corrosive process before painting as per specification. Feeder Pillar shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated)- Feeder Pillar: INCOMER- 1No.63A FP MCCB(35 KA), Metering & Indication- 1 set of phase indicating lamps BUS-BAR- 1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves. OUTGOINGS- 1 Nos.32A FP MCB & 2 Nos.32A SP MCB

Point Wiring for light/ fan/ exhaust fan/ call bell point with 1.5 sqmm FRLS PVC insulated stranded copper conductor single core cable in concealed FRLS PVC conduit, with 6 A modular switch ,modular base and cover plate with suitable size GI. box and earthing the point with same size cable along with accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards ,Electrical Inspectorate standards.Short Point

Point Wiring for light/ fan/ exhaust fan/ call bell point with 1.5 sqmm FRLS PVC insulated stranded copper conductor single core cable in concealed FRLS PVC conduit, with 6 A modular switch ,modular base and cover plate with suitable size GI. box and earthing the point with same size cable along with accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards ,Electrical Inspectorate standards. Medium Point

Point Wiring for light/ fan/ exhaust fan/ call bell point with 1.5 sqmm FRLS PVC insulated stranded copper conductor single core cable in concealed FRLS PVC conduit, with 6 A modular switch ,modular base and cover plate with suitable size GI. box and earthing the point with same size cable along with accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards ,Electrical Inspectorate standardsLong point

Providing and fixing light plug point on board in concealed PVC conduit point wiring with modular type 3 pin 5 amp socket outlet and 5 amp switch including cost of base and cover plate and G. I. box etc. as required

Point wiring for light plug point with 2.5 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 6 A modular switch and 3 pin 6 A modular socket outlet, modular base and cover plate with suitable size GI. box, earthing the switch box and socket outlet with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards.Short Point

Point wiring for light plug point with 2.5 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 6 A modular switch and 3 pin 6 A modular socket outlet, modular base and cover plate with suitable size GI. box, earthing the switch box and socket outlet with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards .Medium Point

Point wiring for light plug point with 2.5 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 6 A modular switch and 3 pin 6 A modular socket outlet, modular base and cover plate with suitable size GI. box, earthing the switch box and socket outlet with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. Long Point

Point wiring for light plug point with 2.5 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 6 A modular switch and 3 pin 6 A modular socket outlet, modular base and cover plate with suitable size GI. box, earthing the switch box and socket outlet with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standardsExtra Long Point I

Point wiring for light plug point with 2.5 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 6 A modular switch and 3 pin 6 A modular socket outlet, modular base and cover plate with suitable size GI. box, earthing the switch box and socket outlet with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standardsExtra Long Point II

Point wiring for Power plug point with 2x4 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 16 A modular switch and 6 pin 6/16 A modular socket outlet,modular base and cover plate with suitable size GI. box earthing the switch box and socket outlet earthing with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. Short Point

Point wiring for Power plug point with 2x4 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 16 A modular switch and 6 pin 6/16 A modular socket outlet,modular base and cover plate with suitable size GI. box earthing the switch box and socket outlet earthing with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards.Medium Point

Point wiring for Power plug point with 2x4 sq mm FRLS PVC insulated stranded copper conductor single core cable cable in concealed FRLS PVC conduit along with 16 A modular switch and 6 pin 6/16 A modular socket outlet,modular base and cover plate with suitable size GI. box earthing the switch box and socket outlet earthing with same size cable along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards.Long Point

Circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in concealed PVC conduit along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3 x 4 sqmm in 25 mm conduit

Circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in concealed PVC conduit along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3 x 1.5 sqmm in 20 mm conduit

Circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in concealed PVC conduit along with accessories, hardwares etc. required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3 x 2.5 sqmm in 20 mm conduit

Supply and fixing of following sizes PVC conduit in concealed manner along with accessories, hardwares etc required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 20mm

Supply and fixing of following sizes PVC conduit in concealed manner along with accessories, hardwares etc required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 25mm

Supply and fixing of following sizes PVC conduit in concealed manner along with accessories, hardwares etc required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 32mm

Supply and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ concealed, steel/ PVC conduit as required. 3 x 1.5 sq.mm. (from Pole Junction box to Light fitting)

Wiring for twin control light point with 1.5 sqmm FR PVC insulated stranded copper conductor single core cable in concealed PVC conduit, with 5 amp modular switch, modular base and cover plate, suitable size G.I. box and earthing the point with same size cable as required for completeness and as per direction of Engineer,CGPWD standards Electrical Inspectorate standards.

Supply and fixing of following modular type switches and accessories of approved make and type such as switch, socket etc on the existing modular plates & switch box including connections along with accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3 pin 5/6 amp socket outlet

Supply and fixing of following modular type switches and accessories of approved make and type such as switch, socket etc on the existing modular plates & switch box including connections along with accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 6 pin 15/16 amp socket outlet

Supply and fixing of following modular type switches and accessories of approved make and type such as switch, socket etc on the existing modular plates & switch box including connections along with accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. Fan Regulator Electronic, step type moving all round

Supply and fixing of following modular type switches and accessories of approved make and type such as switch, socket etc on the existing modular plates & switch box including connections along with accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 5/6 amps one way switch

Supply and fixing of round/hexagonal fan box (125mm dia) depth 75mm (max.) with 12mm dia steel bar hook,1.6mm thick MS sheet cover, in RCC slab along with accessories, hardwares etc as required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards.

Supply and fixing of metal box of following sizes in recess with suitable size phenolic laminated sheet cover in FRLSont including painting, accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 100mm x 100mm x 60mm deep

Supply and fixing of GI box of following sizes in recess with modular base & cover plate for modular switches including accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 125mmx75mm

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, including connection, earthing etc. complete as per specification. 1200mm sweep

Supplying, installation, testing and commissioning of following sizes fancy exhaust fan having built in lovers in existing opening in wall including earthing etc. complete as required.225 mm sweep

Supplying, installation, testing and commissioning of following sleek LED panel down lighters (luminaries) in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 36 watt, size 600 x 600mm

Supplying, installation, testing and commissioning of following LED fitting (luminaries) down lighters in round/ square shape complete shall be made up of die cast power coating housing complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 18/20 Watt

Supplying, installation, testing and commissioning of following LED fitting (luminaries) down lighters in round/ square shape complete shall be made up of die cast power coating housing complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt.. 9 Watt

Supplying, installation, testing and commissioning of following LED tube light fitting including batten with Electronic Driver Heat sink Capacitor complete with all other accessories on surface/ in false ceiling, including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 36 watt -4 feet

Supplying, installation, testing and commissioning of following LED tube light fitting including batten with Electronic Driver Heat sink Capacitor complete with all other accessories on surface/ in false ceiling, including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 18 watt -4 feet

Supplying, installation, testing and commissioning of following sizes fancy exhaust fan having built in lovers in existing opening in wall including earthing etc. complete as required 300 mm sweep

Supplying and fixing on surface/ recess prewired horizontal type 8 Way (4+24)double door, 415 volts TP&N, MCB distribution board of sheet steel phosphatized and powder painted complete with loose wire box, terminal blocks, 200 amps tinned copper busbar, common neutral link, earth bar, din bar, detachable gland plate, loose wire box, superior make terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks including interconnections, earthing etc. as required

1 No. 40A TPN MCB as Incomer;

6-32A SP MCB C series 10kA as out going feeder.

Earthing with G.I. earth pipe 3 mtr long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required.

Supplying and laying 25 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including soldering,excavation and refilling the trench etc. as required.

Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as required. 200 mm dia

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 3.5C X 95 sqmm

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 3.5C X25 sqmm

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 4C X16 sqmm

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 4C X10 sqmm

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 2C X10 sqmm

Supplying, fixing and cramping suitable size and all type aluminium ferule/ lugs to following size 1.1 KV grade power cable core/ lead, pressed with high pressure cramping tool including connection to switch gear/ MCCB etc as required. 4X16 sq.mm

Supply and making of end termination with brass compression gland and aluminum lugs for following sizes armoured aluminium conductor power cable of 1.1KV grade along with accessories, hardwares etc. required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3.5x95 sqmm

Supply and making of end termination with brass compression gland and aluminum lugs for following sizes armoured aluminium conductor power cable of 1.1KV grade along with accessories, hardwares etc. required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 4x25 sqmm

Supply and making of end termination with brass compression gland and aluminum lugs for following sizes armoured aluminium conductor power cable of 1.1KV grade along with accessories, hardwares etc. required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 4x16 sqmm

Supply and making of end termination with brass compression gland and aluminum lugs for following sizes armoured aluminium conductor power cable of 1.1KV grade along with accessories, hardwares etc. required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 4x 10 sqmm

Supply and making of end termination with brass compression gland and aluminum lugs for following sizes armoured aluminium conductor power cable of 1.1KV grade along with accessories, hardwares etc. required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 2C X10sqmm

Main Panel Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and depth above 300 mm and upto 450mm made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ameters ets as per specifications including powder coating painting with busbars, switchgears and other accessories etc complete as required as per direction of Engineer INCOMER 4 pole MCCB, 100A, Adjustable Microprocessor Release, 35KA -1 nos BUS-BAR 1 Set of 100A 4P Aluminium Bus Bar with colour coded PVC Sleeves OUTGOINGS 4 pole MCCB, 100A, Adjustable Microprocessor Release, 35KA - 2 nos 4P MCCB, 63A 35KA - 8 nos

Power panel for GF , FF Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and depth above 300 mm and upto 450mm made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ameters ets as per specifications including powder coating painting with busbars, switchgears and other accessories etc complete as required as per direction of Engineer INCOMER 4P MCCB, 63A 1 NOS as out going 35KA - 1 No BUS-BAR 1 Set of 100A 4P Aluminium Bus Bar with colour coded PVC Sleeves .Digital electronic MFM cum KWH meter must be BMS compitable & have modbus over RS 485 OUTGOINGS 6 Amps to 32 amps MCB TP ,440 volts- 15 no 6 to 32A SP MCB C series 10kA as out going feeder-15 no

Supplying and installing following size powder coated, perforated M.S. cable trays with perforation not more than 17.5% rigidly suspended from the ceiling with M.S. suspenders at a distance not more than 2.5 metre and near every junction/ joint etc complete as required 225 mm width X 50 mm depth X 1.6 mm thickness

Supplying and fixing of following sizes powder coated,perforated, M.S. cable trays bends (horizontal) turning at 900 in same plane with perforation not more than 17.5% rigidly jointed with cable tray etc. complete as required 225 mm width X 50 mm depth X 1.6 mm thick

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted/ welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Supply of hot dipped galvanized (in single dip to average 65 micron) octoganal pole made of 3mm thick steel sheet having window and flush cover with locking arrangement at suitable height from base for cable termination block, pole suitably reinforced with welded steel section at window cut section to make the strength of pole unaffected, with following minimum specifications including 3mm thick anchor plate, 4 nos 20mm dia foundation bolts of EN8 grade. (designed for wind speed upto 150km/hr) 7 metre high, dia 130mm at bottom and 70mm at top, base plate size 220x220x12mm, foundation bolts 700mm long

Designing and providing suitable RCC foundation in Cement Concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) for 3 mere to 12 metre high GI octagonal pole including steel reinforcement (minimum 90kg per cum), form work, embeding 2 nos 50mm dia PVC pipe for cable entry in each foundation, excavation disposal of surplus soil and curing etc. as required

Erection of GI octogonal/ tubular pole on existing cement concrete foundation having grouted bolts and nuts, aligning in true vertical position as required : 7 metre high

Supply and fixing following street light pole bracket on existing pole made out of 50 mm dia MS "B" class pipe welded to 300 mm long MS pole canopy of suitable dia at a angle of 102.50 including having MS triangular stiffner of size 150 X 50 X 5 mm thick, making arrangement for tightening the bracket with pole by providing suitable size heavy duty nuts and bolts in canopy, painting with one coat of approved steel primer etc. as required Single Over Hang 1.00 metre Long

Supplying, installation, testing and commissioning of following 230/250 volts LED street light fitting with gear box, igniter, with IP 65 protection on pole bracket complete . 60watt ( +/- 5 % W)

Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and depth above 300 mm and upto 450mm made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ameters ets as per specifications including powder coating painting with busbars, switchgears and other accessories etc complete as required as per direction of Engineer INCOMER 63A, 4P, 415V, MCCB, 36kA - 1No. CT's of ratio 63/5 Amps - 1 Set Multifunctional meter (Type M) - 1no BUS-BAR 1 Set of 100A 4P Aluminium Bus Bar with colour coded PVC Sleeves OUTGOINGS 32 amps MCB TP ,440 volts-10 nos 6 to 32A SP MCB C series - 10 nos 10kA as out going feeder

Providing and applying Water Proofing with two Component Product Fast flex /SikaTop®-107 Seal /AquaArm Top Guard in two coats with 10 years of waterproofing gaurentee from manufacturer, before first , Cleaning the surface of application thoroughly prepared by mechanical means, to remove all loose particles, laitance,etc Oil and grease, if any, Cleaning with water and brought to touch dry state. (Make MC Banchowe/Sunada/Fosrock/Dr.Fixit/Sika/BASF), All complete work should be execute as per manufacture specification & direction of Engineer-in-charge

Providing and Installation of Water cooler cum inbuilt UV Purification system : Weight - Max 55 Kg Dimension -530x680x1345 ± 5 mm, max 550x700x1350 mm (± 20 mm) Water Storage capacity : 40 Liters Water Cooling Capacity : 20 LPH Water purification Capacity Storage tank materials : Min 2 Liters per minute Dynamic monitor and control : SS-304 LCD Display, indicating temperature, bar graph for cartridge life, no-water Cooler and UV (ESS – Electrolytic Sanitizer System) Auto sanitizer

Providing and fixing of Thermoplastic Hose for Swinging Hose Reel, 20mm dia. and 30m long with Shut Off Nozzle(SS)

Providing and fixing standard short size gunmetal branch pipe with SS nozzle 16mm NB outlet with standard instantaneous type 63 mm dia coupling.

Supply, testing and commissioning of UL listed hooters

Supply, installation, testing and commissioning of Gong Bell Unit with tapping, pipes, Valves, interconnecting hoses and pipings complete as required to make it operational.

Supply, installation, testing & commissioning of Power Backup and other required accessories.

Supply, installation, testing & commissioning of Battery for Fire Panel other required accessories.

Supplying & fixing monoblock booster pump of capacity 450 Lt/min & against head of 35 m to get a pressure of 3.5 kg / sq.cm at the topmost hydrant with booster starter with M.S. frame and clamps as necessary for fixing the pumps on the top of slab as per site conditions and instructions of site engineer in charge.

Inbuilt of drain cover slab in providing perforated holes using PVC pipe 50 mm dia. including cost of allmaterials and labour involved with all leads and lifts etc. as per drawing and direction of Engineer in Charge.

Extra for providing and mixing water proofing Chemical in cement plaster work in proportion as recommended by manufacturer. (Liquid)

Supplying and fixing 32 mm dia, 30 mtr long Flax PVC hose pipe with 32 mm dia Male and Female PVC couplings duly binded with GI wire, rivets etc. as required.

Providing and laying in position of following UPVC Reducers suitable for 4, 6, 8 and 10Kg/Sqcm. Pressure pipes. [Conform to IS 4985:2000 and IS7634(PT-3) :2003, IS 7834 (PT-I to VIII: 1987] 50 x 32

Providing and laying in position of following UPVC Reducers suitable for 4, 6, 8 and 10Kg/Sqcm. Pressure pipes. [Conform to IS 4985:2000 and IS7634(PT-3) :2003, IS 7834 (PT-I to VIII: 1987] 80x 50

Supplying and laying double wall HDPE pipe having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm including excavation, dismantling of road if required and refilling the trench etc. as required.40 mm Dia