SPECIAL REPAIRS TO CERTAIN BUILDINGS, ROLLING SHUTTERS AND SWT AT BENGDUBI MIL STN UNDER GE BENGDUBI

Amount

Dimantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings including ridges, valley gutter etc, complete all as specified and as directed.

S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering, cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S&F pre-painted colored plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer,as in roof covering, cladding to wall, ridge, valley gutter, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

Dismantling wrought iron or mild steel work as in rafters, purlins, truss etc or of any description not otherwise provided for, complete all as specified and as directed.

S&F mild steel rolled sections [Fe 410-W (Gde E-250) quality - B] as in roof trusses (framed), trussed, main and cross beams, hip and jack rafters, purlins, Gusset plate and base plates, where connected to common rafters and running rails, distance pieces, cleats, guides for sliding doors; fixed with angle cleats or other connecting plates, framing for cladding, staging for water tanks, nuts, bolts, washers etc,includng welding or riveting etc, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

M&L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square / rectangular) of approved size, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

All as per item No 8 above but for vertical surfaces such as skirting etc, over and including 10mm thick back coat in CM 1:4.

M&L for coloured Glazed ceramic tiles of size 300mmx 450mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM 1:4, complete all as specified and and as directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site outside the premises, complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:4) on brick work or concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacturer instructions, complete all as specified and as directed. Note:- WPC shall be measured and paid seperately.

M&L for rendering 15 mm thick in CM (1:6) on the surfaces of brick work or concrete, finsihed even and smooth (without using extra cement), complete all as specified and as directed.

M&L for rendering 10mm thick in CM 1:3 on concrete surfaces of ceiling/Chajja/Facia of chajja etc, finished even and smooth without using extra cement, complete all as specified and as directed.

Supply only liquid water proofing compound, complete all as specified and as directed.

M&L for preparation of old/new surfaces of wall/ceiling and applying one coat (minimum 1mm thick) of Birla/Asian wall care putty, complete all as specified and as directed.

M&L for preparing new surfaces of walls duly applied with wall care Putty and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed. Note :- Provision of wall care putty not included in this item.

M&L for preparing new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and as directed.

M&L for preparing newely plastered surfaces of wall and applying two coats of cement base paint, complete all as specified and as directed

M&L for Writing Letters or Figures (Block, Roman, Italic or Indian) n.exc 30 cm height with thick paint so that they stand out boldly and solidly without showing signs of brush marks, also including repainting until desired result is obtained, complete all as specified and as directed. Note :- Letters under 2 cm height shall be measured as 2cm.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc, also including taking down of grills/ guard bars (where exists) and disposing off the retrieved debris outsite the premises, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc, also including taking down of grills/ guard bars (where exists) and disposing off the debris outsite the premises, complete all as specified and as directed.

Taking down of Aluminium joinery (including chowkat, fittings etc), including taking down of grills/guard bars (where occurs) & cutting holes for removing the hold fasts etc, also including disposing off the debris outside the premises, complete all as specified and as directed.

S&F Factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for doors with one or more rebates includings necessary provision of fixing lugs, locks strike plate etc, also including application of one shop coat of Zinc Chromate primer, complete all as specified and as directed. Note:- Hinges shall be paid for seperately.

S&F Factory made 1.25 mm thick pressed steel frame of size 165 X 60 mm for doors with one or more rebates includings necessary provision of lugs, locks strike plate etc, also including application of one shop coat of Zinc Chromate primer, complete all as specified and as directed. Note :- Hinges shall be paid for separately.

S&F Factory made Solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. Square tube, complete all as specified and shown on drawing for SI No. 08095 on Srl Page No. 180 of SSR (Part-II) and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails.MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail and bottom rail, on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as shown on drawing for SI No 8080 on Srl Page No 176 of SSR Part-II, complete all as specified and as directed.

S&F Factory made 30mm thick flush shutter solid core construction with block board core and ply wood face panels, commercial type on both sides including provision of 4mm thick 2nd class hard wood edging to the exposed edges of the shutter, complete all as specified and as directed.

M&L for 2" class hard wood (Hollock/Kalasiris/Brijsal/Gamari) (klin seasoned and chemically pressure treated) 30 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc, edges of framing plain, chamfered or round, fitted with cut and mitred beads for securing glass, etc, size of members of shutters as specified in SSR Part-1, Section 8, clauses 8.24(a), complete all as specified and as directed

Taking down of steel windows & vents (including taking down of grills/framed guard bars, where occurs); including cutting holes for removing of the lugs etc, also including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

S & F factory made steel windows with side hung shutters including projecting type hinges with steel handle, and peg stay, complete with glazing bars, dovetaild or welded, including application of one shop coat of Zinc Chromate primer, complete all as specified and directed.

All as per item No 31 above but steel window without glazing bars.

S&F Factory made, steel ventilator with top hung shutter including hinges, steel peg stay, including application of one shop coat of Zinc Chromate primer, complete all as specified and directed.

M&L for the Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed.

S&F 4.00mm thick sheet glass of ordinary quality as in glazing for Aluminium Joinery or for steel surrounds with & including oil putty or glazing for wooden surrounds with & including putty and wooden beads (cost of wooden beads deemed to be included in the relevant item of joinery), complete all as specified and as directed.

S&F 3mm thick Figured glass, pin head type and glazing for Aluminium Joinery or with & including oil putty for steel surrounds, in squares, complete all as specified and as directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with and including stainles steel wire staples etc, complete all as specified and as directed.

S&F standard aluminium powder coated section(minimum thickness of powder coating shall be 50micron and colour shall be as approved by the GE) as in frame, shutters for doors, windows / ventilators, Fixed/ Openable / side hung/ sliding two or three track or in any pattern, partitions etc, cut to size, jointed with cadmium plated steel screws, including Aluminium beading & rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc, complete all as specified and directed. Notes:- (i) Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. (ii) The accessories (including Aluminium mongries etc) required to be provided for windows, vents and doors as per directions of Engineer-in-charge shall be provided but weight for the same shall not be considered. (iii) Cost of all the items, accessories & Aluminium mongries required for the entire completion of the work shall be deemed to be included in the quoted rate. However glass panes, wire cloth shall be measured and paid separately under respective items.

S&F 5mm thick sheet glass of ordinary quality as in glazing for Aluminium Joinery with & including oil putty, complete all as specified and as directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with and including galvanised wire staples etc, complete all as specified and as directed.

M&L preparing of old painted surfaces of wood & wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed

M&L preparing of old painted surfaces of wood & wood based surfaces of any description, not otherwise described, not exc 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed

M&L preparation of old painted surfaces of steel & iron work of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

M&L preparation of old painted surfaces of steel & iron work of any description, not otherwise described, not exc 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

M&L preparing new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

M&L preparing new wooden surfaces of any description, not otherwise described, not exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

M&L for Preparation of steel and iron surfaces duly applied with shop coat of primer of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint, complete all as specified and as directed. Note : Cost of application of shop coat of primer not included in the above item.

M&L for Preparation of new steel and iron surfaces of any description, not exc 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

M&L for preparing the old decorated surfaces of walls and applying one coat of white wash, complete all as specified and as directed.

M&L preparing old plastered surfaces of ceiling and applying one coat of white wash, complete all as specified and as directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

S&F 300mm long, mild steel, sliding door bolt, stove enamelled black, bolt type, with bright bolt not less than 12mm dia, with & including a minimum of 6 bolts & nuts, complete all as specified and as directed.

S&F 150mm long, Aluminium anodised barrel tower bolt of extruded section, complete all as specified and as directed.

S&F 150mm long, mild steel barrel tower bolts, stove enamelled black, with bright bolt complete all as specified and as directed.

S&F 150 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F 150mm size mild steel, pressed handle, oval type, stove enamelled black, complete all as specified and as directed.

S&F 100mm size butt hinges, heavy weight, cold rolled, mild steel, complete all as specified and as directed.

S & F 75mm size butt hinges,heavy weight, cold rolled, mild steel, complete all as specified and as directed.

Taking down 15mm bore steel tubing & connections, complete all as specified and as directed.

All as per item No 60 above but 20 mm bore

All as per item No 60 above but 25 mm bore

Supplying and laying of 16mm outer diameter CPVC pipes SDR 11 (including in short lengths) with and including SDR 11 fittings, partly on the surfaces and partly concealed in the walls & ceiling or laying in floors, also including cutting chases of the required size and making good the same after fixing of the pipes in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per item no 63 above but 20 mm outer diameter pipes.

All as per item no 63 above but 25 mm outer diameter pipes, entire quantity to be fixed on the surfaces of wall, ceiling, floor etc (cutting, chasing not required).

Dismantling water tanks exc 250 litres but not exc 500 litres capacity including disconnecting the connections, complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank 500 Litres capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position, complete all as specified and as directed.

S&F in repairs, Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 25 mm bore, complete all as specified and as directed.

S&F in repair ball brass valve, high pressure, with ploythene float and flynut complete, screwed for iron pipe or brass ferrule 20 mm bore, complete all as specified and as directed.

S&F in repairs bib tap, long Body with Wall Flange, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and as directed. (Make : ESSCO : Cat No. SQT-512KN or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F in repairs tubular towel rail, 20mm dia, D type, brass chrormium plated, 600mm long between flanges, complete all as specified and as directed. (Towel Rail shall be of make- Prayag : Cat No. BA-01 or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S & F in repair Grating doom 125 mm dia with waste hole of PTMT ( Minimum weight 40gms), complete all as specified and as directed .

S&F in repairs angle valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed. (Stop valve shall of make ESSCO : Cat No. SQT-526KN or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S & F in repair cast copper alloy, chromium plated, wall mixer, Non-telephonic shower system with Aerator (Make : ESSCO : Cat No : SQT-520KN or equivalent of other make as mentioned in Appx 'B' of Particular Specification as approved by the GE) for mixing hot & cold water, screwed down for 15mm bore iron pipe, complete all as specified and as directed.

S&F in repairs PVC valveless, double syphonic action type, flushing cistern, low level of 10 Litres capacity, white, with and including inlet, ball valve, float, 32mm dia flush pipe of polyethylane of low or high density or PVC, flushing bend & handles, also including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet & making connections, complete all as specified and as directed.

S&F in repair Wall Hung, vitreous china wash basin (Make JAQUAR : Cat No. SLS-WHT-6801 or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE), 1st quality, white, flat back, approx size 575x465x195 mm, excluding taps but including 32 mm bore brass chromium plated waste fittings, 32mm bore PVC waste pipe, MS brackets, complete all as specified and as directed.

S&F in repairs 15mm size PVC connection of 450 mm length including brass nuts, complete all as specified and as directed.

S&F in repairs, vitreous china, 1st quality, bowl urinal, flat back, approx size 355x340x535mm, white (excluding flushing cistern, flush pipe) but with & including gratings, union for discharge pipe, also including provision of PVC waste pipe and all the fixing accessories, complete all as specified and directed. (The urinal shall be of make- JAQUAR : Cat No. URS-WHT-13261 or equivalent of other makes as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F in repair cast copper alloy, chromium plated, urinal spreader, complete all as specified and as directed.

S&F in repairs, vitreous china, 1st quality, squatting pan, Orrisa pattern of approx size 260 x 440 x 580mm, white with integral foot rests, 'P' trap including making connection to trap, flush pipe, anti-syphonage pipe etc, the WC Pan shall of make JAQUAR : Cat No. CNS-WHT-OP01 or equivalent Cat No. of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE, complete all as specified and as directed.

S&F in repairs Vitreous China Wash Down Water closet (Pedestal Pattern) 1st quality, approx size 350x475x390mm, white (excluding flushing cistern & flush pipe) including plastic water closet seat white, closed pattern with flat bottom and cover and mild steel CP or aluminised huiging device, making connections, the EWC Pan shall of make JAQUAR : Cat No. CNS-WHT-553SN or equivalent Cat No. of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE, complete all as specified and as directed.

S&F in repairs for 100 mm bore out let cast iron floor trap with and including grating, also including jointing to waste pipe and provision of cement concrete type B-1 (1:2:4) block of required size for fixing, complete all as specified and as directed.

S&F in repairs 100mm bore cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and as directed.

S&F in repair cast iron cowl for 100 mm bore C.I. pipe, complete all as specified and as directed.

S & F in repairs 110 mm bore uPVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc, laid in floors/ trenches etc, complete all as specified and directed. Note :- (i) Quoted rates shall also be deemed to include for cutting of the holes (in the wall etc) where required/ directed and making good the same in CM 1:3 to match with the existing surfaces. (ii) Excavation & Earth work shall be measured & paid for separately.

S & F in repairs 75 mm bore uPVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc, laid in floors/ trenches etc, complete all as specified and directed. Note :- (i) Quoted rates shall also be deemed to include for cutting of the holes (in the wall etc) where required/ directed and making good the same in CM 1:3 to match with the existing surfaces. (ii) Excavation & Earth work shall be measured & paid for separately.

S&F in repairs 110mm bore uPVC (SWR), junction single (Single T), equal or unequal with and including rubber ring joints, complete all as specified and directed

S&F 110mm bore uPVC (SWR) bends (any radius), with and including rubber ring joints, complete all as specified and directed.

S&F 75mm bore uPVC (SWR) bends (any radius), with and including rubber ring joints, complete all as specified and directed.

S&F in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with and including solvent cement, also including provision of cement conconrete type B-1 (1:2:4) block of required size for fixing, complete all as specified and as directed.

Excavating in trenches n.exc. 1.50m wide and n.exc 1.50m in depth for foundation, laying of cable, pipe etc and n.exc 10Sqm on plan & not exc 1.5m in depth for manhole etc and getting out in soft/loose soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified and directed

Removing excavated material to a distance not exc 50.00 mtr and depositng where directed at a level n.exc 1.5m above the stating point, complete all as specified and as directed.

Demolition and breaking up 150mm bore SGSW drain pipes, set in cement mortar, complete all as specified and directed. Note:- Excavation and Earth Work shall be measured and paid for separately.

M&L for cement concrete 1:3:6 type C-2 using 40mm graded stone aggregates for 150 mm bore pipes as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, complete all as specified and as directed.

M&L for 150 mm bore SGSW pipe, grade 'A', laid in trenches including jointing with cement mortar, complete all as specified and directed. Note:- Excavation & Earth Work, PCC bed & haunching shall be measured & paid for separately.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level), Complete all as specified and directed.

Demolition of cement concrete (un-reinforced) as in sunken floors etc and of any description & in any position, not otherwise specifically provided for, including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for 75mm thick cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregates) as in sub base of flooring, complete all as specified and as directed.

M&L for factory fabricated Hydraulically machine pressed cement concrete chequered tiles of size 300x300X25mm thick (with grey cement and pigment), set in neat cement slurry including provision of 15mm thick cement screed bedding layer in CM 1:4, tiles joints shall be grouted and immediately after grouting, the joints shall be pointed flush in separate process in CM 1:3 mixed with pigments to match the colour of the Tiles, complete all as specified and directed.

M&L for 60mm thick Factory Fabricated Machine pressed precast concrete reinforced with glass fibre interlocking paver blocks confirming to IS 15658-2006, M-35 Grade, glossy finished, vibro compacted (size, shape and colour as approved by the GE) with grey cement and pigments over & including 25mm thick layer of sand cushioning, complete all as specified and as directed.

M&L for providing 75mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of 3:1, complete all as specified and directed.

M&L for 14 to 15 mm thick machine cut, pre-polished, black jet, premium quality, granite stone slab, as in basin plateform (incl oval shape cutting for fixing of basin), cills, jambs etc, laid over and including 15mm thick CM 1:4 screed bed, jointed with grey cement slurry and pointed with white cement mixed with admixture of pigments to match with the shade of granite stone including rounding / moulding the edges half round, complete all as specified and directed.

M&L for 40mm thick cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregates) as in floors, finished even & smooth, without using extra cement, complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/ blankets, any thickness, including cover fillets, and existing frame work also, complete all as specified and as directed.

S & F 4mm thick Non-asbestos fibre cement decorative/designer building boards (4mm thick pre-painted designed decorative type E-Board) to steel frame work with screws in ceiling (flat and/or slopping) and including jointless finish with & also including joining compound and tape as per manufacturer instructions, complete all as specified and as directed. Notes :- (i) The board shall be confirming to IS-14862 and shall be manufactured from the homogeneious mixture of cement, quartz and cellulose and shall be curred with high pressure steam using auto claving process. (ii) Steel frame work shall be measured and paid for separately.

S&F of GI frame work (size of grid 600mm x 600mm) for seamless ceiling comprising GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, including provision of Hangers of 4mm dia G.I wire (length as required at site), complete all as specified and as directed.

M&L for preparation of new surfaces of Non-asbestos fibre cement boards as in ceiling and applying two coat of oil bound distemper over a coat of primer , complete all as specified and as directed.

S & F PVC false ceiling consisting of 600x600, 5mm (±0.25mm) thick plain embossed PVC sheet of 600kg/cbm Density manufactured by an ISO-9001-2008 certified company, used as panel insert in & including a frame work made using anodised aluminium T-Section of size 1"x1"(25X25mm, 19 guage or 1mm thick) in square pattern of grid sizes 2'X2'(600x600), the aluminium frame work shall be supported from the ceiling with & including provision of 'J' Hook and G.I wire/6mm M.S rods of required sizes to maintain proper level etc, the aluminium framework shall be supported on side wall with & inclusing provision of aluminium L- section size 1"x1" (25x25mm) angles etc. complete as per manufacturer's instructions all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description as in SWT walls, kitchen shelves, cooking platform, lintels, chajja, beams, slabs etc and in any other position, not otherwise specifically provided for including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Use and waste of formwork to Beams, cantillevers, bressumers, lintels, shelves and similer items for rough finished flat surface of concrete, complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizonal or slopping) for rough finished flat surfaces of concrete, complete all as specified and as directed.

Use and waste formwork to chullah hoods, chajjas, troughs and similer items including edges for rough finished flat surface of concrete, complete all as specified and as directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished flat concrete surfaces, complete all as specified and as directed.

Use and waste of formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc; vertical or to batter, rough finished flat surfaces of concrete, complete all as specified and as directed.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc, complete all as specified and as directed.

M&L TMT bars 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc. complete all as specified and as directed.

M&L TMT bars 8mm dia and over upto and including 10mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc, complete all as specified and as directed.

M&L for reinforced cement concrete M-30 (Design Mix) type A-1 (using 20 mm graded stone aggrgates) as in in walls, retaining walls, basement walls, ballast walls and the like, any thickness, above top of footing, including attached pilasters, buttresses, complete all as specified and directed. Note: Reinforcement and Form Work shall be measured and paid for seperately.

M&L for rendering 20mm thick in CM 1:4 in two layers (each layer consisting of 10mm thick, to be laid separately) bottom layer finished even & fair, top layer finished even & smooth without using extra cement, in top layer only W.P.C to be mixed as per manufacturer's instructions) on the brick/concrete wall surfaces etc, complete all as specified and directed. Note: W.P.C shall be measured and paid for seperately.

Demolition of brick work or rubbled stone masonry including all quoins, arches , pillars etc built in cement mortar including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for preparing new plastered surfaces of wall and applying three coats of white wash, complete all as specified and as directed.

M&L for Brickwork with fly ash Bricks, old size of class designation 75 (i.e of average compressive strength 75 Kgf/Cm2) straight or curved on plan exc 6m mean radius, built in Cement morter 1:6, complete all as specified and directed

M&L for Brickwork with sub class 'B', old size bricks of designation 75 (i.e of average compressive strength 75 Kgf/Cm2), straight or curved on plan exc 6m mean radius, built in Cement Morter 1:4, complete all as specified and directed.

M&L for brick work with fly ash Bricks, old size of class designation 75 (i.e of average compressive strength 75 Kgf/Cm2), straight or curved on plan to any radius, built in CM 1:4, as in half brick thick walls, complete all as specified and as directed.

M&L for rendering 10mm thick in CM 1:4 on the surfaces of brick work or concrete, finsihed even and smooth (without using extra cement), complete all as specified and as directed.

Demolition of cement concrete (un-reinforced ) as in roof covering, levelling course over roof, roof kerbs, benching & the fillets including taking down existing un-servicable waterproofing treatment from roof slab surfaces (also including roughening of old concrete surfaces by picking), cleaning the surfaces by wire brush and also including disposing off the retrieved debris outside the premises / site, complete all as specified and as directed.

M&L for 25 mm thick (average thickness), PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregates) mixed with water proofing compound as per the manufacturer's instructions as in roof covering/ levelling course, finished even & smooth without using extra cement, complete all as specified and directed. Note : - W.P.C shall be measured & paid separately.

M & L for APP modified roof treatment over existing roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications, complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying 3mm thick APP modified water proofing polymeric membrane reinforced with non woven polyester fibre using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.00 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm. (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption,% - Not more than 0.15. (ix) Cold flexibility - (-) 50C. (x) Dimentional stability % change = Maximum 1%. (xi) Heat Resistance - Does not dirp at 1200 C Note : The quoted rate shall also be deemed to include for cutting grooves of size and shape as required in the parapet wall for tackling the APP membrane in the wall including making good the surfaces of groove as well as damaged surfaces of the wall after tackling of membrane in CM 1:3 to match with the adjoining surfaces.

M&L for applying one coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm over APP membrane, complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation concrete and mass filling, complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregates) as in copings, roof kerbs, staging of water tank, for sealing of chases for fixing of pipes upto DB etc, including necessary formwork, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregates) as in hold-fast blocks, blocks for fixing lugs, filling of pressed steel chowkhat and the like including necessary form work, complete all as specified and as directed.

Dismantling existing steel rolling shutters including top cover, guide channels, components / fittings etc, complete all as specified and as directed.

S & F Factory made, 1.25 mm thick (thickness of latths) steel rolling shutters, gear operated type with bevel gear box and crank handle, guide channels, as specified including top cover, anchoring rod hasp & staple; applying one shop coat of primer, erected in position as indicated, complete all as specified and as directed. Note : Payment for lever locks & ball bearing shall be measured and paid for separately.

S&F Safety lever locks mild steel with 4 levers for rolling shutters, complete all as specified and as directed.

S&F Ball bearing for rolling shutters, complete all as specified and as directed.

S&F mild steel work conforming to Fe-290 Gde-E-165 as in hold fasts; wall ties; hooks for hanging fans and similar small articles, complete all as specified and as directed.

M & L for preparing old treated surfaces of wall and applying one coat of oil bound distemper, white or any tint as approved, complete all as specified and directed.

M&L for preparing Old plastered surfaces of wall and applying one coat of cement base paint, complete all as specified and as directed.

M&L for post anti-termite treatment at points of contact of wood work by chemical emuision (in oil or kerosene based solution ) @ 0.50 litre/hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same, complete all as specified and as directed.

Hacking out old broken glass any thickness, size, quality and description from metal frames including punching or drilling out old glazing pins /springs clips, complete all as specified and directed.

S&F in repairs stop valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed (The stop valve shall be of make : ESSCO : Cat No. SQT-513KN/SQT-513BKN or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications as approved by the GE).

S&F in repairs Pillar taps with Arrestor , fancy type, cast copper alloy, with long swan neck , chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, Make : ESSCO : Cat No. SQT-508KN or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications, or approved by the GE, complete all as specified and as directed.

Taking down carefully existing aluminium/copper point wiring (light / fan / socket or power point) complete, with all fittings such as switch socket combination, switches, sockets, regulator, ceiling rose, utility light fittings and lamp holders etc and making good the disturbed surfaces of walls, roof and floor etc to match with the existing specification, complete all as specified and as directed.

Taking down existing unserviceable distribution board, switch fuse unit, enclosure for MCB / DB (inclusive of MCBs etc of any type and capacity) and making good the disturbed surfaces all as specified and as directed.

Taking down existing unserviceable submain wiring (including conduit /casing -caping), any size and making good the disturbed surfaces to match with the adjoining surfaces, complete all as specified and as directed.

Material and labour for point wiring for one light and/or one fan point controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia, (also including conduit fittings & PVC Junction boxes etc, along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made pressed steel sunken boxes (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm), concealed type with and including 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc, testing on completion also including cutting chases for concealed conduit, steel boxes etc, pinning in, making good the surfaces in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per Item No 149 above but for one switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per item No 149 here-in-before but for one socket with other switches on the same board, complete all as specified and as directed.

All as per item No 149 here-in-before but for one15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, complete all as specified and as directed.

All as per Item No 149 here-in-before but for one AC/Geyser, independent with 4.00 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 4.00 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, complete all as specified and as directed.

Supply and fixing switch piano flush type, single pole, one way, 6 amps, complete all as specified and as directed.

Supply and fixing switch socket combination, 2 in 1, 5 Pin, 6 Amp, flush type, complete all as specified and as directed.

Supply and fixing switch socket combination, 2 in 1, 3 pin, 5 and 15 amp, flush type, universal, complete all as specified and as directed.

Supply and fixing ceiling rose, 3 phase /PVC/Polycarbonate, isolated body, complete all as specified and as directed.

Supply and fix electronic fan regulator, flush type, 5 step not less than 100 watt, complete all as specified and directed.

Supply and fix LED tube light fitting 1 X 20 Watts (4 Ft) 240 Volts, Ultra bright polycarbonate LED Tubelight with very high efficiency suited for installation in & including T8 tubelight with G13 lamp holders, complete with and including all accessories, internally pre-wired and including making connection by providing 3 core 1.5 Sqmm PVC insulated stranded copper conductor cable, complete all as specified and directed. Make and Cat No of T-8 Tubelight : HAVELLs Cat No PHOTONULTRAE2.01213T8SSTL20WLED865SPC or equivalent of make Crompton/PHILIPS/BAJAJ as approved by the GE. Make and Cat No of T8 Tube Light Fittings : HAVELLs Cat No Regal Batten T8UPTO1X22WSSBSWH or equivalent of make Crompton/PHILIPS/BAJAJ as approved by the GE.

S&F in repairs Building Security light, presure die-cast housing with individual LEDs as light source and Lens embedded PC cover having TOP opening, separate driver compartment with IP 66 protection and impact resistance of IK-07, make BAJAJ : Cat No. BRLEP15WLED or equivalent of make HAVELLS/PHILIPS/CROMPTON as approved by the GE and provision of copper conducor cable for connection, complete all as specified and directed.

Supply and Fix Lamp holder, PVC/Polycarbonate type with back plate, complete all as specified and directed.

Taking down existing exhaust fan of size 380 mm sweep after disconnecting the electrical connection, rewinding the fan motor with & including provision of new super enameled copper wire, replacement of unserviceable spares/parts i.e capacitor, bearing etc, lubricating with approved grade of grease, painting the steel body with 1 coat of synthetic enamel paint, refixing the same fan including making all electrical connections, complete all as specified and directed.

S&F sturdy Engineering plastic body exhaust fan, copper winding of 250mm sweep, 230 volts, 50Hz, RPM 1200, AC, single phase, complete with & including accessories, louver shutters, provision of PVC copper conductor cable for making connection from existing ceiling rose, making opening for fixing of the exhaust fan & making good the surfaces of the opening with CM 1:3 to match with the existing surfaces, complete all as specified and directed. Make : USHA Model No CRISP AIR LX EXHAUST FAN or equivalent model of make CG/HAVELLS/BAJAJ/ORIENT as approved by GE.

Supply and fixing sheet metal enclosure for MCBs DBs, Double Doors, phosphatised, Powder coated , single pole and neutral (SPN), 240 Volt , 8 Ways with and including common bus bar at incoming end, also cutting nitches/opening in the wall for accommodating the enclosures, plastering to the back & sides of nitches/surfaces of opening in CM 1:3 & making good the damaged surfaces to match with the adjoining surfaces, complete all as specified and directed.

Supply and fixing sheet metal enclosure for MCBs DBs, Double Doors, phosphatised, Powder coated , triple pole and neutral (TPN), 415 Volt , 4 Ways with and including common bus bar at incoming end, also cutting nitches/opening in the wall for accommodating the enclosures, plastering to the back & sides of nitches/surfaces of opening in CM 1:3 & making good the damaged surfaces to match with the adjoining surfaces, complete all as specified and directed.

Supply and fixing MCB, SPN, C series, 10kA ruputring capacity, 20 to 32 Amps, 240 Volts, complete all as specified and as directed.

S & F MCB, 'C' Series, Single Pole, 240 volts, 6 to 32 Amps, ruputring breaking capacity 10KA, complete all as specified and directed.

S&F MCB, 'C' Series, Four Pole, 63 Amp, 415 Volts, reputring capacity 10 KA, complete all as specified and directed.

S&F street light bracket made out of 32 mm bore GI Light grade pipe 1.00 M long bent to the shape as required for steet light fittings pronded with two pairs of MS Flat Iron 50mm x 6mm clamps of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flat iron surfaces with two coats of synthetic enamel paint over a coat of red oxide primer complete including taking down of unserviceable one, complete all as specified and directed.

Material and labour for galvanized iron tubing 50mm bore light grade with all fittings for protection of cable, laid in trenches/ along poles /wall/floor incl necessary clamps, bolts/nuts, complete all as specified and as directed. Note:- Excavation and earth work shall be measured and paid separately.

Materials and labour for earthing complete with galvanised earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25 metre below normal ground level with top edge of the plate not less than 1.50 metre below normal ground level connected to galvanised lead lead wire 4.0 mm dia by means of bolts, nuts and washers and check nuts of galvanised iron or steel GI earth wire protected by 15mm bore light grade galvanised iron pipe including of 20 mm dia medium grade GI water tubing sheet metal 4mm wire mash funnel, charcoal or coke and common salt in paint and testing on completion as shown on electrical plate No.5 ofm SSR Part-I. including taking out unserviceable one, complete all as specified and directed.

Supplying, laying, jointing and testing XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (Heavy duty) with stranded aluminium conductor 1100 volts grade, cross sectional area 16 Sqmm 4 core, in trenches /along poles/on wall etc, complete all as specified and as directed Note For item No 172 : Excavation and earth work, sand cushioning, protection covers shall be measured and paid for separately.

Supplying, laying, jointing and testing XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (Heavy duty) with stranded aluminium conductor 1100 volts grade, cross sectional area 10 Sqmm 2 core, in trenches /along poles/on wall etc, complete all as specified and as directed Note For item No 173 : Excavation and earth work, sand cushioning, protection covers shall be measured and paid for separately.

Taking down unserviceable underground cable of any size from the trenches, along floors, walls, pole etc, complete all as specified and directed (Note:- Excavation & Earth work shall be measured & paid for separately)

Material and labour for sand cushioning for protection of underground cable consolidated and compacted with clean dry sand all as specified and as directed (Compacted thickness shall only be measured and paid)

Material and labour for well burnt Sub class 'B', old size bricks, best quality locally available laid flat, dry in trenches for cable protection, complete all as specified and as directed.

Material and labour for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size 2.50 sqmm and one single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size 2.50 sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 20 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, complete all as specified and as directed. Note for Item No 177 to 179 :- For payment purposes, 2 runs of main cable (each of 1RM), 1 run of earth continuity cable (1RM) and one run of conduit (1RM), all together shall be considered as "1RM".

Material and labour for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size 4.00 sqmm and one single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size 4.00 sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 25 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, complete all as specified and as directed.

M & L for sub main wiring with 2 run of single core FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm alongwith one run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm as earth continuity conductor drawn through and including PVC concealed conduit, medium grade, 25mm bore complete with fittings, PVC Junction Boxes, fixing accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, complete all as specified and directed.

Supply and fixing indoor LED 18/20 watt luminaires (4 Feet Lamp) comprises of extruded channel in thermally conductive material, high translucent serrated milky white diffuser, make Crompton : Cat No LDL-20-CDL or equivalent of make BAJAJ/PHILIPS/HAVELL's as approved by the GE, including provision of twin twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

Supply and fixing indoor LED 9/10 watt luminaires (2 Feet LED Lamp) comprises of extruded channel in thermally conductive material, high translucent serrated milky white diffuser, make Crompton : Cat No LDL-10-CDL or equivalent of make BAJAJ/PHILIPS/HAVELL'S as approved by the GE, including provision of twin twisted copper conductor flexible wire from ceiling rose to connector, complete all as specified and as directed.

Supply and fixing sheet metal enclosure for MCCBs DBs, Double Door, phosphatised, Powder coated , Triple Pole and Neutral (TPN), VERTICLE TYPE , 4 way, 415 Volts, complete with and including 200 Amps rated bus bar, also cutting nitches/opening in the wall for accommodating the DB's, plastering to the back & sides of nitches/surfaces of opening in CM 1:3 & making good the damaged surfaces to match with the adjoining surfaces, complete all as specified and as directed .

S & F Adjustable Type, MCCB 63 Amps, 25KA, 4 Pole, 415 Volts, complete all as specified and directed.

M&L for earthing complete of advance encapsulated compound based (CPRI tested) maintenance free, pipe-in-pipe technology upgraded (Zinc & Alloy coated). Zinc coated (80-100) microns with pure zinc(99.9%) & alloy coating (200-250) microns. Earthing system shall be conforming to IS-3034, the outer and inner pipe shall be 76.2mm & 41.9mm dia, 3 metre length Zinc coated with additional special alloy coating 300mm on the topside for additional protection of the terminal, annular space between the pipes being filled up with compact fill (CF) (Crystalline conductive compound). The compact fill (CF) mixture shall be machine pressed in the pipes and should not disintegrate or collapse when outer pipe corrodes. The inner pipe shall be extended with terminals for connectivity. The job includes digging the pits of 300mm diameter and refilling the same with 4 bags (25 Kgs/bag) electrodite/ conductolite back fill comopound (Ground Enhancer). The BFC shall be eco friendly, it shall not contain environmentally hazard materials having ROHS certification from NABL accredited lab. The earth pit shall also be provided with earth pit cover for protection and safe guard of terminals. The earth electrode (the main component of the earthing system) which is in direct contact with the ground shall be able to provide a means of releasing or collecting earth leakage current. The materials shall have good electrical conductivity & anti-corrosion property in wide rage of soil condition and testing on completion including replacing the existing soil with black soil for 80cm dia (Black soil shall be filled for total 80cm dia - 30cm dia of earth pit) (for the total depth of pit) around the 300mm dia pit, Make : ASHLOK Model –ASEEL-39 ZC & AC (zinc & Alloy) or equivalent as approved by the GE and also including taking out/ dismantling of the existing earthing, complete all as specified and as directed. Note : Earth results obtained should be minimum 01 Ohm.

Boring/Drilling (horizontally) using ultrasound technique and necessary machine for passing pipe for protection of the cable at approx 1 metre depth in soil below existing road, pavement, hardstanding etc without damaging to the existing surfaces, getting out & disposal of spoil to a distance not exceeding 50 metre from the site of the work, complete all as specified and directed. Note :- Cost of pipes & cable not included in the scope of above item.

S&F in repairs Building Security light, presure die-cast housing with individual LEDs as light source and Lens embedded PC cover having TOP opening, separate driver compartment with IP 66 protection and impact resistance of IK-07, make BAJAJ : Cat No. BRLEP20WLED or equivalent of make HAVELLS/PHILIPS/CROMPTON as approved by the GE and provision of copper conducor cable for connection, complete all as specified and directed.

Supply and Fix LED 36 Watt, 600x600mm Square recessed full lit Luminaire with glare free uniform illumination (more than 100 lumen/Watt) including provision of copper conductor cable for connection, complete all as specified and as directed. Make - Crompton Cat No : LCTLRNE-36-FO-WW or equivalent of make BAJAJ/PHILIPS/HAVELL'S as approved by the GE.

Supply and fixing in repairs, single pole and neutral enclosure, with & including a two pin and earth plug and socket, also with and including one number double pole, MCB, 20 Amps, 240 volts, 10 KA ruputring capacity, complete all as directed and specified.

M/S G D CONSTRUCTION

M/s KASHMIRA SINGH BARMI AND SONS

HARBHAJDAS AGARWAL

M/S.TIRUPATI CONSTRUCTION

M/S R. K. INDUSTRIES

M/S JYOTI SHARMA AND SONS

CHAKRABORTY AND SONS

S.N. GHOSH AND CO.

Prahalad Rai

M/S JANATA CONSTRUCTION