Improvements to elkhill toilet in Udhagamandalam Municipality

Improvements to Elkhill toilet in Udhagamandalam Municipality

Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Plain Cement concrete 1 : 2 : 4 (one cement, two sand and four aggregates) using 20mm ISS HBG metal including cost and conveyance of all materials and labour charges for mixing, laying, compacting and curing etc, complete as per SS

Painting external wall with two coats of best approved quality of Plastice Emultion Paint over a including One Coat of priming of Exterior Emulsion Paint - Water Based Primer (Liquid) primier over cement surface wall as dirceted by the departmental officers including cleaning preparing the surface etc,complete complying with standard specification.The cement paint should be got approved by the departmental officers before use on work

Paving the floor with design antiskid ceramic tiles (colour and shade as directed) of size 305mm x 305 mm x 6mm in all floor aver a base layer of cement mortar 1:3 (one cement and three sand) 20 mm thick laid in situ and pointed with same coloured cement.

Dadooing walls with Glazed tiles of sizes 305mm X200mm X 6mm size of approved make and quality and colour I Set in cement mortar 1:2 (one cement,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Providing and fixing louvered ventilator fabricated from roll formed sections made of galvanized steel colour coated or reported they still as per IS 513 D quality galvanized as per IS 277 with the zinc of 120 grams per sqm) with the total coated thickness of Paint specification: court at sections should be with primer court of epoxy primer of 5-7 microns thick, Finish painted with polyester paint of 12 16 microns thick, Dimensions of the sections: the section for external frame should be 57 mm x 33 mm Fixing details: the section should be cut to length joint with profile to profile component Accessories: glass holding planes made of glass filled nylon Glass: louveres to be provided with 4 mm pin headed glass Grill: ventilator should be provided with grill made of 10 mm square MS bar to 12 mm x 5mm flat at 4 inch intervals. Total grill unit should be powder coated and fix it to ventilator frame with screws. The frames should be fixed to brick or concrete / Masonry walls and floor by means of self expaning screws

Supply and delivery and fixing of HDPE tank as per IS 12701/1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc...

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. Theprofiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

Manufacturing and supplying and fixing of steel doors with the following specifications. MS angles of size 40x 40x 6mm at 3.5 Kg./m are used for the outer frame and MS angle of size 35x 35x 5mm at 2.6 Kg/m for the shutter frames. Stiffeners with 32x6mm at 1.5 Kg./m MS flat is provided as the lockroll of the door and welded intact of both ends to the shutter frame 18g CR sheets of best quality is laid as panel in the shutter frames 18x5mm at 0.7 Kg./m MS flat is welded over the 32x6mm at 1.50 Kg./m MS flat on the rear side of the door sandwitching the CR sheet for rigidity. Additional stiffeners with 18x5mm at 0.7 Kg./m MB flats are provided diagonally onthe rear side of the shutter 2 Nos. of hinges in case of single leaf and 4 nos. of hinges in case of double leaf shutters is provided. 6 Nos. of hold fasts 120mm length spilced at the ends are wolded to the outer frame of the door. Tower bolt 2 Nos. one at the top and the other at the bottom are provided.

Supplying, fabricating, erecting structural steel work for roofing, and Gratings Work welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification as per Design given by the departmental officers etc, complete as per standard specification