CA NO GE S U 75 2022 23 PROVN OF TOILET GALVALUME SHEET uPVC PARTITION WITH SLIDING WINDOWS PATHWAY LED FITTINGS REROUTING OF SEWAGE LINE DRAINGE SEPTIC TANK RENEWAL REPLACEMENT OF EARTHING AND REPAIR REPLACEMENT OF ELECTRICAL WIRING AT CERTAIN LOC

Amount

Surface dressing n.exc 15 cm deep in hard/dense soil complete all as specified and as directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation complete all as specified and as directed.

PCC 1:4:8 type C2 (using 40 mm graded crushed stone aggregates) in foundation filling and mass concrete complete all as specified and as directed.

Brick work with sub class 'B' brick, straight or curved on plan exc 6M Mean radius built in type CM 1:6 complete as specified and as directed.

Returning filling in including spreading levelling watering and well ramming in layers not exc 25 cm complete as specified and as directed.

Removing excavated material n exc. 50m and depositing where directed at a level not exc 1.5 m above the starting point complete as specified and as directed.

Form work to edges of concrete flat slats sides of RCC/PCC bands etc in walls horizontal or sloping exc 10cm but n.exc 20cm wide rough finished surfaces complete as specified and as directed.

M&L for form work to soffits of suspended slabs and similar work not exceeding 200mm thick complete as specified and as directed.

RCC 1:1.5:3 type B1 using 20mm graded aggregates for slabs supported on walls beams in floors , roof , landing, balconies, canopies slabs and in shelves and the like complete as specified and as directed.

M&L form work to sides and soffit of floor or roof beams lintel, beam haunching ,girders lintel cantilever including supports overhung etc complete as specified and as directed.

RCC 1:1.5:3 type B1 using 20mm graded aggregates for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

RCC 1:1.5:3 type B1, 20mm graded crushed stone aggregates for lintel bands and roof bands complete as specified and as directed.

Mild Steel TMT bars 10 mm dia and over and cut to length bent to shape required including cranking, bending, hooking ends and binding with MS wire not less than 0.9mm dia or securing with clips quality conforming complete all as directed.

Mild steel TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups ,spacers and binder TMT bars cut to length bent to shape required including cranking, binding spirally including mild steel wire not less than 0.9 mm dia or securing with clips complete as specified and as directed.

Hard core of guage n exc. 63 mm deposited spread and levelled in layers n.exc. 15 cm thick watered and rammed to a true surface complete as specified and as directed.

75 mm thick PCC 1:4:8, type D-2 by using 40 mm graded crushed stone aggregate as in sub base floor complete as specified and as directed.

75 mm thick for PCC 1:3:6 using 20 mm graded crushed stone aggregate as in plinth protection using extra cement complete as specified and as directed.

M & L for non skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M & L for Glazed Coloured Ceramic tiles in vertical surface 300x450x7mm or 300x600x7mm thick laid over 10 mm thick screed bed in CM 1:4,set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Rendering 15 mm thick in CM 1:6 on brick work and finished even and smooth without using extra cement complete as specified and as directed.

Rendering 15 mm thick in CM 1:4 on brick work and finished even and smooth without using extra cement complete as specified and as directed.

Rendering 5 mm thick in CM 1:3 on ceiling and exposed surface of concrete finsihed even and smooth without using extra cement complete as specified and as directed.

M & L for preparation of new plaster surfaces of walls and applying two coats of oil emulsion distemper (white/tinted) complete all as specified and as directed.

M&L for preparation of new plaster surfaces applying two coats of cement base paint and over one coat of primers all as specified and directed

M&L for preparation of new plaster surfaces applying three coats of white wash on ceiling complete as specified and as directed.

S&F moulded solid PVC door frame of size 50x47mm made out of 5mm plain colour sheet reinforced with MS square tube complete all as specified and as directed.

S&F Moulded Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site complete all as specified and as directed.

S&F 100mm size butt hinges extruded aluminium alloy with galvanised with galvanised mild steel hinges pin anodised type B-22 complete all as specified and as directed.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section complete as specified and as directed.

S&F aluminium handles cast type of 150mm size complete as specified and as directed.

S&F steel Ventilators with top hung shutters including hinges steel peg stay, complete all as specified and directed .

S&F sheet glass 4 mm thick figured glass, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in Each pane complete as specified and as directed.

S&F GI tubes 15 mm dia medium grade laid in trenches or fitted on walls complete as specified and as directed.

S&F GI tubes 20 mm dia medium grade laid in trenches or fitted on walls /floor complete as specified and as directed.

S&F 110 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall complete as specified and as directed.

S&F 110 mm PVC (SWR) bends any radius with access door complete as specified and as directed.

S & F 100mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F 100 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall complete as specified and as directed.

Supply and fixing Vitreous china squatting pan, Orrisa pattern of size 580mmx440mm white with integral foot rest excluding flushing cistern and flush pipe complete as specified and as directed.

S&F 10 ltrs capacity PVC valve less syphonic action type flushing cistern low level with inlet ball valve float and handle complete all as specified .

S&F Vitreous china white wash hand basin (flat back or angle back type) size 550x400mm white including brackets, pedestal, wast fittings brass chromium plated, CP waste cupling, 32mm dia, waste pipe complete all as specified and directed.

S&F health faucet ABS body with wall hook and 1 mtr chrome plated PVC hose pipe complete all as specified.

S&F chromium plated toilet paper holder complete as specified and as directed.

S&F Glass shelf with chromium plated guard rails complete as specified and as directed.

S&F 600mm long brass chromium plated towel rail fancy type complete as specified and as directed.

S&F soap dish complete as specified and as directed.

S&F PVC waste pipe 32mm bore with cup and washers complete as specified and as directed.

S&F 15mm bore centre hole basin mixer with round spout with 450mm long copper pipes and brass nuts with out Pop up complete all as specified and as directed.

S&F Self closing angle cock pressmatic for urinal with flange and 200 mm connecting pipe and spreader complete all as specified and as directed.

S&F PVC connection 15mm bore 450 mm long Braided Hose with M10X1 Nipple, 15 mm Nut, O-Ring & Rubber washer (Suitable for Basin Mixers) complete all as specified and as directed.

S&F CP Bib taps cast copper alloy with crutch or butterfly handle two way, screwed for iron pipe of dia 15mm, fancy type fixed complete as specified and as directed.

S&F CP angle valves cast copper alloy,fancy type,with long shank and cup, bore15mm, fixed complete as specified and as directed.

S&F 125 mm dia brass chromium plated shower rose with swivel joints complete all as specified and as directed.

S&F 600 mm long tubular tower rail brass chromium plated 20mm dia, D type 60cm long fixed with two plugs (Gutties) of 2nd class hard wood embeded in cement mortar 1:3 with MS screws complete all as specified and as directed.

S&F Vitreous china bowl urinal flat back, size 465x355x265 mm white (min) with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete as specified and as directed.

S&F Rotational moulded polyethylene water storage tank 1000 ltrs (Cylinderical Verrtical with closed top) hoisted and fixed in position including 20mm dia ball valve of PTMT with epoxy coated aluminium rod & high pressure plastic ball and 20mm dia gate valve screwed with iron pipe all as specified shown in relevant SSR complete all as specified and as directed.

Roughing surfaces of New /old concrete surfaces by picking up , sweeping,cleaning and washing down with water to remove dust etc and brushing neat cement slurry @3kg/Sqm mixed with water proofing compound including 20mm thick screeding in CM (1:4) finished even and smooth compound (WPC shall be measured and paid separatley) complete as specified and as directed.

M&L Applying bituminous primer on roof surfaces @ 0.40 ltr/sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 kg/sqm and provide APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitumen 85/25 @ 1.2 kg/sqm blinded with fine sand in dry condition @ 0.5 kg/sqm including two coats of bituminious alluminium paint complete all as specified and as directed.

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in hard and dense soil complete all as specified and as directed.

Sand Cushioning 20 to 30 mm thick for laying and fixing interlocking tiles complete all as specified and as directed.

M&L machine pressed precast concrete interlocking paver block (glossy finish) any shape and size (sample as approved by GE) confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment. complete all as specified and as directed.

PCC 1:4:8 type D2 (Using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

PCC 1:2:4 type B-0 (12.5mm graded crushed stone aggregate) as in coping, benching, hanching and similar work etc including necessary form work complete all as spcified and directed.

Machine pressed (factory made) precast plain cement concrete 1:2:4 type B-1(20mm graded crushed stone aggregate), kerb stone & the like of size 300mm x 300mm x 100mm thick or of size as approved by GE, with plain fair faces including chamfers, weathering etc, embedding in position/laid in trenches on edges of roads, including excavation in any type of soil, setting in cement mortar (1:4) returning filling and removal of surplus soil/debris to a distance n.exc. 50m from the starting point, complete all as specified and directed.

Cement concrete 1:4:8 type D-2 (Using 40mm graded crushed stone aggregate) as in foundation filling and mass concerete complete all as specified and as directed.

M&L for SWG drain pipe grade 'A' of 150 mm internal dia laid in trenches and jointed in cement mortar (1:1) complete all as specified and as directed.

M&L Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete type D2 (1:4:8) for 150mm dia pipe complete all as specified and as directed.

M&L Precast reinforced cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate ) for manhole cover septic tank covers slabs etc including necessary form work and set in CM (1:4). complete all as specified and as directed.(Note:- reinforcement will be measured and paid seperately.)

Mild Steel TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for colunms, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Removing excavated soil to a distance exc 50m and nexc1.50 km out side defence land complete all as specified and as directed.

150 mm dia reinforced concrete pipes, class NP2, laid in trenches and jointed with cement mortar 1:2 complete with collars complete all as specified and as directed.

Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete type D2 (1:4:8) for 150mm dia pipe complete all as specified and as directed.

Brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius built in CM (1:4) as in manholes, septic tank, filter bed, walls, drains etc complete all as specified and as directed.

Demolition Cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Precast reinforced cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) for manhole cover septic tank covers slabs etc including necessary form work and set in CM (1:4) complete all as specified and as directed.

RCC Septic tank (50 users capacity) designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 Design Mix in Walls , Base Slab , Baffle walls and Roof Slab including beams etc with Vent shaft , manhole openings with cover connection etc., complete with effective depth of 1.5 meter and overall depth of 3 meter complete all as specified and as directed.

Demolition of cement concrete in ground floor and paving n exc 15 cm thickness below and above ground level and as in floor complete all as specified.

M&L Reinforced concrete pipe 600mm dia, class NP-2 laid to floor and wall jointed complete with collars complete all as specified and as directed.

M&L for concrete bed to drain pipes 600mm dia type 1:3:6, C-2 including paking under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed.

Providing cement concrete 1:2:4 Type B1 using 20mm graded aggregate as in lintels up to 1.5m clear span, cills, seismic and other similar bands, plinth courses, copings, Bed blocks, and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified.

PCC 1:2:4 Type B-1 using 20 mm graded aggregate in surface channels and drains complete all as specified.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block (Glossy finished) of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

M&L Providing cement concrete 1:2:4 Type B1 using 20mm graded aggregate in roof kerbs of mud stops rounded or chamfered on edges complete all as specified and as directed.

Excavating in post holes (or similar holes ) each n.exc 0.5 cum in soft /loose soil getting out ,returning filling in and ramming around in layers not exceeding 25 cm complete all as specified and as directed.

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to Fe 410-W (Gde-E-250 quality A) complete all as specified and as directed.

S&F rolled mild steel Fe-410w (Gde-E-250) quality 'B' Roof trusses (framed ) , trussed, purlins, crane gantries , rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces cleats etc complete all as specified and as directed.

S&F Pre-Painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 MPa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-Painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 MPa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M & L for applying two coats of synthetic enamel ordinary tint paint including red oxide primer and preparation extra complete on new steel or iron surfaces of any description, over 10cm in width or grith, not otherwise described complete all as specified and as directed.

S & F MS plates (plain or chequered) channels, square cut or notched ordinary and counter sunk) with riveted, bolted or welded attachment complete all as specified and as directed.

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) (A) Area not exceeding 2.00 sqm each complete all as specified and as directed.

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and as directed. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing factory made uPVC white colour Casement door with top hung ventilator with 3D and SS friction (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 + 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.50 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

8mm thick Toughned glass as in hinged doors/window, partitions automatic doors and similar work including cutting to shape, drilling holes of tinted/one side view as required complete all as specified and as directed.

10mm thick Toughned glass as in doors, automatic doors and similar work including cutting to shape, drilling holes including floor door closure and all acessories as required complete all as specified and as directed.

18/20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window sills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

Vitrified tiles light Shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

Taking down cement or cement lime plaster of any description on brick or stone walls and concrete surface etc including raking out joints hacking for key scrubbing down with water etc complete all as specified and as directed.

Applying 1mm thick wall care putty on wall complete all as specified and as directed

M&L for applying two coat of plastic emulsion paint to new or old plastered surfaces at brick masonry/concrete surface over cm 10 width or girth including a cot of primer complete all as specified.

Excavation over area not exceeding 1.50 Mtrs in deep and getting out in soft/loose soil complete all as specified and as directed.

Removing excavated soil material exc. 250m but n.exc 500m and depositing where directed at a level not exc. 1.5m above the base in soil complete all as specified and as directed.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregates as in cobbing/gola or edging to jam the paver block all as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

Screed bed or bedding layers of 15 mm thick cement mortar 1:3 for laying floor finishes complete all as specified and as directed.

25 mm thick PCC 1:2:4 type B1, using 20mm graded crushed stone aggregate as in sub base for laying floor finishes all as specified and as directed.

Coloured Chequered tiles lacquer finish of size 30cmx30cmx20-25mm thick, set jointed and pointed in neat cement slurry as in path with white cement and pigment etc complete all as specified and directed.

Machine pressed (factory made) precast plain cement concrete 1:2:4 type B-1(20mm graded crushed stone aggregate), kerb stone & the like of size 300mm x 300mm x 100mm thick or of size as approved by GE, with plain fair faces including chamfers, weathering etc, embedding in position/laid in trenches on edges of roads, including excavation in any type of soil, setting in cement mortar (1:4) returning filling and removal of surplus soil/debris to a distance n exc 50m from the starting point, complete all as specified and directed.

Point wiring for one light/ fan/bell point controlled by one switch using 1.5 Sq mm FRLSH copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit as per site requirement (thickness not less than 1.5mm and 20mm dia), medium grade with Modular sunken boxes & PVC back plate for mounting modular type switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire stranded and conected to earth dolly complete all as specified and as directed. Note:- Cutting and making same the wall patchs after laying the wire and conduit using putty, white wash and distamper. The surface should be made smooth using putty and should match exactly with the existing wall finish.

All as per srl item No 111 above, but for 3 pin 5 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per srl item No 111 but for 3 pin 6 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per Srl item No 111 but for 3 Pin 15 Amps socket outlet independent with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly complete all as specified and as directed.

All as per srl item No 111 but for 3 pin 10 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per srl item No 111 but for 3 pin 10 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per Srl item No 111 but for 3 Pin 20 Amps socket outlet independent with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly complete all as specified and as directed.

S&F modular switch 6 Amps single pole one way 230 volt with outer strip complete all as specified and as directed.

S&F modular switch 16 Amps single pole one way 230 volts with outer strip complete all as specified and as directed.

S&F modular socket 3 Pin 6 Amps flush type with outer strip complete all as specified and as directed.

S&F modular socket combined 2-in-1, 6 Pin 6 & 16 Amps flush type with outer strip complete all as specified and as directed.

Ceiling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Block complete all as specified and as directed.

S&F Sheet metal enclosure double door type for DBs (when MCB to be used) 12 way 240 volts with 200 Amps rated busbar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed.

S & F in replacement of MCB Single pole and neutral 240 volt any rating from 40 amps 'C' series, with rupturing capacity 10 KA, inculding providing thimble for out going cable complete all as specified and as directed.

S & F in replacement of MCB single pole 240 volt any rating from 10 to 40 amps 'C' series, with rupturing capacity 10 KA, inculding providing thimble for out going cable complete all as specified and as directed.

S&F Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 6 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead including taking down old sub main wire complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20W, 230V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp,clamps,suitable bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Supply and fixing exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers along with all electrical wire connection all as specified and as direceted.

Supply & Laying in trenches or passing through pipe or on wall , 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 25 Sqmm x 3.5 core size all as specified including taking down old cable complete all as specified and as directed. Note : Earth work and other connected work shall be measured & paid sperately.

Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power) complete fitting such as switch, sockets, ceiling rose, fan regulator,pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as specified and as directed.

Call bell ding-dong 230 volts including taking down old one complete all as specified and as directed.

S&F Bell push, flush type, 5 amp complete all as specified and as directed.

S&F in replacement of MCB Single Pole and Neutral , 230 Volt, Raiting 40 to 63 Amps complete all as specified and as directed.

S &F in replacement of Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 12 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed.(Note-MCBs will be measured separately).

S & F Sheet metal enclosure MCB distribution board Triple pole & neutral 415 volts 4 way C Curve with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed. (Note-MCBs will be measured separately)

Supply & Fixing MCB TPN 100 Amp, 4 Pole, 415V C Curve complete all as specified and as directed.

S & F in replacement of sheet metal enclosures for DBs when MCBs to be used double door DB VTPN MCCB 125A 4way IP43 Protection Cat Pt No - 811888 with 125A MCCB 16kA complete all as specified and as directed. Make: Indoasian, Cat Partt No - 830153 or equivalent.

S&F fan regulator electronic, stepped type hum free suitable control speed of fan from 0 to 100 % and connecting electrically complete all as specified and as directed.

Supply and fixing LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

S&F in replacement of LED Street light 40W including angle arms (Bracket) with 25mm dia GI pipe complete all as specified and as directed. Cart Pt No - ENDURAPEARLNEOSL40WLED757PASYTOPC or equivalent complete all as specified and directed by Engineer-in-Charge.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Taking down/refixing ceiling fan/Exhaust Fan including disconnection of existing connection, dismanting of blades and Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and rehanging the fan complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 10 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead including taking down old sub main wire complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 6 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 4 Sq mm as earth lead including taking down old sub main wire complete all as specified and as directed.

M&L Earthing complete with galvanised steel earth plate electode 600mm x 600mm x 6.00mm thick burried directly in ground (earth pit not less than 2.25 meter deep below normal ground level connected to and including galvanised steel earth lead wire 4 mm dia by means of bolts, nuts, chock, nuts and washers of galvanised iron or steel including PCC Pit in 1:2:4 type B-I angle iron frame with RCC cover and handle, excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mash and light grade GI protection pipe 15mm bore upto main board complete all as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected to main control board as specified and testing completion complete all as specified and as directed.

Supply & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 35 Sqmm x 3.5 core size including taking down old cable complete all as specified and as directed. Note : Earth work and other connected work shall be measured & paid sperately.

Supply & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 25 Sqmm x 3.5 core size including taking down old cable complete all as specified and as directed. Note : Earth work and other connected work shall be measured & paid sperately.

Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete all as specified and as directed. Note : for payment purpose punned thickness shall be measured

M&L Bricks sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and as directed.

Supply and fixing GI tubing light grade 40 mm dia along the wall/ in trenches/ in duct / in culvert /road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles complete all as specified and as directed.

Taking down carefully copper/aluminium sub main wiring of size 2.5/4/6 sqmm from surface/concealed at any height and removing the materials from site and making good the disturbed surfaces of walls,floors roofs etc complete all as specified and as directed.

Taking down Old/ Unserviceable MCB DBs TPN / Main Switches by disconnection of electric connection including old unserviceable MCCBs,MCBs, isolators etc and making good to distrubed surface complete all as specified and as directed.

Disconnecting and taking down un serviceable light fittings of any description/ capacity complete all as specified and as directed.

Supply & fixing sheet metal enclosure Double pole with 2 pin and earth plug and socket 25A 240 Volt complete with one double pole MCB of 20 A "C" Series of breaking capacity 10 KA all as required at site complete all as specified and as directed.

S&F Sheet metal enclosure double door type for MCCB TPN DB upto 125 Amps, 4 way vertical type 415 volts with 400 Amps rated busbar and neutral link including MCCB 125 Amps 16 KA , chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed.

S & F sheet metal enclosures for DBs when MCBs to be used double door DB SPN 8 way 240 volts with 200 amps rated bus bar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed.

S & F in replacement MCCB Three Pole & Neutral capacity of 125 amps 415 volts rupturing capacity 16 KA complete all as specified and as directed.

S&F Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 4 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 4 Sq mm as earth lead including taking down old sub main wire complete all as specified and as directed.

Supply and fixing Rigid non-metallic PVC conduit of size 32 mm dia for cabling of telephone wire etc exclusive of boxes (junction/ terminal) but inclusive of all tees, bends,elbows, reducers, bell mouth tube ends clamping and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type 4 feet with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 10W, 220V,AC decorative box type 2 feet with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing LED luminaire 15 watt, 220 V AC recess mounted downlighter type with high efficiency PC diffuser soft light and Symmetrical illumination complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing LED luminaire 12 watt, 220 V AC recess mounted down lighter type with high efficiency PC diffuser soft light and symmentrical illumination complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing LED luminaire 2X2R 28 watt, 220 V AC recess mounted downlighter type with high efficiency PC diffuser soft light and symmentrical illumination complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing Square shape 2'X2', 34 watt 220 volts AC surface mounted type with high efficiency soft light and symmentrical illumination complete with drivers, holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F decorative wall mounting Lamp/Candle Lamp chrome finish fixture with frosted glass suitable for 4 W mini GLS lamp luminaire complete all as specified and as directed.

Supply and Installation of Maintenance Free (Chemical) earthing system complete with 03 (One) Nos. UL listed copper clad MS Rod Electrode, Each of 17.2 mm dia, 3000mm long electrode buried in a bore hole of 100 mm dia. Vertically to a depth not less than 3 Mtr deep below ground level with top edge earth electrode at a depth not less than 300 mm below normal ground level. All Three Earth pit must be in a distance of 2.5Mtr and connected to each other by 25mmX3mm Copper Strip to make Ring Earth. Provision of 01 (One) Nos. of copper bus bar of size 100mmX25mmX5mm for connection with copper earth lead strip 25mmX2mm and further connected to test point terminal of size 200mmX50mmX6mm made of copper as directed, including 40 Kg (Minimum) back fill chemical compound conforming to IEC 62561-7 standards for filling in each bore holes, so as to achieve earth resistance below 2 Ohms & Poly plastic pit covers tested for 5 ton load bearing 1/pit complete all as specified and as directed.

Supply and fixing Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in GI Tubing pipe or fixed to poles or any other indicated situation for loop earthing etc as required 20 x 3mm Copper Strip to test point ternimal as down conductor, roof conductor and continuous earth lead to test point terminal including taking down of old rusted copper strip comlete all as specified and as directed. Note : All the jonts shall be made with copper brazing to get proper conductivity.

SINGH CONST CO

M/S ASHOK KUMAR PACHIALA

khajuria builders

RAMAN CONSTRUCTION CO

VIRINDER SINGH

VISHWANATH AND SONS

vmd traders

MADAN LAL SHARMA AND SONS

K S BUILDERS

TARUN BUILDERS

BHAGWATI TRADERS

PARDEEP SHARMA