REPAIR/REPAINTING OF STEEL FURNITURE, RE-CANNING POLISHING OF WOODEN FURNITURE AT UNIT LINES, MARRIED ACCN AND FURNITURE UNDER GE 869 EWS AT LEIMAKHONG MIL STN

Amount

Schedule 'A'

Removing the existing unserviceable tops from the following tables and supply and fix new top of 18/19 mm thick commercial block board with 1 mm thick plastic laminated sheet fixed on top 4 mm thick teak wood edging shall be provided al-round the top.all as shown on drawing and specified . (1.01) Table 3'x 2' with drawers FD-224/383

(1.02) Table 3'x 2' without drawers FD-223/384

(1.03) Table 2'x2' wooden FD-293

(1.04) Table Centre FD-235/274

(1.05) Table peg FD-277

(1.06) Teapoy FD-278

(1.07) Table dining 6 Persons FD-239/273

(1.08) Table dining 6 pers MAP FD/E6/MAP/0

(1.09) Table dining 4 pers FD/MAP II/03

(1.10) Table dining 8 Persons FD-273

(1.11) Table Writing FD-275

(1.12)Table writing med (Study table) DB/WDF-10

(1.13) Table office officer wooden WFD-32

(1.14) Table office clk wooden DB-4120

(1.15) Table Office clerk steel FD-1004

(1.16) Table office Officer steel FD-1003

(1.17) Table office senior officer steel FD-1002

(1.18) Teapoy Verandah FD-255

(1.19) Table 900 mm x 600mm with drawer steel FD-1008

(1.20) Table 900 mm x 600mm without drawer steel FD-1007

(1.21) Table 900 mm x 900 mm steel FD-1009

Removing the existing unserviceable front and back long rail from the following tables and supply and fix new front and back long rail of teak wood/Hollock/Bonsum size, shape & design as shown on drg All new surfaces shall be two coat of french polish with high gloss finish. (2.01) Table 3'x 2' with drawers FD- 224/383

(2.02) Table 3'x 2' without drawers FD- 223/284

(2.03) Table Centre FD- 235/274

(2.04) Table peg FD- 277

(2.05) Teapoy FD- 278

(2.06) Table dining 6 Persons FD- 239/273

(2.07) Table dining 8 Persons FD-273

(2.08) Table Writing FD- 275

(2.09) Table 2'x2' wooden FD-293

(2.10) Table dining 6 pers MAP FD/E6/MAP

(2.11) Table dining 4 pers MAP FD/MAP/II/03

(2.12) Table office officer wooden WFD-32

(2.13) Table office clk wooden DB- 4120

Ditto all as per item No 22.00 here-in- above but short side rail. (3.01) Table 3'x 2' with drawers -FD 224/383

(3.02) Table 3'x 2' without drawers -FD 223/284

(3.03) Table Centre -FD 235/274

(3.04) Table peg -FD277

(3.05) Teapoy -FD 278

(3.06) Table dining 6 Persons -FD 239/273

(3.07) Table dining 8 Persons -FD 273

(3.08) Table Writing -FD 275

(3.09) Table 2'x2' wooden -FD 293

(3.10) Table dining 6 pers MAP -FD/E6/MAP

(3.11) Table dining 4 pers MAP -FD /MAP II/03

(3.12) Table office officer wooden -WFD- 32

(3.13) Table office clk wooden DB-4120

Ditto all as per item No 22.00 here-in- above but Legs. (4.01) Table 3'x 2' with drawer - FD 224/383

(4.02) Table 3'x 2' without drawers - FD 223/284

(4.03) Table Centre - FD 235/274

(4.04) Table peg - FD 277

(4.05) Teapoy - FD 278

(4.06) Table dining 6 Persons - FD 239/273

(4.07) Table dining 8 Persons - FD 273

(4.08) Table Writing - FD 275

(4.09) Table 2'x2' wooden - FD293

(4.10) Table dining 6 pers MAP - FD /E6/MAP

(4.11) Table dining 4 pers MAP - FD /MAPII/03

(4.12) Table office officer wooden - WFD 32

(4.13) Table office clk wooden - DB4120

Removing the existing unserviceable front leg from following chair and S&F new teak wood front leg complete all as directed and shown on drg (5.01) but Chair dining FD - 279

( 5.02) All as per Ser No 61 but Chair dining MAP - FD/MAPII/05

( 5..03) All as per Ser No 61.00but Chair Dining Officers (MAP) - FD/MAPII/04

(5.04) All as per Ser No 61.00 but Chair dining long Back - FD357

(5.05) All as per Ser No 61.00 but Chair Writing FD 280

(5.06) All as per Ser No 61.00 but Chair Easy FD 229

Removing the existing unserviceable rear leg from following chair and S&F new teak wood rear leg complete all as directed and shown on drg ( 6.01) Chair dining FD -279

(6.02) All as per Ser No 67.00 but Chair dining MAP - FD /MAPII/05

(6.03) All as per Ser No 67.00 but Chair Dining Officers (MAP) - FD/MAPII/04

(6.04) All as per Ser No 67.00 but Chair dining long Back - FD- 357

(6.05) All as per Ser No 67.00 but Chair Writing FD - FD-280

(6.06) All as per Ser No 67.00 but Chair Easy FD - FD- 229

Removing the existing unserviceable front rails from following chair and S&F new teak wood front rails complete all as directed and shown on drg ( 7.01) but Chair dining MAP - FD/MAP II/05

( 7.02) All as per Ser No 73.00 but Chair Dining Officers (MAP) - FD/MAP II/04

(7.03) All as per Ser No 73.00 but Chair dining long Back - FD357

Removing the existing unserviceable side rails from following chair and S&F new teak wood side rails complete all as directed and shown on drg (8.01) but Chair dining MAP - FD/MAPII/05

(8.02) All as per Ser No 76.00 but Chair Dining Officers (MAP) - FD/MAPII/04

(8.03) All as per Ser No 76.00 but Chair dining long Back - FD357

Removing the existing unserviceable stiffiner from following chair and S&F new teak wood side rails complete all as directed and shown on drg (9.01) but Chair dining FD FD-279

( 9.02) All as per Ser No 79 but Chair dining MAP - FD/MAP/II/05

(9.03) All as per Ser No 79.00 but Chair Dining Officers (MAP)-FD/MAP/II/04

(9.04) All as per Ser No 79.00 but Chair dining long Back FD-357

(9.05) All as per Ser No 79.00 but Chair Writing FD-280

(9.06) All as per Ser No 79.00 but Chair Easy FD-229

SOFA SETs (FD-281) & FD/MAP-II/02, Removing the existing unserviceable cushion and replacing with new 100mm thick cushion of 'cool' foam of 32 density 530 mm x 500 mm covered with best quality of tapestry cloth Make - Sleepwell/Kurlon all as shown on drgs and as approved by GE. Note :- Each cushion for seat or back will be measured as single unit and tapestry cloth should not be less than Rs.350/Mtr

SOFA SETs (FD-281) & FD/MAP-II/02, Removing the existing unserviceable leg from Sofa FD-281 and S & F new teak wood/Hollock/Bonsum leg all as shown on drg and directed by Engr- in -Charge.

SOFA SETs (FD-281) & FD/MAP-II/02, Removing existing unserviceable Arm rest from Sofa FD-281 and S & F new teak wood/Hollock/Bonsum Arm Rest all as shown on drawing and specified .

SOFA SETs (FD-281) & FD/MAP-II/02,Removing existing unserviceable side rail from Sofa FD-281 and S & F new teak wood/Hollock/Bonsum side rail all as shown on drawing and specified .

SOFA SETs (FD-281) & FD/MAP-II/02,Removing existing unserviceable bearer from Sofa FD-281 long pieces and S & F new teak wood/Hollock/Bonsum bearer all as shown on drawing and specified .

SOFA SETs (FD-281) & FD/MAP-II/02,Removing existing unserviceable bearer from Sofa FD-281 single pieces and S & F new teak wood/Hollock/Bonsum bearer all as shown on drawing and specified .

SOFA SETs (FD-281) & FD/MAP-II/02,Removing existing unserviceable battens from Sofa FD-281 and S & F new teak wood/Hollock/Bonsum battens all as shown on drawing and specified .

SOFA SETs (FD-281) & FD/MAP-II/02,Removing existing unserviceable front rail from Sofa FD-281 long pieces and S & F new teak wood/Hollock/Bonsum front rail all as shown on drawing and specified .

SOFA SETs (FD-281) & FD/MAP-II/02,Removing existing unserviceable front rail from Sofa single FD-281 pieces and S & F new teak wood/Hollock/Bonsum front rail all as shown on drawing and specified .

Removing the existing unserviceable mirror and S & F new mirror of size 380mm x 760mm and 5 mm thick make modiguard /swastic/saint gobain with back and frame all as specified and shown on drgs including with teak wood support approved quality and shown on drags including with teak wood support.` ( Table dressing with Mirror Gents, FD- 230/FD/E6)

Removing the existing UNSV drawers and supply & fixing of new drawer as shown on drgs and specified ( Table dressing with Mirror Gents, FD- 230/FD/E6)

Removing existing unserviceable plywood portion of back of Mirror and S&F new back made out of 6 mm thick plywood for mirror all as shown on drgs ( ( Table dressing with Mirror Gents, FD- 230/FD/E6)

Removing the existing broken glass shutters and S&F new Glass shutters all as shown on drg (Each glass shutter shall be measured as single unit) ( Table dressing with Mirror Ladies, FD-251)

Removing the existing unserviceable Aluminium channel and S & F new Aluminium Channel all as shown on drgs ( Table dressing with Mirror Ladies, FD-251)

Removing existing unserviceable plywood portion of back of Mirror and S&F new back made out of 6 mm thick plywood for mirror all as shown on drgs ( Table dressing with Mirror Ladies, FD-251)

Removing the existing unserviceable mirror and S&F new mirror 5 mm thick of make modiguard/Saint Gobain with complete frame and back all as shown on drgs . ( Table dressing with Mirror Ladies, FD-251)

Removing the existing unserviceable 12mm ply wood from back and S&F new back of table dressing ladies made out of 12 mm thick plywood commercial quality all as shown on drgs and specified. ( Table dressing with Mirror Ladies, FD-251)

Removing the existing unserviceable seat and S&F new seat made out of teak wood in natiral polish with polythene cane in Godrej pattern confirming to IS -5378:94 (type-I.0 and fixing with suitable screw to chair CBA steel with arms . Rest all as shown on drgs and specified. ( FD- 75M)

Removing the existing unserviceable back and S&F new back made out of teak wood in natiral polish with polythene cane in Godrej pattern confirming to IS -5378:94 (type-I.0 and fixed with suitable screw to chair CBA steel with arms. Rest all as shown on drgs and specified. ( FD- 75M)

Removing of existing unsv pvc shoe and supply & fixing of new pvc shoe of chair CBA steel with arms ( FD- 75M)

Removing of existing unsvwooden arms rest and supply & fixing of new wooden arms rest with screw of suitable size of chair CBA steel with arms ( FD- 75M)

Plate welding-supply and welding 3mm thick plate to bottom of seat chair CBA steel with arms all as shown on drawing and as directed by Engr-in-Charge ( FD- 75M)

Removing the existing unserviceable seat and S&F new seat made out of teak wood in natiral polish with polythene cane in Godrej pattern confirming to IS -5378:94 (type-I.0 and fixing with suitable screw to chair CBA steel without arms . Rest all as shown on drgs and specified. ( FD- 75 (M))

Removing the existing unserviceable back and S&F new back made out of teak wood in natiral polish with polythene cane in Godrej pattern confirming to IS -5378:94 (type-I.0 and fixed with suitable screw to chair CBA steel without arms. Rest all as shown on drgs and specified. ( FD- 75 (M))

Removing of existing unsv pvc shoe and supply & fixing of new pvc shoe of chair CBA steel with out arms ( FD- 75 (M))

Plate welding-supply and welding 3mm thick plateto bottom of seat chair CBA steel with out arms all as shown on drawing and as directed by Engr-in-Charge ( FD- 75 (M))

Removing the existing unserviceable hand rest and S&F new hand rest of chair CBA special with hand as shown on drgs and specified by Engr-in-charge. ( FD- 120 (M))

Removing the existing unserviceable hand board and S&F new hand board of chair school with hand board as shown on drgs and specified by Engr -in-charge. FD/E6/MAP/05

Removing the existing unserviceable PVC seat and S&F new PVC sheet of chair school with hand board complte as shown on drgs and specified by Engr-in-charge. FD/E6/MAP/05

Removing the existing unserviceablePVC back and S&F new PVC back of chair school with hand board as shown on drgs and specified by Engr-in-charge. FD/E6/MAP/05

Removing the existing unserviceable Seat from Chair writing steel MAP and S&F of new Seat (12 mm hot pressed ply wood, upholstered with fabric and moulded polyurethane foam. with PVC lipping all around to them in all respect of Make : Godrej or equivalent approx size of seat 510 x 470 x 60) to Chair writing steel MAP all as shown on drg and as directed by Engr-in-Charge. FD/E6/MAP/12

Removing the existing unserviceable Back from Chair writing steel MAP and S&F of new Back (12 mm hot pressed ply wood, upholstered with fabric and moulded polyurethane foam. The back form shall be designed with contour lumber support for extra comfort with PVC lipping all around to them in all respect of Make : Godrej or equivalent approx size of seat 510 x 470 x 60) to Chair writing steel MAP all as shown on drg and as directed by Engr-in-Charge. FD/E6/MAP/12

Plate welding-supply and welding 3mm thick 45mm dia MS bottom plate for Chair writing steel MAP all as shown on drawing and as directed by Engr-in-Charge FD/E6/MAP/12

Removing the existing unserviceable Arms from Chair writing steel MAP and S&F of new Arms to Chair writing steel MAPall as shown on drg and as directed by Engr-in-Charge. FD/E6/MAP/12

Removing the existing unserviceable Seat from Chair CB steel and Chair CBA steel and S&F of new Seat (12 mm th hot pressed ply wood, upholstered with fabric and moulded polyurethane foam. with PVC lipping all around to them in all respect of Make : Godrej or equivalent ) to Chair CB steel and Chair CBA steel all as shown on drg and as directed by Engr-in-Charge. HFD-2044,HFD-2045

Removing the existing unserviceable Back from Chair CB steel and Chair CBA steel S&F of new Back (12 mm th hot pressed ply wood, upholstered with fabric and moulded polyurethane foam. The back form shall be designed with contour lumber support for extra comfort with PVC lipping all around to them in all respect of Make : Godrej or equivalent ) to Chair CB steel and Chair CBA steel and all as shown on drg and as directed by Engr-in-Charge. HFD-2044,HFD-2045

Removing the existing unserviceable Arms from Chair Chair CBA steel and S&F of new Arms to Chair CBA steel all as shown on drg and as directed by Engr-in-Charge. HFD-2044,HFD-2045

Preparing the wood surface by scraping and filling bore holes with putty and rubbing by sand paper/Abbrassive cloth throughly smooth and clean off and applying one coat of french polish of the required finishing of Table 3'x2' with Drawer & without drawer FD-248

All as per item No. 122 but Table Dressing Gents FD- 251

All as per item No. 122 Table Dressing Ladies FD- 246

All as per item No. 122 Bed plywood top FD- 244

All as per item No. 122 Chair dining FD- 279

All as per item No. 122 Chair dining JCO/OR Map PVC FD/MAPII/04, HFD

All as per item No. 122 Chair Easy FD - 250

All as per item No. 122 Chair writing FD- 233

All as per item No. 122 Chair dining long Back FD- 357

All as per item No. 122 Chair dning officer MAP FD/MAP II/ 04, FD- 2030

All as per item No. 122 Peg table, FD- 281

All as per item No. 122 Sofa Set 5 Seater, FD- 281

All as per item No. 122 Sofa Set single Seater, FD- 281

All as per item No. 122 Sofa Set 5 Seater MAP, FD/ MAP -II/02

All as per item No. 122 Stool Dressing, FD- 284

All as per item No. 122 Table Centre, FD- 235/274

All as per item No. 122 Table dining 6 persons, FD-239

All as per item No. 122 Table dining 8 persons, FD- 273

All as per item No. 122 Table office clk wooden, DB- 4120

All as per item No. 122 Table office officer wooden, WDF- 32

All as per item No. 122 Table writing , FD- 232

All as per item No. 122 Teapoy, FD- 276

All as per item No. 122 Table dining 4 pers, FD/MAPII/03

All as per item No. 122 Table dining 6 pers MAP, FD/E6/MAP

All as per item No. 122 Table 2'x2' wooden, FD- 293

All as per item No. 122 Almirah mess utensil, FD-83

All as per item No. 122 Notice board 2400x1220mm and Notice board 1830x1220mm, FD-99

All as per item No. 122 Hat stand with mirror, FD- 362, 223, 233

All as per item No. 122 Chair Easy Cushioned, FD- 358

All as per item No. 122 Rack for Record 6'x2'x6', DB3593

M&L for cleaning/preparing the existing surfaces ie. de-rusting, filling putty, denting of steel surfaces and applying two coats of synthetic enamel paint as approved by Garrison Engineer by spray process to achieve a uniform finish of Chair CBA steel with or without arms FD- 75 (M)

All as per item No. 152 Chair CBA special with hand rest Fd- 102 (M)

All as per item No. 152 Chair school with hand board FD/E6/MAP/05

All as per item No. 152 Chair writing steel MAP , FD/E6/MAP/12

All as per item No. 152 Chair CB steel and Chair CBA steel , HFD- 2044, HFD- 2045

All as per item No. 152 Chair Verandah, FD- 256, Fd/E6/MAPII

All as per item No. 152 Ladder for loft, FD- 238

All as per item No. 152 Rack side steel with 3/4 spaces FD- 1023 & HFD- 2039

All as per item No. 152 Rack shoe steel MAP, FD/E6/MAP/01

All as per item No. 152 Rack side steel 6 tier , F- 1038, FD-106 (M), 129 (M) & HFD- 2039

All as per item No. 152 Stool Steel 315x315x610mm, FD-81 (M)

All as per item No. 152 Table 3'x2' Steel with Drawer , FD- 1008

All as per item No. 152 Table 3'x2' Steel without Drawer ,FD- 1007

All as per item No. 152 Table 900x900x760mm Steel (3'x3'), FD- 1009

All as per item No. 152 Trestle Store Room Steel, FD- 1043

All as per item No. 152 Table Office Clerk Steel with Drawers, FD- 1004, HFD- 251

All as per item No. 152 Table Office Officer Steel, FD- 1003, HFD- 2050

All as per item No. 152 Table Senior Officer Steel 1800x1200x760mm, FD- 1002

All as per item No. 152 Table Dining ORs with Aluminium Top, FD- 165 (M)

All as per item No. 152 Locker steel, FD- 1029

All as per item No. 152 Almirah large steel, FD- 67, FD- 1031, HFD- 2055, FD- 1033, HFD- 2060

All as per item No. 152 Almirah medium/small steel- FD-1032, FD-243. HFD-2056, FD-1033, HFD-2056

All as per item No. 152 Book Case Steel Large Glazed- FD- 1028

All as per item No. 152 MNF Set - FD- 145

Removing the existing unserviceable/damage/ broken legs for lockers steel and S&F with a new legs and applying one coat of synthetic enamel paint over one coat of red oxide primer including welding to the locker and all as specified and shown on drgs in addition to provide rubber pad in 3mm thick to be provided for legs. FD- 1029

Removing the existing unserviceable/damaged shelves for locker steel and S&F MS sheet CRC 1mm thick bent to shape and applying one coat of synthetic enamel paint over one coat of red oxide primer including welding to the locker/clips and all as specified and shown on drg. FD- 1029

Removinf the existing unserviceable/damaged heps and staple for locker steel and S&F with a new heps and staple all as approved by Garrison Engineer. FD- 1029

Removing the unserviceable PVC seat from Chair Dining (MAP) and supply and fix new suprior quality PVC seat. All as shown on drg and as directed by Engr-in-Charge. FD/MAP-II/05

Taking out old unsv seat from chair dining long back and Supply and Fixing new 75mm thick foam cushion of 32 Density shall be fixed on 12mm thick BWR plywood of seat with new existing size and shape alongwith cover foam shall be upholsted with leatherised rexene of approved shade and texture of best quality as approved by Engr-in-Charge shall be provided. Make of foam shall be Kurlons/Sleep well. FD- 357

Taking out old unsv back rest from chair dining long back and supply and fixing new 50mm thick foam cushion of 32 density shall be fixed on 12mm thick BWR plywood of back rest with new existing size and shape alongwith cover foam shall be upholsted with leatherised rexene of approved shade and texture of best quality as approved by Engr-in-Charge shall be provided. Make of foam shall be Kurlons/Sleep well. FD- 357

Removing the unserviceable PVC shoe from chair dining long back and supply and fix new PVC shoe suprior quality chair dining long back. All as shown on drg and as directed by Engr-in-Charge. FD- 357

Taking out old unsv seat from chair dining offr MAP and Supply and Fixing new 75mm thick foam cushion of 32 Density shall be fixed on 12mm thick BWR plywood of seat with new existing size and shape alongwith cover foam shall be upholsted with leatherised rexene of approved shade and texture of best quality as approved by Engr-in-Charge shall be provided. Make of foam shall be Kurlons/Sleep well. FD/MAP-II/04

Removing the unserviceable PVC shoe from chair dining officer MAP and supply and fix new PVC shoe suprior quality chair diningofficer MAP. All as shown on drg and as directed by Engr-in-Charge. FD/MAP-II/04

Removing the existing unserviceable three way locking device and S&F three way locking device with cover all as directed by the Engr in Charge and shown on drgs for almirah large steel FD-1032 FD-1031 HFD-2056, FD-1033

All as per item No 185 herein before but almirah medium/small steel FD-1032 FD-1031 HFD-2056, FD-1033

Removing the existing unserviceable locks and S&F locks of appropriate size 6 levers with duplicate keys chromium plated Make Godrej (product No 3936) or equivalent as suitable in almirah with suitable fixing arrangement all as directed by Engr in Charge and shown on drgs for almirah large/medium steel. Notes : (i) Unit rate quoted shall include for provision/repairs to back plate cover to key hole back side cover locking device etc. (ii) Steel chromium plated handle shall be measured and paid separately. FD-67, FD-230, FD-1031, FD-1032 , HFD-2056, FD-1033

Removing the existing unserviceable handle and S&F new chromium plated handle 125mm long to almirah large/medium/small steel all as specified/directed and shown on drg. FD-67, FD-230, FD-1031, FD-1032 , HFD-2056, FD-1033

Removing the existing unserviceable/damaged/ broken legs for almirah large and S&F with a new legs made out of 18 G sheet with applying one coat of red oxide primer including welding to the almirahs and all as specified and shown on drgs. FD-67, FD-230, FD-1031, FD-1032 , HFD-2056, FD-1033

Removing the existing unserviceable/damage/broken legs for almirah medium and S&F with a new legs made out of 18 G sheet with applying one coat of synthetic enamel paint over one coat of red oxide primer including welding to the almirahs and all as specified and shown on drgs. FD-67, FD-230, FD-1031, FD-1032 , HFD-2056, FD-1033

Removing the existing unsv/broken glass from shutter to book case steel glazed and supply and fixing of new glass all as per drg and as directed by Engr-in-Charge. FD-1028

Removing the existing unserviceable locks and S&F locks of appropriate size 6 levers with duplicate keys chromium plated Make Godrej or equivalent as suitable in book case with suitable fixing arrangement all as directed by Engr in Charge and shown on drgs for book case steel glazed. FD-1028

Removing existing unserviceable locks and supply and fixing new one with duplicate keys as existing all as specified and shown on drg. (Make - Godrej or Lico or as approved by GE). FD- 1002

Removing of existing unsv drawer from table office officer steel and supply & fixing of new drawer made of 1mm thick CRC sheet all as per drg and specified by Engr- in-Charge. The new drawer should be painted with two coat of synthetic enamel paint over a coat of red oxide and colour approved by GE. FD- 1002

Replacement of unserviceable locks and supply and fixing new one with duplicate keys as existing all as specified and shown on drg. (Make - Godrej or Lico or as approved by GE). FD-1004, FD-307

Removing of existing unsv drawer from table office officer steel and supply & fixing of new drawer made of 1mm thick CRC sheet all as per drg and specified by Engr- in-Charge. The new drawer should be painted with two coat of synthetic enamel paint over a coat of red oxide and colour approved by GE. FD-1004, FD-307

Removing the existing unserviceable cane from Chair Verandah and recanning of chair verandah with best quality of Make Maharashtra/Swastik Industries of approved plastic cane 4mm wide as per trade pattern all as specified and directed by Engr-in-Charge FD-19 (M)

S&F new hard rubber shoes of appropriate size suitable to chair verandah all as specified and shown on drawing and as directed by Engr in Charge FD-19 (M)

Removing the existing plywood from bed hard steel and preparation of old painted steel surfaces and applying one coat of synthetic enamel paint colour as approved by Garrison Engineer on all external and internal surfaces and refix the plywood of under mentioned bed hard steel as specified and as directed by Engr-in-Charge. Note : New plywood rates will be paid seprately FD/E6/MAP/08

Supply only new plywood BWR Grade ISI marked of size 1980 mm x 900 mm with headless MS nut & bolt 6 mm dia 75 mm length with washer and directed by the Eng-in- charge FD/E6/MAP/08

Removing the existing unsv particle board of head rest for bed hard steel and supply & fixing of new prelaminated particle board of 18/19mm to head rest for bed hard steel as per drg and directed by Engr-in-Charge. FD/E6/MAP/08

Removing the existing unsv particle board of foot rest for bed hard steel and supply & fixing of new prelaminated particle board of 18/19mm to foot rest for bed hard steel as per drg and directed by Engr-in-Charge. FD/E6/MAP/08

S&F new hard rubber shoes of appropriate size suitable to beg hard steel all as specified and shown on drawing and as directed by Engr in Charge. FD/E6/MAP/08

Removing the existing plywood from charpoy MS and preparation of old painted steel surfaces and applying one coat of synthetic enamel paint colour as approved by Garrison Engineer on all external and internal surfaces and refix the plywood of under mentioned charpoy MS as specified and as directed by Engr-in-Charge. Note : New plywood rates will be paid seprately . FD/MAP-II/01

Supply only new plywood BWR Grade ISI marked of size 1980 mm x 900 mm with headless MS nut & bolt 6 mm dia 75 mm length with washer and directed by the Eng-in- charge. FD/MAP-II/01

S&F new hard rubber shoes of appropriate size suitable to charpoy MS with plywood top all as specified and shown on drawing and as directed by Engr in Charge. FD/MAP-II/01

Removing the existing unserviceable plywood from bed hard wooden Plywood top and upply & Fixing new plywood BWR Grade ISI marked of size 1980 mm x 900 mm rounded edges on four corner fixed with MS nut & bolt 6 mm dia 75 mm length with washer to bed hard wooden with plywood top and all as directed by the Engr-in- charge, FD- 246

Removing the existing unserviceable head board including legs from bed hard wooden Plywood top and supply & Fixing new head rest including leg to bed hard wooden with plywood top as per drg and all as directed by the Engr-in- charge. FD- 246

Removing the existing unserviceable foot board from bed hard wooden Plywood top and supply & Fixing new foot board including leg to bed hard wooden with plywood top as per drg and all as directed by the Engr-in- charge. FD- 246

Removing the existing unserviceable long rail from bed hard wooden Plywood top and upply & Fixing new long rail to bed hard wooden with plywood top as per drg and all as directed by the Engr-in- charge. FD- 246

Removing the existing unserviceable plywood from Charpoy GI pipe Plywood top S&F new plywood BWR Grade ISI marked of size 1980 mm x 900 mm rounded edges on four corner fixed with MS nut & bolt 6 mm dia 75 mm length with washer and directed by the Engr -in- charge, FD- 220

Removing the unserviceable/broken check nuts from GI charpoy & supply and fix 6mm thick GI Medium grade check nuts suitable for 32mm dia GI pipe all as specified and shown on drawings (Each check nut will be measured as single unit) FD- 220

Removing the unserviceable broken 3 way GI elbow from GI charpoy & S&F 32 MM dia GI medium grade 3 way elbow ISI marked all as specified and shown on drg and directed by Engr-in-Charge (Each Elbow GI shall be measured as single unit) FD- 220

Removing the existing unserviceable/broken long rail from GI charpoy and S&F new long rail of GI tubing medium grade 32 mm including cutting, threading and bringing the GI charpoy into the original shape as shown on drawing and directed by Engr-in-charge FD- 220 Make- Jindal/Suryapraksh/Zenith/Appolo

Making short rails obtained from item No 33.04 above and fixing all as shown at item No 33.04 above FD- 220

Making legs out of unserviceable long/short rails obtained from item 33.04 & 33.05 above including cutting, threading and fixing all as specified and directed FD- 220

Plate welding-supply and welding 3mm thick 45mm dia MS bottom plate for GI charpoy leg all as shown on drawing and as directed by Engr-in-Charge (each base plate will be measured as single unit). FD- 220

Clamp Welding -supply and welding flat Iron 25 mm x 33 mm mild steel clamps made to shape as shonw in drg shall be welded in GI charpoy leg all as shown on drawing and as directed by Engr-in-Charge (each clamp will be measured as single unit). FD- 220

Taking out old unsv seat from chair easy cushioned and Supply and Fixing new 75mm thick foam cushion of 32 Density shall be fixed on 12mm thick BWR plywood of seat. And new existing size and shape alongwith cover foam shall be upholsted with leatherised rexene of approved shade and texture of best quality as approved by Engr-in-Charge shall be provided.Make of foam shall be Kurlons/Sleep well. FD - 358

Taking out old unsv back rest from chair easy cushioned and supply and fixing new 50mm thick foam cushion of 32 density shall be fixed on 12mm thick BWR plywood of back rest. And new existing size and shape alongwith cover foam shall be upholsted with leatherised rexene of approved shade and texture of best quality as approved by Engr-in-Charge shall be provided. Make of foam shall be Kurlons/Sleep well. FD - 358

Taking out old unsv arms from chair easy cushioned and S&F new arms as per existing size and shape complete all as specified and as directed by Engr-in-Charge. FD - 358

S&F new legs FD - 358

S&F new short & side rails FD - 358

S&F new long rails FD - 358

S&F new short stiffeners FD - 358

S&F new long stifferners FD - 358

S&F new rubber/PVE shoes provided to the bottom of legs FD - 358

Removing the existing unserviceable Seat from Chair computer revolving and S&F of new Seat (12 mm thick hot pressed ply wood, upholstered with fabric and moulded polyurethane foam and PVC lipping all around to them in all respect overall size 510x470x60mm. Make : Godrej or equivalent ) to Chair computer revolving all as shown on drg and as directed by Engr-in-Charge. FD/E6/MAP/01

Removing the existing unserviceable Back from Chair computer revolving and S&F of new Back (12 mm thick hot pressed ply wood, upholstered with fabric and moulded polyurethane foam. The back form shall be designed with contour lumber support for extra comfort with PVC lipping all around to them in all respect overall size 510x470x60mm. Make : Godrej or equivalent) to Chair computer revolvingall as shown on drg and as directed by Engr-in-Charge. FD/E6/MAP/01

Plate welding-supply and welding 3mm thick 45mm dia MS bottom plate to chair computer all as shown on drawing and as directed by Engr-in-Charge FD/E6/MAP/01

Removing the existing unserviceable Arms from Chair computer revolving and S&F of new arms to Chair computer revolving all as shown on drg and as directed by Engr-in-Charge. FD/E6/MAP/01

Removing the existing unserviceable fibre stem base from Chair computer revolving and S&F of new fibre base stem to Chair computer revolving all as shown on drg and as directed by Engr-in-Charge. FD/E6/MAP/01

Removing the existing unserviceable Bottrom gas lift hydraulic from Chair computer revolving and S&F of new Bottrom gas lift hydraulic to Chair computer revolving all as shown on drg and as directed by Engr-in-Charge. FD/E6/MAP/01

Removing the existing unsv soft board from Notice board and supply & fixing of new soft board of suitable size of notice board size 1830x1220mm. All as per drg and directed by Engr-in-charge. FD- 99

Removing the existing unsv soft board from Notice board and supply & fixing of new soft board of suitable size of notice board size 2440x1220mm. All as per drg and directed by Engr-in-charge. FD- 99

Preparation of old painted steel surfaces ie. de-rusting, filling putty, denting and applying two coats of synthetic enamel paint as approved by Garrison Engineer on all external and internal surfaces ofform w/o back seel as specified and rest as directed by Engr-in-Charge. FD-77(M) & 1027

Removing the existing unsv seat from form without back and supply & fixing of new wooden seat made of teak woodin one piece of size 1525mm long 255mm wide and 25mm thick wooden planks bolted to frame with 3mm dia GI nut bolt and washer to form w/o back steel including preparing wooden surface and polish with french polish. Rest all as per drg and directed by Engr-in-charge. FD-77(M) & 1027

Preparation of old painted steel surfaces ie. de-rusting, filling putty, denting and applying two coats of synthetic enamel paint as approved by Garrison Engineer on all external and internal surfaces of form with back steel 6' and rest as specified and as directed by Engr-in-Charge. FD-78(M), 1027, HFD-20252

Removing the existing unsv seat from form with back steel 6' and supply & fixing of new wooden seat made of teak woodin one piece of size 1525mm long 255mm wide and 25mm thick wooden planks bolted to frame with 3mm dia GI nut bolt and washer to form with back steel 6.0' including preparing wooden surface and polish with french ploish.Est all as per drg and directed by Engr-in-charge. FD-78(M), 1027, HFD-20252

Removing the existing unsv back from form with back steel 6' and supply & fixing of new back of wooden planks of suitable size of form w/o back steel including preparing wooden surface and polish with french polish.Rest all as per drg and directed by Engr-in-charge. FD-78(M), 1027, HFD-20252

MAURYA CONSTRUCTIONS (BID ID -3075947)

KAILASH KUMAR LADHA (BID ID -3076482)