Erode District Construction of Conference Hall at RIRD New Building Campus in Bhavanisagar Block under Centre of Excellence Scheme 2025-26

Amount

Earth work excavation for foundation in all clauses of soils and sub soils to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring strutting and boiling out water whenever necessary etc. complete

Supplying and filling in basement with filling M.Sand in layer of not more than 15 cm thick well rammed etc., complete.

Supplying and filling of conveyed earth with a lead of 1Km for basement filling to the standard Specifications etc.,complete.

Cement concrete 1:4:8 mix ( one cement four sand and eight aggregate)using 40mm gauge hand broken granite tone jelly for foundation including dewatering if found ecessary and laid in layers of not more than 15 cm thick and compacted,etc., complete

For Foundation and Basement

Brick work in Cement Mortar 1:5 mix, using best quality Fly ash bricks of size 23x11x7cm including curing,Finishing etc,complete complying with standard specification.

(A) For Foundation and Basement

(B) For Super structure in GF

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton.

(A) Below Ground Level

(B) Column

(C) Sunshade

(D) Roof slab

Supplying fabricating and placing in position of ribbed steel rods for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors etc., complete

RCC 1: 11/2 :3 mix using 20 mm ISS HBG metal for RCC items of work excluding centering, shuttering and Cost of reinforcement grill including curing, finishing, fixing fan clamps and fixtures etc complete

For Foundation and Basement

For Super structure in GF

Supplying and applying two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1St coat of putty mixied with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete instructed by the departmental officers

Special ceiling plastering and finishing the exposed surface with Cement Mortar 1:3 (One Cement and Three M.Sand) 10mm thick of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., complying with standard specification

Plastering with cm 1:5 mix( one cement and five sand ) to 12 mm thick including cost and conveyance of all materials in all floors etc.,as directed by departmental officers etc, complete complying with standard specifications.

Distembering two coats using oil bound distember including cost and conveyance of all materials to site and labour charges etc. Complete

Exterier Emulsion Painting two coats using shell lime including cost and conveyance of all materials to site and all labour charges etc comoplete

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supplying and fixing of solid PVC door shutter with frame using 19 gauge a9mm MS square tubes for styles and outer frames 15mm MS square tubes for top lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall regidly fixed in position including necessary furniture and fitting.The overall size of styles shall be 50x30mm.The overall size of top rail,lock rail and bottom rail shall be 75x30mm.The overall size of frames shall be 50x45mm with suitable rebate for housing the shutter.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Suplying and fixing M.S Grill for Window & Ventilators including cost of materials and labour charges for cutting to required sizes, fabricating, welding and transporting at site of work and including the cost of one coat red oxide primer etc., complte complying as directed by the departmental officers.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone M.Sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone M.Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Granolithic floor finishing with cement concrete 1:2:4mix using 10 to12mm chips including cost and conveyance of all materials to site and all ladour charges etc. Complete A) 25 mm thick

Paving the floor with best quality of Stain Free Nano Polish Vitrified Tiles 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone M.Sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification

Flooring with Design Anti sik tiles laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification.

Dadooing the walls with glazed tilesof size300x200x6mm including cost and conveyance of all materials to site and all ladour charges etc

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone M.Sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and fixing of 110mm dia PVC Rain water down fall pipes with necessary bend, shoe, wooden plug, clamp, nails etc., complete.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification.

Supplying and fixing in position best quality and approved make Indian made white glazed earthern ware wash hand basin of size 550x400mm white color of approved brand and quality including cost of cast iron brakets 15mm.dia brass CP pillar tap 30mm.dia "B" class GI waste pipe 30mm.dia CP brass waste coupling with rubber plug and chain, 50mm.brass nipple 15mm.dia nylon connection including fixing of wash basin in the wall in position with a pair of CI brakets with TW plugs and screws, rubber washers, white led and giving necessary water supply connection and painting the brakets with a two coat of painting over a priming coat of anti corrosive paint including testing for leakages etc., complete complying with standard specifications

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications

Supply and delivery and fixing of 1000 ltr. HDPE tank as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc., TWAD SOR - WD-M1418

Supplying and Fixing of M.S Angles of size 50x50x6mm for Purlin including cost and cutting, fixing charges etc, SOR(W-0166,M-0187) including Ramp Hand Rails

Supplying and fixing of Galvalium sheet for head room roof with necessary adjustable ridges seater on 'U' or 'J' bolts

ELECTRIFICATION

Wiring with 2x1.5(22/0.30)sqmm pvc unsheathed SC Copper conductor of 1100Vgrade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with150x100x113mm TW switch box for 5A-3pin non inetrlocking CS plug including pin top with painting of suitable colour with continous earth wire connection of 14SWGTC wire for Concelled PVC plug point.( SD No.38 )

Wiring with 2x4(56/0.30)sqmm pvc unsheathed SC Copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with 150x100x63mm TW switch box for 15A-3pin non inetrlocking CS plug including pin top with painting of suitable colour with continous earth wire connection of 14SWG TC wire for Concelled PVC power plug point.( SD No.40 )

Supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. (SD No.448) False Ceiling mounted Light

Supplying and fixing of single box type 4'-40W flourescent tube fitting with copper choke and condunser with TW round block on wall or ceiling with flourescent tube with PVC unsheathed copper leads from terminals to fitting of tube light. (SD No. 89) Tube light

Supplying and fixing of 1200mm (48") sweep AC ceiling Fan complete with stepped eloctronic 300W regulator with 1m down rod with fan clamp with side plates and cross arm of size 450mm (18") (SD No.107)

Supply and fixing of 30W LED street light fitting with LED (Higher end) with 25 mm dia. GI pipe (class B) with 1 no. 25 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting. (SD No:454)

Wiring with 2x1.5(22/0.30)sqmm pvc unsheathed SC Copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box with 5A F.T switch in flush with wall covered with hylem sheet of 3mm thick with painting of suitable colour with continious earth wire connection of 14SWG wire for Concelled light point(SD No.24)

Supplying and fixing of 300mm SL bracket with fancy glass shade and 40W bulb(SD.No.81)

Supply and fixing of 63A TPNMC switch on suitable angle iron frame work with MS cable entry boxes with PWD earthing .(SD.No.149)

Supply and run of 4 of 6 sq.mm (84/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V on 7/20 GI bearer wire for service connection mains SD no.68

Supply and run of 4 of 6 sq.mm (84/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in 25mm dia GI pipe (Class 'B') suitably bent at both ends with necessary angle iron upright and end supports for mains SD no.73

Supply and fixng of TNEB meter board suitable for 3phase 63A service connection made up of suitable angle iron frame work of size 2feetx1-1/2feet using angle iron of size 1-1/2"x1-1/2"x1/4" rigidly fixed on wall covered with hylem sheet of size 2feetx1/2feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3Nos. 63A fuse units (500V), 1No. neutral link, copper earth flat of size 1"x1/4" with inter connection of EB meter to fuse units by 16Sq.mm PVC insulated copper wire with 1No 63Amp 30MAF our Pole RCD/RCCB (Higher End) with suitable necessary connection with earth connection complete. SD no.131

SUPPLY & INSTALLATION OF AIR-CONDITIONER WITH COPPER COIL - 2.0 TR Split Type AC Unit - 5 Star Rated) (PWD SOR M-1985)

Supplying, fabricating, erecting and fixing Hilux (or) Equivalent Board False Ceiling upto a ceiling height of 4.5m from floor level (SOR M-0619) Using Perforated Sheets (10mm thick)

50mm dia PVC Pipe

25mm dia PVC Pipe

Earth work Excavation lead of 10 mtr and lift of 2 mtr for Ordinary soil etc.

PVC Pipe portion

Lowering PVC/ DWSC rigid pipes and specials to trench and laying to proper grade and alignment, jointing with PVC couplers with cement paste.

PVC Pipe

Refilling the trench with excavated soil etc.

PVC Pipe portion

Provision for Rainwater harvesting pit and leach pit (2 Nos)

RCC Ring 900mm dia.

GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for overall quoted amount (for Construction) above this row in column "BB" for all works in this package}

YES PEE ASSOCIATES (BID ID -1549259)