SPECIAL REPAIR TO BUILDING NO P-06 AND T-59 AT DAMANA UNDER GE JAMMU

Amount

B/R Portion: - Taking down chowkats or frames with shutter w/o taking off shutter from the frame n.exc 1.5 sqm each incl cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and directed.

Taking down chowkats or frames with shutter w/o taking off shutter from the frame exc 1.5 sqm but n.exc 4 sqm each incl cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving's n.exc 15 cm thickness (below or above ground level) and removing unserviceable material exc 100 mtr complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position complete all as specified and as directed by the Engineer-in-charge.

Demolition of brick masonry built in cement mortar including all quions, arches, pillars etc complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls or from concrete surface incl racking out joints hacking for key scrubbing with water etc complete all as specified and directed.

Dismantling floors hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed.

Dismantling of PVC 110mm drain pipes jointed in cement mortar and taking out of trenches if required complete all as specified and directed.

Dismantling of PVC 75 mm drain pipes jointed in cement mortar and taking out of trenches if required complete all as specified and directed.

Taking down GI tubing of 15 mm dia and connection and incl cleaning for refixing or removal complete all as specified and directed.

Taking down GI tubing of 20 mm dia and connection and incl cleaning for refixing or removal complete all as specified and directed.

Dismantling/disconnecting/demolition of water storage tank of any type or description PVC exc 250 and n.exc 500 Ltrs capacity and removing from site or refixing in position complete all as specified and directed.

Taking out the roots of trees/ shrubs of any girth from the surface of bldgs and making good the damaged portion to match with the existing surface in CM (1:3) or with PCC (1:2:4) or Brick work in CM 1:4 and finally finishing the surfaces to match with the existing surfaces complete all as specified and directed.

M&L for brick work of old size sub class ‘B’ bricks straight or curved on plan exceeding 6mtr mean radius built in Cement Mortar 1:6 complete all as specified and directed.

Description all as per Ser item No 15 here-in-before but except bricks complete all as specified and directed.

S&F Pressed steel frames for door (Factory made) out of 1.25 mm thick black MS sheet, with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc. complete, size of frame 105x60mm incl bottom of each chowkat to be welded with 2 Nos 25x25x3 mm thick flat iron projecting 10 cm on either side and back fill to chowkats with PCC 1:3:6 type C0 using 12.5 mm graded crushed stone aggregate including one shop coat of red oxide primer complete all as specified and directed. Note: PCC 1:3:6 type C-O as in backfill will be paid separately.

M&L cement concrete 1:3:6 type C-O using 12.5mm graded stone aggregate as in backfill of pressed steel door frames complete all as specified and as directed by the Engineer-in-charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying and fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete, all as specified and directed by Engr-in-Charge.

S&F for 35 mm thick 2nd class hard wood half glazed and Skelton shutters open rebated and prepared to receive glass/wire gauge etc. without sash bar but with lock rail edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass/wire mesh etc sizes of member as per clause 8.20(a) of SSR part -I for door shutter complete all as specified and directed.

M&L for 18/19 mm thick prelaminated particle board interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work as in cupboard shutters/pelmet box and cupboard shelves including teak wood beading all around all as specified & directed.

S&F box type steel windows/Ventilator (factory made) outer frame made out ERW tube 'P' section 65X45X25 mm and shutter of ERW tube 'P' section 50mmX35mmX20mm openable (double shutter) with glazed shutter on extrernal side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 nos on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler /AC window complete all as specified and shown on drgs No CEPZTD-324/07 Sh 1/3 to 3/3 Note:- The quoted rate a shall also include (i). One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrte surface (ii) 4 nos MS steel lugs made of 20X5 mm Iron flat 200 mm long iii)10 mm Sq Bar grill/guard bar design as per drawing (iv) PCC block for embedding lugs

M&L for PCC 1:2:4 type B1 using (20 mm graded aggregate) as in blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating, all as specified and directed. Note : From work required for these item included in the unit rate of this item.

Hacking out old broken glass of any thickness, size, quality or description from the wooden/ steel frames glazing with puttyor fixed with wooden beads complete all as specified and directed.

S&F 3.0 mm thick sheet glass ordinary quality glazing with steel pins, oil putty to steel windows and beads nails etc. to wooden surfaces as in square n exc 0.50 sqm in each pane, complete all as specified and directed.

S&F 3.0 mm thick figured glass, pin headed/frosted head type and glazing with oil putty in square n.exc 0.50 sqm in each pane complete all as specified and directed.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks or galvanized with staples including one coat of red oxide primer complete all as specified and directed.

S&F Mild Steel butt hinges 100mm long medium weight cold rolled complete all as specified and directed.

S&F 100 mm long hasp and staple, aluminium anodixed with bolt to hinge palte and fixed with screws complete all as specified and directed.

S&F Aluminium anodised barrel tower bolts of extruded section with 150 mm long bolt, all as specified .

S&FAluminium handle, cast type, anodised 150 mm long complete all as specified.

S&F in repairs 20 mm dia Ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ballscrewed for iron pipe and fixed (min wt 210 gram), screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F small fittings 2nd class hardwood such as brackets of any types latch and hings blocks shaped door and window stops and the like, not exc 200 cu cm each complete all as specified and directed.

S&F Aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

M&L Glazed ceramic coloured tiles 450x350x7 mm thick on vertical surface as in skirting,dado set and jointed with neat cement slurry and pointed in white or coloured cement to match with the surface over and including 10 mm thick screed in CM 1:4 complete all as specified and directed.

M&L for non skid ceramic tiles 7 to 8 mm thick (Square/rectangulament) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors over 15 mm thick screed in CM 1:6 set and jointed in neat cement slurry and pointed in white/coloured cement with pigment to match complete all as specified and directed.

M&L for non skid ceramic tiles 7 to 8 mm thick (Square/rectangulament) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors over 15 mm thick screed in CM 1:6 set and jointed in neat cement slurry and pointed in white/coloured cement with pigment to match complete all as specified and directed.

M&L for Green marble 18 to 20 mm thick (table rubbed and polished ) in steps jambs, pillars, window cill, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick screed in CM 1:6 set and jointed in neat cement slurry and pointed in white/coloured cement with pigment to match complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25 mm thick laid over cement screed base 20mm thick in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting as required, rubbing and polishing to granite finish complete all as specified and directed.

M&L for machine cut kota stone slab 20-25 mm thick as in riser of steps, skirting, dado and pillar laid over cement screed bed of 15mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting as required, rubbing and polishing to granite finish complete all as specified and directed.

M&L for Rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surface fininished even and smooth without using extra cement including mixing of integral water proofing compound in the proportion as per manufacturers instructions complete all as specified and directed ( Note :- water proofing compound will be paid separately under respective item).

M&L for rendering 10 mm thick cement plaster 1:6 on other than fair faces of brick work or concrete surfaces and to be finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick cement plaster 1:3 on fair faces of concrete surfaces as in ceiling, chajja, shelves etc. finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick cement plaster 1:3 on other then fair faces of concrete surfaces as on facia of roof slab, chajja, shelves etc. finished even and smooth without using extra cement complete all as specified and directed. (incl all necessary scaffolding, lifting arrangment for three story building on external surfaces).

S&F PVC (SWR) P trap 110/110 mm bore complete all as specified and directed.

S&F PVC SWR pipes 110 mm bore single socketed in any length with rubber joint fixed to wall or laid in trenches or in floor with steel clamps complete all as specified and directed.

S&F PVC SWR pipes 75 mm bore single socketed in any length with rubber joint fixed to wall or laid in trenches or in floor with steel clamps complete all as specified and directed.

S&F PVC SWR bends of 110 mm bore complete all as specified and directed.

S&F PVC SWR bends of 75 mm bore complete all as specified and directed.

S&F PVC (SWR) junction double (double T) equal or unequal provided with access door of 110 mm dia complete all as specified and directed.

S&F PVC (SWR) junction single (single T) equal or unequal provided with access door of 75 mm dia complete all as specified and directed.

S&F PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia complete all as specified and directed.

S&F PVC (SWR) vent cowl 75 mm bore complete all as specified and directed.

S&F PVC (SWR) WC connector with lip ring 110 mm complete all as specified and directed.

S&F in repair WC Orissa pattern white with integral foot rest 580 x 440 mm including PCC bedding 1:2:4 and making good disturbed floor connecting to trap and flush pipe complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 Ltr capacity white with inlet ball value, float valve and handle inc brackets, PVC flush pipe complete all as specified and directed.

S&F PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipes of 15 mm bore complete all as specified and directed.

S&F in repairs Vitreous china wash hand basin white ,flat back of size 450x300mm including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed by Engr-in-charge.

S & F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F in repair tubular towel rail, 20mm dia, D type, 60cm long between flanges aluminium anodised, fixed with rawl plugs complete all as specified and directed.

S&F in repair chromium plated Bib tap with crutch or butterfly handle, fancy type screwed for iron pipe, suitable for 15 mm bore complete all as specified and directed.

S&F in repair stop valve/angle valve cast copper chromium plated screwed down high pressure with capstan head suitable for 15 mm bore, screwed both ends for iron pipe complete all as specified and directed.

S&F in repair brass chromium plated shower rose 125 mm size swivel type with connecting rod 15 mm bore complete all as specified and directed.

S&F in repair stop valve cast copper chromium plated concealed type screwed down high pressure with capstan head suitable for 15 mm bore complete all as specified and directed.

S&F stainless steel gratings of outer frame dia 150 mm open able type incl all necessary fitting such as hinges including embedding in tiles with white cement complete all as specified and directed.

S&F for curtain rails mild steel chromium plated with fixing brackets etc complete all as specified and directed.

S&F 15 mm dia galvanised pipe medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F 20 mm dia galvanised pipe medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F 40 mm dia galvanised spout pipe medium grade for with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Fixing only 15 mm dia old galvanised pipes incl new fittings where necessary fixed complete to wall and ceiling or laid in floor complete all as specified and directed.

Fixing only 20 mm dia old galvanised pipes incl new fittings where necessary fixed complete to wall and ceiling or laid in floor complete all as specified and directed.

Cutting chases for concealed water tubing or concealed conduit & making good in CM 1:3 of grith exc 10 cm and n.exc 20 cm in brick wall complete all as specified and directed.

M&L 75 mm thick PCC type C2 1:3:6 (40mm graded aggregate) as in Plinth protection filled with mastic filling and 10 mm wide joints between the walls and plinth protectin shall be filled with mastic filling complete all as specified and directed.

S&F rotational moulded polythylene water storage tank with float valve, plastic lid cover, double layered, cylindrical verticl with closed top hoisted and fixed in position of capacity 500 Ltr incl making connections complete all as specified and directed.

S&F in repair stop valve 20 mm dia cast copper alloy, secrewed down high pressure with crutch or butterfly handle secrewed both ends for iron pipe and fixed complete all as specified and directed.

Applying one coat of synthetic enamel paint tint over old painted steel surfaces over 10 cm in width or girth including preparation of old surfaces of steel complete all as specified and directed.

M&L for two coat of synthetic enamel paint tint after preparation of new surfaces of steel of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint complete all as specified and directed.

M&L for preparation of old wood or wood based surface and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of new wood or wood based surface and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

M&L for two coats of oil bound distemper of wall to newly plastered surfaces over chalk whitening including preparation of surfaces complete all as specified and directed

M&L for one coat of oil bound distemper of wall to old plastered surfaces including preparation of surfaces complete all as specified and directed

Preparation of old plastered surfaces including filling of small holes etc and applying two coat of white wash on ceiling surface complete all as specified and directed.

Preparation of surfaces new plastered surfaces & applying three coat of white wash on ceiling complete all as specified and directed.

M&L for two coats of cement base paint to newly plastered surfaces including preparation of surfaces and priming plastered surfaces with alkali resistant priming paint complete all as specified and directed

M&L for one coat of cement base paint to old plastered surfaces including preparation of surfaces complete all as specified and directed

S&F in repair Stainless steel kitchen sink with drainage board made of stainless steel of 1 mm thick sheet including plugs, washers and pvc waste pipe of 40 mm dia. Fixing with complete on appropiate size of cantilever brackets of MS angle or GI pipe 15 mm dia with proper arrangment to hold and fitting of sink complete all as specified and directed at site and connecting union to pipe. The overall size of sink 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed

S&F in repair Stainless steel grade 430, glossy finish, wall hanging plate rack inclusive of spoon hanger, made out of 1mm thick sheet of size 750 x 600 x 250 mm having partition as per sample kept in AGE B/R office and fixed with steel fasteners or steel screwed complete all as specified and directed

M&L cement concrete 50mm thick in 1:3:6 type C-2 (40 mm graded aggregate) as in flooring finished even & rough complete all as specified and directed

M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006of 60 mm thickness, M-35 Grade with grey cement and no pigment complete all as specified and directed

M&L for preparation of surface, the surface must be sound & free from dirt, dust & loose particles, thoroughly wire brush the surface & clean the dust, wash the surface with water. Any damage surface must be repaired by using polymer modified repair mortar with Dr. Fixit Pidicrete URP. Clean the surface, saturated with water and remove the excess water if any and bring to touch dry state. Applying the first coat of mixed @ 0.75 sqm/kg, 1mm thick for 2 coats) Dr Fixit Pidifin 2K on the prepared surafce & allow to dry for 4 to 6 hours. Prepare another batch of Dr Fixit Pidifin 2K and apply 2nd coat in direction 90 degree to first coat. Overlay protected screed using cement sand 1:3 along with Dr Fixit LW+ complete all as specified and as directed.

M&L cement concrete type E-2 1:5:10 (40 mm graded aggregate) as in sunken portion complete all as specified to receive floor toping as specified after carrying out the required tests of water proofing

Removing existing treatment from roof surfaces such as tiling, tarfelt, fungus,moss,dust etc.,cleaning the surface of all foreign material by wire brushing and dusting and racking out RCC slab complete all as specified and directed and removing the debries outside defence land.

M&L for Rendering 20 mm thick in CM 1:4 on fair face of brick work or concrete surfaces finished even and smooth without using extra cement up including mixing liquid water proofing compound complete all as specified and directed(Note- liquid water proofing compound shall be measured and paid separately)

Supply only liquid water proofing compound.

Roof Treatment with the folowing specification :- (a) Applying evenly one coat of Bituminous Primer conforming to IS 3384-1986, @ 0. 3 ltrs per sqm over cleaned plastered surface. (b) Applying evenly one coat of blown Hot Bitument of Grade 85/25 @ 1.2 Kg per sqm on primed surfaces. (c) Applying a layer of APP based Polymeric Memberance 3mm thick (Minimum) weighting 3.5 Kg per sqm (reinforced) with polyster Non woven fabric weighing not less than 160 gms per sqm by torch application. The overlap shall be minimum 100 mm on traverce direction and 75 mm on longitudinal direction and sealing overlap by torch application. (d) Applying evenly one coat of Aluminium paint @ 0 .10 Ltr per sqm over the APP based polymeric Membrane.

M&L for Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc and n.exc 10 Sqm on plan and n. exc 1.5 mtr in depth and getting out in any type of soil complete all as specified and directed

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed

Removing excavated material n exc 50m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and directed

M&L 150 mm bore/Inner Dia. Double wall corrugated HDPE Pipes (SN8) with integral socket and necessary fittings, laid in trenches, including jointed and overlaping of pipe complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate as in foundation,filling in and mass concrete complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded cruched stone aggregate) as in benching, coping etc including necessary form work complete all as specified and directed

M&L for Pre-cast RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in manhole cover slab fixed in position including necessary form work and set in CM 1:6 complete all as specified and directed

M&L mild steel TMT 10mm dia and over cut to length, bent to shape, required including cranking, bending, spirally for hopping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in surface channels and drains etc complete all as specified and directed

M&L for chequered cement concrete coloured tiles 30cm x 30cm x 25 mm thick, polymer moulded set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment over and including screed bed and bedding layer of mortar 20mm thick in cement plaster (1:6) for laying floor finishes.as per design/pattern approved complete all as specified and directed by Engr-in-Charge.

Dismanting asbestos cement (corrugated or semicorrugated etc) sheets in roof covering complete all as specified and directed

Dismantling timber scantling 40 sq cm and over in section framed work of any description complete all as specified and directed

Dismantling boarding any description fixed in any position with nail including GI frame work complete all as specified and directed

M&L half brick thick brick work with sub class "B" bricks straigth or curved on plan exc 6m mean radius built in CM (1:4) complete all as specified and directed

M&L spreading leveling in layers n exc. 25cm thick and well ramming complete all as specified and directed

M&L cement concrete type C-2(1:3:6), 100mm thick in sub base complete all as specified and directed

M&L broken brick Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F for structural steel works of Fe 410W (Gde E 250) quality A, as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. including painted one shop coat of zinc chromate/red oxide primer paint (including preparation of surface) before fabrication complete all as specified and directed

S&F 4mm thick of size 605X605 mm ,White pre-premiered, self embossed, Reinforced Designer Board for false ceiling Conforming to IS-14862 and ISO-8336:1993. As per specification under mention: (i)GI section frame work (POWDER COATED) for white, pre-premiered, self embossed, reinforced designer board consisting of perimeter wall angle 19mmX19mmX0.45mm, cross 'Tee' 28.6mm (web)X 24mm flange .33mm thick powdered coated main tee 38(Web) X24mm flange 0.33mm thick. wall angle screwed fixed to brick wall/partition wall/concrete/RCC with the help of nylon sleeves and screws @ 610 mm C/C , Then suspending GI main 'Tee' in both directions by means of hangers with alignment @ 1220mm C/C to soffits. To from grid of 610X610mm cross Tee shall be provided @ 610mm C/C in both directions. Suitable provisions shall be made for fixing the recessed/surface mounting light fittings if any, complete all as specified and directed by Engr-in-Charge.

S&F powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed

S&F powder coated anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 No in each door hinges, anodised aluminium snap beading screws etc complete all as specified and directed.

S & F powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including anodised aluminium safety grill and necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed

S&F 5.50 mm thick sheet glass fixing for Aluminium doors and windows including 25 micron reflective type sun control film complete all as specified and directed.

S&F Aluminium (extruded section) body door closer hydraullicaly regulated designation No 2, universal type suitable for door shutters of 701 to 850mm in width and of weight between 36 and 60kg and fixed in repairs complete all as specified and directed.

M&L Granite 20mm thick (tabled rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar 1:4 including pointing in colour cement 1;2 using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screedbed in cm1:4 edges of slab to be rounded from all sides (including cutting, wastage and polishing) complete all as specified and directed.

S&F vitreous China water closet one piece with quiet close, slim seat cover in white S- Trap, 305 mm complete all as specified and directed. Make: Kohler Cat Part No K-77739T-SL-0 or its equivalent in Kohler

S&F PVC (SWR) curved pipe S trap 110/110 mm bore complete all as specified and directed. Make : Kohler Cat Part No K-1066987 or its equivalent in Kohler

S&F Health faucet polished in chrome complete all as specified and directed. Make Kohler Cat Part No K-98100IN-CPor its equivalent in Kohler

S&F PVC (SWR) reducer of 110 mm dia complete all as specified and directed.

S&F 560 x 864 mm rectangular mirror-matte black complete all as specified and directed.Make: Kohler Cat Part No. K-26052-BLL or its equivalent in Kohler

S&F Vitreous china Bardon urinal with rear inlet 0.5l with accuflush in white,white including waste pipe 32mm dia GI pipe, grating and brass union for discharge pipe complete including providing and fixing plug bedding urinal against wall in cement mortar 1:2 securing urinal to plug with and including 60mm long brass screw pointing around urinal back in cement etc complete all as specified and directed by Engr-in-charge. Make: Kohler Cat Part No K-4991-ER-0 or its equivalent in Kohler

S&F Vitreous china urinal partition white of size 310x700 mm complete all as specified and directed.

S&F 413 mm square vessel basin with single faucet hole in white complete all as specified and directed.Make Kohler Cat Part No K-75374IN-1-0 or its equivalent in Kohler

S&F bottle trap 350mm for square vessel basin complete all as specified and directed.Make Kohler Cat Part No K-75823IN-BN or its equivalent in Kohler

S&F single control tall basin faucet with drain in polished chrome, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of bore 15 mm, complete all as specified and directed Make: Kohler Cat Part No 29929IN-4-CP or its equivalent in Kohler

S&F towel ring of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats complete all as specified and directed

S&F in repair Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 1000 ltr complete all as specified and directed

S&F 15 mm bore Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed

S&F 20 mm bore Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed

S&F grating doom 100mm dia of PTMT (minimum weight 25 gms) complete all as specified and directed

S&F PVC cupboard shutter 20 mm thick decorative pre-laminated complete water proof, termite proof and fire proof complete all as specified and directed

E/M Portion: -Taking down old unsv copper/aluminium point wiring concealed / batten (light, fan, socket or power) complete, including fixture and fittings such as switches,sockets, ceiling roses,bell push,bell electric,lamp holder,bulk head fitting, pendants, regulators, sockets, light fitting and any type switch board wooden/iron,round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed

M&L for point wiring for one light/fan/call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into new concealed PVC rigid/steel conduit and into existing CI/pressed steel sunken/ terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified and directed Note : (a) wiring shall be done by using proper colour coding (b) Earth wire shall be of green colour (c) On RCC roof/celing PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engr-in-Charge.

Description all as per serial item No 143 here in above but One 5 pin socket outlet 5 amps on the same board complete all as specified and directed

Description all as per serial item No 143 here in above but One 5 pin socket outlet, 5amps, independent complete all as specified and directed

Description all as per serial item No 143 here in above but for one 5 pin socket outlet 15 Amps on Independent board with cables 2.5 sqmm size complete all as specified and directed

S&F in replacement for switch piano, flush type single pole one way 5Amp, 240 volts complete all as specified and directed

S&F in replacement stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified and directed

S&F in replacement Switch socket outlet combined 5 pin 5 amp flush type , 240 volts complete all as specified and directed

S&F in replacement Switch socket outlet combined 2 in 1 , 3 pin 5 amp and 15 amp flush type , 240 volts complete all as specified and directed

M& L in replacement for Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed

M& L in replacement Self ballast LED retrofit Lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and directed

S&F in repair Ceiling Rose 3 terminal surface type complete all as specified and directed

S&F in replacement LED lights fitting 1x 20W, 220V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.95 , 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. (4' ft long ) with LED rod 20 watt, 230 Volts 50 Hz. complete all as specified and directed

M&L for replacement distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and directed

S&F in replacement 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 40 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed

Supply and fixing in repair SPN 40 to 63 Amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed

Dismantling and taking down old unsv street/security lights and Material and labour for new LED street light fittings of 30 watt system wattage and high preesure die cast aluminium housing with sealed toughened glass cover, TIP 66 protection suitable for pole mounting SMD led array with lense, cool white 6500 K, LED efficacy >120 lm/W and system efficacy 110 lm/W , 240 Volts AC, 50 Hz, CRI>70% operating voltage range 160 V-270 V, Power factor> 0.95, working temperature range -20ºC to 60ºC,built in surge protection more than 10kV with facility of power supply shall be removed without removing light fitting from pole incl make proper connection complete including cutting , welding , drilling holes, nut bolts, washer complete all as specified and directed by Engineer-in-charge.

M&L in replacement for Sub main wiring with proper colour coding , insulated , unsheathed , multistranded ,copper conductor FRLS, cable of 2 run 6 Sqrmm for phase and neutral and one run of 6.0 Sqrmm for earth wire unsheathed , multistranded , copper conductor FRLS, drawn through the new rigid PVC concealed conduit fixed on wall complete all as specified and directed. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length. Note : Wiring shall be done in proper colour coding.

M&L in repair for Earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with suitable handle made of round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube flor watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and directed

Supply and fixing in replacement plug top 15 Amps complete all as specified and directed.

Supply and fixing in repair ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed

Supply and fixing in repair TPN DB current carrying capacity 125 Amps suitable for accommodationg TPN miniature circuit breaker (MCB) 4 Pole and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed

Supply and fixing in repair 415V 10KA 'B' curve TPN 40 to100 AMP miniature circuit breaker (MCB) 4 poles and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed

Disconnecting & taking out defective service cable any size and any type from roof, pole, pipe, floor, wall etc complete all as specified and directed

Supply and laying, connecting and testing XLPE underground cable insulated, and overall sheathed with aluminium conductor heavy duty 1100 volts grade 10 sqmm 2.0 core laid in trenches/ on poles/ road crossing or passing through existing/new pipe under road crossing, clamping on wall etc complete all as specified and directed Note: (i) Earth work, sand, bricks , removing, returning filling Aluminium thimbles/lugs will be paid separately. (ii) Cost of laying electrical cable through new/existing pipe under road, buildings, railway tracks, highways are incl in the quoted rates. (iii) All equipments , machinery or tools if required for laying electrical cable through new/existing pipes are provided by the contractor without any extra cost.

S&F in replacement of LED lights fitting 1x 10W, 220V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.95 , 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. (2' ft long ) with LED rod 10 watt, 230 Volts 50 Hz. complete all as specified and directed

M&L for replacement of distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 4 way 240 volts double door complete all as specified and directedby Engr-in-Charge. Note:- Distribution board and MCBs should be same make.

S&F in replacement of 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed

M&L for fixing of 4 Nos rawl plug of suitable size (4"-6") nuts & bolts for hanging of geysers on wall complete all as specified and directed

S&F in replacement of PVC connection of size 15 mm dia with PTMT nuts of length 450 mm long (hot series braded, threaded and cold series) complete all as specified and directed by Engr-in-Charge.

NOTE NO 1: - Samples of materials as approved will be kept in GE's sample room. NOTE NO 2: - All fittings and fixtures mentioned above will be fixed to the satisfaction of Engr-in-Charge and GE. NOTE NO 3: - Warranty certificate to the Engineer-in-Charge where ever applicable shall be submitted by the Contractor at the time of fittings.

Hare krishna engineering const.

STAR CONSTRUCTIONS

Bidder Name

Shri Karshni Builders

STAR CONSTRUCTIONS

Hare krishna engineering const.