SPL REPAIR TO BLDG NO P-64, P-64J AND P-65 IN THE AREA OF AGE B/R KALKA AND PROVN OF DRAIN BEHIND P-61 (COOK HOUSE TO NALA) OF 271 TRANSIT CAMP AT MIL STN KALKA UNDER GE JUTOGH

Amount

Taking down of cement plaster on walls of any description incl raking out of joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on brick or concrete surfaces finished even and smooth without using extra cement complete for internal surface complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick or concrete surfaces in CM 1:4 finished even and fair complete all as specified and directed.

M&L for rendering 5 mm thick on brick/concrete surfaces in CM 1:3 on ceiling and finishing the surface even and smooth complete all as specified and directed.

M&L for preparing new plastered surfaces of wall and applying three coat of white wash complete all as specified and directed.

M&L for preperation of new plastered surfaces wall applying two coats of cement base paint complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed.

M&L for complete removal of existing treatment from wall and applying two coats of cement base paint complete all as specified and directed.

M&L for preparation of old plastered surfaces and applying two coats of white wash on ceiling ccomplete all as specified and directed.

M&L for preparation of old plastered surfaces and applying two coats of white wash on wall complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n exc 15cm thick (below or above ground level) complete all as specified and directed.

Demolition of reinforced concrete of roofs, floors (other than ground floors) beams, staircases, lading, chhajas and similar suspended work complete all as specified and directed.

Use and waste of form work to chajjas and similar work for fair finish surfaces complete all as specified and directed.

M&L for RCC 1:1.5:3, type A-1, using 20mm graded crushed stone aggregate as in chajjas/ shelves/ slab etc complete all as specified and directed.

M&L for PCC 1:2:4, type B-1, Using 20mm graded crushed stone aggregate as in coping & benching kerbs in man holes including necessary form work complete all as specified and directed.

M&L for 40mm thick, PCC 1.2.4, type B-1, using 20mm graded crushed stone aggregate as in floor, surfaces finished even and smooth with using extra cement complete all as specified and directed.

M&L for 50mm thick, PCC 1.2.4, type B-1, using 20mm graded crushed stone aggregate as in alternate way floor, surfaces finished even and smooth without using extra cement complete all as specified and directed.

Supply only 38mm x 3mm glass dividing strips as in floors (fixing included in item of floor topping) complete all as specified and directed.

M &L for 75mm thick PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate finished even and smooth without using extra cement as in plinth protection complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed with cement mortar 1:6 complete all as specified and directed.

M&L Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in skirting/dado and riser to steps etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10mm thick backing coat with cement mortar 1:4 complete all as specified and directed.

Dismantling, floor, hearth or wall tiling/terrazo toping including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Glazed ceramic tiles on verticle surface such as skirting/ dado etc. 350X250X7mm/ 450X300X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match to coloured tiles fixed over and Incl 10 mm thick plastering in CM 1:4 complete all as specified and directed.

Excavation in trenches n.exc 1.50 m wide and n.exc 1.50 m deep as in foundation and footing and getting out in hard/dense soil complete all as specified and directed.

Dismentling of fencing wiremesh any type from TMT Bar/ Fencing post etc. complete all as specified and directed.

Demolition of brick work or built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc. 6 m mean radius, built in CM 1:6 complete all as specified and directed..

M&L for form work to sides of concrete foundations, footings, bases of columns, rafts and raft beams, sides and soffits (if any) of foundations and plinth beams and similar work rough finished surface complete all as specified and directed.

M&L for use and waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintels, cantilevers, shelves incl supports, overhangs etc also splays between floors and beams etc in rough finished flat surface of concrete complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in beam, cantilevers, lintel etc complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in column footing including raft footings, foundation, plinth beam, bases of columns etc complete all as specified and directed.

M&L for 25mm thick, louvers and jallies, casted with precast cement concrete 1:2:4, type B-0, using 12.5mm crushed stone aggregate set in CM 1:4 complete all as specified and directed.

Returning filling in soil including spreading leveling watering and well ramming in layers n.exc 25cm thick complete all as specified and directed.

Removal of surplus soil to a distance n.exc 50 m and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and directed.

Taking down chowkats or frames with shutter not exc 1.5 sqm (without taking off shutters from frames) and removing from site complete all as specified and directed.

Taking down chowkats or frames with shutter exc 1.5 sqm but n.exc 4.0 sqm (without taking off shutters from frames) and removing from site complete all as specified and directed.

Taking down shutters of size exc. 1sqm but n.exc 2 Sqm each of any description and refixing in same opening after necessary repair etc complete all as specified and directed.

Taking down shutters of any description of iron/wooden gate of size exc. 2sqm each and refixing in same opening after necessary repair etc complete all as specified and directed.

S&F pressed steel frames made of 1.25mm thick MS sheet of profile 125x60mm for door and window frames with double rebate including lock strike plate, shock absorbers, 20mm dia 60mm long MS conduit for housing of a drop bolt, butt hinges, hold fasts/lugs etc and treating of internal surfaces of chowkhats and hold fasts/lugs with a coat of coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified and directed.

S&F pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with double rebate including lock strike plate, shock absorbers, 20mm dia 60mm long MS conduit for housing of a drop bolt, butt hinges, hold fasts/lugs etc and treating of internal surfaces of chowkhats and hold fasts/lugs with a coat of coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

M&L for PCC 1:3:6, type C-1, using 20mm graded crushed stone aggregate as in filling back of pressed steel chowkhats complete all as specified and directed.

S & F 35mm thick factory made plain framed panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm venerred particle board with commercial veneering on both faces. The size of rail and style as per IS- 1003 (part -I) kiln seasoned and chemically pressure treated of 2nd class hardwood rails and style for doors incl one shop coat of pink primer complete all as specified and directed.

S&F 35 mm thick factory made glazed & Skelton shutter of IInd class hard wood open rebated and prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size of stiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I, complete all as specified and directed.

S&F 150mm, mild steel ordinary rat tail rod patttern door springs including roller and roller plate complete all as specified and directed.

S&F 125 mm long extruded aluminium alloy handle, fabricated type, anodised complete all as specified and directed.

S&F 200mm long aluminium anodised,barrel tower bolts of extruded section.hinges complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extrunded sections and fixing bolt and sliding bolt of extrunded sections or cast aluminium alloy complete all as specified and directed.

S&F Steel windows of profile rectangular tube section with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows of profile rectangular tube section with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S&F steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed.

S& F 3 mm thick sheet glass plain ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane complete all as specified and directed.

S& F stainless steel wire cloth 0.36mm nominal dia or wire and average width or apeture 1.40mm and fixed with stainless steel wire staple in complete all as specified and directed.

M&L for framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

M&L for preparation of new wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of syntheatic enammel paint over one coat of pink primer complete all as specified and directed.

M & L for preparation of new or previously untreated steel surfaces of any descirption not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint incl one coat of red oxide complete all as specified and directed.

M & L for preparation of old steel/ wooden surfaces of any descirption not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for mild steel 10 mm dia and over TMT bar cut to length, bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bar 6mm to 8mm dia cut to length bent to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for mild steel TMT bars, 5mm dia and over upto and incl 10mm dia as in stirrups, spacers, binders etc cut to shape requred, incl cranking spirally for hooping for columns, hooking ends binding with and including mild steel wire not less than 0.9mm dia complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on concrete surface of roof finished even and smooth without using extra cement mixed with water proofing compound of approved make as per manufacturers instructions complete all as specified and directed. Note: WPC shall be measured and paid separately.

Supply only integral water proofing compound complete all as specified and directed.

M&L for cleaning of old roof slab surfaces including sweeping clean &washing down with water to remove dust & providing water proofing treatment with polymeric standard water proofing membrane complete all as specified and directed as under : (a) M&L preparation of plaster surfaces /RCC roof surfaces and applying one coat of oil bound bituminous primer @0.30 Ltr/sqm (b) M&L applying bitumen @1.20kg/sqm of grade 85/25 (c) Supplying and laying modified polymeric water proofing membrane super thermo lay 3mm thick of weight not less than 3.00kg /sqm reinforced with polyester non woven fabric weight not less than 150gm/sqm center core including coping on the surfaces with torch application of membrane with 10cm over laps as required all complete all as specified and directed (d) Applying one coat of bitumen 85/25 @1.2 kg/sqm complete all as directed. (e) Applying aluminium paint @ 0.20 kg/sqm complete all as specified and directed.

S&F galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolt, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins complete all as specified and directed.

S&F mild steel work as in hand rails half round or other stock section or core for wooden hand rail straight portion drilled and counter sunk for balusters running bars for doors, balusters, nosing to steps including embeding in concrete and screwing etc., wind ties for roof including securing bolts, post and strut in fencing including cutting tops to shape as directed drilling holes, notching for wire etc. flat iron fillets securing wire mesh including all necessary drilling and bolting and similar work confirming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for preparing surfaces of steel and iron work, treated with two caots of tar or coal tar black paint over 10cm width or girth complete all as specified and directed.

Dismantling asbestos cement (corugated or semicorrugated etc) sheets, in roof covering including ridge complete all as specified and directed.

M&L for Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering/cladding to wall fixed with self tapping screws, complete all as specified and directed.

M&L for Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering/cladding to wall fixed with self tapping screws, complete all as specified and directed.

S&F mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces,etc., complete, drilled for fixing of steel sheeting or other covering doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F Mild steel, plain, black sheet 1mm thick in hearths covering to door shutters covering to door chowkets ( frames ), chullah hood water tanks water troughs ducts urinal troughs and funnels, etc. cut to size, edges beaded ifdirected, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified and directed.

S&F structural steel work as in roof trusses (framed), trussed, purlins crane gantries, rails & fastenings & heavy brackets framimg (Beam, tee, angle, channel or flat section) including distance pieces, cleats etc. Structural steel conforming to Fe-290, Grade-E 165, complete all as specified and directed.

M&L for PCC 1:3:6, type C-1, using 20mm graded crushed stone aggregate as in surface channels and drains finished smooth with using extra cement including necessay form work complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc. 6 m mean radius, built in CM 1:4 complete all as specified and directed..

M & L for 15mm thick rendering on other than fair faces of brick work in CM 1:4 finished even and smooth with using extra cement, complete all as specified and directed.

M&L for precast man hole cover slab using RCC 1:2:4, type B-1 using 20 mm graded crushed stone aggregates set in CM 1:4 complete all as specified and directed.

M&L for RCC 1:2:4, type B-1, nominal mix using 20mm graded stone aggregate for slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified & directed.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exc 200mm thick (horizontal or sloping in rough finished surfaces of concrete complete all as specified and directed.

M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipes with concrete after they are laid and tested; in cement concrete (1:3:6) type C-2 for 300mm dia pipe complete all as specified and directed.

M&L for 300mm bore reinforced concrete pipe class NP-2, laid & jointed in cement sand mortar (1:1) complete all as specified and directed.

M&L for cutting into existing manholes for connecting new drains 150mm dia making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete al as specified and directed.

Taking down carefully point wiring from existing place (light/fan, socket or power points complete) with all fittings such as switches, sockets ceiling rose , pendant holder, fitting and fixtures , MCB, Main switches, call bell etc and making good to disturbed surface to wall ,floor etc to match with existing surface either by using same colour distemper or white colour wash all as required complete all as specified and directed.

M&L for point wiring with colour coding multistranded copper conductor cable, PVC insulated (FRLS) and unsheathed size 1.5 sqmm with concealed Conduit with fixing accessories, to be fixed , with pressed steel concealed terminal boxes covered with 3mm thick laminated sheet incl continous earth wire of PVC insulated unsheathed multi stranded copper conductor cable size 1.5 Sqmm for earth wire connected to common earth dolly, colour code of wires as per specification , complete all as specified and directed for the following :-

All as per Srl Item No 83.00 but for one light /fan/bell point controlled by one, switch complete all as specified and directed.

All as per Srl Item No 83.00 but for one 5 pin 5/6 Amp socket on the same board complete all as specified and directed.

S & F switch piano type 240 V, 6 Amp , Sp one way flush type complete all as specified and directed.

S&F socket 5 pin, 6 Amp, flush type piano (multi purpose) complete all as specified and directed.

S&F ceiling rose surface backelite, 65 x 20 mm three terminal complete all as specified and directed.

S&F sheet metal enclosures for MCB distribution board SPN 8 way double door type with 200 amp rated bus bar and suitable for SPN Isolator as incomer complete all as specified and directed.

S&F MCB SPN 32 to 40 Amps 250V incl all termnials, fitting etc. complete all as specified and directed.

S&F MCB SP 6-32 Amp ,240 Volt incl all termnials, fitting etc. complete all as specified and directed.

M & L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.0 mm thick burried directly in gorund (earth pit not less than 2.25 Mtr normal ground level),and top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanised means of earth wire 4 mm dia with bolts, nuts & check nuts, and washers of galvanised iron protection pipe light grade of 20 mm dia and watering pipe medium grade of 20 mm dia and filled with alternate layer of charcoal and common salt, watering funnel with wire mesh, earth pit chamber and cover CI frame PCC 1:3:6 type C-2 all as shown in electrical plate No-3 of SSR part-I of 2009 connected to earthing test point all as specified including all earth work excavation, returning filling and disposal of surplus soil and testing on completion.

S&F in replacement energy efficient T-8 LED batten integrated type single tube 20 Watt, 4 ft long white complete with LED rod, LED driver and LED batten with extruded aluminium/PC Body and PC diffuser including all accessories pre wire and connecting up with copper three core flexible wire complete all as specified and directed. Make: Cormpton Greaves Cat Part No DMLN1LT8-16 and LTT8-20 or equivalent of C&S/Philips/Wipro/Havells.

S&F in replacement Energy saving LED Street Light Luminaries 45 watt fitting with driver having secondary optics with uniform distribution of light. Pressure die cast aluminum housing powder coated in grey and toughened glass, IP 66 protection, class I with operating voltage range 120 to 270 V, including GI brackets with nuts and bots of suitable size ,making connection from ceiling rose to LED light fitting with suitable cable size for connection complete all as specified and directed. Make :-CROMPTON Cat no - LSTP-45-CDL/ Bajaj Cat No BRTFG 45W LED I/ Polycab Cat No PCGLS T1 45.

Supply, laying and testing of cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core , complete all as specifed and directed.

Supply and laying double walled corrugated (DWC) HDPE duct pipe of 50 mm dia confirming to IS , approved colour complete with fittings for cable protection complete all as specifed and directed.

m/s jupiter builders

S.R.SHARMA & SONS