PROVN OF RCC SHED AND ELECTRIC ACCESSORIES TO COVER THE BIO DEGRADABLE WASTE CONVERSION REACTOR AND SPL REPAIRS TO BAGGAGE STORE AT KOHLI STADIUM AT OLD NAVY NAGAR UNDER AGE BR I OF GE NW NAVY NAGAR COLABA MUMBAI

Amount

Surface excavation n.exc 30 cm deep and average 15 cm deep and getting out in soft and loose soil.

Excavation in trenches not exc 1.5m wide and not exc 1.5m deep for foundation etc or for shafts n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in soft/ loose soil all as specified.

Excavation in trenches exc 1.5m wide and exc 1.5m and n exc 3.0m deep an n.exc 3.0m for foundation etc or for shafts n.ecx 10 Sqm on plan and n.exc 1.5m in depth and getting out in soft/ loose soil all as specified.

M & L for sand filling under floors or in foundation including watering and consolidation

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregates) as in bed concrete for foundation filling & mass concrete.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregates) as in bed concrete for foundation filling & mass concrete.

M&L for brickwork with old size sub class 'B' brick straight or curved on plan exc 6m mean radius built in CM 1:6

M&L Brickwork with old size sub class `B' bricks, straight or curved on plan to any radius in half brick thick wall, built in cement mortar1:4.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25 cm in soft/loose soil

Removing surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point.

M & L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded stone aggregate) in foundation, including rafts, footings, foundation beams, plinth beams; bases for columns, and mass concrete etc complete all as directed.

M & L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded stone aggregate) in Columns, pillars, piers, etc.

M & L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as directed

M & L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span

Steel formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide fair finishes surfaces complete all as specified and directed.

Steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter

Steel formwork for fair finished surface of concrete (flat surface) to sides of pillars, posts, struts, piers, columns, and stanchions

Steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for fair finished surface, not exceeding 200m thick (Horizontal or sloping)

M&L for damp proof course 40mm thk in cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate to horizontal or vertical surfaces including necessary form work

M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

All as per item No 20.00 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L for rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete wall surfaces & finishing the surfaces fair and even all as specified.

M&L Rendering 20 mm thick cement plaster in CM 1:6 on external fair faces of brick/concrete surfaces finished even and smooth (without using extra cement) mixed with WPC (WPC will be measured and paid separately).

M&L for rendering 5 mm thick in CM 1:3 on fair faces of concrete surfaces & finishing the surfaces fair and even on ceiling.

Supply only Integral water proofing compound

M& L for two coats of oil bound distemper on wall over a coat of alkali resistant primer on new plastered surface of walls including preparation of new surface all as specified.

M&L for preparation of new plastered surface & apply two coats of cement base paint over a coat alkali resistant primer all as specified

M&L for preparation of new plastered surfaces and applying three coats of white wash on ceiling

M&L for broken stone/boulders hard core gauge n.exc 63mm deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces.

M&L for 100 mm thick PCC type C-2 1:3:6 (using 40 mm gradded stone aggregate) as in Plinth protection finishing the surfaces even and smooth without using extra cement.

M&L for providing 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base of flooring complete all as directed.

M&L for providing 40mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in flooring even and smooth with using extra cement complete all as directed.

Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade' 'B' , as directed and specified.

S&F 2nd class hard wood plain solid straight chowkhat and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joint.

S&F Factory made 35 mm thick 2nd class hard wood plain framed panelled shutters( two panel) with lock rail and panel of 9mm thick B.W.P commercial ply . The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

S & F for 100 mm butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-21

S & F for 100 mm aluminium handles, cast type, anodised

S & F for 150 mm long aluminium, anodised, barrel tower bolts of extruded section.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp & staple ( bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and slidibg bolts of extruded section or cast-aluminium alloy.

S&F steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete with glazing window dovetailed or welded complete all as specified and directed

S&F Steel ventilators with centre hung shutter including hinges,steel peg stay, complete

M&L framed work such as grills ,grating,etc,with ends of bars shouldered and or riveted or forged into spike; framed guard bars for windows and iron gate confirming to Fe 410-0 or Fe 310-0.

M/L two coats of synthetic enamel paint including preparation of new steel surface over 10cm width or girth over one coat of red oxide primer complete all as specified and directed.

Supply & fix second class hard wood small fittings such as brakets of any type latch and hinge blocks shaped door and window stops and the like including all necessary labours articles n.exc 200 cu cm - each

S & F mild steel flat iron as in hold fast clamps small articles conforming to Fe 290 Gde -E- 165.

M&L PCC 1:3:6 type C1(20 mm graded stone aggregate) as in bed blocks for hold fast including necessary formwork complete.

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm girth or width and applying two coats of synthetic enamel paint over a coat of pink primer.

M&L for precast RCC slabs as in 1:2:4 type B 1 (using 20mm graded stone aggregate) including necessary formwork manhole covers set in cement mortar 1:4

Removal of existing water proofing treatment of the roof, cleaning with wire brushes etc including demolition of PCC padding of any description and in any position including removal of debris up to 250m.

M & L for Plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) mixed with Shali Plast LW+ of STP/Pidilite URP of Dr. Fixit or Equivalent and appoved as per manufactures instruction. Before laying concrete surface shall be cleaned and a bond coat of slurry with Shali Crete URP (of STP) or quivalent with cement to be applied. all cracks in slab to be openend in 'V' groove and filled with Shali Fix RMC a Polymer Morter of STP/ equivalent complete all as specified and as directed.

M&L for 20mm thick rendering in CM 1:4 with the addition of Shaliplast LW+ @ 200ml per bag of cement on fair faces of brick or concrete surfaces all as directed by Engr-In-Charge

M&L for protecting the roof including parapet wall with water proofing coating complete as specified below :-

Clean the surface and apply one coat of primer (STP Shali Urethane BTD diluted in water in 1:1 ratio and applied @ 400 gm/sqm OR Dr, Fixit primeseal diluted in water in 2:1 ratio and applied @ 7-8 sqm/ltr) and allows to dry for 6 to 8 hrs.

Apply first coat of water proofing coating over primer surface (Shali Urethene BTD with non bituminous bleding of STP Ltd. @ 1 Sqm/Ltr without dilution OR Dr. Fixit New Coat without any dilution @ 2 Sqm /Ltr)

Lay Non woven fiber glass mesh (Reinforcement of Shali Geo Text 40/50 gsm of size 2.5mm x 2.5mm) or equivalent with overlap of 50 mm on both direction while the first coat is still wet.

Apply second coat of water proofing coating as per manufactures instruction after 6-8 hrs of drying of first coat.

Apply third coat of water proofing coating (as per manucturer instruction) after 6-8 hrs of drying of second coat The total thickness of 1 to 1.2mm must be achieved after 7 days of air cure. Note : (1) The colour of each coat shall be as directed by GE. (2) The work shall be carried out by authorised applicator only (3) Water proofing to rain water spouts to be done as per manufacturer instruction

Cutting grooves 75mm wide & 65 mm deep in brick wall / RCC surfaces at any location shaping horizontal face with mechanical cutter and grooves filled with PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) mixed with chemical compound SUPER LATEX OR DR FIXIT OF PIDILITE INDUSTRIES LTD or SBR LATEX of STP LTD mixed with proportion 200 ml per 50 Kgs cement as per manufacturers instruction all as specified & directed.

Demolition of Brickwork or stone masonary built in cement mortar not otherwise specified for complete all as specified and directed

M&L Plastering on concrete surfaces of walls 20mm thick (15+5mm)in two coats in CM (1:4) , mixed with water proofing compound on fair faces of brick work or concrete surfaces, finished fair & even without using extra cement complete all as specified (WPC to be mixed in setting coat only and shall be measured and paid separately)

M & L PCC 1:2:4 type B1 ( 20 mm graded stone aggregate ) as in copings of parapet wall including necessary form work complete all as specified and directed

S&F Framed brackets of angles or tee with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles as necessary gusset plates, riveting etc nexc each 10Kg bracket confirming to Fe 410 or Fe 310-0

S&F 10 mm dia 100 mm long dash through fasteners bolts fixed in concrete or brick work to hold brackets etc complete

S&F rolled section as in main and cross beam, hip and jack rafters, purlins where connected to common rafter and running rails etc complete confirming to Fe-410-0 or Fe 310-0

M&L pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified including making grooves of minimum 50mm into brick walling and inserting the sheets into these grooves

Cutting chases, pinning in and making good to facings of brick/concrete/stone walling where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

M&L for filleting in any position and to any shape of section area not exc 25 sq cm in cement sand mortar 1:4 including all mitres, stops etc

Taking down chowkats or frame of any description or specification (wooden/iron/aluminium) (w/o taking off shutters from the frames) but not exc 1.50 sqm each.

All as per item No 63.00 above but exc 1.50 sqm and not exc 4.00 sqm each

Supply and fix in repair aluminium anodised ventilators partly fixed partly louvered including aluminium louveres, frosted glass panes, necessary jamming, glazing pins, neoprene beading, glazing pin screw, rollers, handle etc complete all as specified & directed by Engineer-in-Charge.

M&L preparing wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat pink primer

S&F MS holdfast, wall ties and similar articles confirming to Fe-410-0 or Fe-310-0.

S&F solid PVC door frame of size 50mmx47mm made out 5mm plain colour PVC sheet reinforced with MS square tube made as per specification and drawing.

S & F Factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 100mm size stainless steel butt hinges.

S&F 125mm size extruded aluminium alloy handles, fabricated type anodised.

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L plastering 15 mm thick on other than fair faces of brickwok or concrete surfaces of wall in CM 1:6 and finishing the surface even and smooth without using extra cement and finally providing sagol finish complete

Preparing new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of chalk whitening with wall putty complete

M&L applying one coat of oil emulsion distemper white or tinted on old treated plasterd surfaces of wall after washing, rubbing down and stopping of distemper and painted surface complete all as specified.

M&L one coat of white wash on old ceiling surface after necessary preparation of surface complete all as specified.

Preparing old wooden or wood based surface over 10 cm width and girth and applying one coat of synthetic enamel paint white or tinted complete all as specified.

Preparing of old decorated surfaces of walls complete apply one layer putty washing the surfce thoroughly , filling the cracks, craves with crack-filling-compound (Make : DR FIXIT CRACK SHRINK FREE or Equivalent ) applying two coats of acrylic emulsion exterior grade (100%) over a coat of primer etc all as specified. Note : - (a) Old surface shall be cleaned with bleaching powder as specified and as per manufacturers instructions , all cracks shall be filled with white cement and sand mortar (1:3) by making V- grooves . (b) Acrylic painting shall be done with rollers.(c)Funges formation be cleaned throughly with wire brush or by any means.

Taking down AC rain water pipe of any size or pattern incl all fittings heads, shoes, bends. Swan necks, etc including cleaning for refixing or removing to store.

S&F PVC (SWR) 110 mm bore pipes single socketed, in any lengths with rubber ring joints, fixed to wall with PVC clamp complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bend of any radius with acess door complete all as specified and directed.

Taking down cast iron soil waste pipe (any size or patterns) moulding all fittings heads, shoes, bends etc. (Measured over all as fixed along the confrce line over fittings and accessories).

S&F 100mm bore sand cast CI soil, vent, and waste pipes in any length with or without ears with cement joints fixed to wall with Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof all as specified.

S&F 75 mm bore sand cast CI soil, vent, and waste pipes in any length with or without ears with cement joints fixed to wall with Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof all as specified.

S&F CI bend any radius with oval access door 100mm bore.

S&F CI bend any radius with oval access door 75 mm bore.

S&F CI cowls 100mm bore with cement joints.

S&F CI cowls 75 mm bore with cement joints.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L Vitrified Ceramic tiles (light shade) of size 600mmx600mmx10mm thick (square/ rectangular) polished, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles over and including 15 mm thick cement screed bed in CM (1:6) (Note : The rate includes the cost of 15 mm thick screed bed)

M&L Vitrified Ceramic tiles (light shade) of size 600mmx600mmx10mm thick (square/ rectangular) polished, in vertical surfaces (dado/skirting) etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles over and including 10 mm thick cement plaster in CM (1:4) (Note : The rate includes the cost of cement plaster)

M&L machine cut mirror polished kota stone slab flooring 20-25mm thick over and including 15 mm thick cement screed base in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete (Note : The rate includes the cost of cement screed bed)

M&L machine cut pre-polished kota stone slab 20 to 25 mm thick in riser of steps, skirting, dado and pillar laid over and including 10 mm thick cement in cm (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete (Note : The rate includes the cost of cement plaster )

M&L 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like over and including 15 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite

Rounding to edges of stone slabs (kota/granite etc) one edge, such as in steps, cooking platform, and other similar situations

Extra for forming grooves over granite or kota stone slab as in staircase complete all as specified and as directed

M&L Non - skid coloured ceramic tiles of size 300mm x 300mm x 6 to 7 mm thick in floors over and including 20 mm thick screed bed in cement mortar 1:4. set and jointed in neat cement slurry and grouted with Epoxy grout to match (Note : Cost of 20 mm thick screed bed and epoxy grouting is included in the rate).

M&L glazed ceramic tiles in vertical surface 300x200x 7 mm thick set and jointed in neat cement slurry over and including 10 mm thick cement plaster in cment mortar 1:4 and pointed in white or colour cement to match (Note : The rates include the cost of 10 mm thick plastering)

Demolition of cement concrete of any description and in any position not otherwise specifically provided for including china mozaic, WC etc.

M&L for roughening the surfaces of old cement concrete floor by picking, cleaning and washing down with water to remove dust etc. rendering 15 mm thick in CM 1:3 mixed with water proofing compound and applying two coats of bitumen blown (85/25 grade) @ 1.50 Kg/Sqm over bottom and vertical sides of sunken floors. (Note : WPC shall be measured and paid seperately)

M&L cement concrete 1:7:12 type F2 with 40mm graded stone coarse aggregate in sunken floor all as specified and directed.

M&L vitreous china squatting pan Orissa Pattern, size 580 x 440mm white with integral foot rest including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor

M&L 100 mm bore cast iron 'P' or 'S' trap fixed complete with M seal joint to cast iron 100 mm bore pipe duly fixed in position in repairs complete including closing the wall opening in cm 1:3 as directed

S & F in Vitreous China wash basin, white, flat back, size 550 x 400 mm excluding water taps waste chain plugs and porcelian stopper but including brackets.

S&F CP brass pillar tap 15mm, screwed down high pressure fancy type.

M & L 32 mm dia waste coupling of PTMT (half or full threaded) .(Minimum weight 32mm-45gms)

S & F PVC connectors of 15 mm size with PTMT nuts of length 600 mm length

S & F PVC waste pipe of 32 mm dia 800 mm length

M&L 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets in repairs (Make : Commander/Parryware/Cera)

S&F vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc complete

S&F plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device

S&F in repairs vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets

S&F Aluminium anodised section minimum (thickness of anodising 15 micron) for window / ventilator etc of sliding type comprising frame, shutters, locking arrangements including necessary jamming, glazing pins, neoprene beading, glazing pin screw, rollers, handle etc complete all as specified & directed by Engineer-in-Charge. Note: (a) Glazing shall be measured separately. (b) Item shall be paid as per weight of aluminium section. (c) Rate quoted shall be inclusive of neoprene beading, glazing clips, screw etc as required which not be measured for arriving the weight. (d) Rate shall be inclusive of star locking arrangement including complete packing with silicon gel around contacting surface of aluminium and including matching the existing surface area complete all as specified. (e) Aluminium window / ventilator etc to be fixed with cadmium plated screw not more than 300mm c/c .

M & L 5.5 mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane

S & F in repairs anodized aluminium DECO grills 7.5mm thick, as existing grills, DG - 102

Taking down carefully copper/ aluminium point wiring i.e. light, fan, socket or power/points complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. and making good disturbed surfaces of ceiling, walls, floors, etc.

M & L for point wiring with PVC insulated unsheathed single core multi stranded copper conductor 1.5 sqmm, 1100 volts grade cable, FRLS, passing through PVC casing caping including accessories and provision of PVC box for mounting of modular Switchs & Sockets as required at site as directed by Engineer-in-Charge including one run of PVC insulated unsheathed multistranded copper conductor cable 1.5 sqmm (green colour) FRLS earth wire and connected to earth dolly for the following:- NOTE : Circuit conductor from MCB DB to Switch boards should not be less than 2.5 sqmm.

One light/Exhaust/Ceiling fan point controlled by one switch.

One 3 pin switch socket combination 5 Amps on the same board with other switches.

One 3 pin switch socket combination 5 Amps, independent.

All as per item No 118.00 above but with 2.5 sqmm cable for one three pin 15 Amps socket out let controlled by one switch.

S & F in replacement with modular switch, 1 module, single pole one way 6Amp.

S & F in replacement with modular switch, 1 module, single pole one way 16Amp.

S & F in replacement with ceiling rose with earth terminal connection, 3 terminal/ PVC/ polycarbonate, isolated body of size 60x50mm

S & F in replacement with modular socket 2/3 pin, 2 module, 6A.

S & F in replaement with new modular socket 2/5 pin, 2 module, 6A, ISI marked, 230 volts.

S & F in replacement with Socket 6/16A, 6 pin, 2 module, ISI marked, 240 volts all as specified

S & F in replacement with modular stepped type fan regulator, 2 module, single pole one way, 230 volts ISI marked and connecting up complete.

Taking out old wooden/PVC board and disconnecting all electric connection from switches, board and S & F modular PVC Gang box, screwless, with silver border of 8 module for mounting of modular switches and sockets including blank plate for blank module.

All as per Item No 128.00 above but of modular PVC Gang box, 3 module.

All as per Item No 128.00 above but of modular PVC Gang box, 2 module.

All as per Item No 128.00 above but of modular PVC Gang box, 1 module.

S&F modular white cover plate with frame, 12 module.

S&F modular white cover plate with frame, 8 module.

S&F modular white cover plate with frame, 6 module.

S&F modular white cover plate with frame, 4 module.

S&F modular white cover plate with frame, 3 module.

S&F modular white cover plate with frame, 1 or 2 module.

Taking out old wooden/PVC board and disconnecting all electric connection from switches, board and S & F modular metal flush box 12 module for mounting of modular switches and blank plate.

All as per Item No 138.00 above but of modular metal flush box, 8 module.

All as per Item No 138.00 above but of modular metal flush box, 6 module.

All as per Item No 138.00 above but of modular metal flush box, 4 module.

All as per Item No 138.00 above but of modular metal flush box, 3 module.

All as per Item No 138.00 above but of modular metal flush box, 1/2 module.

Taking down unserviceable FTL and supply and fix Slim LED integrated batten of 20Watt 4ft coolday light with powder coated CRCA decorative patti prewired complete with two Nos of PVC box of size 75x75x20mm for mounting light fittings including ceiling rose complete. Make of Light Fitting : Wipro Cat Part No D53206520 watts or BN 021C LED 20S PSU CDL GR of Philips F9 or BCLSB20W WH LED of Bajaj.

All as per Item No 144.00 above but Slim LED integrated batten of 10 Watt 2ft complete. Make of Light Fitting : C&S Cat Part No LTTB2F10WLED/W or BN021 LED10S 6500 PSU GRS1 of Philips or BCLSB10WH LED of Bajaj.

Taking out unserviceable ceiling fan deposit to MES Store and S&F in repair ceiling fan 1200mm sweep, 230V, 50Hz, hanging on ceiling and connect with copper conductor multi stranded 3 core wire of size 14/0.0076. Make- : Bajaj/Havells/Orient/USHA.

Taking out unserviceable Exhaust Fan deposit to MES Store and S&F Exhaust fan, 4 blade, heavy duty, double ball bearing, 230V, 50Hz,300mm sweep having power input 70W speed 1440RPM, with protective bird guard including connection as required at site with flexible copper cable all as per specified and directed. Make :- Havells/CG/Bajaj/Almonard/USHA.

Supply, laying and commissioning, testing PVC heavy duty electric cable with aluminium conductor, 1100 volts grade of size 10 sqmm 4 core laid in trenches, passing through pipes, fixed on walls complete including connecting properly by means of thimbles/bottle lugs.

S & F cable PVC insulated, PVC sheathed, armoured, FRLS, 1100V grade, 2 core 6 sqmm stranded copper conductor electric cable laid on wall/ roof/ duct complete with proper saddling and connecting to DBs with glands including taking out existing unserviceable cable complete all as specified.

M&L for sheet metal enclosure for TPN DBs vertical 4 way with 01 Nos MCCB 63 Amps, 25 KA as incommer and 03 Nos SPN 32 Amps as outgoing when MCB to be used TPN 04 way, double door, IP-08, IK-09, 240V having Din rail, Neutral & Earthing bar complete all as specified and directed.

Taking down old Main switches/MCB DB any way with safety, any type complete all as specified and as directed.

S & F MCB DB SPN confirming to IP 43-IK 09 with acrylic door, 8 way complete with din rail, Neutral and Earthing bar complete and making good the disturbed surfaces.

S & F MCB SPN, 10 to 25Amp, 10KA, 230Volt.

S & F MCB, single pole, upto 20Amp, 10KA, 230Volt.

Taking down existing sub main wiring with existing conduit if exist and refixing the same in existing location after replacing Cable/conduit clamps with new as existing including making all connection from meter panel to DB all as specified and as directed by Engr- in-Charge.

Taking down deteriorated louvers from site and supplying and fix new louvers made out of 16mm GI sheet with machine pressed cut for horizontal ventilation suitable for 300mm sweep exhaust fan complete all as specified and as directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.5 mtr wide not exceeding 1.5 mtr in depth and getting out in soft/loose soil all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25 cms in any type of soil all as specified.

Removing excavated material exc 150 M but n. exc 500 M and depositing where directed all as specified.

Supply and lay pipe galvanized, "Medium class", including fittings 40 mm (1.5") dia

Supply and fix gate valve of size 40 mm, cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe with union all as directed by Engineer in charge.

Supply and fix 3 layer ( inner antimicrobial, outer UV stabilized) ISI marked blue colour IS-15801, PP-R pipes SDR -7.4 (PN-1.6) and PP-R plain fittings including all fittings, reducers and fixed complete and concealed in walls and ceilings or laid in floors in short piece/length complete all as specified and directed by Engineer-in-charge for the following size of

(a) 20mm External dia

(b) 32mm External dia

Supply and fix bib cock long body with flange of size 15mm

Supply and fix concealed stop cock regular body of size 15mm

Supply and fix Brass chromium plated shower with 225mm arm of size 15mm

Supply & fixing in repair PVC (LLDPE) rectangular loft tank of net capacity 275 ltrs with gross capacity of tank at least 5% in excess of minimum net capacity including 03 Nos adapter with washer for inlet/outlet over flow as per manufactureres instructions and over all dimensions as 995-1200mm length, 620-820mm width, 285-485mm height, 300mm internal dia of hand hole, minimum wall thickness 2.75mm, weight of tank 11 kgs withoutlid complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair replacement of PVC profile suitable for 275 ltr loft tank including fixing of aluminium channel around the profile completing all as specified and directed.

Supply and fix in repair/replacement float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed (Flat type) for iron pipe and fixed 15 mm bore.

Supply and fix in repair/replacement float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed (Flat type) for iron pipe and fixed 40 mm bore.

Disconnecting all incoming & outgoing pipe connection taking out unserviceable PVC water storage tank, supply & fixing PVC Triple layer and UV protected water storage tank of capacity 3000 Ltrs, hosting and fixing in position at any location connecting with existing inlet/outlet pipe up to 40 mm bore GI pipe connection completely all as specified and directed.

Supply and Fix PPR gate valve brass inserted of size 32mm

Supply & Fixing in repairs Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks fkand the like inlcuding caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc with FE 410 -W (Gde-E-250)

BOB ENTERPRISES