Repair Renovation of 06 Nos. GPA Ty-I Qtrs namely Ty-I 94/95, 91/92 and 85/86 at Mayabunder under Maintenance Section of Sub Division No.I, NACD, APWD, Mayabunder including IEI.

Amount

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge:

All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 40 mm nominal size derived from natural sources).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III)derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for

Shelves (Cast in situ)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Hard drawn steel wire fabric

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. a) Granite of any colour and shade.

Area of slab upto 0.50 sqm

Area of slab over 0.50 sqm

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to steel windows by welding

Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete.

300 mm weighing not less than 200 gms

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing.

30 mm thick plain PVC door shutters

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Electric resistance or induction butt welded tubes

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing bolts including nuts and washers complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :

5.5 mm thick glass panes

Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete.

Extra for making chequers of approved pattern on cement concrete floors, steps, landing, pavements etc.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Bend 87.5° i) 110 mm bend

Providing and fixing pre-painted galvalume (PPGL) steel profile sheets AZ-150 of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd. or equalavent (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with aluminium zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling / self tapping aluminium screws (Xylan) of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500 - 600mm)

Gutter (600 mm over all girth)

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :

New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade :

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area 3 sq. metres and below

Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead :

Of sectional area 40 square centimetres and above

Of sectional area below 40 square centimetres

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:

Asbestos Cement sheet

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink without drain board i) 610x510 mm bowl depth 200 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe i) 32 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

25 mm nominal dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work

50 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :

50 to 80 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

40 mm nominal bore

50 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length i) 15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

100 mm diameter

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15mm nominal bore

Dismantling of manhole including R.C.C. top slab, C.I. cover with frame, including stacking of useful materials near the site and disposal of unserviceable materials within 50 m lead as per direction of Engineer-in-charge:

Rectangular manhole 90x80 cm and 45 cm deep

Extra for depth of manholes dismantled :

Rectangular manhole 90x80 cm and beyond 45 cm depth

Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately).

Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer-in-charge.

Providing and fixing PVC door baffur 80mm long.

Extra for providing frosted glass panes 5.5mm thick instead of ordinary float glass panes 5.5mm thick in doors, windows, and clerestory windows shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured ( In Bathroom & w.c Ventilations.)

Providing and fixing eaves or facia baord with 19mm thick Hilux board 30 cm wide including fixing with GI nut and bolts etc. complete.

Dismantling of PVC door with frame & shutter,including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. all complete as per the direction of EIC.

Providing and fixing plain multipurpose cement board(High pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).

Decorative Type - 6 mm thick Cement fiber board as per IS: 14862

Dismantling of eaves or facia board (WPC/Timber) along with its nut bolts for eaves height upto 10 metres including stacking the material within 50 metres lead.

Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing stainless steel Floor grating of approved quality as per direction of Engineer-in-charge.

Providing and fixing C.P. brass towel rail complete with brackets fixed to wooden cleats with C.P. brass screws with concealed fittings arrangements of approved quality.

600mm long towel rail.

Providing and fixing C.P. Soap Dish Holder having length of 138mm , breadth 102mm, height of 75mm width concealed fittings arrangements , Weighing not less than 106 gms of approved quality (Of Jaguar, Hindware , Parryware or equivalent).

Extra length for providing connection flush pipe connecting with orissa pattern WC pan 32mm dia.

Providing and laying hollow block cement concrete block walling 200mm thick consisting of hollow block of size 400mm x 200mm x 200mm of mix 1:3:6 (1 cement; 3 coarse sand; 6 graded stone aggregate 10mm nominal size) having a crushing strength of 3.5 N/Sqm at 28 days as per IS:2185 (Part-I) 1979 laid in cement mortar 1:6 (1 cement; 6 coarse sand) upto floor five level.

Providing and fixing unplastisized G.I. pipe clips of approved design to unplastiside sized PVC sanitary waste pipes by means of 50x50x50mm hard wood plugs screwed with MS screws of required length including cutting brick work and fixing with a cement mortar 1:4 and making good the wall etc complete.

110 mm dia pipe.

75 mm dia pipe.

Providing and fixing soil, waste and vent pipes with UPVC pipe conforming to IS:13592 Type B including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion. (i) Single socketed pipes.

110 mm dia pipe.

75 mm dia pipe.

Providing and fixing UPVC moulded self cleaning trap design with screw down or hinged grating with arm complete including cost cutting and making good the walls and floors Grating shall be stainless steel of 100mm dia.

100mm inlet and 75mm outlet.

Providing and fixing CPVC Union in CPVC pipe including cutting and threading the pipe and making long screws etc. complete.

25 mm nominal bore

Providing and fixing CPVC Tank Nipple (Tank Connector pipe) for water tank pipe, fittings of approved quality and colour. a) 25mm nominal bore

Providing and fixing CPVC Ball Valve of approved quality High or low pressure with plastic floats complete.

25 mm nominal bore

Providing and fixing UPVC moulded single equal plain junction of required degree with access door insersion rubber washer 3mm thick, bolts and nuts complete for UPVC soil pipes conforming to IS:13592 Type B including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion.

Providing and fixing UPVC moulded plain bend of required degree for UPVC soil pipes conforming to IS:13592 Type B including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion.

Providing and fixing UPVC terminal guard.

Extra for providing and fixing wind ties of 40x6mm flat aluminium section with necessary screws etc.

Providing cement concrete surface drain including earthwork in excavation, 10 cm thick base concrete and 15 cm thick side walling with 1:3:6 (1 cement; 3 coarse sand; 6 graded stone aggregate 40mm nominal size) finishing with 1:4 (1 cement; 4 sand) including floating coat of neat cement including drain and its top and exposed surface including earth work in excavation and disposal of surplus earth etc. complete.

23x23 cm surface drain.

Construction of 2.80m ht Steel Staging of Platform Size 3.00X1.60m provided with 06Nos of RCC Short Column (300mm x 300mm size) with foundation footing for each and foundation depth of 1.20 Mtr with short column raised to 100mm above G.L and erecting Pre- fabricated staging over the short column base by means of base bearing plates & Foundation bolts. etc complete., Including Pre-Fabrication of 01 nos of Steel Staging of top platform size 3.00m Length & 1.60m width Top platform welded over with 20Gauge thick GI Sheet and staging frame of 06nos of 65dia GI Pipes in vertical posts and 40mm dia GI Pipes horizontal tie members & cross bracings provided as required in all of its four sides & 50dia GI Pipe in outer frame of Top platform with 32mm dia GI pipes in its intermediate spaced @ 150c/c , complete unit made out of GI pipes and painted with black anti corrosive bitumastic paint complete as per enclosed detailed drawing sketch & direction of EIC.

Providing, hoisting and fixing upto floor five level precast reinforced cement concrete in shelves including setting in cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centring, shuttering and finishing with neat cement punning on exposed surfaces but excluding the cost of reinforcement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size).

Extra for providing and fixing Aliminium Channel beading of approved shape and composite units in the Steel glazed windows as per the direction of Engineer-in-charge.

Constructing C.C manhole 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 40mm nominal size) with 15cm thick R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), & 200mm thick foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggreate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design.

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

Extra for depth for manholes Size 90x80 cm With cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 40mm nominal size)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

Group A

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required.

100 mm X 100 mm X 60 mm deep

150 mm X 75 mm X 60 mm deep

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required.

5/6 amps switch

3 pin 5/6 A socket outlet

TV antenna socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing metal box of 150mm X 75mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch, connections, painting etc. as required.

Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type switch, connections, painting etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying and fixing PVC batten/ angle holder including connections etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

12 way , Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and re-filling as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Supplying of LED 9 Watts 3 star rating B22 WW lamp similar to Havells Adore Cat No.LHLDEUEEML8R009 6500K or equivalent as required.

Supplying of Batten for LED tubes equivalent to HAVELLS REGAL BATTENT8UPTO1X22WSSBSWH including 20W LED Tube lamp equivalent to HAVELLS CRYSTAL GLASS LED TUBE LIGHT (Double side connection) Cat No. CRYSTAL1213T8DSTL20WLED865SGLASS complete or its equivalent to ISI standard.

Supplying of 10W LED Bulk Head environment friendly, ultra modern, energy saving, surface mounted, decorative hexogen bulk head Back-lit LED luminaire comprising of high brightness LEDs equivalent to Havells HEXA 10W - IP66 Cat No.HEXAFT10WLED857SSYMBOPC etc. or its equivalent to ISI standard.

Supplying of 8 W Mirror light self ballasted LED Batten, extruded thermoplastic body with PC diffuser in unique square shape, >180º wide distribution equivalent to Polycab INTENSO LXS LED BATTEN - PC PROFILE Cat No. INTENSO LXS LED BATTEN 1 FEET 8W 6500K complete or its equivalent to ISI standard etc. as required.

Supplying of AC Ceiling fan 1200 mm sweep similar to Bajaj KESSEL 50 ISI (white) without regulator etc. or equivalent to ISI standard.

Supplying of exhaust fan of size 300 mm sweep with protective bird guard similar to Havells Ventil Air DSP or make: Bajaj / Usha / Crompton or its equivalent to ISI standard.

Providing and eraction of single phase metering box made out of SMC of size 250 x 250 x 155 with hinged cover and locking arrangements, viewing glass etc. as required similar to Sintex Model No. GSMB 2525.

S B SHARMA