Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹13.2 LAccepted-AOC H NO 1237 PANA PAPOSIAN NARELA NORTH WEST DELHI NEW DELHI 110 040 | NEW DELHI | NORTH WEST DELHI | DELHI | 110040 | L1 | Accepted-AOC L1 | |
| 2 | L2₹15.8 L+₹1.9 L (13.7%)Rejected-Finance 20 8 EWS PREETAM NAGAR COLONY ALLAHABAD | PRAYAGRAJ | UTTAR PRADESH | 211001 | L2 | Rejected-Finance Being not lowest tenderer | |
| 3 | L3₹20.0 L+₹6.1 L (44.0%)Rejected-Finance | L3 | Rejected-Finance Being not lowest tenderer | |
| 4 | L4₹20.0 L+₹6.1 L (44.2%)Rejected-Finance | L4 | Rejected-Finance Being not lowest tenderer | |
| 5 | L5₹22.6 L+₹8.7 L (62.9%)Rejected-Finance 3788 SHAH GANJ GB ROAD NEW DELHI 110006 | NORTH | DELHI | 110006 | L5 | Rejected-Finance Being not lowest tenderer |
| Sl No | Description | Qty | Unit | M/S HARINDER SINGH L1 | M/S Anand Enterprises L5 | M/s Prakash Enterprises L3 | MOHIT ENTERPRISES L2 | M/s R P Enterprises L4 | S K ENGINEERS AND CONTRACTOR L6 | mahadev enterprises L8 | AS Engineering L7 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1.00 | Taking down the existing old LT panel board/ LT feeder pillar box/ power factor panel comprising of MCCB & switch fuse unit of any capacity and size including aluminium bus bar, ammeters, voltmeters etc after disconnecting all cable connections and removing from site complete all as specified and directed by Engr-in-charge. | 4 | Each Job | 99 ₹396 Lowest | 500 ₹2,000 | 100 ₹400 | 449.99 ₹1,799.96 | 199 ₹796 | 4,500 ₹18,000 | 251 ₹1,004 | 2,000 ₹8,000 |
| 2.00 | S & F in replacement of LT Panel board outdoor type, double door, fabricated made of MS / CRCA sheet 3.15 mm thick with MS angle frame of size 40 X 40 x 6 mm with lockibg arrangements slanting roof and size of LT panel / feeder pillar box with suitable size including 04 Nos legs with necessary PCC work of suitable size of PCC 1:2:4 including necessary insulators and 04 Nos of copper bus bar of size 30 mm X 5 mm capacity, provision of inlet and outlet cable glands and earth connection lead etc complete and connection of all incoming and outgoing cable using aluminium terminal sockets / lugs duly crimpled and necessary two coats of paint with approved make and colour an grade of first quality synthetic enamel paint over a coat of red oxide primer including necessary preparation of surfaces and the panel should be dust and vermin proof factory fabricated, CPRI approved totally enclosed free standing / wall mounting type suitable for 415 volts, 50 Hz 3 phase 4 wire system complete in all respect and confirming to latest relevant of ISI specifications including necessary connections, inter connections with copper conductor cable of required size including MS angle frame of size 40 X 40 X 5 mm structure at bottom, and with including the following accessories :-
INCOMING : (i) MCCB, AC 415 volts, adjustable thermal & adjustable magnetic setting, 4 pole current rating 400 Amps, breaking capacity 36 KA = 01 No
(ii) 4 strip copper bus bar of size 40x10mm with specific colour (R,Y,B) insulation - 01 set
(iii) Metering panel comprising, voltmeter and ammeter, digital type with selector switches CTs, control fused and indicating lamps.
OUTGOING : (i) MCCB, AC 415 volts, 4 pole current rating 200 Amps, breaking capacity 16 KA = 03 No’s.
(ii) MCCB, AC 415 volts, 4 pole current rating 40 Amps, breaking capacity 10 KA = 02 No’s.
(iii) Spare blanking way for one No extra out going MCCB = 02 Nos
(iv) Digital Voltmeter 0-500 Volts - 01 Nos.
(v) Digital Ammeter 04-400 Amps - 01 Nos.
(vi) Indicator lamps Red, Yellow & Blue.
(vii) Complete wiring of the panel board.
(viii) CT ratio 400/5 Amps. | 3 | Each Job | 1,10,000 ₹3,30,000 | 2,10,000 ₹6,30,000 | 1,20,000 ₹3,60,000 | 79,999.99 ₹2,39,999.97 Lowest | 1,20,000 ₹3,60,000 | 1,76,000 ₹5,28,000 | 1,75,001 ₹5,25,003 | 2,90,000 ₹8,70,000 |
| 3.00 | Supply, fabrication, installation & commissioning in replacement of Automatic Power Factor Correction (APFC) Panel for 3 Phase, 415 V & 50 Hz system of capacity 60 KVAR without incoming MCCBs made out of MS/ CRCA sheet 3.15 mm thick with MS angle iron frame of size 40 X 40 X 6mm outdoor type front door opening with locking arrangement slanting roof for suitable all as specified and directed by Engr-in-Charge. | 1 | Each | 70,000 ₹70,000 | 2,10,000 ₹2,10,000 | 50,000 ₹50,000 | 59,999.99 ₹59,999.99 | 88,000 ₹88,000 | 1,39,000 ₹1,39,000 | 3,501 ₹3,501 Lowest | 1,25,000 ₹1,25,000 |
| 4.00 | Supply and fixing in replacement energy saving LED street light of 60 Watt Capacity high pressure die cast aluminium housing with seal toughned glass cover, light source should be multi LED SMD system efficacy should be minimum 110 lumen/watt cool/warm as per site requirement ,voltage range 120 -220 Volts IP -66 THD Less than 10% surge protection minimum 5 KV with flash indication, driver should be potted / CE cretified/R cetificate and Driver efficiency 85% including making connection complete all as specified and as directed. | 7 | Each | 5,000 ₹35,000 | 2,500 ₹17,500 | 1,500 ₹10,500 Lowest | 3,699.99 ₹25,899.93 | 5,000 ₹35,000 | 1,900 ₹13,300 | 3,601 ₹25,207 | 1,750 ₹12,250 |
| 5.00 | Supply and erecting in true vertical position steel tubular swaged pole 09 mtr long type 410 SP-31) complete with base plate and bracket fixed at top , painted internally throughout and externally up to the embeeded depth with two coats of black bitumnous paint and remaining external portion with two coats of aluminium paint over a coat of red oxide primer including providing 30cm wide alternate strips with sky blue and white synthetic enamal paint upto 1.2m high from ground level including excavation work (1.5*0.6*0.6 mtr) and PCC (0.6*0.6*1.5 Mtr) for erecting electric pole of length 9 mtr pole complete all as specified and directed. | 7 | Each | 10,000 ₹70,000 | 16,000 ₹1,12,000 | 15,000 ₹1,05,000 | 9,999.99 ₹69,999.93 | 12,000 ₹84,000 | 16,900 ₹1,18,300 | 10,501 ₹73,507 | 9,500 ₹66,500 Lowest |
| 6.00 | Supply and fix in repairs pole mounting junction boxes made out of SMC of size 250 x 200 x 105 mm (HxWxD) with 3 phase strip and 1 neutral strip, side hinged door fixed to the base with hinges suitable for 4 wire system including MCB SP 6 Amps 240 volts - 01 No, Shock proof and rustproof Cable entry from bottom and or sides,100% weatherproof, including Pole mounting arrangement like clamps, nuts etc, maintenance-free complete all as specified and directed. Make- Sintex or ISI marked. | 7 | Each Job | 400 ₹2,800 | 800 ₹5,600 | 600 ₹4,200 | 399.99 ₹2,799.93 Lowest | 530 ₹3,710 | 890 ₹6,230 | 1,001 ₹7,007 | 850 ₹5,950 |
| 7.00 | M & L in replacement of PCC 1:3:6 type C2 using 40 mm grade stone aggregate as in mass concrete for filling in foundation of stay/pole including necessary form work complete all as specified and directed by Engr-in-Charge. | 6.5 | Cum | 2,000 ₹13,000 | 1,500 ₹9,750 Lowest | 2,000 ₹13,000 | 1,599.99 ₹10,399.94 | 5,500 ₹35,750 | 3,200 ₹20,800 | 4,501 ₹29,256.5 | 5,000 ₹32,500 |
| 8.00 | M&L for Plain Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate for coping around poles, earth pit ,including provision of necessary form work, finishing even and smooth without using extra cement including applying exterior emulsion paint (apex) complete all as specified and as directed by Engr-in-Charge. | 0.4 | Cum | 2,000 ₹800 | 1,500 ₹600 Lowest | 5,000 ₹2,000 | 3,599.99 ₹1,440 | 8,300 ₹3,320 | 3,600 ₹1,440 | 5,201 ₹2,080.4 | 6,500 ₹2,600 |
| 9.00 | M&L in repairs of physical inspection for earthing health and to check the healthiness of earthing system whether the resistance under safe limits of resistance IF higher than the permissible then recharging of earthing should be done immediately with carbon based low resistivity compound 0.001 ohm meter recharging of existing earth pit by excavating soil up to electrode depth approx 10 feet by manual drilling (post hole) method and filling with backfill compound maintenance free earthing compound with 2 bags of 20 Kg to achieve desired resistance value less than 1 ohms in and including water up to top of the excavated bore, backfilling of earth pit, measuring the value after refilling pit and testing of earthing after recharging, reconnecting grounding electrode conductor and earth grid applying petroleum jelly etc. to bolted joints to minimise corrosion for the pipe earthing or plate earthing then gel should be used to lower down the resistance complete all as specified and as directed by Engr-in-charge.
Notes :
(i) In case of satisfactory results not found or results degraded during one year of recharging of the earthing, the same shall be made good / recharged again in order to have required test results within contract / Defect liability period without any extra cost to the department.
(ii) Contractor will mark each earthing with CA No., date of recharging of earthing on MS sheet size 18"x12" x 1/8" with suitable mounting arrangement on wall or on ground duly painting blue over a coat of Red Oxide primer and letter/figures of words written with white colour. Quoted rate will be deemed to have been included the cost of the same. Make of backfill compound: Akaltech / Curenite | 120 | Each Job | 55 ₹6,600 Lowest | 100 ₹12,000 | 500 ₹60,000 | 229.99 ₹27,598.8 | 220 ₹26,400 | 700 ₹84,000 | 1,901 ₹2,28,120 | 520 ₹62,400 |
| 10.00 | M&L for dismantling of old existing earthing PCC earthing pit with cover and S & F new polyplastic earth pit cover heavy duty with sign board triangular shape, making connection of earth strip including minor adjustment, construction of rectangular of size 0.75X0.75X0.50 (LXBXH) brick boundary alongwith necessary plastering work with specified colour coding around poly plastic earth pit cover, complete all as specified and directed by Engr-in-Charge. | 60 | Each Job | 100 ₹6,000 Lowest | 400 ₹24,000 | 500 ₹30,000 | 299.99 ₹17,999.4 | 200 ₹12,000 | 560 ₹33,600 | 801 ₹48,060 | 600 ₹36,000 |
Tender Value
₹28 L
EMD Value
₹56,000
Closing Date
7 Oct 2025, 6:00 pmClosed
GE AF Tughlakabad
GE AF TUGHLAKABAD SANGAM VIHAR PO NEW DELHI 110080
REPAIR/MAINT OF LT PANEL, CAPACITOR TANK INCLUDING CONTROL EQUPIPMENT AND OTHER WORK AT AF STN NAJAFGARH UNDER GE (AF) TUGHLAKABAD
2025_MES_731058_1
GE/TKD-55/2025-26
Open Tender
Electrical and Maintenance Works
Works
180 days
GE AF Tughlakabad
As per NIT conditions
8 documents required · 8 mandatory
₹0
₹56,000
Yes
3 Dec 2025
16 Sept 2025
9 Oct 2025
16 Sept 2025
7 Oct 2025
1 Oct 2025
Amount
Taking down the existing old LT panel board/ LT feeder pillar box/ power factor panel comprising of MCCB & switch fuse unit of any capacity and size including aluminium bus bar, ammeters, voltmeters etc after disconnecting all cable connections and removing from site complete all as specified and directed by Engr-in-charge.
Supply, fabrication, installation & commissioning in replacement of Automatic Power Factor Correction (APFC) Panel for 3 Phase, 415 V & 50 Hz system of capacity 60 KVAR without incoming MCCBs made out of MS/ CRCA sheet 3.15 mm thick with MS angle iron frame of size 40 X 40 X 6mm outdoor type front door opening with locking arrangement slanting roof for suitable all as specified and directed by Engr-in-Charge.
Supply and fixing in replacement energy saving LED street light of 60 Watt Capacity high pressure die cast aluminium housing with seal toughned glass cover, light source should be multi LED SMD system efficacy should be minimum 110 lumen/watt cool/warm as per site requirement ,voltage range 120 -220 Volts IP -66 THD Less than 10% surge protection minimum 5 KV with flash indication, driver should be potted / CE cretified/R cetificate and Driver efficiency 85% including making connection complete all as specified and as directed.
Supply and erecting in true vertical position steel tubular swaged pole 09 mtr long type 410 SP-31) complete with base plate and bracket fixed at top , painted internally throughout and externally up to the embeeded depth with two coats of black bitumnous paint and remaining external portion with two coats of aluminium paint over a coat of red oxide primer including providing 30cm wide alternate strips with sky blue and white synthetic enamal paint upto 1.2m high from ground level including excavation work (1.5*0.6*0.6 mtr) and PCC (0.6*0.6*1.5 Mtr) for erecting electric pole of length 9 mtr pole complete all as specified and directed.
Supply and fix in repairs pole mounting junction boxes made out of SMC of size 250 x 200 x 105 mm (HxWxD) with 3 phase strip and 1 neutral strip, side hinged door fixed to the base with hinges suitable for 4 wire system including MCB SP 6 Amps 240 volts - 01 No, Shock proof and rustproof Cable entry from bottom and or sides,100% weatherproof, including Pole mounting arrangement like clamps, nuts etc, maintenance-free complete all as specified and directed. Make- Sintex or ISI marked.
M & L in replacement of PCC 1:3:6 type C2 using 40 mm grade stone aggregate as in mass concrete for filling in foundation of stay/pole including necessary form work complete all as specified and directed by Engr-in-Charge.
M&L for Plain Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate for coping around poles, earth pit ,including provision of necessary form work, finishing even and smooth without using extra cement including applying exterior emulsion paint (apex) complete all as specified and as directed by Engr-in-Charge.
M&L in repairs of physical inspection for earthing health and to check the healthiness of earthing system whether the resistance under safe limits of resistance IF higher than the permissible then recharging of earthing should be done immediately with carbon based low resistivity compound 0.001 ohm meter recharging of existing earth pit by excavating soil up to electrode depth approx 10 feet by manual drilling (post hole) method and filling with backfill compound maintenance free earthing compound with 2 bags of 20 Kg to achieve desired resistance value less than 1 ohms in and including water up to top of the excavated bore, backfilling of earth pit, measuring the value after refilling pit and testing of earthing after recharging, reconnecting grounding electrode conductor and earth grid applying petroleum jelly etc. to bolted joints to minimise corrosion for the pipe earthing or plate earthing then gel should be used to lower down the resistance complete all as specified and as directed by Engr-in-charge. Notes : (i) In case of satisfactory results not found or results degraded during one year of recharging of the earthing, the same shall be made good / recharged again in order to have required test results within contract / Defect liability period without any extra cost to the department. (ii) Contractor will mark each earthing with CA No., date of recharging of earthing on MS sheet size 18"x12" x 1/8" with suitable mounting arrangement on wall or on ground duly painting blue over a coat of Red Oxide primer and letter/figures of words written with white colour. Quoted rate will be deemed to have been included the cost of the same. Make of backfill compound: Akaltech / Curenite
M&L for dismantling of old existing earthing PCC earthing pit with cover and S & F new polyplastic earth pit cover heavy duty with sign board triangular shape, making connection of earth strip including minor adjustment, construction of rectangular of size 0.75X0.75X0.50 (LXBXH) brick boundary alongwith necessary plastering work with specified colour coding around poly plastic earth pit cover, complete all as specified and directed by Engr-in-Charge.
S&F copper strip of size 32 mm x 6 mm for roof conductors and down conductors above ground including PVC insulators of pasting with suitable heat resistant gum type solution complete all as specified and directed by the Engr-in-charge. Note : Any type of screw / fasteners / grouting materials are strictily not recommended by station HQ.
S&F copper strip of size 20 mm x 3 mm for roof conductors and down conductors above ground including PVC insulators of pasting with suitable heat resistant gum type solution complete all as specified and directed by the Engr-in-charge. Note : Any type of screw / fasteners / grouting materials are strictily not recommended by station HQ.
M&L for copper brazing (welding) at site to connect loop copper earthing strip of any size after tightening by nut, bolt, washer, check nuts of brass complete all as specified and as directed by Engr-in-charge. Note: Copper brazing shall be done upto 20 mtr height. Necessary tool/plant and ladder required for working upto 20 mtr height shall be deemed to be included in the rate quoted for above item.
M&L for GI brazing (welding) at site to connect loop GI earthing strip of any size after tighten by nut, bolt, washer, check nuts, complete all as specified and as directed by Engr-in-charge. Note: GI brazing shall be done upto 20 mtr height. Necessary tool/plant and ladder required for working upto 20 mtr height shall be deemed to be included in the rate quoted for above item.
S&F in replacement of test point terminal block made of gun metal or phosphorus bronze of size 75x75x25 mm drilled and screwed including 3 Nos 8 mm dia 25 mm long hexagonal head screw fixed inside cubical shape enclosure made out of CRCA sheet 2 mm thick with front detachable cover, anodized screws, cap washers 4 Nos to be mounted on wall with wooden plugs and screws 4 Nos duly painted inside and outside by two coats of aluminium paint over a coat of primer over all dimension of enclosure 200x150x100 mm (depth) complete all as specified and directed by Engr-in-charge.
Testing of earthing Resistance as and when required with digital earth resistance tester etc in presence of user & MES rep and maintaining duly entering test results in the binding register for maintaining the record with Engr-in-charge complete all as specified and directed by the Engr-in-charge. Note: (i) Contractor shall carry out within two days of intimation to carry the test as a whole or partially of the building complete all as directed by Engr-in-charge. (ii) Earth testing will be carried out as and when required basis as directed by Engr-in-charge. (iii) Each earthing will be measured and paid separately as and when test was carried out.
S&F in replacement of lightening conductor air termination, single pointed copper rod of 12 mm long including fixing of MS clamps with nuts, bolts and screws complete all as specified and directed by Engr-in-charge. Note : The PCC block shall be constructed in PCC 1:2:4 type B1 using (using 20mm grade stone aggregate) of size 200 X 200 X 200 mm including putting 15 mm dia GI medium grade pipe of 60 cm length for fixing the air termination with suitable locking system as specified.
S&F in replacement of lightening conductor air termination, single pointed aluminum rod of 12 mm long including fixing of MS clamps with nuts, bolts and screws complete all as specified and directed by Engr-in-charge. Note : The PCC block shall be constructed in PCC 1:2:4 type B1 using (using 20mm grade stone aggregate) of size 200 X 200 X 200 mm including putting 15 mm dia GI medium grade pipe of 60 cm length for fixing the air termination with suitable locking system as specified.
M&L for painting to the electrical equipments, steel sections, rolling shutters etc with two coats of synthetic enamel paint with machine spray including preparation/ cleaning of the old steel surfaces exceeding 10 cm width complete all as specified and directed by the Engr-in-charge.
M&L for installation of maintenance free Chemical Earthing with copper bonded earth rod of 23.2 mm dia, 3 meter long with suitable copper plate of 250 micron welded with necessary connections clamps including 2 X 25 kg backfill chemical compound complete all as specifed directed by Engr-in-Charge. Note : The pit shall be constructed in PCC 1:2:4 type B1 using (using 20mm grade stone aggregate) RCC slab shall be provided in RCC 1:2:4 type B-1 (using 20mm grade stone aggregate) 50 mm thick pit cover reinforced with 8mm dia TMT bars 75mm c/o both ways MS handle 12mm dia with good finishig as specified.
S&F in replacement of galvanised iron strip strip of size 32 mm x 6 mm for roof conductors and down conductors above ground including PVC insulators of pasting with suitable heat resistant gum type solution complete all as specified and directed by the Engr-in-charge. Note : Any type of screw / fasteners / grouting materials are strictily not recommended by station HQ.
S&F in replacement of galvanised iron of size 25 mm x 3 mm for roof conductors and down conductors above ground including PVC insulators of pasting with suitable heat resistant gum type solution complete all as specified and directed by the Engr-in-charge. Note : Any type of screw / fasteners / grouting materials are strictily not recommended by station HQ.
Balancing the load of LT 415 Volt overhead/underground system of any bldg/feeder/panel board in any location by providing skilled tradesman & helper with necessary safety and working equipment such as clamp meter, high voltage meager tools, safety belts, hand gloves, crimping tool, other required tools and plants and rectified the unbalance load on top priority basis/as and when required including testing complete all as specified and directed by the Engr-in-charge.
Supply and laying of Electrical Insulating Rubber Mat - 11KV (1mtr x 2mtr x 2.5mm Thickness) Blue/Black Colour with IS 15652 marking on every metre with dotted anti-skid design complete all as s[ecified and directed
Supply and fix 400A AC digital clamp meter with carrying case and one pair (red, black) of comfort grip PVC insulated test leads with right-angle shrouded banana plugs for measureing AC current up to 400A including batteries and manual complete all as specified.
Supply and fix 5 in 1 Multifunctional Plier Set with 5 Interchangeable Tool Head - Wire Stripper, Crimping Plier, Cable Cutter, Electrician Scissor, Linesman Plier Kit all as specified and directed.
M&L for Mild steel duct cover of 5 mm thick chequered with 10mm dia MS bar lifting handle of required sizes including taking down the old unserviceable MS duct cover etc complete all as specified and directed by the Engr-in-charge.
Taking out old unserviceable underground cable from excavated trenches/pipes/pole complete all as specified and directed by Engr-in-Charge. Note: Necessary earth work if any required shall be measured and paid separately.
Supply, laying in trenches, duct and testing XLPE insulated (earthed) cable in screened PVC bedded galvanized steel strip armoured electric power cable (heavy duty) with stranded aluminium conductor, 1100 volts grade, cross sectional area 185 Sqmm 3.5 core conforming to IS- 7098 (Part-II) 1985 complete all as specified and directed by the Engr-in-charge.
All as per item ser No 31 here-in-above but size 70 Sqmm 3.5 Core.
All as per item ser No 31 here-in-above but size 35 Sqmm 3.5 Core.
Excavation in trenches in soft/loose soil, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep and getting out in soft/loose soil for laying of cable/foundation of pole and stay etc in complete all as specified and directed by Engr-in-charge.
M&L for sand cushioning in trenches for protection of LT underground cable including watering and consolidation as per SSR Part-I complete all as specified and directed by Engr-in-charge. Note: Punned thickness shall be measured for payment purpose.
Supply and laying well burnt sub class ‘B’ bricks, locally available of size 23x11.5x7.5 CM in trenches for protection of the underground cable complete all as specified and directed by Engr-in-charge.
Removing the excavated materials not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above ground level from starting point complete all as specified and directed by Engr-in-charge.
Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed by Engr-in-charge.
M&L complete for drilling hole under hard standing /road for laying of pipe for protection of cable etc by manual booklet without disturbing the top surface and making good the disturbed surface if any complete all as specified.
Supply and laying GI pipe light grade 80 mm bore complete all as specified and directed by Engr-in-charge.
Taking out the unserviceable MCCBs/ ACB of any type any capacity by disconnecting all electrical connections from Panel board/wall /FPB and S&F the following MCCB's with Adjustable Thermal & Adjustable Magnetic with necessary fixing arrangment, connecting and testing complete all as directed at site for the following sizes:-
160 Amps 4 Pole breaking capacity 25 kA.
250 Amps 4 Pole breaking capacity 36 kA.
400 Amps 4 Pole breaking capacity 50 kA.
630 Amps 4 Pole breaking capacity 50 kA.
Supply & Fixing in replacement battery of 12 volts capacity 150 AH complete all as specfified and directed by EIC.
Supply & Fixing in replacement battery of 12 volts capacity 180 AH complete all as specfified and directed by EIC.
S&F in replacement of onload changeover 4 pole, 200 Amps, 415 volts including taking down old unsv changeover complete all as specified and directed.
S&F in replacement of battery charger in dg set control panel of capacity 24 VDC 10 AMP including taking down old unsv charger complete all as specified and directed by Engr-in-charger.Make:- NHP / Technika or equivalent as approved by GE.
MOHIT ENTERPRISES (BID ID -3444922)
M/s Prakash Enterprises (BID ID -3444683)
M/s R P Enterprises (BID ID -3444554)
M/S Anand Enterprises (BID ID -3443564)
S K ENGINEERS AND CONTRACTOR (BID ID -3442829)
AS Engineering (BID ID -3440146)
mahadev enterprises (BID ID -3440791)
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .