SPECIAL REPAIR TO BATHROOM AND TOILET OF VARIOUS WARDS/ DEPTT OF 162 MH AT DINJAN MIL STN AND CERTAIN MINOR WORKS UNDER GE DINJAN.

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation, pipeline etc area not exceeding 10 Sqm on plan and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading in layers not exceeding 25cm, levelling, watering and well ramming as in soft/loose soil complete all as specified and as directed.

Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above starting point complete all as specified and as directed.

M&L for broken bricks hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

M&L for precast reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in cover slab of drain, etc and set in cement mortar (1:4) including necessary formwork, moulds, etc complete all as specified and as directed. Note : Reinforcement shall be measured and paid separately.

M&L for RCC (nominal mix ) type B1 1:2:4 (20 mm graded aggregate) in foundations, including rafts, footings, foundation beams ; plinth beams; bases for columns, etc ; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for RCC (nominal mix ) type B1 1:2:4 (20 mm graded aggregate) in Beams, cantilevers, bressummer, lintels over 1.5 span complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 (nominal mix) , type B-1 (Using 20 mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc complete all as specified and directed. (Note : reinforcement shall be measured and paid separately against respective item).

M&L for RCC (nominal mix ) type B1 1:2:4 (20 mm graded aggregate) in columns, pillars, piers, post and struts etc complete all as specified and directed.

S&F TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for mild steel TMT bars 6 to 8mm dia and over ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

Use and waste of form work to flat sides of cocnrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams ; and similar work ; vertical or to batter complete all as specified and directed.

Use and waste form work to flat sides of soffits of floor or roof beams, beam hauching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beam, etc complete all as specified and directed.

Use and waste form work to flat sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

S&F form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) for flat rough finished surfaces of concrete complete all as specified and directed.

M&L for plain cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete, etc complete all as specified and as directed.

Taking down the chowkhats or frames not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and as directed

Taking down the chowkhats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frames) complete all as specified and as directed

Taking down shutters of any descrption not exceeding 1.00 Sqm each and refixing in the same opening complete all as specified and directed.

S&F for solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as specified and as directed by Engr-in-Charge.

S&F 100mm size butt hinges, Extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed,type B-21 fixed in rpair and brass/bronze pin is provided in lieu of mild steel hinge pin all as specified as directed.

S&F 150mm size aluminium handle cast type anodised complete as specified and directed.

S&F for 150 mm long, aluminium barrel tower bolt, extruded section, anodised complete all as specified and as directed.

S&F for mild steel small articles using flat iron of size 25x3mm thick such as band, strap, hold fast, cleat, support, hook, hinges, base tie for door frame etc and other similar items conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

M&L for plain cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) for embedding hold fast, bed block, cills, etc including necessary form work complete all as specified and as directed.

S&F for anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified complete all as specified and as directed.

S&F 3 mm thick ordinary quality sheet glass and glazing with oil putty in square n exc 0.5 sqm in each pane as specified and as directed.

S&F 4 mm thick sheet of frosted glass ordinary quality and glazing with oil putty and steel beads in square n.exe 0.50sqm in each pane all as specified and as directed.

S&F in repair galvanised mild steel wire clothes on wooden window and door including wooden bidding 0.63 mm nominal dia of wire and average width of operturel 1.0 mm complete fixed stables all as specifed and as directed.

S&F for galvanised mild steel wire cloth of 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-16 all as speciefied and as directed.

M&L for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite including 25mm thick screed bed in CM 1:6.all as specified and as directed.

M&L for 75 mm thick, plain cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in plinth protection laid in proper slope/gradient etc, finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 75 mm thick plain cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base of floor, etc complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed or bedding layer of cement mortar in (1:6) for laying floor finishes complete all as specified and as directed

M&L for coloured glazed ceramic tiles in vertical surface of size 450X 350X 7 mm thick over 10 mm thick back coat of cement mortar in (1:4) set and jointed in neat cement slurry and pointed in white or colour cement to match over complete all as specified and as directed.

M&L for coloured glazed ceramic tiles in vertical surface of size 200X 300X 7 mm thick over 10 mm thick back coat of cement mortar in (1:4) set and jointed in neat cement slurry and pointed in white or colour cement to match over complete all as specified and as directed.

Demolition of plain cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar (1:3) with water proofing compound finished even and smooth (without using extra lime or cement in sunken floor) including prepration of plaster surfaces & applying polymer modification bituminious elastomer water proof coating for suken portion at any place , location & in any condition complete all as specified and as directed. Make : PIDILITE INDUSTRIES LTD (Dr Fixit Proof Coat) or equalent as approved. The work should have to be carried out by authorised Application of Manufacturing's as approved by GE.complete all as specified and directed. Note: Water Proofing Compound measured and paid separately.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar (1:6) including finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar (1:4) on other than fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10 mm thick in cement mortar (1:6) on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and fair without using extra cement complete all as specified and as directed.

M&L for rendering 5 mm thick in cement mortor (1:3) on concrete surfaces as in ceilings (sunshed, chajja etc) and finishing surfaces even and smooth without using extra cement complete all as specified and as directed.

Demolition of brickwork or stone/ boulder masonry, built in Cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar (1:6) complete all as specified and as directed.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar in (1:4) complete all as specified and as directed

M&L for preparing old plastered surfaces of wall, etc and applying two coats of white wash complete all as specified and as directed.

M&L for preparing newly plastered surfaces of wall, etc and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of new plastered surface of walls etc and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and as directed.

M&L for preparing old plastered surfaces of walls by washing, rubbing down and scraping of existing distempering/painted surfaces etc and applying one coat of distemper oil emulsion complete all as specified and as directed.

M&L for preparing newly plastered surfaces of internal walls, etc and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and as directed.

M&L for preparation of new wooden surface of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Supply and laying, CPVC pipe of 16mm outer dia, SDR 11 pain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

Supply and laying, CPVC pipe of 20mm outer dia, SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

Supply, laying, connection and testing, 15mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Supply, laying, connection and testing, 20mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

M&L for cutting chases, pinning in brickwalls, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 10 cm and not exceeding 20 cm girth complete all as specified and as directed.

Dismantling of water tank capacity excedding 250 Ltrs and not exceeding 500 Ltrs and removing to store complete all as specified and as directed.

S&F for 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe complete all as specified and as directed.

S&F for 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe complete all as specified and as directed.

S & F of tank adaptor ,union, ball valve 20mm bore outer dia as specified and as directed.

S&F in repair 15mm bore bib taps cast copper alloy, screwed down high pressure with crutch or butterfly handle fancy type chromium plated screwed for iron pipe for brass furule and fixed complete all as specified and directed.

S&F in repairs 15 mm bore dia cast copper alloy fancy type, chromium plated stop valves, crewed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repairs 15mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or with out lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed.

S&F in repairs soap dish, vitreous china white, approximate size 160x 160 x 90mm fixed to plugs with chromium plated brass screws complete all as specified and as directed.

S&F for 15mm bore, PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and as directed.

S&F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe providing 110mm PVC WC connector etc complete including making good to disturbed surfaces of floor to match with existing specifications complete all as specified and as directed.

S&F in repairs toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screwscomplete all as specified and as directed.

S&F in repair vitreous china wash down water closet pan white, with seat white closed pattern with flat bottom and cover mild steel chromium plated or aluminized hinging deviced including flush pipe and joint etc and connection to drain, flushing, pipe, anti-syphonage pipe, and fixing arrangements with fixing bolts etc including making good the disturbed portion of floor in cement concrete 1:2:4 type B-0, as in repairs complete all as spd & directed.

S&F for CP health faucet cast copper alloy with push button & 1m long flexible steel pipe with PVC lining suitable for 15mm bore pipe complete all as specified and directed.

S&F in repair PVC low level flushing cistern, 10 litre capacity, valveless, symphonic action type with inlet, ball valve, float and handle incl bracket, PVC conection pipe and flush pipe of polyethylene of low or high density or PVC 32 mm dia, complete all as specified and directed

S&F for PVC low level flushing cistern, 10 litre capacity, valveless, symphonic action type with inlet, ball valve, float and handle incl bracket, PVC conection pipe and flush pipe of polyethylene of low or high density or PVC 32 mm dia, complete all as specified and directed

S&F for vitreous china wash basin, size 550x400mm, white, flat back, with PVC waste pipe, CP waste coupling, chain, plug and porcelain stopper & brackets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and as directed. Make : Cat No. C0406 of Parryware/Hindware/Cera.

S&F in repairs for vitreous china bowl urinal, flat back size of 465x355x265mm whitw with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) but fixing plug bedding urinal against wall in cement mortar (1:2) securing urinal to plug including 60mm long brass screws pointing around urinal back in cement mortar including 15mm brass stop cock and waste coupling brass CP complete all as specified and as directed.

S&F in repair brass chromium plated shower rose, 125 mm size, with or without swivel joint any size incl fixing to steel pipe or union complete all as specified and as directed

S & F LDPE pipe as waste pipe 32 mm dia for wash basin all as specified and as directed.

S&F for 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

S&F for brass chromium plated tubular towel rail, D type, 60cm long, 20mm dia with brackets complete all as specified and as directed.

S&F in repair 32mm Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed

S&F for grating doom, circular type, 100mm dia of PTMT, (mimimum weigh 25 gms) complete all as specified and as directed.

S&F in repairs 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F in repairs 110 mm bore PVC (SWR) soil, waste and vent pipes single socketed, in any length with rubber ring joints laid in floors or trenches etc complete all as specified and as directed.

S&F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) bends with acces any radius complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed.

S&F for 125/110 mm bore PVC (SWR) gully trap complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) vent cowl complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) branch piece, double (double Y) equal or unequal complete all as specified and as directed.

S&F for 75mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) junction double, (double T), equal or unequal complete all as specified and as directed.

M&L for sand filling under floors or in foundation including watering and consolidating complete all as specified and directed.

M&L for salt glazed stone ware drain pipes 150 mm bore, grade 'A' laid in trenches, jointed and tested complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-2 (using 40 mm graded stone aggragate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore SGSW/RCC drain pipes complete all as specified and as directed .

M&L for water proofing treatment on RCC roof etc. comprising with the following operation & as specified herein below:- (a) Taking down existing old tarfelt, bituminous compound including cleaning & removing debris to a distance exc 100 m n.exc.250m. (b) M&L 25 thick cement concrete type B0 1:2:4( 12.5 mm graded aggregate) finished even and smooth. (c) M&L for 15 mm thick cement mortar in 1:4 finished even and smooth. (d) Preparing & cleaning of fully dried cement plastered surface. (e) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 litres per sqm conforming IS-3384. (f) A layer of APP based polymeric membrane membrane 3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyster non woven fabric (weighing not less than 160 gms/sqm) shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction. (g) One coat of aluminium paint over APP membrane @0.11Kg/Sqm. Note:- Prior to execution of the APP Membrane works, leak proof test shall be done by ponding water on roof slab to minimum depth of 25 mm. The entire roof slab shall be flooded with water for 48 hours. The necessary barrier shall be made to make feasible to stagnate water for 48 hours on roof slab.

M & L for Brass CP mixer for mixing hot & cold water screwed down for CPVC pipe and fixed all as specified and as directed.

S & F Parryware Omega Soap Dispenser mount on wall as specified and as directed.

S&F Parryware wall Mixer 3-in-1 all as specified and as directed. (Cat Part No G0617A1)

S & F Parryware Corner shelf (Cat Part No T6010A1) as specified and as directed.

S&F Parryware Single piece white colour EWC Size 620x350x725mm as specified and directed. ( Cat Part No C8852)

Supply and fixed new Magnum parryware urinal port (combo set) size 590x400 catpart No C0583 including spreader all as specified and directed.

S&F Parryware Towel Ring all as specified and directed. (Cat Part No T6402A1)

S&F Parryware counter top basin size 550x445x200mm white colour all as specified and director.

S&F Parryware counter down basin size 550x445x200mm white colour all as specified and director.

S&F Parryware 15mm dia Two way Bib cock all as specified and directed.(Cat Part No G5234A1)

S & F 5-6 mm thick looking glass Mirror Exc 1.5 Sqm and n.exc 2 Sqm including all fitting and fixturing stainless steel fitting all as per specified and as directed by Eng-in-charge.

Taking down carefully aluminium/copper point wiring (light, fan, socket or power) including unserviceable light fittings, switch board complete, switch sockets, ceiling roses, pendants, regulators, sockets, etc and removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

M&L for point wiring with 1.5 Sqmm (nominal area), FRLSH PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including PVC casing caping/PVC conduit with all fittings and accessories of PVC casing caping (like Tee, bend etc.) complete fixed to walls /ceiling etc. with and including 1.5 Sqmm (nominal area) FRLSH PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point including PVC terminal box (sunken type) with 3mm thick hylam sheet cover fixed with suitable sizes cadmium plated iron screws and washers etc. for mounting switches, sockets, fan regulators etc complete for one light/ fan /bell /buzzer point controlled by one, one way switches complete all as specified and as directed. Note:- Necessary Cutting chasing shall be included in quoted rate.

All as per item No 02 above but for one 3 pin 5 Amps, socket outlet, on Independent board.

All as per item No 02 above but for one 5 Amps, 3 pin socket outlet on the same board with other switches.

All as per item No. 02 above but wiring with cables of size 2.5 sqmm & cables of size 2.5 sqmm as continuous earth wire for one 15/16 amp multi socket out let on independent board.

S&F for switch piano, flush type single pole, 230 volts, 5 Amp one way bearing ISI marked complete all as specified and as directed.

S&F for switch socket combination, 2 in 1, 5 Amps, flush type, 240 volts bearing ISI marked complete all as specified and as directed.

S&F for ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body bearing ISI marked and including PVC box complete all as specified and as directed.

S & F modular switch 6 Amps 240 V,single pole , one way,flush type and connecting up complete all as specified and as directed.Make:- Legrand Cat Part NO 573400 or equivalent.

S & F modular socket multi purpose ( ISI marked), 2 pin and 3 pin 5 Amps , 240 V , flush type, controlled by one switch and connecting up complete all as specified and as directed . Make: Legrand or equivalent

S & F Modular switch socket combination multipurpose (ISI marked), 2 pin and 3 pin 5 Amps , 240 V , flush type, controlled by one switch and connecting up complete all as specified and as directed . Make: Legrand Cat Part No. 573542 or equivalent.

S & F modular switch socket combination multi purpose ( ISI marked),one 3 pin 16 Amps and 3 pin 5 Amps , 240 V , flush type, controlled by one switch and connecting up complete all as specified and as directed . Make: Legrand or equivalent

Supply and fixing the following white cover plate and frame for modular switches.

Two module complete all as specified and directed.

Three module complete all as specified and directed.

Four module make complete all as specified and directed.

Six module complete all as specified and directed.

Supply and fixing metal flush box suitable for modular switches complete all as specified and directed

Two module complete all as specified and directed.

Three module complete all as specified and directed.

Four module make complete all as specified and directed.

Six module complete all as specified and directed.

Supply and fixing Bulb angular/batten holder PVC/Polycarbonate suitable for batten fittings including one No LED Lamp of 9W of Havells/Philips/Cromton Make, complete all as specified/directed.

Taking down old tube light and S&F new 9 W surface mounted Corona type round downlighter for soft diffuser lighting colour temperature is 6000K complete all as specified and directed by Engr-in charge.

S&F for 20 Watt surface and wall mounting type LED batten with polycarbonate housing & integrated complete all as specified and as directed.

S&F for 25 Watt LED building security light new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embeded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07 including all fixing arrangement and taking down old light fittings of any type complete all as specified and as directed.

S&F for sheet metal enclosure TPN board distribution (DB) having facility to fix MCCB in incomer and MCBs in outgoing, TPN 4 ways, IP-43 with metal door type complete fitted with bus bars , neutral links, blanking plates including making dgood disturb surface, including taking down old unserviceble MCB DB complete all as specified and as directed. Make: Legrand, Cat Pt No. 607913 or equivalent make of Appendix 'A'.

S&F in replacement of MCCB, 4 pole, 415 V with adjustable thermal & adjustable magnetic setting, 160 Amps of breaking capacity 25 KA complete all as specified and as directed.

S&F for factory made board distribution (DB) double door in sheet metal enclosure with common bus bar at incomming end, single pole & neutral, 8 way, 240 Volts suitable for housing MCBs including complete all as specified and as directed.

Supply and fixing in repair of MCB Distribution board SPN 4 Way for mounting SPN/ SP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed by Engr-in-charge.

Supply & fix of MCB double pole 6-32 Amps, 'C' Series 10 KA 240 volts complete all as specified and directed.

Supply & fix of MCB SP 6-32 Amps, 'C' Series 10 KA, 240 volts complete all as specified and directed.

Material and labour for earthing complete with galvanised steel earth plate electrode of size 600 x 600 x 6 mm thick, burried directly in ground (earth pit not less than 2.25 m below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanised wire of dia 4 mm as earthing lead by means of nuts, bolts and washers of galvanised iron and earth lead protected by galvanised iron pipe 15 mm bore (light grade) and connected to earth test point and including cement concrete pit in PCC (1:3:6) type C-1(using 20 mm graded aggregate) and pre-cast RCC cover slab of size 540 x 540 x 50 mm thick, reinforced with 8 mm dia TMT bars both ways and one handle for lifting made with 10 mm dia mild steel bar,funnel, wire mesh 20 mm bore galvanised (light grade) for watering, charcoal and salt in alternate layers including necessary execuation and eath works in any types of soil complete all as shown on Electrical plate No 3 of MES SSR-I including taking out the old earthing material complete all as specified and directed. Note:No extra payment will be for the earthing GI wire of size 4 mm dia

Taking down unserviceable sub-main wiring up to 10 sqmm with rigid steel conduits/PVC casing-caping including cutting chases for taking out conduits and making good disturbed surfaces complete all as specified and as directed.

M&L for sub main wiring with two run of 10 Sqmm (Nominal area) single core cable PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC casing-caping/conduit of suitable size, fixed to wall/ceiling etc including one run of 10 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor (FRLSH) as earth wire and duly connected to common earth point complete all as specified and as directed. Note : (a) PVC Casing-caping/conduit, two run wiring cables and one run of earth wire will be measured as one length (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets. Note:- Necessary Cutting chasing shall be included in quoted rate.

M&L for sub main wiring with two run of 6 Sqmm (Nominal area) single core cable PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC casing-caping/conduit of suitable size, fixed to wall/ceiling etc including one run of 6 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor (FRLSH) as earth wire and duly connected to common earth point complete all as specified and as directed. Note : (a) PVC Casing-caping/conduit, two run wiring cables and one run of earth wire will be measured as one length (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets. Note:- Necessary Cutting chasing shall be included in quoted rate.

M&L for sub main wiring with two run of 4 Sqmm (Nominal area) single core cable PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC casing-caping/conduit of suitable size, fixed to wall/ceiling etc including one run of 4 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor (FRLSH) as earth wire and duly connected to common earth point complete all as specified and as directed. Note : (a) PVC Casing-caping/conduit, two run wiring cables and one run of earth wire will be measured as one length. (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets. Note:- Necessary Cutting chasing shall be included in quoted rate.

S&F in repair PVC casing caping of size 20-25mm complete all as specified and as directed.

Supply, Laying and testing cable LT XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade, laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including brass cable glands,clamps,etc of 2 core 16 sqmm. Note : (1) Pipes shall be measured and paid separately under relevant items of this schedule. (2) Excvation and earth work shall be measured and paid seperately.

Supply, Laying and testing cable LT XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade, laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including brass cable glands,clamps,etc of 3.5 core 50 sqmm. Note : (1) Pipes shall be measured and paid separately under relevant items of this schedule. (2) Excvation and earth work shall be measured and paid seperately.

M&L for sand cushioning with dry clean sand 15cm below cable and 8cm above the cable complete all as specified and as directed. Note : Punned thickness shall be measured for payments.

Material & Labour for common burnt clay building bricks (locally available best quality), sub-class ‘B’ designation 75 of suitable size available in market to cover LT underground cables, laid dry and flat abutting each other with gaps not exceeding 10mm including taking down old unserviceable bricks complete all as specified and directed.

Supply and Fix Exhaust fans AC Single phase 230/240 Volts of size 300 mm sweep with Louver complete all as specified and directed.

M&L for test point terminal box made of gun metal or phosphorous bronze, size 75x75x25 mm drilled and screwd including 3 Nos 8 mm dia 25 mm long hexagonal head screw incl taking down old unserviceable complete all as specified and as directed.

Supply & fix exhaust fans metallic body AC single phase 230/240V of size 300mm sweep with louver complete all as specified and directed.

M&L for cutting of circular hole at any type of wall suitable size for fixing of exhaust fan of size 300mm sweep, grouting 04 Nos 100mm long 12mm dia stud bolt including,making good to disturbed surfaces of wall and colour wash to match as per the existing colour complete as directed and specified by engineer-in-charge.

S&F street light bracket fabricated out of GI Tubing light grade 32 mm bore Bend to the shape as directed and of length 1.5 mtr complete with mounting MS clamp of flat iron size 40X5mm of suitable length 02 pairs incl nut bolts etc of suitable size, including taking down old corroded one all as specified and directed.

M&L for 32 mm bore, steel tubes, galvanised, light grade with all fittings, laid in floor/road crossing/drain etc as in UG cable protection complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply and lay 3 layer ( inner antimicrobial, outer UV stabilized) ISI marked,IS-15801 ,PP-R pipes SDR 7.4 (PN-16) and PP-R plain plain and brass threaded fittings laid in concealed work complete of size outer dia 25 mm

Supply and fix PPR Gate Valves (Brass Insert) of 25 mm bore.

M&L for Cutting existing pipe of any size for inserting of TEE for connection of PPR pipe of 32mm dia complete all as directed.

M/s. R. K. Trading Company

R.D.CONSTRUCTION

M/S HAZARIKA CONSTRUCTION

FREEZCON

M/s GANDHESWAR PHUKAN

STANDARD ELECTRIC WINDERS

Construction House