SPL REPAIR TO MT GARAGE BLDG NO P-170, P-171, P-172 AND BLDG NO T-222 (CK HOUSE AT OLD HORN LINE) UNDER GE (EAST) MATHURA

Amount

Taking down Chowkhats or frames not exc. 1.5 sq m each with shutters (without taking off shutters from the frames), complete all as specified & directed.

Taking down Chowkhats or frames exc 1.5 sqm but n exc 4 sqm each with shutters (without taking off shutters from the frames), complete all as specified & directed.

S&F Pressed steel frame for doors of size 125 X 60 mm frabicated out & 1.25 mm thick sheet with one or more rebates including necessary fixing lungs, hinges, lock strike plate, etc, supplied and fixed complete all as specified and as directed.

S&F Pressed steel frame for doors of size 105 X 60 mm fabricated out & 1.25 mm thick sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, supplied and fixed complete all as specified and as directed.

M&L for PCC 1:3:6 type C-0 (using 12.5 mm graded stone aggregate) as in filling of pressed steel frame complete.

M & L for 35mm thick flush shutters, solid core construction with block board core and veenerd face fixed on both side of door, coloured as approved by GE, including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

S&F 35mm thick plain framed paneled shutters, any No. of panels with panels of plywood 9mm thick for two or more panel construction and 12mm for single panel construction, BWR conforming to IS fixed to timber frame of 2nd class hard wood, all style & rail are as per clause 8.24(a) of SSR Part – I all as specified and directed by Engineer- in-Charge .

S&F 35 mm thick factory made second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and as directed.

S&F Factory made single extruded WPC (wood polymer composite) solid door/window/ceosetory windows & other frames/chowkkat of size 45x85 mm comprising of virgin polymer of K value 58-60 (suspension grade), calcium caronate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mmiter joints after applying PVC solvent cement and screwed with full dody threaded star headed SS screws having minimum density of 650 kg/cum nd screw withdrawal strength of 2200 N (face) & 1100 N (Edge), minimum compressive strength 58 N/mm2 , modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category of being termite / borer proof, water / moiture proof and fire retardant and fixed in positin with suitable MS hold fast /lugs/SS dash fasteners f required dia and length complete, all as per direction of engr-in-charge complete all as directed

S&F Factory made single extruded WPC (wood polymer composite) solid plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (suspension grade), calcium caronate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum nd screw withdrawal strength of 1800 N (face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , odulus of elasticity 850 N/mm2 and resistance to spread of flame of class A category of being termite / borer proof, water / moiture proof and fire retardant and fixing with stainless steel butt hinges of required ie with necessary full body threaded star headed counter sunk SS screws, all as per direction of engr-in-charge complete all as directed

S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/cupboard Chowkhat of size 45 x 70 mm having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length, complete all as specified & directed.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded sections, complete all as specified & directed.

S&F 150 mm long aluminium handles, fabricated, cast type, complete all as specified & directed.

S&F 100 mm long Stainless steel, but hinges, type B-21, complete all as specified & directed.

S&F 250 mm long aluminium alloy sliding door bolt , bolt type and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

S&F aluminium anodised hasp and staple 100 mm long, including bolt to hinge plate and fixed with screws, complete all as specified and directed.

S&F Aluminium floor door stopper 2 legs runner shoes at and 150mm long, complete all as specified and directed.

S&F powder coated (minimum thickness and powder coating 50 micron) aluminium frame for doors, windows, ventilators etc with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

M&L for Powder coated aluminium frame (minimum thickness of powder coating 50 micron) work for shutter of doors, windows, ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (fittings shall be paid for separately) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gask etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/stainless steel screws complete all as specified and as directed.

S&F aluminium decogrill of approved design made out mesh size not exc 50mmx50mm fixed to the window frame with CP brass /stainless steel screws including cutting and fixed with f channel/u channel all as specified and directed

S&F double action floor spring hydraulically regulated made of aluminium 1.25mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass, other parts made of mild steel heavy duty.including fixing of broken tile.

S&F Pre-coated coloured 200mm long plate type, springs including roller and roller plate complete all as specified and directed.

S&F aluminium extruded section door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified & directed.

S&F Factory made steel windows with side hung shutters including projecting type hinges with steel handle & steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F Factory made steel windows with side hung shutters including projecting type hinges with steel handle & steel peg stay complete with out glazing bars, dovetailed or welded complete all as specified and as directed.

S&F mild steel ventilator with top hung shutter incl hinges, steel peg stay complete incl one shop coat of zinc chormate primer.

S&F for steel wire fabric welded steel wire fabric weight n.exc 4.0 kg/sqm fixed on to wood or steel members complete all as specified & directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or stainless steel wire staples, complete all as specified & directed.

S&F 4.8 mm thick Sheet glass, ordinary quality and glazing fixed to aluminium/ Steel/ wooden frame with rubber beading/ putty/ wooden beading as required area exc 0.5 sq. m in each pane complete all as specified and directed.

S&F for 4.0 mm thick sheet glass in squares n exc. 0.5 sqm each pane including rubber bead jointing cleat for fixing in position for aluminium window/ventilator all as specified and directed.

S&F 4.0 mm thick Figured glass, pin head type and glazing with rubber beading/ putty/ wooden beading as required in squares n exc 0.5 sq. m in each pane fixed with ventilator shuttter complete all as specified & directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thick, including removing rubbish out side of MoD land, complete all as specified & directed.

Dismantling floor hearth and wall tiling including cement mortar bedding (but not backing) and rubbish off the premishes.

M&L for Non skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM 1:4, complete, all as specified and as directed.

M&L for Coloured Glazed ceramic tiles in vertical surface 600x300x7mm thick including highlighter tile ap approved and directed set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10mm thick screed plaster in cement mortar (1:4) complete all as specified & directed.

M&L for Coloured Glazed ceramic tiles in vertical surface 450x350x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10mm thick plaster in cement mortar (1:4) complete all as specified & directed.

M&L for Non skid Ceramic coloured tiles 7-8 mm thick (square/ rectangular) area of each tiles exc 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified & directed.

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm as in vertical surface like dado or skirting over & including10mm thick in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L for coloured Ceramic tiles 10 mm thick (square/ rectagular) polished, area of each tiles exceeding 0. 36 sqm but n exc 0.72 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in cement motar 1:4 and grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10) kg of hardener and 0.20 kg of resin per kg) including fillling/grouting and finishing complete all as specified & directed.

S&F in repair 5mm thick solid PVC wall lining single side prelam inclusive of solvent cement and fixing at site on including necessary frame work of 5 mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall complete all as directed by Engr in charge.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded and pointed in any mortar including removing rubbish out of the MoD land, complete all as specified & directed.

M&L in repair for 18-20 mm thick Black granite stone as in cooking platforms , slabs for oval type WHB,sinks etc & the likes complete laid over 15 mm thick cement sand screed in CM 1:4 incl mirror polishing complete & providing necessary holes for gas pipe / water supply pipes etc .

M&L for 18-20mm thick Green marble (of any type) work (table rubbed and polished) for Shelves (veneering to wall) including 15mm thick plaster in cement mortar (1:4) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified & directed.

M&L for 4-5 cm thick machine cut sand stone slab in sun shades, chajjas, shelves, cills, landings, cover stones, templates, etc., n. exc. 2 m in length, set and pointed in CM 1:4, complete all as directed.

Providing edging moulding to 18-20 mm th stone of counters etc including machine polishing to edge to give gloss finish complete all as specified & directed.

M&L for Machine cut kota stone slab as in flooring /one piece as in steps of stair case flooring 20-25mm thick over and including 15 mm thick screed bed in CM 1: 4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & directed.

M&L for Kota stone slab 18-20mm thick ( One piece) in riser of steps, skirting, dado and including pillar laid over and including 10mm thick backing coat in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of slab including making groove to curve skidness, rubbing and polishing complete all as specified & directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over 20 mm thick screed bed in CM 1:3 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all specified and directed.

M&L for Kota stone slab 18-20mm thick ( One piece) in riser of steps, skirting, dado and including pillar laid over and including 10mm thick backing coat in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of slab including making groove to curve skidness, rubbing and polishing complete all as specified & directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work including removing rubbish out of MoD land, complete all as specified & directed.

M&L for reinforced cement concret nominal mix, (using 20mm graded stone aggregate) as in slab supported on wall and shelves etc complete all as specified & directed.

M&L for MS TMT bars 10 mm dia and over, cut to length bent to shape required incl cranking bending ,spirally for hooping for column ,hooking ends and binding with and including MS wire annealed not less than 0.9mm dia, complete all as specified & directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), complete all as specified & directed.

Form work to edges of concrete flat, roof slabs ,concrete railings, breaks in floors and similar works not exceeding 100 mm wide for fair finished surfaces, complete all as specified & directed.

Demolition of Brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete, all as specified & directed.

M&L for brick work with fly ash old size bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6, complete, all as specified & directed.

M&L for brickwork with fly ash, old size bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified & directed.

Taking down cement plaster on brick or stone walls,ceiling etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for rendering 15mm thick on other than fair faces of brick work or stone masonry surfaces in cement plaster 1:4 mixed with water proofing compound as per manufacturer's instruction, finished even and fair on wall surfaces, complete, all as specified and directed .

M&L for 15mm thick rendering in two layer on stone masonry surfaces or surfaces other than fair face of brick work of walls consisting of 1st layer of 10mm thick plaster in CM 1:4 and 2nd layer (setting coat or top layer) of 5 mm thick plaster in CM 1:4 mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished fair & even, complete, all as specified and directed. Note : - Supply only water proofing compound shall be measured and paid for separately.

Supply only Liquid water proofing compound complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick or concrete surfaces in CM 1:6, finished even and fair complete, all as specified and directed

M&L for rendering 10 mm thick on concrete surfaces in ceiling in cement mortar 1:3, finished even and smooth without using extra cement, complete all as specified & directed.

M&L rendering 10 mm thick on ceiling surfaces in CM 1:3 finished even and fair all as specified

M & L for preparation of surface and applying two coats of 100% premium acrylic exterior emulsion paint having VOC less than 50 gm/litre & excellent protection against UV, Alkali & Fungal resistance, exterior paint of required shade (Company Depot tinted) with silicon additives @ 1.43 litre/10 Sqm over and including 2 mm thick wall care putty and priming coat of exterior primer applied at 0.90 litre/10 Sqm over new surfaces upto tripple storey with fully utomatic airless spray machine of paint application having an electric motor of min 1 HP with a flow speed of min 1 ltr per min having pressure 3300 PSI. Allow 6-8 hours to dry the surface of both coat of paint to achieve excellent application with 5 years perfomance warranty from manufacturers and instruction complete using limited man power including scaffolding, trestles, ladders, cradles and necessary safety measures for upto triple storey buildings, complete all as specified and directed. Note : (a) Complete work to be executed by authorised applicator from paint manufacturer. (b) Primer and emulsion application to be carried out through air less spray machine or by roller (only mechanical application allowed except in paint application on bands/chajja & building edges/ borders/projections where contrasting colour as specified and directed is to be applied)

M & L for preparation of old surface including complete removal and applying two coats of 100% premium acrylic exterior emulsion paint having VOC less than 50 gm/litre & excellent protection against UV, Alkali & Fungal resistance, exterior paint of required shade (Company Depot tinted) with silicon additives @ 1.43 litre/10 Sqm over 2 mm thick wall care putty and including priming coat of exterior primer applied at 0.90 litre/10 Sqm over new surfaces upto tripple storey with fully utomatic airless spray machine of paint application having an electric motor of min 1 HP with a flow speed of min 1 ltr per min having pressure 3300 PSI. Allow 6-8 hours to dry the surface of both coat of paint to achieve excellent application with 5 years perfomance warranty from manufacturers and instruction complete using limited man power including scaffolding, trestles, ladders, cradles and necessary safety measures for upto triple storey buildings, complete all as specified and directed. Note : (a) Complete work to be executed by authorised applicator from paint manufacturer. (b) Primer and emulsion application to be carried out through air less spray machine or by roller (only mechanical application allowed except in paint application on bands/chajja & building edges/ borders/projections where contrasting colour as specified and directed is to be applied)

M & L for applying Two coats of Premium acrylic emulsion paint having Alkali & fungal esistance, dirt resistance exterior paint of required shade (Company Depot Tinted) over and including a coat of exterior primer applied over old surface including complete removal of existing treatment and spray machine/roller, spray hard to receive area to achieve excellent application using limited manpower including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M & L for applying two coat of Oil bound distemper over a coat of primer & over a coat of 2 mm thick wall care putty on newly plastered surface using airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr.The machine should should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper shold be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed.

M & L for complete removal of existing surface and applying two coat of Oil bound distemper over a coat of primer & over a coat of 2 mm thick wall care putty on old plastered surface using airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr.The machine should should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper shold be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed.

M&L for applying three coats of white wash on newly plastered wall surface complete all as specified and directed.

M&L for applying three coats of white wash on old wall surface including , removal of existing treatment of old wall complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying two coats of white wash complete all as specified and as directed.

M&L for two coats of white wash on ceiling including preparation of old plaster surface complete.

M&L for three coats of white wash on ceiling including preparation of new plastered surfaces, complete all as specified and as directed.

M&L for complete removal of existing treatment on ceiling and applying three coats of white wash complete all as specified & directed.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide or zinc chrome primer complete all as specified & directed.

M&L for applying a coat of synthetic enamel paint on old painted steel surfaces of any description not other wise describe, over 10cm width or girth complete all as specified & directed.

M&L for prepration of new wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for 50mm thick Cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate laid in panels not exc 3 m and providing grooves at corner finished cement concrete surface even and fair without using extra cement as in plinth protection laid in panels, complete all as specified & directed.

Dismantling of Wall & ceiling boards (fiber, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets

M&L for 4 mm thick prepainted and designer type E-board in false ceiling (flat or sloping) fixed to and including powder coated MS snap grid frame size of grid 605 x 605 mm, 4 mm GI wire for hanging and including 10 mm wide disginer POP strip all round at the junction of wall and false ceiling complete all as specified and as directed by Engg.-in-charge.

Taking down carefully cement concrete /spalled out concrete from RCC roof projections, ceiling ,sunsheds, beams, etc upto cover depth by chipping out lightly including necessary scafolding etc complete.

M&L for Cleaning the existing reinf of slabs , chajjas etc & applying a coat of SIKA RUSTOFF 11 to remove the loose rust particles etc & throughly cleaning the surface,complete all as specified and as directed.

M&L for applying a coat of bond coat made with cement slurry (1 part cement to 1.5 -2 parts water) mixed with admixture mixed @5 Kg per 50 kg of cement & applying to the conc surfaces @ 200 gm/sqm to obtain tack.

M&L for 15mm thick rendering in CM 1:1:2 using1 part of cement 1 part 2-3 mm screenings of stone agg & 2 parts coarse sand ofover the bond coat applied surfaces with cement mixed with admixture @ 100 gm /50kg of cement & finishing the surface even & rough to receive final rendering coat.

M&L for rendering 5 mm thick on concrete surfaces in ceiling in cement mortar 1:3, finished even and smooth without using extra cement, complete all as specified & directed.

Dismantling PCC tiles / brick tiles or terracing tiles, single layer on roofs laid bedded and pointed in any mortar complete all as specified and directed

Demolition of roof treatment any thickness including PCC , Mud phuska PCC padding, plastering , APP membrane complete treatment and in any position and removing the demolished material out of MoD land complete all as specified and directed.

M&L for 40 mm average thick PCC 1:2:4 type B0 (using 12.5mm grd stone agg) in floors/padding for levelling of roof surface and finishing the surface even and fair with out using extra cement, complete, all as specified and directed.

M&L for APP based polymeric membrane not less than 3 mm thick, weighing not less then 3 kg / Sqm, reinforeced with polyster non-woven fabric (weighing not less than 150 gm/sqm). It shall be laid by torch application. Side overlaps shall be 75 mm and the ends shall be 100 mm and all overlaps and jointed shall also be sealed by torch application. For parapets, membrane shall be taken to a height of minimum 60cm and then inserted inside the parapet in a groove and same shall be flashed by membrane flashing. Complete APP membrane (in roof/parapet surfaces) shall be laid over and including a coat of cold applied bituminous primer confirming to IS:3384 @ 0.40 Kg per Sqm, complete all as specified & directed.

M &L for Cement concrete plain tiles 25cm x 25cm x 22mm thick, machine pressed; set jointed and pointed in neat cement slurry, laid over and including 15mm screed bedding layer in CM 1:4 and filling the 2mm wide joints of tiles with cementitious grouting material complete all as specified & directed.

S&F in repair curtain rod stainless steel chromium plated 22-25 mm dia with bracket knobs including decorative finials all as approved complete all as specified and directed.

S&F in repair curtain rod stainless steel chromium plated 20mm dia with bracket knobs including end cap complete all as specified and directed.

Taking up or down steel tubing and connections, 15 mm bore complete all as specified and directed.

Taking up or down steel tubing and connections, 20 mm bore complete all as specified and directed.

Supply and laying of 20mm CPVC pipes outer dia, SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S&F 15 mm bore of pipe GI medium grade steel tubes, galvanised with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F 20 mm bore of pipe GI medium grade steel tubes, galvanised with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

M&L for Cutting chases, pinning in, making good to facing where required & pointing in CM 1:3 to ends or edges of landings ,steps cill sunshade ,shelves ,lintel , concealed water tubing and like not exc 10CM girth in brick wall

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

Supply and laying of 75 mm dia PVC pipes SWR fittings on walls / ceiling or laying in floors complete all as specified.

Supply and laying of 110 mm dia PVC pipes SWR fittings on walls / ceiling or laying in floors complete all as specified.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F 75 mm bore PVC bends any radius /branch piece/ tee all as directed

S&F 110 mm bore PVC bends any radius /branch piece/ tee all as directed

S&F 110mm bore PVC (SWR) vent cowl

S&F 75mm outlet dia bore PVC (SWR) floor trap plain with grating including jointing with solvent cement

S&F in repair for 75 mm bore Cast iron Nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed.

S&F in repair Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including 'P' trap setting the trap and pan in concrete and including 10 ltr capacity PVC valveless syphonic action type low level flushing cistern having dual control flushing system and 32mm dia PVC Flush pipe complete including jointing to socket of flushing rim, complete all as specified and directed.

S&F in repair for wall hung vitreous china wash hand basin white flat back size 550 x 400 mm including pedestal, bracket including all suitable fixing arrangements, complete all as specified and directed.

Supply only 32mm waste coupling fittings, PTMT for basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, , complete all as specified and directed.

S&F in repair bib taps long body cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipes complete all as specified and as directed.

S&F in repair Stop Valve/ angular cock cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipes complete all as specified and as directed.

S&F in repair Pillar taps, wt not less than 650 gm, fancy type, long body, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for 15mm bore dia iron pipe complete all as specified and as directed.

Supply only pillar tap 15mm bore cast copper alloy with fancy type , chromium plated screwed down high pressure long screwed shank and fly nuts for iron pipe all as specified and directed.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with stainless steel bracket guard & railing 60cm long complete all as specified and as directed.

S&F in repair Brass chromium plated tubular towel rail 20 mm dia type D 600mm long between flanges fixed to wall complete all as specified.

S&F PVC connection 15mm size best quality with PTMT nuts 450mm long.

S&F in repairs Stainless steel sink made out of 1.0 mm thick sheet for kitchen or laboratory with plugs washers ,waste etc and incl fixing in granite plateform complete and making good to the side of wall,connecting union to pipe, Overall size 495mmx420mm and bowl size 410x330x160mm complete all as specified and directed

M&L for 40 mm waste fittings, brass, chromium plated for sinks / basin, with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as directed.

Supply only 32 / 40 mm waste fittings, brass, chromium plated for sinks / basin, with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as directed.

S&F 32mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 and fittings, fixed to WHB, complete all as directed.

Dismantling old water tanks exc 500 & n exc 1000ltrs capacity and removing all as directed

S&F 1000 Litre capacity rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top), WHITE COLOUR, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & wash out pipe required dia of GI pipe, etc including tank cover, tank nipple etc complete as specified in SSR Part-I.

S&F Rotational moulded polythelene water tanks white colour triple layers (cylindrical vertical with closed top) hoisted and fixed in position for 750 litres. Storage capacity complete all as specified and directed

S&F in repair Gun metal, globe or gate valves 20 mm bore dia, with iron wheel head, screwed both ends for iron pipe and fixed all as specified

S&F 20mm bore ball brass valve high pressure with brass rod Polythene float and fly nut complete screwed for iron pipe and fixed all as specified.

S&F 25 mm bore ball brass valve high pressure with brass rod Polythene float and fly nut complete screwed for iron pipe and fixed all as specified & directed.

S&F 20mm bore GI nipple suitable for HDPE water tank.

M&L for precast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in manhole cover slab shelves & similar article with plain fair faces and set in cement mortar 1:4 complete all as specified and directed

M&L for P.C.C 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in coping or roof kerbs on roof chamfered on edge including troating slightly complete all as specified and as directed.

S&F 18mm thick WPC board in cupboard shutter/kitchen cabinet with decorative laminated on one side & other side balancing white, fixed with necessary stainless steel drilling screws/Anchoring bolt along with modular handles, design and colour as approved by GE including dismantling of boards any type, complete all as specified and directed. Make: Rajshri/ GIZA/ Black Cobra

S&F 18 mm thick WPC board in cupboard shutter/kitchen cabinet with both side balancing white fixed with necessary stainless steel drilling screws/Anchoring bolt along with modular handles, design and colour as approved by GE including dismantling of boards any type, complete all as specified and directed. Make: Rajshri / GIZA/ Black Cobra

S&F Continuous (piano) hinges width of flaps 30 mm (when opened) mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F 0 degree clip type self closing hinges for cabinets fixed with cadimum coated screws all as per sample.

S&F magnetic catches for cabinets of size 50 mm complete with striking plate & magnetic stud complete all as per approved smaple.

S&F stainless steel handles 100 mm size for kitchen cabinet, cupboard shutters, pattern/design as approved by GE.

Dismentling timber scantlings 40 sq cm and over in section, in any position

M&L for roof trusses (Framed) tubular truss, crane gantries, rails and fastenings and heavy brackets framing (Hollow tubular section, beam, tee, angle, channel or flat section) FE-290 Gd-165 including distance pieces, cleats etc complete all as specified and directed

Dismantling asbestos cement (corrugated, semi-corrugated, etc., ) sheets in roof covering complete all as specified and directed by Engineer-in-Charge.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of sheet complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate as in sub base, complete, all as specified and directed by Engr-In-Charge.

Supply and laying 60mm thick factory made chamfered edge cement concrete interlocking paver block of M-35 grade confirming to IS 15658-2006 with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over minimum 50 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. complete, all as specified and directed by Engr-In-Charge.

Taking down carefully aluminum/copper point wiring (light ,fan, socket any type, power, bell etc. ) complete including fixtureS&Fittings (such as ceiling rose, socket, Pendent, regulator, light fittings etc) and removing the material from site and making good the disturbed surfaces of walls ceiling etc complete all as directed. (Note: Credit for above items should be made as per credit Schedule separately)

Taking down carefully by submain wiring of any type complete and making good disturbed sufaces to match with the existing surfaces all as directed by Engineer-in-Charge.

Taking down old unserviceable existing SPN/TPN DBs / enclousers any size and type / any descriptions as iron sheet scrap including MCB any type / size and making good disturbed surface / wall as per existing complete all as specified and directed

M & L for Point wiring for One light/ fan point controlled by one way switch 5 amp with 1.5 Sqmm (nominal area) single core PVC insulated unsheathed (FRLS) cable, multi-stranded, 1100 volts grade copper conductor, in universal colour code with & including suitable size of rigid non-metallic PVC conduit (not less then 20mm dia med gd) and its all accessories complete concealed in wall/roof incl cutting & chases (making good all to the disturbed surfaces as per existing) including with modular flush metal boxes with modular cover plateS&Frame for mounting modular switches, sockets, regulators etc and including earth wire of PVC insulated (FRLS) copper conductor multistranded of 1.5 Sqmm size in green colour complete all as specified in current SSR Part-I & II & directed by the Engineer-in-Charge as described below:-

All as per item No. 152 but for One 3 pin 5 Amps socket point controlled by one way switch on same board.

All as per item No. 152 but for One 3 pin 5 Amps socket point controlled by one way switch on independent board.

All as per item No. 152 but for 3 pin / 5 pin 16 Amps sockets outlet with 4 Sqmm PVC insulated & unsheathed (FRLS) copper conductor cable independent Point wiring complete all as specified and as directed .

S&F in repair ceiling rose, PVC / Polycarbonate, isolated body 65mm x 50mm three terminals complete.

S&F Modular switch 6 Amps single pole one-way, 1 Module complete.

S&F Modular switch 16 Amps single pole one-way, 1 Module complete all as specified.

S&F Modular socket 2-in-1, 5 pins 6 Amps, combined 2 Module complete.

S&F Modular socket 2-in-1,3 and 5 pins 6 /16 Amps, combined 2 Module complete.

S&F switch piano, flush type, 5 Amps single pole one-way complete.

S&F switch piano, flush type, 15 Amp single pole one way complete all as specified.

S&F socket outlet, flush type, 2-in-1, 5 pins 5 Amps complete.

S&F socket outlet, flush type, 2-in-1, 3 pins 5 /15 Amps complete.

S&F stepped type electronic fan reglator, flush type, on existing phenolic laminated sheet etc complete all as specified.

S&F lamp holder, PVC / polycarbonate type with back plate suitable for batten.

Supply & fixing indoor decorative ultra slim surface /Wall mounted LED batten tube light complete fitting 1x 20 watt LED Tube fitting with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts, co- related colour temperature (CCT) of 6500K, >100 Lm/Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

Supply & fixing indoor decorative ultra slim surface /Wall mounted T5 LED batten tube light complete fitting 1x10 watt LED Tube fitting (size within 600x25x40 mm) suitable for mirror light with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K,>100Lm/Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED 9W suitable for normal holder (Base Cap B22) complete all as specified.

Supply and install of 30 / 35 W LED building security light fitting with lens & driver, powder coated pressure die cast aluminium, top opening and maintainable with heat resistance toughened glass, built-in Short-Circuit Protection, Over voltage Protection and Surge Protection, IP-65 proction with luminaire efficiecy of greater than 80Lumen/Watt, Colour rendering (CRI) of ≥ 70 and co- related colour temperature (CCT) of 5700K (±500K) . The luminaire should have 10 KV surg protection, PF ≥ 0.9 and total harmonic distortion of THD ≤ 10%, voltage range of 140-280V including all connections complete all as specified.

M&L for building security light bracket made out of 40mm dia light grade GI pipe of 1.2 m length bent to required shape suitable for fixing street light fitting on Steel tubular pole/wall including two Nos clamps made out 40mm X 6mm flat with suitable nuts and bolts including two coats of aluminium paint over a coating of red oxide primer complete all as directed taking down old unserviceable bracket as scrap any size / description.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one Single pole MCB 20 amp

M&L vertical load line distribution board factory made and tested made of sheet metal enclosure powder coated suitable for MCCB 100A triple pole and neutral as incomer and outgoing MCBs, 4 way TPN with rated busbar 415 volts,neutral link, Blanking plates (Without MCCB/MCBs) IP 43 (double door type) ISI marked suitable for G Frame MCCB 100 Amp as incommer. (Note MCCB Price should be measured and paid seperately)

S&F in repair of MCCB 4P 160 Amps, breaking cap 25 KA, 4 Pole, 415V complete including taking down old MCBs all as specified and directed.

S&F MCB distribution board, SPN 12 way, Double door, sheet steel, phosphatised, powder painted with Copper bus-bar 200Amp, neutral link, earth bar and din rail , cable ties for cable management, 240 V complete all as specified.

All as per Item No 175.00 but for 8 Way

All as per Item No 175.00 but for 4 Way

S&F powder coated CRCA steel sheet MCB distrbution board, IP-43 IK-09 protection, double door recess mounted, TPN 4 way complete.

S&F 415V 10KA 'C' curve miniature circuit breaker (MCB), TPN 40-100 Amps, complete with connection (Note 100 Amp 3 Nos, 63 Amps 2 Nos)

S&F MCB SPN 40-63 Amps,' C' series , bracking cap 10KA, 240V complete.

S&F 415V 10KA 'C' curve miniature circuit breaker (MCB), TPN 40Amps complete

S&F MCB SP 63 Amps,' C' series , bracking cap 10KA, 240V complete.

S&F MCB SPN 32 Amps,' C' series , bracking cap 10KA, 240V complete.

S&F MCB SP 6-32 Amps, ' C' series ,bracking cap 10KA, 240V complete.

Taking out carefully by XLPE cable / service connection of any type and size

M&L for Sub Main Wiring for DB to DB with two runs single core 10 Sqmm PVC insulated unsheathed (FRLSH) cable with stranded copper conductor drawn in suitable size of rigid non-metallic PVC conduit and its all accessories complete concealed in wall/roof with and including 10 Sqmm copper green colour earth wire all as specified and directed by Engineer-in-Charge. nOTE - 02 run 10 Sq mm single core cable, one run of 10 Sq mm earth wire & One run of PVC conduit will measured as one RM.

S&F ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor. (Note : Old Fan should be deposited in MES Store)

S&F exhaust fan, steel body AC single Phase 230V of size 300mm sweep with blades, and frame and louvers complete all as specified and as directed. (Note : Old Fan should be deposited in MES Store)

S&F exhaust fan, steel body AC single Phase 230V of size 380mm sweep with blades, and frame and louvers complete all as specified and as directed. (Note : Old Fan should be deposited in MES Store)

S&F Wall fans with three blade 400 mm size, 1350 RPM, Aerodynamic Blade Design for High Air Delivery, Anti - Rust Protection, 100% Copper Motor

S&F Wall fans with three blade 400 mm size complete

Cutting holes for air ducting of exhaust fan in Circle / square shape as per requirement and making good to facing where required & pointing in CM 1:3 to ends or edges complete all as specified and as directed.

Supply, laying, jointing and testing of XLPE insulated, sheathed, armoured, heavy duty LT 1100 volts grade cable with aluminium conductor cable size 70 sq mm 4 core laid in trenches / duct / fixing on walls / poles or passing through HDPE double wall corrugated pipe (outer dia should not be less then 40 mm) including connecting with suitable lugs, glands, nuts and bolts in existing Panel from pole / Main Panel Box and testing complete all as specified and directed. Note:- HDPE pipe rate shall be deemed in quoted rate above.

All as per Item No 193.00 but for cable size 25 sq mm 4 core

All as per Item No 193.00 but for cable size 16 sq mm 4 core

S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 meter in depth for laying of cable and getting out in soft / loose soil complete all as specified and directed by Engr-in-Charge

Returning, filling in including spreading, levelling, watering and well ramming excavated soil in layers not exceeding 25 cm thick each, back in trenches after cables have been laid and tested,poles, stays , struts have been erected and tested , all as specified.

Removing excavated surplus (soil) obtained from excavation to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete, all as specified.

M&l for Earthing complete with GI earth plate 600mm x 600mm x 6.3 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and charcoal filling incl necessary excavation and earth work complete all as specified and as directed.

All as per Item No 200.00 but for using galvanised iron strip 25×4mm as earthing lead

Supply installing commissioning & testing LT feeder piller panel board factory made, out door, cubical type, vermin proof, dust proof, water proof made out of 3.15 mm thick CRCA sheetand angle iron frame of size 50x50x6 mm inside depth not less than 50 cm and size suitable to accomodate the following accessories with insulated TPN Aluminium busbar of rating not less than 1.5 times the rated capacity of the incomer MCCB. both side openable (front & back) with locking arrangement duly painted with coat of synthetic enamel paint over a coat of red oxide primer both internally and externally and connecting with cable with lugs including internal wiring with copper cable of suitable size using lugs compressing the following accessories all as directed. (Notes : The rate quoted shall include for earth work & excavation for angle iron frame for foundation of panel board upto 0.50 m below GL in any type of soil & PCC (1:4:8), D2 filling in foundation the ground clearance of panel board shall be 0.40 m GL to the bottom of panel board ) and Aluminium bus bar 500 Amps-04 Nos duly colour sleeved mounted on epoxy insulators-01 set.Note:Panel board shall be approved by CPRI and certificate to be produced and to be submitted in the office. incoming :- (a) MCCB 4 P, 415 Volt 250 Amps, 35KA, 50 Hz with fixed thermal and magnetic setting -01 No Outgoing :- (a) MCCB 4 P, 415 Volt 160 Amps, 36 KA, 50 Hz with fixed thermal and magnetic setting -03 No (b) MCCB 4 P, 415 Volt 100 Amps, 36 KA, 50 Hz with fixed thermal and magnetic setting -01 Nos. (c) MCB 2 P, 220 Volt 32 Amps, 25 KA, 50 Hz with fixed thermal and magnetic setting -03 Nos (d) Multifunction Digital square type intelligent panel meter to measure voltage, current, frequency, & Power factor - 01 No

M/s Orient Traders (BID ID -3509217)

B S ENTERPRISES (BID ID -3509072)

VASUNDHARA AND COMPANY (BID ID -3515075)

M/s Hoti Lal Contractor (BID ID -3509649)

M/S ANIL KUMAR (BID ID -3504733)