SPL REPAIR TO BLDG NO NP-4 AT RANI KA BAGH AND CERTAIN OTHER SANCTIONED WORKS UNDER GE SATWARI

Taking down chowkats or frames with shutter (without taking off shutter from the frame) n. exc 1.5 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 sqm & n. exc 4 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubing down with water etc and removing unserviceable material outside defence land complete all as specified and directed.

Dismantling floor, hearth or wall tiling/ terrazzo dado from wall surface including cement mortar bedding, (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specied and directed.

Demolition of plain cement concrete of any description and in any position not otherwise specifically provided and including removing from site to a distance n exc 500 mtrs , complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry , built in cement mortar or cement lime mortar including all quoins, arches & pillars etc of any description and in any position and removing unserviceable material from work site to outside defence premises complete all as specified and directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided and including removing from site to a distance n exc 500 mtrs , complete all as specified and as directed.

M&L for 25 mm thick plain cement concrete 1:2:4, type B-0, (using 12.5 mm graded crushed stone aggregate) as in sub base/ levelling course of floors, finished even and fair complete all as specified and directed.

M&L for 7 to 8mm thick non skid coloured ceramic tiles (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and poined in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed in cement motar 1:6 complete all as specified and directed.

M&L for 8 to 9 mm thick vitrified ceramic (double charged), edge cut, joint free, coloured or printed, any shade tiles (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles using spacers & gap filled with silicon sealant over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for 8 to 9 mm thick vitrified ceramic double charged, edge cut, joint free, coloured or printed any shade tiles (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm , as in vertical surfaces such as skirting / dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles using spacers & gap filled with silicon sealant over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured tiles,300x600x7 mm thick, as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colored cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for 18 to 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing at edges complete all as specified and directed.

M&L for anti termite treatment by treating the top surface of filled earth and plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed .

M&L for 75mm thick PCC 1:3:6 , type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection, laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. surfaces finished even and fair including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed .

M&L for reinforced cement concrete 1:2:4,type B-1 (using 20mm graded crushed stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4,type B-1 (using 20mm graded crushed stone aggregates) as in beams,lintel chajjas,door pillars and like complete all as specified and directed.

M&L for use and waste of form work to softfits of suspended slabs such as roof slabs , floor slabs , landings and similar work, not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete complete all as specified and directed.

M&L for use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed

M&L for use and waste of formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete railings, openings in concrete walls, floor and roofs, n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n. exc 20cm wide for rough finished surface complete all as specified and directed .

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups , spacers and binders including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed .

M&L for brick work with sub class 'B' bricks, using old size bricks, straight or curved on plan exceeding 6m mean radius , built in cement mortar 1:6 complete all as specified and directed

M&L for brick work with old size sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed .

M&L for rendering 15mm thick in cement mortar 1:6 on brick work or concrete surfaces, surface finished even and smooth without using extra cement complete all s specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on brick work or concrete surface, surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and directed.

Complete removal of existing water proofing treatment of any description including under layer, taking down cement plaster any thickness,concrete,mud phuska etc and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust and removal of debris off the premises including grubbing up of trees complete all as specified and directed.

M&L for cleaning of the exposed concrete slab & like and repairing the surface irregularities like cracks, potholes with HS Latex Plus(or equivalent) & cement in mixing ratio of 1:4 as per manufacturers method statement by Berger HS Rapairo (or equivalent) i complete all as specified and directed .

M&L for PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in padding over roof finished & laid to required slope, mud stops,roof kerbs complete all as specified and directed .

M&L for HomeSheild PU Roofkoat(or equivalent) is a one component liquid ,solvent free , cold applied , water-proofing membrane that is highly elastic and UV resistant with 10 years warranty .ASTM D 6083-97 a Waterproofing and heat reflecting system having following key performance properties:- a) UV resistant ,prevent yellowing and weathering b) Highly elastic upto 350% and crack bridging c) Excellent adhesion on porous and non-porous substrates d) Tensile Strength >10 N/mm2 with GeoTextile fleece e) Soler Reflective Index (SRI) more then 109-111 ASTM E1980-11 System: First coat:Providing and applying primer over the prepared surface with HS PU roofkoat Primer(or equivalent) Coverage: 0.2kg/sqm(with 50% dilution of water) Reinforcement: Geotextile 40 gsm Second coat:Home sheildroofkoat(or equivalent) Consumption: 0.5 kg/sqm. Third coat: HS PU roofkoat(or equivalent) Consumption : 0.8 kg/sqm. System buildup-1.5kg/sqm with geotextile of 40gsm

S&F aluminium alloy powder coated aluminium door frame fixed with side hung shutters and glazing or composite panel LDPE core PET coating ( both side decorative type ) fixed with and including 5.50mm thick black film glass fixed with rubber gasket with aluminium heading, clips, frame made with aluminium box section as appended below complete all as specified and directed :- (a) Frame 100x44x1.48mm thick with rawl plug (b) Middle and lock rail : 150x44x1.48mm thick (c) Bottom rail : 150x44x1.48mm thick (d) Top rail/style : 85x44x1.48mm thick (e) Aluminium beading : 0.7mm thick (g) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long, brass mortise lock 100mm 4 leaver, aluminium stopper 100 mm long, Including Heavy duty hydraulic door stopper. (h) 04X stainless steel Hinges 100mm long (02x top,01x centre and 01x bottom) on each shutter (j) Making good the wall surface to match with existing finishes complete.

S&F aluminium alloy powder coated aluminium door frame fixed with inside glazing and outside stainless steel wire mesh ,side hung shutters fixed with rubber gasket and aluminium beading, clips, frame made with aluminium box section as appended below complete all as specified and directed :- (a) Frame 100x44x1.48mm thick with rawl plug (b) Middle and lock rail : 150x44x1.48mm thick (c) Bottom rail : 150x44x1.48mm thick (d) Top rail/style : 85x44x1.48mm thick (e) Aluminium beading : 0.7mm thick (f) Plain glass 5.5mm thick with black film (g) Stainless steel wire cloth, 0.36 mm nominal dia of wire and average with of aperture 1.40 mm and fixed with stainless steel wire staples (h) 04X stainless steel Hinges 100mm long (02x top,01x centre and 01x bottom) on each shutter (j) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long, brass mortise lock 100mm 4 leaver ,aluminium stopper 100mm long, Including Heavy duty Hydroulic door stopper. (k) Making good the wall surface to match with existing finishes complete.

S&F Powder coated aluminium sliding windows frame with movable shutter ( sliding on minimum two PVC roller of best quality, for each shutter on three tracks with 01x stainless steel mosquito proofing shutter and 02x glazing shutter and including 5.50 mm thick glass & stainless steel wire mesh fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below- (i) Window frame :95x35mm X 1.48 mm thick for three tracks. (ii) Top/bottom rail and style / rail of shutter : 19x38x1.48mm thick and over. (iii) Aluminium beading - 0.7mm thick (iv) stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperature 1.40mm and fixed in aluminium window or alongwith F/Y section fixed with aluminium wire staples complete. (v) Aluminium fittings such aluminium handle with auto interlocking closing (vi) Making good the wall surfaces to match with existing surfaces complete

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 75 x 50 mm comprising of virgin PVC polymer of K value 58-60 (suspension Grade), calcium carbonate and natural fibers and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum and screw withdrawal strength of 2200 N (Face) and 1100N (edge), minimum compressive strength 58 N/ mm ² ,modules of elasticity 900 N/mm ² and resistance of spread of flame of Class A category with property of being termite/borer proof,water/moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note:- Variation in profile size of frame ±5mm is allowed and contractor's quoted rate is deemed to include the same

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush shutter of 30mm size comprising of virgin polymer of K value 58-60 (suspension Grade),calcium carbonate and natural fibres (wood powder/rich husk/wheat husk) and non toxic additives (maximum toxicity index of 12 to 100gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) and 900N (edge), minimum compressive strength 50 N/ mm ² ,modules of elasticity 850 N/mm ² and resistance of spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges (02 Nos in each shutter) of required size with necessary full body threaded star headed counter sunk S.S scrwes complete all as specified and directed. . Note:- Variation in profile size of shutter ±5mm is allowed and contractor's quoted rate is deemed to include the same

S&F aluminium ventilator of section size 65x38mm, fixed type, including figured glass at bottom and stainless steel wire mesh cloth at top complete all as specified and directed .

S&F aluminium anodised barrel tower bolts, 150mm long of extruded section, fixed to doors with screws complete all as specified and directed.

S&F aluminium anodised ,cast type handle 125mm size complete all as spcified and directed.

S&F in replacement Rotational moulded polyethlene water storage tanks of 1000 litres capacity (cylindrical vertical with closed top) with plastic lid cover, hoisted and fixed in position including making connections complete all as specified and directed.

S&F in repair Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule of bore 20mm complete all as specified and directed.

Taking up or down 15mm dia GI tubing and conncetions including cleaning for refixing or removal to store complete all as specified and directed

Taking up or down 20 mm dia GI tubing and conncetions including cleaning for refixing or removal to store complete all as specified and directed

S&F Galvanised steel tubing, 15mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed

S&F Galvanised steel tubing, 20mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed

S&F vitreous china counter top wash basin, size 560x400x250mm, oval shape , white, to be fixed on counter/ RCC slab including bottle trap, 32mm waste pipe complete all as specified & directed

S&F in repair CP brass wall mixer 3-in-1 system with provision of overhead & hand shower complete with 150mm long flexible tube and crutch (quarter turn) pipe, for hot and cold water, screwed down for iron of bore15mm complete all as specified and directed.

S&F CP brass wash basin mixer, long body, swan neck type for mixing hot & cold water ,screwed down for iron pipe of bore 15mm including necessary fittings complete all as specified and directed .

S&F in repair brass chromium plated shower rose of square size 150 mm with 450mm long arm and with or without swivel joints to steel pipe or union complete all as specified and as directed.

S&F in repair bib tap with flange, quarter turn, long body, chromium plated, fancy type, cast copper alloy ,screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair two way bib cock with flange,cast copper alloy , fancy type, chromium plated, screwed down for high pressure with crutch or butterfly handle, screwed both ends for iron pipe of 15mm bore complete all as specified and directed.

S&F in repair stainless steel tubular towel ring ,rectangular of size 20cmx12.5cm, fixed with CP brass screws and brackets including plastic beads complete all as specified and directed.

S&F in repair PVC connection 15 mm x 450 mm including PVC check nut at both ends complete all as specified and direced.

S&F in repair chromium plated soap dish of size 160x160x90mm, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repair angle valve with flange,cast copper alloy,fancy type,chromium plated, screwed down for high pressure , screwed both ends for iron pipe of 15mm bore complete all as specified and dircted.

S&F in repair sheet glass shelf assembly consisiting of 5.5 mm thick sheet glass, shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed .

S&F in repair EWC vitreous china, twin action, one piece wash down water closet pan, rimlesss,coloured of size 675mmx360mmx750mm with Soft Close Duroplast Seat Cover,S trap 300mm & accessories complete all as specified and directed.

S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 8mm dia pipe with 1.00 metre long flexible tube and ABS wall hook including making connectios and fixed in position complete all as specified and directed.

S&F in repair PVC (SWR) type-B multi floor trap plain with stainless steel grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed.

S&F in repair PVC (SWR) floor trap plain with stainless steel grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed.

S&F UPVC (SWR) type B pipes, 110 mm bore, single socketed, in any length with rubber ring joints,laid in floors/treaches or fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed.

S&F UPVC (SWR) type B pipes, 75 mm bore, single socketed, in any length with rubber ring joints, laid in floors/treaches or fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed.

S&F UPVC (SWR) bends with access door, any radius, 75 mm bore complete all as specified and directed

S&F UPVC (SWR) bends with access door, any radius, 110 mm bore complete all as specified and directed

S&F UPVC (SWR), junction single, (single 'T') equal or unequal for 75 mm bore complete all as specified and directed

S&F UPVC (SWR), junction single, (single 'T') equal or unequal for 110 mm bore complete all as specified and directed

S&F in repair chromium plated stainless steel towel hanger with 06 hooks fixed to wall complete all as specified and directed.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries rails and fastening and heavy bracket framing (beam, tee, angle channel or flat sections) including distance pieces, cleats etc confirmimg to Fe 290 (Gde E -165) complete all as specified and directed .

S&F Pre painted galvalume aluminium zinc coating (AZ-150 micron) GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified and directed .

S&F Pre painted galvalume aluminium zinc coating (AZ-150 micron) GI based plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified and directed.

S&F structural steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade St -240 complete all as specified and directed .

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting exc 10cm but not exc 40 cm girth in brick walls and RCC chajjas complete all as specified and directed .

Dismantling wall and ceiling boards (fibre,pulp, insulation) or insulation boards/ slabs/blankets, any thickness, including cover fillets etc complete all as specified & directed.

Providing and fixing false ceiling at all heights with GRG (Glass fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture with fully perforated 12 mm thick micro tegular edges, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRCO.50 to 0.75 as per BS 476 (Part -4)-1970 and light reflectance of 85% (Minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33 mm thick (Galvanized @120 grams per Sqm incl both sides) comprising of Main T runners of Size 15x32 mm of length 3000mm, cross T of Size 15x32 mm of length 600 mm to form grid module of size 600x600 mm, suspended from ceiling using galvanized mild steel items (Galvanizing @ 80 grams per Sqm) i.e., 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod up to 1000 mtr length and L-shape level adjuster of size 85x25x2 mm Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall/partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long dry wood screws. The work shall be carried out as per specifications, drawing and as per directions of Engr-in-Charge.

M&L for applying rustic texture paint with the following process as per manufacturer's instructions complete all as specified and directed:- (a) The surface should be completely dry and free from loose particles , applying one coat of water proof wall care putty 1 to 2mm thick and one coat of rustic texture finish 1.5mm to 2mm thick uniformly and draw pattern/design & preparing the surface with emry paper 180 No. (b) Wiping cleaning and applying two coats of primer and allow to dry for 6 to 8 hrs (c) Applying two coats of interior emulsion paint Note:- Design/pattern to be approved by Engineer-in-charge.

M&L for preparation of new or previously untreated steel surface of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M&L for complete removal of existing treatment of wall/ceiling , roof projection, including facia, cornices, etc by scrapping with mechanical wall sander (having mechanical vaccum mechanical) having RPM not less than 1500, sanding pad of 60 grit having dia of 7"/9" to make the surface free from dust, loose paint etc by skilled labour (up to 4th storey with necessary scaffolding) complete all as specified and directed

M&L for water proof cement based putty @ 1kg (undiluted) per sqm of average thickness 1 mm over the plastered painted exterior wall surfaces of walls (upto 4th storey with necessary scaffolding ) including prepartion of surfaces by scarpping to prepare the surface and sanding of the putty surfaces with mechanical wall sander (having mechanical vaccum mechanism ) having RPM not less than 1500 ,sanding pads of 240 Grit or above to make the surface free from dust etc by skilled llabour as per following steps:- Steps 1:- Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of minimum 2.5 kg putty per minute. Step 2:- Apply the first coat of prepared mixer with the manually required help of fully automatic airless spary machine of putty application, finishing the surface even and smooth in level without any undulation. Step 3:- Allow 6 to 8 hour time to dry the putty surface, Apply the further more coat of preparaed mixer with the help of fully automatic airless spary machine of putty application, finishing the surface even and smooth in level without any undulation. Note:- Work shall be carried out by the authorised applicator of manufacturer and shall be approved by the GE before commecement of work at site.

M&L for one coat of acrylic water based exterior/interior grade primer @ 0.9 ltrs (undiluted) per 10 sqm, diluted with water in 1.1 ratio to be applied with fully automatic airless spary machine of paint application with a flow speed of min 1 litres per mintues having a pressure of 3300 PSI and Allow 6 to 8 hours to dry surface for painting of subbsequent coats (walls up to 4th storey with necessary scaffolding) complete all as specified and directed . Note:- Work shall be carried out by the authorised applicator of manufacturer and shall be approved by the GE before commecement of work at site.

M&L for Preparing the primer surface and applying two coats of oil bound distemper on wall/ceilling (up to 4th storey with necessary scaffolding) using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed . Note:- Work shall be carried out by the authorised applicator of manufacturer and shall be approved by the GE before commecement of work at site.

M&L for water based premium acrylic smooth exterior emulsion for approved colour (up to 4th storey with necessary scaffolding) with silicon additive excellent dirt pickup resistance with low VOC less than 50 AntifugalAnti Algai properties in two coat @1.79 litre (unndiluted) /10 sq mtrs diluted with water as per manufacturer instructions applied over priming surface with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in between subsequent coats of paint complete all as specified and directe Note:- Work shall be carried out by the authorised applicator of manufacturer and shall be approved by the GE before commecement of work at site.

S&F 100mm long stainless steel butt hinges, fixed with screws complete all as specified and directed

S&F in repair continuous (piano) hinges,width of flaps (when open) 30 mm, heavy duty, mild steel, bright finish or electrogalvanised sutable for 19mm thick shutter and fixed, complete all as specified and directed.

S&F hasp & staple 75 mm in length, safety type, aluminum anodised with steel hinge pin including bolt to hinge plate fixed with screws complete all as specified and directed.

S&F 100mm long stainless steel glossy finish handle, fixed with stainless steel screws complete all as specified and directed

Surface dressing n.exc. 15 cm deep and getting out in any type of soil complete all as specified and directed.

Excavating in trenches, n. exc 1.5 m wide and n. exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n. exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil complete all as specified and directed.

Removing excavated material to a distance n.exc 50 m & depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed .

M&L for plain cement concrete 1:4:8, type D2 (using 40mm graded crushed stone aggregates) as in foundation, filling & mass concrete complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4,type B-1 (using 20 mm graded crushed stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed .

M&L for reinforced cement concrete 1:2:4,type B-1 (using 20 mm graded crushed stone aggregates) as in column,pillars, piers and struts complete all as specified and directed.

M&L for use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc complete all as specified and directed.

M&L for use and waste of formwork to sides of pillars, posts, struts, piers, columns, and stanchions etc complete all as specified and directed .

M&L Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base, finishing surfaces even and fair complete all as specified and directed.

M&L for brick work with fly ash bricks using old size bricks, straight or curved on plan exceeding exc 6 metre mean radius, built in cement mortar 1:6 complete all as specified and directed .

M&L for providing and laying 60 mm thick factory made charmfered edge cement concrete paver block of M-35 grade of approved colour, design & pattern as in foothpath, parks, lawns, drive ways or light traffic parking etc of required strength , thickness & size/ shape made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

S&F 12.5 mm thick sheet toughened glass (tinted/frosted/plain) as in partition wall with any type of eaching designed on glass with necessary fixing arrangements complete all as specified and sirected.

S&F aluminium alloy powder coated aluminium door frame fixed with side hung shutters and glazing or composite panel LDPE core PET coating ( both side decorative type ) fixed with and including 5.0mm thick aluminium composite panel fixed with rubber gasket with aluminium heading, clips, frame made with aluminium box section as appended below complete all as specified and directed :- (a) Frame 100x38x1.48mm thick with rawl plug (b) Middle and lock rail : 85x44x1.48mm thick (c) Bottom rail : 114x44x1.48mm thick (d) Top rail/style : 114x44x1.48mm thick (e) Aluminium beading : 0.7mm thick (f) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long, brass mortise lock 100mm 4 leaver with stainless steel hinges (g) Making good the wall surface to match with existing finishes complete.

S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to distributed surface of walls complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick ( style ) consisting of frame work made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour P.V.C‘ C’ channel having a PVC sheet strip 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap inserts for top rail; and bottom rail paneling of plain, colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rail with suitable PVC sheets beading and jointed together with solvent cement S&F in frame at site as per specification complete all as specified and directed.

S&F pressed steel ventilators, fixed type, with glazing bars complete all as specified and directed.

M&L for 3 mm thick, plain sheet glass, ordinary quality and glazing with oil putty or with any type of beads, in squares n. exc 0.5 sqm each pane complete all as specified and directed.

S&F stainless steel wire cloth , 0.36 mm normal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F Mild steel sliding door bolts 150mm long,plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tanks of 1000 litres capacity (cylindrical vertical with closed top) with plastic lid cover, hoisted and fixed in position including making connections complete all as specified and directed.

S&F Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule of bore 20mm complete all as specified and directed.

S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed .

S&F 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge with stainless steel brackets near to ends with stainless steel finials at both ends and necessary fittings complete all as specified and directed.

S&F bib tap with flange, quarter turn, long body, chromium plated, fancy type, cast copper alloy ,screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F two way bib cock with flange,cast copper alloy , fancy type, chromium plated, screwed down for high pressure with crutch or butterfly handle, screwed both ends for iron pipe of 15mm bore complete all as specified and directed.

S&F PVC connection 15 mm x 450 mm including PVC check nut at both ends complete all as specified and direced.

S&F chromium plated soap dish of size 160x160x90mm, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F stainless steel tubular towel ring ,rectangular of size 20cmx12.5cm, fixed with CP brass screws and brackets including plastic beads complete all as specified and directed.

S&F sheet glass shelf assembly consisiting of 5.5 mm thick sheet glass, shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F angle valve with flange,cast copper alloy,fancy type,chromium plated, screwed down for high pressure , screwed both ends for iron pipe of 15mm bore complete all as specified and dircted.

S&F vitreous china squatting pan, Orissa pattern, size 580 x 440mm white with integral foot rest, cast iron 'P' or 'S' trap of size 100mm, including provision of plain cement concrete bedding and connection to trap and to flushing pipe, anti syphonage pipe etc and making good the floors complete all a specified and directed

S&F vitreous china wash down water closet pan (pedestal pattern) white in colour including connection pipe to union of flushing cistern, inlet and overflow pipes, connecting only to flushing cistern, anti-syphonage pipe with PVC flush pipe of 32mm dia including plastic seat with cover, white in colour with mild steel chromium plated hinges and 'P' or 'S' trap device complete all as specified and directed

S&F 10 litres PVC, valveless, syphonic action type, flushing cistern, low level,white, with inlet, ball valve, float 32mm PVC 'L' bend and handle including brackets complete all as specified and directed

S&F health faucet (ABS Body) mild steel chromium plated suitable for 8mm dia pipe with 1.0 metre long flexible tube and ABS wall hook including making connectios and fixed in position complete all as specified and directed.

S&F chromium plated toilet paper holder fixed to walls with chromium plated brass screws complete all as specified and directed.

S&F Vitreous china urinal of size 375x390x590mm, white including providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, flush pipe, grating and union for discharge pipe and Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm bore complete all as specified and directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed .

S&F PVC (SWR) type-B multi floor trap plain with stainless steel grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed.

S&F PVC (SWR) floor trap plain with stainless steel grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed.

S&F PVC (SWR) bends any radius, 75 mm bore complete all as specified and directed

S&F PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed

S&F UPVC (SWR) type-B vent cowl 75 mm dia complete all as specified and directed

S&F UPVC (SWR) type-B vent cowl 110 mm dia complete all as specified and directed

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over 1mm thick wall care putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over1mm thick cement base wall care putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for Framed work as in doors or gates,water tank staging,cooler stand,cattle fencing etc of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing using Fe 290 (Gde-E-165) complete. complete all as specified and directed .

S&F Reinforced concrete pipes of size 150mm (internal dia),class NP-2 , laid, jointed and tested complete with collar complete all as specified and directed .

M&L for Concrete bed to drain pipes of dia 150mm in cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) including packing under and haunching against the sides of pipe after laid & tested including necessary formwork complete all as specified and directed.

M&L for plain cement concrete 1:2:4 ,type B1(using 12.5mm graded crushed stone aggregates)as in lintels upto 1.5m clear span, window or door cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm in height, copings,side posts of precast jallies,benching etc. including slightly rounded or chamfered angles including necessary formwork complete all as specified and directed.

M&L for providing precast cement concrete 1:2:4, type B1, (using 20mm graded crushed stone aggregates) as in landings, cover slabs (for man holes cover) and similar articles with plain faces set in cement mortar 1:4 complete all as specified and directed .

M&L for providing precast reinforced cement concrete M-30 (Design mix) (using 20mm graded crushed stone aggregates) as in drain cover slabs (width of drain n.exc 3.0 m) complete all as specified and directed .

M&L for plain cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in surface channel and drain including necessary form work complete all as specified and directed

Taking down carefully existing aluminium/copper point wiring for light, fan, socket or power bell complete with fittings such as Switches, sockets, ceiling roses, holders, call bells etc & making good the disturbed surfaces of walls/ceiling, matching the colour with existing surface complete all as specified and directed. Note : Rate for making good shall be deemed to be included in above item rate.

Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable(ISI marked) 1100 volts grade FRLSH with multistranded copper conductor, drawn through concealed / surface in wall / roof/ceiling surface and its accessories on the surface etc including PVC rigid concealed medium grade conduit of suitable size with all accessories such as bend, reducers, MS hooks including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc including continuous earth wire of size 1.5 Sqmm PVC FRLSH stranded copper conductor unsheathed, insulated, stranded connected to common earth point dolly for one light point/fan point/call bell point, 230 volts controlled by one switch complete all as specified and directed . Note:- Proper colour coding is to be followed as per IS specifications.

All as per srl item No 154 above but One 3 pin socket outlet 6 amp independent complete all as specifieds and directed

All as per srl item No 154 above but One 3 pin socket outlet 6 amp same board complete all as specifieds and directed

All as per srl item No 154 above but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire.

S&F modular type switch, one way 6 Amps , 1 module complete all as specifieds and directed .

S&F modular type socket 3 pin, 6 Amps, 2 module complete all as specifieds and directed

S&F modular type switch, one way, 16 Amps, 1 module complete all as specifieds and directed .

S&F modular type socket 3 pin, 6 A/16 Amps, 2 module complete all as specifieds and directed .

S&F ceiling rose, surface backelite, two/ three terminal, 240 volts complete all as specifieds and directed .

S&F modular fan regulator,120 Watt, 2 module complete all as specifieds and directed

S&F LED light fitting 1 x 20Watt, 220V,decorative box type with driver, holder including LED tube light, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose with all fixing arrengenment complete all as specifieds and directed .

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt, 220 V, AC ,decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specifieds and directed .

S&F exhaust fan, steel body, AC single phase. 230 V of size 300 mm sweep with, blades and frame and louvers, hanging on wall with 4 Nos steel fasterners 10mm dia & 100mm long including wall hole and making good the disturbed surfaces as per existing complete all as specified & directed

S&F MCB SPN,40-63 Amp, 240 Volts with rupturing capacity 10 KA, 'C' series, complete all as specifieds and directed .

S&F MCB Single pole, 6 to 32 Amp, 240 Volts with rupturing capacity 10 KA, 'C' series, complete all as specifieds and directed .

S&F Sheet metal enclosure for DBs,SPN, double door,IP-43 protected, 240 Volts,8 ways with 200 amps rated copper bus bar complete all as specified and directed

S&F Submain wiring with two runs of single core PVC FRLSH unsheathed, insulated, copper cable of 4 Sqmm size, multi stranded, 1100 volts grade with PVC insulated,unsheathed FRLSH copper wire 4 Sqmm for continous earth wire drawn into and including concealed PVC conduit of suitable size complete all as specified and directed . Note :- Two runs of 4 Sqmm copper cable and one run of 4 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length)

S&F Submain wiring with two runs of single core PVC FRLSH unsheathed, insulated, copper cable of 6 Sqmm size, multi stranded, 1100 volts grade with PVC insulated,unsheathed FRLSH copper wire 6 Sqmm for continous earth wire drawn into and including concealed PVC conduit of suitable size complete all as specified and directed . Note :- Two runs of 6 Sqmm copper cable and one run of 6 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length)

S&F energy saving new generation 10W LED bulk head luminaire with opal diffuser, IP 65 and including connecting up with twin core twisted flexible copper coductor cable with suitable size of 230 volt,50 Hz complete all as specified and directed.

M&L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1, precast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh ,15mm dia light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specifieds and directed ..

M&L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the earth plate not less than 1.5 mtr below ground level connected to GI strip 32x6mm by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1, precast RCC cover slab using reinfocement with XPM weighing not less than 4.00 kg/Sqm with suitable handle made of 12mm round bar including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh ,40mm dia medium grade galvanised steel tubing upto 7.5 m length for drawing earth strip protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 16 Sqmm, 4.0 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and directed.

S&F multi core round PVC-FRLSH insulated aluminium conductor (flexible) industrial cables PVC sheathed , 1100 volts of size 2.5 Sqmm, 4 core from panel to street light inside/outside pole complete all as specified..

M&L for sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment.

M&L for factory made unreinforced precast concrete cable cover LV type-1, flat, of size 250x150x40mm, laid flat and dry in trenches over the cable for protection, length perpendicular to the direction of cable adjacent to each other, complete all as specified and directed.

Supply and installation galvanised steel high mast lighting system of 16mtr in two segments, 3mm section thickness with 2/3 including 3 phase motor of suitable capacity with wire rope system, including 08 Nos 200W LED flood lights with all connecting accessories for smooth functioning & lighting, including motor & light controlling panel, RCC foundation with suitable drawing & all connecting Nut bolts required for its foundation complete all as specified and directed. (a) General specification (i) Height of mast -16 mtrs, (ii) Material of construction : BS EN 10025/IS 2062, (iii) Thickness of material - Top section 3mm, bottom section 4 mm, (iv) Cross section of mast (number of sides)-20 sided polygon, (v) Length of individual section - Top section : 8.35 mtrs, Bottom section : 8.35 mtrs, (vi) Diameter - Base dia : 460mm, top dia : 150mm, (vii) Types of joints - stress slip fit joints, (viii) Length of overlap-1.5 times the dia of intersection, (ix) Metal protection treatment - Hot dip galvanised as per IS 4759/IS 2629,(x) Thickness of galvanistaion - average 70 micros, (xi) Size of door opening at base of mast - 1200mm x 300mm, (xii) Types of locking on door panel - Close fitting door with allen key locking with suitable reinforcement to avoid buckling at base of mast. (xiii) Lightening protection finial - GI single spike of length 1200mm, (xiv) Size of base plate - Dia : 670mm, thickness : 30mm, (b) Dynamic loading as prevailing at site (i) Max wind speed : 180 Km/hr (ii) Number of foundation bolts -08 Nos (iii) PCD of foundation bolts - 590mm (iv) Dia of foundation bolts - M30, (v) Lenght of foundation bolts - 850mm (c) Lantern carriage (i) Material of construction - 40 NB/ ERW CKASS B-MS PIPE, (ii) Dia of lantern carriage ring -800mm (ID) (iii) Construction - 9 arms welded (iv) Number of joints - 2 segments (v) Load carrying capacity - 16 lumainaries, symmerical (d) Winch : (i) Number of drums per winch - double drum (ii) Gear Ratio - 50:1 (iii) Capacity SWL750Kgs (iv) Method of operation - Motor or manual (v) Lubrication arrangements - Self Lubricating in permanent oil bath (vi) Type of lubricant - SAE 90/140