GE(S)/M-48/2021-22

Amount

Demolition of cement concrete (unreinforced) of any description and in any position not specifically provided for, complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not specifically provided for, complete all as specified and directed. Note :-Reinforcement cut as required to facilitate demolition.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 Sqm each and removing from site, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but not exc 4.00 Sqm each and removing from site, complete all as specified and directed.

Removing old lime wash (if any), hacking for key, raking out joints of old brick work or stone work built in lime or mud mortar; not previously plastered; and scrubbing down with water etc. to receive plaster complete all as specified and directed.

Excavating in trenches in any type of soil, n. exc. 1.5 m wide and n. exc. 1.5 m in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc n. exc. 10 sqm on plan and n.exc 1.5 m in depth and getting out complete all as specified and directed.

Removing excavated material (soil) n.exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

M&L for loose filling of broken bricks of gauge exc. 63mm and n. exc. 100mm complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40 mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in benching, haunching, coping etc, including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for plain cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in kerbs mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L for precast cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in factory made kerb stones shape and size as required and set in CM 1:6, complete all as specified and directed.

M&L for plain cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in walls, retaining walls, basement walls, ballast walls and the like; above top of footings; including attached pilaster and buttresses complete all as specified and directed.

M&L for precast cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set in CM 1:6, complete all as specified and directed.

M&L PCC 1:2:4, type B-2 (using 40mm graded crushed stone aggregates) as surface channels and drains complete all as specified and directed.

M&L for RCC M-25 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for RCC M-25 (using 20 mm graded stone aggregate) as in chajjas complete all as specified and directed.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6 Mtr mean radius, built in CM 1:6, including demolition of existing brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, including removal of deberies out of MoD land complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6 Mtr mean radius, built in CM 1:4, including demolition of existing brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, including removal of deberies out of MoD land complete all as specified and directed.

M&L for brick masonry (EXCEPT BRICKS) straight or curved on plan exc 6 Mtr mean radius, built in CM 1:4, complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6 Mtr mean radius, built in CM 1:6, complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick wall, built in CM 1:4, complete all as specified and directed.

M&L for brick work with fly ash bricks, in one brick thick honey comb. walling, built in CM 1:4, complete all as specified and directed.

Cutting chases, pinning in brick work making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.: and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified and directed.

M&L for form work to soffits of flat, fair finished surfaces of concrete of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick(Horizontal or sloping) complete all as specified and directed.

M&L for form work to chulla hoods, chajjas, troughs and similar items including edges finished the surface fair finished complete all as specified and directed.

M&L for form work to faces of in walls, retaining walls, basement walls, ballast walls and the like; above top of footings; including attached pilaster and buttresses, fair finished surfaces complete all as specified and directed.

M&L for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10 cm but n. exc. 20 cm wide, rough finished surfaces of concrete complete all as specified and directed.

M&L for 2nd class hard wood as in plain fillets framed work, square, rectangular or triangular in section, clean sawn, secured with nails or brads exc. 13Sqcm but n. exc. 25Sqcm complete all as specified and directed.

S&F 35mm thick 2nd class hardwood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

S&F 35mm thick factory made wire guazed and skeleton shutters (1st class softwood), open rebated and prepared to receive wire cloth, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing wire cloth etc. sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) and fitted to chowkats at site, complete all as specified and directed.

S&F Factory made solid panel PVC door shutter (Wood garin colour sheets on both sides) 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded wood grain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of wood grain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site, complete all as per specifications & drawing.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site, complete all as per specifications & drawing.

S&F Solid PVC door frame of size 50mm x 47mm, made out of 5mm thick plain colour PVC sheet reinforced with MS Square tube, suppling & fixing in opening at site, complete all as per specifications & drawing.

S&F factory made 18mm (+ 0.7mm) thick PVC cupboard shutter, printed one side with coating of ultra voilet chemical, glossy/mat finish incl. 100% termite/water proof, fire retardant, Eco friendly, density not less than 600Kg/cbm finish at all edges for making edges lipping/bending, complete as per direction of Engineer-in-Charge and manufacturer's specifications.

S&F 100mm size hasp and staple, aluminium anodised including bolts to hinge plate and fixed with screws.

S&F 100mm long butt hinges, type C-21, extruded aluminium alloy with galvanised mild steel hinge pin, anodised complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F 100mm long extruded aluminium alloy handle, fabricated type, anodised complete all as specified and directed.

S&F 150mm long extruded aluminium alloy handle, fabricated type, anodised complete all as specified and directed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, (ISI marked), complete all as specified and directed.

S&F 300mm size mild steel, ordinary rat tail, rod pattern spring including roller and roller plate, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F "as in repair" 20mm bore mild steel drapery rod with 1.0mm thick PVC wood grain coating including brackets and knobs, fixed on windows and doors for hanging curtains, complete all as specified and directed.

S&F Box type steel windows and ventilators, comprised of tubular frame and shutters made out of 1.25mm thick MS sheet tube, factory made with double side hung wire gauged shutter & glass/glazed shutter (wire cloth and glass panes shall be measured and paid separately under respective items of BOQ) with steel handle and steel peg stay dovetailed or welded including 2 Nos. tower bolts of 150mm long for each leaf and 10mm square bar grills at spacing as shown on drawing, welded to FI frame work including other fittings such as hinges, handles, tarred hold fasts etc. fixed in PCC blocks including two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as shown on drawing No. CEPZ/TD-354/09 sheet 1/3 to 3/3.

S&F pressed steel frame made out of MS sheet 1.25mm thick of size 125mm x 60mm for doors/windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars 6mm dia to 8mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel round bars 10 mm dia and over, cut to length, bent to shape required as in manhole cover handles, steps, clamps etc, complete all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregate) as in roof padding complete all as specified and directed.

M&L for removing existing roof treatment (any type) and roughening surfaces of old concrete floor by picking, sweeping/brushing clean and washing down with water to remove dust etc, and applying neat cement slurry with 3Kg of cement per Sqm complete all as specified and directed.

M&L for APP modified roof treatment over existing non-accessible RCC roof slab/chajjas/canopy/parapet wall, to be executed through approved applicator of the membrane manufactured with following specifications, complete all as specified and directed :- (a) Cleaning the top surface of RCC roofing properly with water. (b) Rendering 20mm thick in CM 1:3 mixed with liquid water proofing compound on RCC roof slab whilst the surface is still green, finished the surface even and smooth without using extra cement. (c) Applying oil bound bitumen primer @ 0.30 Litre/Sqm, manufactured by the same agency as that of APP with a density 0.87-0.89 KG/Litre at 25 degree centigrade on prepared surface. (d) Laying of membrane not less than 3.0mm thick APP modified water proofing membrane weighing not less than 3.60 KG/Sqm reinforced with non woven polyster fiber weight not less than 160 Gms/Sqm using butane torch by torch application with 10cm overlap and 15cm end lap. (e) Top of membrane shall be provided with solar reflective bituminous aluminum paint @ 0.10 KG/Sqm as prescribed by manufacturer of membrane. (e) APP Membrane shall be stick inside parapet where available by chase cutting and sealed with PCC 1:2:4,type B-0.

M&L for 50mm PCC 1:2:4 type B-1 (using 20 mm graded aggregate) as in floors laid in panels n. exc. 2.5 Sqm with top finished the surface even and smooth without using extra cement including glass dividing strips as per site requirement complete all as specified and directed

M&L for 75 mm thick plain cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of floors, complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection and paving, laid in slope, finished even and fair including making joints at every 2.5 mtr and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight, complete all as specified and directed.

M&L for coloured machine pressed precast rubber moulded concrete interlocking (Grey/red/yellow) paver block of any shape and size with 6-8mm white cement layer mixed with pigment and coated with epoxy coating having high glossy finish confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, laid dry over and including 50mm thick sand filling under paver, properly levelled etc, including taking out existing interlocking paver block complete all as specified and directed.

M&L for coloured machine pressed precast rubber moulded concrete interlocking (Grey/red/yellow) paver block of any shape and size with 6-8mm white cement layer mixed with pigment and coated with epoxy coating having high glossy finish confirming to IS 15658-2006 of 80mm thickness, M-40 Grade, laid dry over and including 50mm thick sand filling under paver, properly levelled etc, including taking out existing interlocking paver block complete all as specified and directed.

M&L for Fly Ash glossy finished coloured chequered cement concrete tiles of size 30cm X 30cm X 25mm thick, set, jointed & pointed in neat cement slurry with grey cement and pigment to match as in floors over and including 15mm thick screed bed or bedding layers in CM 1:6, including dismantling existing floor, hearth or wall tiling of any description, complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick, area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floors etc, set and jointed (joint free) in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:6 for laying floor finishes, complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick, area of each tile exc 0.18 Sqm but not exc 0.36 Sqm as in floors etc, set and jointed (joint free) in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:6 for laying floor finishes, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 300mm x 450mm x 7mm thick on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including rendering 10mm thick in CM 1:4 and finished rough to receive tiles including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for rendering 5mm thick in CM 1:3 on concrete surfaces of ceiling / top and sides of chajjas/facia of roof projection including necessary formwork, finishing the surface even and smooth without using extra cement, including taking down existing cement plaster on brick walls or stone walls of any description etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for 10mm thick rendering on faces of brick work or concrete surfaces of walls in cement mortar 1:6, finished even and smooth without using extra cement including taking down existing cement plaster on brick walls or stone walls of any description etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for 15mm thick rendering in two layers (5mm thick in CM 1:4 over 10mm thick in CM 1:6) on brick work and concrete surfaces of wall, finished the surface even and smooth without using extra cement, mixing and including WPC @ 200ml/bag of cement, including taking down existing cement plaster on brick walls or stone walls of any description etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of old surfaces of walls including washing down, rubbing, brooming down with wire brush scrapping down smoke, roots, moulds, salts and treading oil and greasy spots and applying two coats of white wash, complete all as specified and directed.

M&L for preparation of newly plastered surface of ceiling and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of old surfaces of ceiling including washing down, rubbing, brooming down with wire brush scrapping down smoke, roots, moulds, salts and treading oil and greasy spots and applying two coats of white wash, complete all as specified and directed.

M&L for preparation of old surfaces of walls of any description after complete removal of existing treatment and applying 2mm thick wall care putty for making the surfaces smooth and applying two coats of oil emulsion distemper, complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and making the surfaces smooth by applying 2mm thick wall care putty and applying two coats of oil emulsion distemper, complete all as specified and directed.

M&L for preparation of old surfaces of walls of any description after complete removal of existing treatment and making the surfaces smooth and applying two coats of cement base paint over a coat of alkali resistant primer including curing, complete all as specified and directed.

M&L for preparation of newly plastered surface of external wall and applying two coats of cement base paint over a coat of alkali resistant primer including curing, before and after painting complete all as specified and directed.

S&F 3mm thick plain sheet glass, ordinary quality and glazing with oil putty or fixed with beads / clips, in square not exc 0.50 Sqm in each pane, complete all as specified and directed.

S&F "as in repair" 3mm thick plain sheet glass, ordinary quality and glazing with oil putty or fixed with beads / clips, in square not exc 0.50 Sqm in each pane, complete all as specified and directed.

S&F 3mm thick figured sheet glass, ordinary quality and glazing with oil putty or fixed with beads / clips, in square not exc 0.50 Sqm in each pane, complete all as specified and directed.

M&L for preparation of old surfaces of steel & iron work of any description exc 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of old surfaces of wood & wooden of any description exc 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tank of capacity 1000 Litres, three layers (cylindrical vertical with closed top), hoisted and fixed in position including 20mm dia PVC ball valve, high pressure with polythene float complete all as specified in SSR Part-1, including dismantling of existing PVC water tank of any capacity complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tank of capacity 500 Litres, three layers (cylindrical vertical with closed top), hoisted and fixed in position including 20mm dia PVC ball valve, high pressure with polythene float complete all as specified in SSR Part-1, including dismantling of existing PVC water tank of any capacity complete all as specified and directed.

M&L for 15mm bore steel water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, including taking up or down existing steel water tubing and connections, complete all as specified and directed.

M&L for 20mm bore water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, including taking up or down existing steel water tubing and connections, complete all as specified and directed.

S&F in replacement 15mm bore chromium plated, fancy type stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S&F in replacement 15mm bore chromium plated, angular stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S&F "as in repair" 20mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F "as in repair" 15mm bore long body bib tap with flange, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F "as in repair" 15mm bore bib tap with flange, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F "as in repair" 15mm bore Pillar tap, cast copper alloy, fancy type, with capston head, chromium plated, screwed down, high pressure with or without letters, hot or cold with long screwed shank and fly nuts, screwed for iron pipe, complete all as specified and directed.

S&F "as in repair" towel rail chromium plated brass 600mm long, incl. fixing with SS screw and rawl plug complete all as specified and directed.

S&F in replacement PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

S&F "as in repair" CP soap nich fixed to walls with chromium plated brass screws complete all as specified and directed.

S&F in replacement health foucet hand shower 8mm dia, including 1.5mtr long flexible pipe, wall hook, complete all as specified and directed.

S&F stainless steel Grating doom 100mm dia fixed in floors complete all as specified and directed.

S&F stainless steel Grating doom 100mm dia with waste hole, fixed in floors complete all as specified and directed.

S&F Vitreous China urinals, flat back , bowl size 330mmx250mmx450mm white, including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) including spreader, CP coupling, waste pipe complete all as specified and directed.

S&F "as in repair" Vitreous china wash basin, white flat back of size 550mm x 400mm including 32mm size CP waste coupling full thread and 32mm dia PVC waste pipe, brackets and cutting for and pinning in ends of brackets or errecting stand, complete all as specified and directed.

S&F "as in repair" vitreous china wash down water closet pan (pedestal pattern), white including plastic white cover closed pattern with flat bottom and mild steel chromium plated hinging device including connections to drain or outgoing pipe and to flushing pipe anti syphonage pipe etc, complete all as specified and directed.

S&F "as in repair" Vitreous china squatting pan of 'Orissa pattern' of size 580mm x 440mm, white with CI ‘P’ or ‘S’ trap, front or back inlet and foot rests of any pattern (including fixing of flush pipe) and connecting etc. including provision of cement concrete bedding, complete all as specified and directed.

S&F "as in repair" PVC low level flushing cistern, valveless, syphonic action type, 10 litres capacity with inlet ball valve and handle with and including brackets and PVC bend pipe 60/90cm long etc, complete all as specified and directed.

S&F "as in repair" 75mm bore cast iron floor trap with stainless steel CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed.

S&F "as in repair" 75mm bore cast iron gully/nahani trap with stainless steel CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed.

M&L 100mm dia cast iron (sand cast) soil, waste vent pipes in any length with or without ears fixed with cement joints and tested including demolition and breaking up existing drain pipes set in cement mortar complete all as specified and directed.

M&L 75mm dia cast iron (sand cast) soil, waste vent pipes in any length with or without ears fixed with cement joints and tested including demolition and breaking up existing drain pipes set in cement mortar complete all as specified and directed.

M&L (sand cast) 100mm dia cast iron bends with ovel access door and jointed with neat cement paste complete all as specified and directed.

M&L (sand cast) 75mm dia cast iron bends with ovel access door and jointed with neat cement paste complete all as specified and directed.

M&L CI (sand cast) 100mm dia cowl cap complete all as specified and directed.

M&L for 100mm bore SGSW (Salt Glazed Stoneware) drain pipes, laid in trenches and jointed, including taking out old pipes of any description/ type complete all as specified and directed.

M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested in cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregates) for 100mm bore pipe, complete all as specified and directed.

M&L stack clamps made out of 50mm x5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100mm dia cast iron pipe complete all as specified and directed.

M&L stack clamps made out of 50mm x5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75mm dia cast iron pipe complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid or fixed in trenches / floors / walls, complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend, plain including jointing with solvent cement, complete all as specified and directed.

Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete and making good disturbed surfaces of walls, floors to match with existing specifications and keeping aside serviceable items for reuse within the same bldg and removing UNSV items from site, complete all as specified and directed.

M&L for modular point wiring for one light/fan/bell point controlled by one switch complete with 1.5 Sqmm multistranded FR PVC insulated unsheathed fire retardent copper conductor cable 1100 volts grade in and including non metallic rigid PVC heavy duty concealed conduit with wall thickness not less than 1.8mm including conduit accessories like bends, tees junction boxes etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sqmm single core FR PVC green insulated unsheathed multi stranded copper conductor 1100 Volts grade as earth continuity wire connected to earth dolly including inner and outer frame plate matching with surrouding with modular sunken steel boxes zinc oxide plated of suitable size including modular sheets of suitable module and back plates etc. complete all as specified and directed by Engineer-in-Charge.

Description all as per srl item No. 117.00 here-in-before but for 5 pin 5 amp socket outlet point on independent board controlled by one switch 5 Amps one way, etc complete all as specified and directed.

Description all as per srl item No. 117.00 here-in-before but for 5 pin 5 amp socket outlet point on same board controlled by one switch 5 Amps one way, etc complete all as specified and directed.

Description all as per Srl item No. 117.00 here-in before but for one 3/5 pin 15Amps socket outlet concealed using 2.5 Sqmm FR PVC insulated multi stranded copper conductor wire including 2.5 Sqmm FR PVC insulated unsheathed copper conductor earth wire and making good to disturbed surface of wall floor to match existing finishes etc complete all as specified and directed.

S&F modular socket outlet 6 Amp, 2/3 pin mutipurpose, 2 module complete all as specified and directed.

S&F modular socket outlet 5/15 Amp, 2/3 pin multi purpose, 2 module, complete all as specified and directed.

S&F modular switch 1 way 6 Amp, 1 module, complete all as specified and directed.

S&F modular switch 1 way 16 Amp, 1 module, complete all as specified and directed.

S&F lamp holder insulated body with back plate for batten fittings with polycarbonate body, including 9watt LED lamp complete all as specified and directed.

S&F ceiling rose surface bakelite 2 to 3 terminals 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F modular fan step regulator, step type suitable for 1200/1400mm sweep ceiling fan, hum free, 120W, 2 module, hum free and connecting electrically, complete all as specified and directed.

M&L for point wiring for one light point / fan point / bell point controlled by one switch with 1.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS cable and 1.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS (green colour) cable as earth lead drawn in and including connected non metallic rigid PVC conduit including CI/MS terminal box of required size including 3mm thick plastic laminated top sheet cover including cutting chases to walls and making good the disturbed surfaces to match with the existing specifications, complete all as specified and directed.

Description all as per srl item No. 128.00 here-in-before but for 5 pin 5 amp socket outlet point on independent board controlled by one switch 5 Amps one way, etc complete all as specified and directed.

Description all as per Srl item No. 128.00 here-in before but for one 3/5 pin 15Amps socket outlet on independent board using 2.5 Sqmm copper conductor FRLS cable, complete all as specified and directed.

S&F Switch piano flush button, single pole, one way, 5 Amps, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F "as in repair" Switch piano flush button, single pole, one way, 15 Amps, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F socket outlet, flush type 3 pin, 5 Amps, flush type 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F Socket outlet, 3 Pin, 5 and 15 Amps, multipurpose, 2 in 1, flush type, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F ceiling rose, surface bakelite, 3 terminals, 230 Volts AC with polycarbonate body, complete all as specified and directed.

M&L for submain wiring with two single core FR PVC insulated cable 2x6 sqmm (nominal dia) copper conductor (multistrand) and drawing in and including PVC concealed conduit pipe, ISI marked including 1x6 sqmm multistranded copper conductor FR PVC green insulated unsheathed cable for earth continuity, complete all as specified and directed. Note : Three runs of wire shall be measured as one unit.

S&F surface mounted 1x20 Watt LED tube light fittings (4 feet long), prewired, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, enviornmental friendly, energy saving efficient ready to use pack 20 Watt LED 6500 K and making connection using 3 core, 0.50 sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc, complete all as specified and directed.

S&F surface mounted 1x10 Watt LED tube light fittings (2 feet long), prewired, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, enviornmental friendly, energy saving efficient ready to use pack 20 Watt LED 6500 K and making connection using 3 core, 0.50 sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc, complete all as specified and directed.

Supply, fixing and testing "in replacement" of 20W energy saving LED Street Light luminaire. LED Street Light shall be made up of Pressure Die Cast aluminum housing with black epoxy polyester powder coating for long life and toughened glass visor fitted in frame, secondry optical lens for superior light distribution efficiency 100Lm/W making connections with street light/ building security light box or OH line using PVC insulated and sheathed single core multi stranded copper conductor cable of size 1.5 Sqmm including suitable size of brackets and light grade pipe for maintaining of fittings complete all as specified and directed.

Note for srl item No 138.00-140.00 above 1. Driver shall be potted anti-vibration types. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be provided. 3. CRI (Colour Rendering Index) of fixture shall be > 70. 4. CCT (Colour Co-related Temperature of fixture shall be 5700K + 300 K. 5. System Lumen Efficacy shall be > 100 Lm/W. 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 5 years guarantee shall be provided by contractor supported by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type. 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the contractor shall replace/repair the defective fitting within 07 days after handing over to contractor for replacement/repair. 11. CA No. shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintenance required, if any can be carried out from Top cover.

S&F in replacement of GI tubing light grade 40 mm bore cut to size and fixed along the pole for cable protection including clamp 02 Nos of size 25x4 mm, nut bolts , washers etc all as required at site including taking out old one complete all as specified and directed.

S&F "in replacement" sheet metal enclosure MCB distribution board, double door, single pole & neutral 240volts 08 way with IP-54 IK-09 protection complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification, complete all as specified and directed.

S&F "in replacement" sheet metal enclosure MCB distribution board, double door, triple pole & neutral 240volts 4 way with IP-54 IK-09 protection complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification, complete all as specified and directed.

S&F MCB single pole, 240 Volts, 6-32 Amps with repturing capacity 10 KA 'C' Curve complete all as specified and directed.

S&F MCB single pole and neutral, 240 Volts, 25 to 32 Amps with repturing capacity 10 KA 'C' Curve complete all as specified and directed.

S&F MCB Triple pole and neutral, 415 Volts, 40 Amps with repturing capacity 10 KA 'C' Curve complete all as specified and directed.

S&F electric water heater storage type, of capacity 25 ltr, BEE 5 star rated and including taking out existing water heater of any type and size and depositing to MES store yard etc, complete all as specified and directed.

S&F exhaust fans steel body with blade, frame, louvers and accessories 230volts, 450mm sweep, heavy dut,y five star rated including making connections using 3 core 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose to fan, including testing to ensure efficient functioning and including taking out existing exhaust fan of any type and size and depositing to MES store yard etc, complete all as specified and directed.

Taking down ceiling/exhaust fan, sealing cable end, dismantling blades and removing fan and blades and refixing and hanging ceiling fan back after repair including fixing of blades, and diagnosing the fault/defect by replacement of old burnt fan winding with new copper wiring, and including electric connection overhauling including minor repairs by replacement of capasitor, safety pin, cap, nuts & bolts etc and making connections using 3 core 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose to fan, including testing to ensure efficient functioning including application of one coat of synthetic enamel paint by spray painting & rewriting number complete all as specified and directed.

Supply and laying in trenches or fixed to wall/pole or passing through ducts or pipe, cable LT 1100 volts grade heavy duty, XLPE insulated , armoured heavy duty electric cable , with aluminium conductor of size 35 Sqmm x 3.5 core complete all as specified and directed. Note:- Excavation and earth work, sand cushioning, brick cover and protection pipe etc. shall be measured and paid for separately.

M&L for dry clean fine river sand as in sand cushioning to underground cable 8cm below and 15cm above the cable including punning down of sand layer complete all as specified and directed. Note :- Punned thickness shall only be measured and paid.

M&L for brick protection with sub class 'B' old size brick well burnt laid flat for cable protection abutting each other laid dry with width equal to length of brick complete all as specified and directed.

M&L for earthing complete with galvanised GI earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 Mtr deep below normal ground level) with top edge of earth plate not less than 1.5 Mtr below normal ground level, connected to galvanised earth lead wire 4mm dia by means bolt, nuts, check nuts and washer made of galvanised iron or steel including earth work in any type of soil, charcoal dust and salt layers 15cm thick all around the earth plate as shown in electrical plate No. 03 of SSR Part-I 2009 including 20mm bore GI watering pipe 'medium grade' with funel and wire mesh and 15mm bore GI protection pipe 'light grade' from earth pit to main board including PCC pit in cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) and including angle iron frame of size 40x40x3mm with hold fast embeded in PCC, RCC pit cover with suitable handle and earth work and removal of surplus soil to a distance not exc 50 Mtr, complete all as required at site and directed.

M/S CANTILEVER ENGINEERS

WALIA ENTERPRISES

Bidder Name

WALIA ENTERPRISES

RD Engineers

M/S CANTILEVER ENGINEERS