8519 PROVN OF GATE, FOOTPATH, FENCING AND ROAD SIDE SIGN BOARDS AT OLD NDA COMPLEX AREA AT PUNE UNDER GE (CENTRAL) PUNE

Amount

Excavation in trenches not exc 1.5m wide and n.exc 1.5m in depth for foundations, manholes etc and getting out in hard / dense soil.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm

Removal excavated soil n.exc 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete

M&L for cement concrete type D2 1:4:8 (using 40mm graded aggregates) in foundation, filling and mass concrete complete

M&L for TMT bar bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete.

M&L for TMT bar 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed.

M&L for formwork to flat rough finished sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work vertical or to batter complete.

M&L for formwork to flat rough finished sides of pillars, posts, struts, piers, columns, and stanchions complete.

M&L for reinforced cement concrete design mix M-25 as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete.

M&L for reinforced cement concrete design mix M-25 as in columns, pillars, piers, posts and struts complete.

M&L for precast cement concrete solid block typpe C1 (1:5:8) masonry, exc. 10 cm in width and setting in cement mortar 1:4 complete.

M&L, 20mm thick granite stone slabs over and including 15 mm thick screed layer in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of stone incl rubbing & polishing in cladding on gate pillars in double charge complete.

Surface dressing in soft/loose soil but n exc 15 cm deep.Complete all as sepecified and as directed.

M&L for hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete

M&L for 100mm plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of interlocking tiles complete all as specified and directed

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

Excavating in post holes in soft/loose soil (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete.

M&L for cement concrete type D2 1:4:8 (using 40mm graded aggregates) in foundation, filling and mass concrete complete.

S&F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing barbed wire etc) including all necessary drilling, bolting or riveting, embedding in cement concrete, MS flat at bottom etc and similar work confirminng to Fe-290 Gde E-165 complete

S&F MS flats (40x6mm) as bands, straps, supports or stays for securing chain link fencing to angle iron posts and welded to post in PCC during embedding complete

S&F for mild steel round bars 10mm dia and over, cut to length, bent to shape required conforming to Fe-410W Gde E-250 complete

S&F Mild steel screws bolts 11 to 15mm dia of neck (machine made) with hexagonal or square heads at one end and screwed at the other end, each screwed end to be fitted with washers and one hexagonal or square nut, n.exc 5 cm long and dia diameter of neck 5 to 10mm complete

Supply only chain link MS galvanised fencing any size or type (mesh size 50mm and dia of wire 4mm) complete

Fixing only chain link, fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire complete

S&F portions framed & hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks & similar work conforming to Fe 290-0 Gde E-165

M&L for preparation of new or previously untreated steel or iron surfaces of any description over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete. Note : PCC for fixing sign board shall be measured and paid seperately under relevant item of this schedule.

S&F retro reflective sign board of size 4' x 3' fixed both sides on stainless steel board made out of aluminium composite panel (ACP) sheet, 3mm thick fixed on SS-304 series hollow tubular section, 38mm dia. The board shall be provided with reflective tape of quality high intensity chequered type blue colour, letter/symbol shall be written in white colour writing of approved size/shape. The sign board shall be supported on 2 NOs post of 60mm dia stainless steel pipe, 304 series 3mtr long with round moulded design on top duly embedded in ground of size 450x450x600mm in PCC 1:2:4 type B-2 (using 40mm graded stone aggregate) including necessary excavation/earthwork etc as directed by Engineer-in-Charge.

S&F retro reflective sign board of size 3' x 2' fixed both sides on stainless steel board made out of aluminium composite panel (ACP) sheet, 3mm thick fixed on SS-304 series hollow tubular section, 38mm dia. The board shall be provided with reflective tape of quality high intensity chequered type blue colour, letter/symbol shall be written in white colour writing of approved size/shape. The sign board shall be supported on 1 NO post of 60mm dia stainless steel pipe, 304 series 3mtr long with round moulded design on top duly embedded in ground of size 450x450x600mm in PCC 1:2:4 type B-2 (using 40mm graded stone aggregate) including necessary excavation/earthwork etc as directed by Engineer-in-Charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6.0 sq mm 2 core complete all as specified and directed. Note : The quoted rate shall include lugs for termination as sper site requirement.

Excavation in trenches, not exc 1.5 mtr wide and not exc 1.5 mtr in depth for laying of HT UG cable/poles in soil/rock as mentioned below type of soil and getting out complete all as specified.

(a) soft/loose soil

(b) hard/ dense soil

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm as in soil all as specified & directed

Removing excavated material (soil / disintegrated rock) to a distance n.exc 50m and depositing where directed at level not exceeding 1.5m above the starting point all as specified & directed.

M&L for laying of RCC pipe lines of dia 150mm class NP2 with one collar per length of pipe, 2 Nos half round (for bottom and top) and before laying excavation of area shall be levelled all as specified and directed.

Supply and lay/ fix on wall GI pipe of 25mm light grade complete all as specified and directed

M & L for Cutting of road/hard standing and making good with PCC (1:2:4) using 20mm graded stone aggregate complete all as specified.

Supply and fix lamp post top 25W, IP 65 aluminium landscape luminare , opal cover complete all as specified and directed

Supply and fix syntex box 155X155X100mm consisting of MCB 10A C curve 10KA 240V, insulator base 3 pin contactor with all necessary accessories such as clamps and nuts as per site requirement complete all as specified and directed

Supply and fix syntex box 103X103X73mm consisting of MCB 10A C curve 10KA 240V, insulator base 3 pin contactor with all necessary accessories such as clamps and nuts as per site requirement complete all as specified and directed

S&F Sub main wiring with 2 runs of single core, 2.5 Sqmm PVC insulated, unsheathed, 1100 volts grade multi-stranded, copper conductor cables (FRLS H) drawn through PVC casing capping with fitting/accessories, fixed on roof, walls, ceiling etc including 2.5 Sqmm PVC insulated, unsheathed, single core, multistranded, copper conductor as earth continuity wire complete as specified and directed. Note : Rate includes (i) PVC casing capping and its accessories (ii) Two runs of cable and one run of earth wire of size 2.5 sqmm

Agarwal Agencies (BID ID -3132480)

PRANAV ENTERPRISES (BID ID -3121154)

SAI TILES ARTS (BID ID -3132559)

SARATH ENTERPRISES (BID ID -3128777)

Vijay Construction and Company (BID ID -3123135)

M/s.BAJRANG CONSTRUCTION (BID ID -3120711)

M/S - R K CONSTRUCTIONS (BID ID -3132297)

ANIL CONSTRUCTION CO. (BID ID -3123406)

M/s Asrani and sons (BID ID -3123810)