PETTY REPAIR TO CERTAIN BLDG AND REPAIR MAINT OF ROOF LEAKAGE SEAPAGE AND ROOF TREATMENT TO CERTAIN BLDGS AT BAIRAGARH UNDER GE BHOPAL

Amount

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Taking down cement plaster on brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc

M&L for 15mm thick rendering in CM 1:6 on fair faces of brick/concrete surfaces finished even and smooth with out using extra cement complete all as specified and directed.

M&L for 5 mm thick rendering in CM 1:3 on fair face of brick/ concrete surfaces as in ceiling complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories) complete all as specified and directed.

S&F 75 mm PVC (SWR) pipes Single socketed in any length with rubber rings joints laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) 110mm pipes Single socketed in any length with rubber rings joints laid in trenches or in floors complete all as specified and directed.

S&F 75mm PVC (SWR) bend complete all as specified and directed.

S&F 75mm PVC (SWR) junction single (single 'T') equal or unequal complete all as specified and directed.

S&F 75mm PVC (SWR) vent cowl complete all as specified and directed.

S&F 110mm PVC (SWR) vent cowl complete all as specified and directed.

M&L for PVC (SWR) floor trap plain with grating incl jointing with solvent cement 75mm bore complete all as specified and directed.

S&F PVC (SWR) 110 mm bend complete all as specified and directed.

Taking down chowkats or frames exc 1.50 Sqm but n.exc 4 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frames n exc 1.50 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down shutters of any descripition exc 1sqm and n exc 2sqm each and removing to or from store complete all as specified and directed.

Easing of door shutters for easy closing / opening tightening of hinges or changing the position of hinges adjustment of tower bolts, sliding bolts with new screws etc complete all as specified and directed.

Easing of window shutters, kitchen cupboard shutters, show case shutter drawers incl fixing of screws adjusting handles, knobs tightening piano hinges incl misc small adjustments complete all as specified and directed.

Taking down shutters of any description and refixing in the same opening exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F 15 mm bore GI tubing medium grade, galvanised with all fitting and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified and directed.

S&F 20 mm bore GI tubing medium grade, galvanised with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Demolition of brick work or stone masonery built in cement mortar complete all as specified and directed.

M&L for brick work with modular size fly ash bricks, straight or curved on plan to any radius in half brick thick walls build in CM 1:4 complete all as specified and directed.

M&L for brick work with modular size fly ash bricks in CM 1:6 straight or curved on plan to any radius complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings (un reinforced) nexc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 18-20mm thick o laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & mirror polishing over and including Screed bed or beding layer of mortar 15mm thick for laying floor finish in CM 1:4 complete all as specified and directed.

-Ditto- but for dados and similar work as in skirting 18-20mm thick kota stone complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, 75mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 25mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate) as in floors complete all as specified and directed

M&L for vitrified light shade tiles 8 to 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc, set and jointed in neat cment slurry and pointed in white or coloured cement to match over and including Screed bed or beding layer of mortar 15mm thick for laying floor finish in CM 1:4 complete all as specified and directed.

M&L for vitrified light shade tiles 8 to 10 mm thick (Square/rectangular) polished, area of each tile not exceeding 0.36 sqm, as in vertical surfaces such as skirting, risers to steps, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over and including rendering 10mm thick backing coat to wall tile in CM 1:3 with complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (Square/Rectangular) area of each tile exe 0.11 Sqm but not exe 0.18 sqm in floors etc. set and jointed in cement slurry and pointed with white or coloured cement to match over and including Screed bed or beding layer of mortar 15mm thick for laying floor finish in CM 1:4 complete all as specified and directed.

All as per item No 35 above but on vertical surface over and including rendering 10mm thick backing coat to wall tile in CM 1:3 complete all as specified and directed.

M&L for glazed ceramic tiles in vertical surfaces 350x250x7mm/ 450x350x7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including rendering 10mm thick backing coat to wall tile in CM 1:3 complete all as specified and directed.

M&L for Granite work 18-20 mm thick (of any type/ colour) (table rubbed and polished/ moulding) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing n white cement (1:2) using marble dust with admixture of pigment to match with shade or granite over and including screed bed or beding layer of mortar 15mm thick for laying floor finish in CM 1:4 complete all as specified and directed.

M&L for Endura joint free coloured tiles 8 to 10 mm thick (square/rectangular) area of each tiles not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles over and including screed bed or beding layer of mortar 15mm thick for laying floor finish in CM 1:4 complete all as specified and directed.

Supplying, fabricating and fixing powder coated (minimum thickness 50 micron) aluminium sections of required size for door windows frames shutters and partitions including aluminium hinges of required size jointing cleats, screws sash fasteners, plug for fixing with walls, columns, etc complete all as specified and directed.

Hacking out old broken glass (any thickness quality or description) from from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

S&F 3mm thick plain sheet glass ordinary quality nexc 0.50 Sqm in each pane complete all as specified and directed.

S&F 4.0mm thick plain sheet glass ordinary quality n exc 0.50 Sqm in each pane complete all as specified and directed.

S&F 4.0 mm thick plain sheet glass ordinary quality exc 0.50Sqm in each pane complete all as specified and directed.

M&L for 2nd class hardwood plain fillets, square, rectangular or triangular in section, wrought, fixed with nails, cross sectional area exceeding 13 sqcm but not exceeding 25 sqcm, complete all as specified and directed.

M&L for factory made, second class hardwood 30mm thick plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and directed.

S&F IInd class HW factory made 30 mm thick glazed and skelton shutter, open rebated and prepared to receive glass, gauges, etc ( with or without sash bars) , edges of framing plain, chamfered or rounded, fitted with cut and mitreated beads for securing glass, etc fixed to chowkats complete all as specified and directed.

S&F 35 mm thick flush shutters, solid core construction, with block board core and ply wood face panels, commercial type on both sides complete and fixed to chowkats complete all as specified and directed.

S&F Solid PVC Door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top & bottom rails. MS frame shall be covered with heat moulded palin colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame wlded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing tin the frame at site complete all as specified and directed.

S&F Factory made solid PVC moulded door shutter with particle board core 28 to 30mm thick (style) with 2, 4 or 6 raised panel design with 2mm thick 3D plain colour PVC sheet on the front face and 2 mm plain colour PC sheet on back face complete all as specified and directed.

S&F Butt hinges 100mm, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F Butt hinges 100mm size medium weight cold rolled mild steel complete all as specified and directed.

ditto- but 125 mm long complete all as specified and directed.

S&F 150 mm long aluminium handles, cast type, anodised fixed to shutters complete all as specified and directed.

S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed to frames complete all as specified and directed.

S&F in repair to Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed to frames complete all as specified and directed.

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

S&F 300mm, ordinary MS rat tail rod pattern springs including roller and roller plate with welding complete all as specified and directed.

S&F in repair 20mm Stainless Steel Drepary curtain rod decorative type incl curtain fancy type bracket & nobs complete all as specified and directed.

Dismantling wall and ceiling boards of any description fixed in any position, any thickness including cover fillets complete all as specified and directed.

S&F galvanised cold rolled steel section framed work size 600x600mm grid size 24x38x0.60mm Tee (bottom precoated) and 24x24x0.50mm thick wall angle galvanised cold rolled steel section incl expansions fasteners as in ceiling complete all as specified and directed. (Make : Gabson or equivalent as approved by GE)

S&F 4mm thick Exposed metal frame ceiling with decorative type calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 595 mm x 595 mm grid complete all as specified and directed. (Frame work for ceiling shall be measured and paid separately)

S&F 40mm wide of flap continuous (piano) hinges, brass, bright finish complete all as specified and directed.

S&F in repair Block board 18/19 mm thick, exterior grade, prelaminated both side with decorative choice lamination fixed with nails to complete all as specified and directed.

S&F 100 mm Stainless steel handle, cast type, polished bright complete all as specified and directed.

S&F in repairs Vitreous china squatting pan ‘Orissa’ pattern, ISI marked, size 580 x 440 mm, white with integral foot rests including provision of cement concrete bedding & ‘P’ or ‘S’ trap complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan, pedestal pattern, ISI marked, white, including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F in repairs PVC low level flushing cistern 10 litres capacity, ISI marked, white, with all fitting and fixtures including brackets, PVC connection of 450mm long and 32 mm bore PVC flush pipe, complete all as specified and directed.

S&F in repairs Vitreous china wash hand basin white flat back of size 550 x 400mm excluding tap but including brackets/CP brass 32mm waste coupling complete all as specified and directed.

S&F in repairs bathroom cabinet of hard thermosetting plastic of size 500 x 400 mm, fitted with superior quality distortion free 4 mm thick mirror complete all as specified and directed.

S&F in repairs Stainless steel sink, 1.00mm thick for kitchen, with plug, washers and wastes/coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm with bowl size 410mmx 330mmx 160mm fixed complete all as specified and directed.

S&F in repairs 15 mm Angle valve stopcock cast copper alloy, screwed down high pressure chromium plated screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs 15 mm bib taps cast copper alloy, screwed down high pressure chromium plated screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair 32mm bore PVC waste pipe for wash basin one mtr long complete all as specified and directed.

S&F in repairs 15 mm pillar taps cast copper alloy, with capstain head chromium plated screw down high pressure, with or without lettered HOT or Cold with long shanks and fly-nuts screwed for iron pipes and fixed complete all as specified and directed.

S&F Jet spray SS (butterfly) with 1 mtr tube complete all as specified and directed. [MAKE:- Prayag (Cat No.BEA-18) or equivalent in MARC/ JAQUAR

S&F in repairs CP Waste Coupling, (half or full threaded) 32 mm dia size made of cast copper alloy, complete all as specified and directed.

S&F 15 mm size wash basin mixutre, centre hole, mixing hot & cold water, fancy type, cast copper alloy, chromimum plated with capstan head, chromium plated, screwed down high pressure, screwed for iron pipe etc and fixed in repairs complete all as specified and directed.

S&F hand shower (health faucet) brass with 1.0 mter long flexible tube and wall hook complete all as specified and directed. MAKE:- Prayag / MARC/ Hindware

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450 mm complete all as specified and directed. MAKE:- Prayag / MARC/ Hindware

S&F in repairs PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and directed. MAKE:- Prayag / MARC/ Hindware

S&F in repairs Plastic water closet seat cover, any colour, closed pattern with flat bottom, and mild steel chromium plated for aluminised hinging device complete all as specified and directed. MAKE:- Prayag / MARC/ Hindware

S&F tubular towel rail chromium plated 20 mm dia D type 60 cm long between flanges complete all as specified and directed. MAKE:- Prayag / MARC/ Hindware

S&F in repairs 6” overhead shower with 300mm arm & flange complete all as specified and directed. MAKE:- Prayag / MARC/ Hindware

S&F in repairs wall mixture non-telephonic with crutch for mixing hot & cold water, fancy type, chromium plated, screwed for iron pipe or for unions 15mm bore, complete all as specified and directed. MAKE:- Prayag / MARC/ Hindware

S&F 15 mm bib cock two way with flange, cast copper alloy, fancy type, chromium plated screwed down for iron pipe and fixed in repairs complete all as specified and directed. MAKE:- Prayag / MARC/ Hindware

S&F 15 mm Angle valve two way with flange, cast copper alloy, fancy type, chromium plated screwed down for iron pipe and fixed in repairs complete all as specified and directed. MAKE:- Prayag / MARC/ Hindware

Dismantling Asbestos cement (Corrugated, semi corrugated, etc) sheets including ridges in roof covering complete all as specified and directed.

Dismantling timber in fillets rails, posts, rafters, purlins, etc under 40 Sqcm in section unframed work complete all as specified and directed.

M&L for preparation of New or previouly untreated surface of steel and iron surface of any description and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.5mm thickness, 150 Az, of colour as approved by GE, having tensile strength of 550 Mpa as in roof coverings/cladding to wall, etc, fixed with & including self tapping screws on angle frame complete all as specified and directed. [MAKE: TATA / JSW/ EVEREST]

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet, 0.5mm thickness, 150 Az, of colour as approved by GE, having tensile strength of 550 Mpa as in ridges, etc, fixed with & including self tapping screws complete all as specified and directed. [MAKE: TATA / JSW/ EVEREST]

M&L for 2 mm thick Fibre glass reinforced translucent Plain sheeting with sid lap fixed with L type or J type or cranked hook bolts complete all as specified and directed.

S&F Steel work in tubular/structural trusses, purlins, etc including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 or steel sections conforming to Fe 410-W (Gde E-250) quality -A complete all as specified and directed.

S&F Mild steel conforming to Fe-290 Gde E-165 in bands, straps, supports or stays for rain water, including bolts, if required, hook and pintle hinges; handmade sliding bolts; clamps; hold fasts; hooks for hanging fans and similar small articles complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12.5 cm wide with chromium plated bracket guard and railing 50 cm long complete all as specified and directed. [MAKE:- Prayag (Cat No.BEA-45) or equivalent in JAQUAR/CERA as approve by GE]

S&F in repairs corner glass shelf assembly consisting of 5.5 mm thick sheet glass shelf with chromium plated bracket guard and railing 300mm size complete all as specified and directed. [MAKE:- Prayag (Cat No.BEA-46) or equivalent in JAGUAR/CERA/ make as per Appx 'C' (list of make) as approved by GE]

M&L for grinding and polishing of kota/marble/terazoo/mosaic flooring complete all as specified and directed.

Dismantling water tanks of Exc 500 litres but n exc 1000 litre capacity and removing to store complete all as specified and directed.

S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed.

S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed.

S&F 20 mm dia ball valve PTMT, high pressure with polythene float and fly nut complete, screwed for iron pipe with epoxy coated aluminium rod complete all as specified and directed.

S&F in repairs gunmental, globe or gate valves 20 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair stainless steel plate rack complete assembeled set of (Size: 31 x 36 x 10 inch) fixed with screws complete all as specified and directed.

S&F in repair stainless steel plate rack complete assembeled set of (Size: 24 x 30 x 10 inch) fixed with screws complete all as specified and directed.

S&F in repairs towel rack 24" long with hanger, brass chromium plated fixed to walls with chromium plated brass screws complete all as specified and directed.

S&F 105*60 mm pressed steel frames for doors with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate, etc. complete as specified made out of 1.25mm thick ms sheet complete all as specified and directed

S&F 125*60 mm pressed steel frames for doors with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate, etc. complete as specified made out of 1.25mm thick ms sheet complete all as specified and directed

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass,other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F in repair Aluminium (Extruded section body ) Door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete all as specified and directed.

M&L for Cabinet Hinges Soft Close SS 8 Crank complete all as specified and directed

Taking down existing aluminium door shutter with frame area exceeding 1 Sqm and re-fixing in same opening after repair/replace complete all as specified and directed. Note :- The defective parts of any type of aluminium section will be measured and paid separately.

S&F in repairs PVC float set for flushing cistern of 10 Ltr capacity complete all as specified and directed. [Make:- Prayag/Cera/Hindustan/HR Johnson as approved by GE]

S&F in repairs good quality rubber washer for flushing cistern of 10 Ltr capacity complete all as specified and directed. [Make:- Prayag/Cera/Hindustan/HR Johnson as approved by GE]

S&F in repairs good quality PVC syphone for 10 Ltr capacity complete all as specified and directed. [Make:- Prayag/Cera/Hindustan/HR Johnson as approved by GE]

S&F in repairs flexible PVC waste pipe 32 mm bore suitable for wash basin, etc complete all as specified and directed.

S&F in repairs flexible PVC waste pipe 40 mm bore suitable for kitchen sink, etc complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x complete all as specified and directed.

S&F in repair CP waste coupling 40mm suitable size for kitchen sink of PTMT (half or full threaded) complete all as specified and directed

S&F in repairs 15 mm bore bib taps standard of PTMT any colour screwed, for iron pipe and fixed (Minimum weight 15mm 90gms) complete all as specified & directed

S&F in repairs 15 mm bore Pillar tap standard of PTMT any colour screwed, for iron pipe and fixed (Minimum weight 15mm 110 gms) complete all as specified & directed

S&F in repairs 15 mm bore angle valve standard of PTMT any colour screwed, for iron pipe and fixed (Minimum weight 15mm 90gms) complete all as specified & directed

S&F in repairs 15 mm bore stop valve standard of PTMT any colour screwed, for iron pipe and fixed (Minimum weight 15mm: 90gms) complete all as specified & directed

Opening of air lock/bockage in GI pipe line from outlet of OH water tank to internal GI pipes/fittings to obtain smooth & full flow of water by air /gravity pressure from bib taps/ pillar taps/over head shower, etc complete all as specified and directed.

S&F in repairs 40 mm dia, cupboard knobs fixed with nut, screws and washers of mild steel, bright finished complete all as specified and directed.

S&F in repairs Stainless steel peg sets of 3 Nos pegs, heavy quality complete all as specified and directed.

S&F in repairs Stainless steel peg sets of 6 Nos pegs, heavy quality complete all as specified and directed.

Preparation of old decorated surfaces of wall including brooming, scraping down. Smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails marks and one coat of white wash on walls complete all as specified and directed.

All as per item No. 131.00 above but on ceiling complete all as specified and directed.

M&L for complete removal of old decorated surface of wall and applying two coat of oil emulsion distemper white/coloured over and one coat of white cement based putty (where it is required) all as specified and directed by Engr-in-Charge. Note:- Putty shall be measured and paid seperately.

M&L for Preparation of old decorated surfaces of wall including brooming, scraping down, smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails marks and apply one coat of oil emulsion distemper all as specified and directed.

M&L for Preparation of old painted surfaces of wood/wood based materials exc 10cm width or girth and applying one coat of synthetic enamel paint as directed and specified.

All as per item No. 135.00 above but on steel surfaces.

Preparing new plastered or unplastered surfaces of wall and M&L for applying two coats of exterior acrylic emulsion paint, white or tinted over and including a coat of exterior wall primer on plastered surfaces complete all as specified and directed. [Make :Shalimar(Saktiman) / Asian(ACE) / Burger(wall masta)]

M&L for one coat of 3mm thick wall care putty on walls/ceiling all as specified and directed

M&L for preparation of newly plastered surface of ceiling by brooming down and applying one three coat of white wash complete

Preparing new plastered or un-plastered surfaces of wall and M&L for applying two coats of exterior acrylic emulsion weather coat paint, white or tinted complete all as specified and directed. [Make:- Apex Paint of M/s Asian Paints or equivalent in M/s Berger or M/s ICI as approved by GE] NOTE:- (a) 3mm thick wall care cement putty where ever required shall be measured & paid separately. (b) The work of applying exterior acrylic emulsion paint shall be carried out by authorized representative/applicator of the manufacturer. (c) A Guarantee of 5 yrs from the certified date of completion for the effectiveness of exterior acrylic emulsion weather coat paint shall be submitted by the manufacturer and contractor. (d) A Security deposit @2.5% of the amount of treatment shall be deposited by the contractor for the entire guarantee period i.e. 5 yrs in the form of FDR in favour of GE. (e) During the guarantee period if exterior acrylic emulsion weather coat paint gets removed or becomes layered contractor shall rectify or replace (at his option) defective materials at his own expenses, when called upon in writing to do so by the GE. Condition 46 of IAFW-2249 (defects liability period) for the guarantee period shall be deemed amended accordingly for the work..

M&L for preparation of newly plastered surface of wall and and applying two coat of oil emulsion distemper white/coloured over and including one coat of white cement based putty (where it is required) all as specified and directed by Engr-in-Charge. Note:- Putty shall be measured and paid seperately under the relevent item

S&F kitchen baskets with 100 % stainless steel ,non - magnatic, multilayer chrome plated , argon welded ,double sealed ball bearing mechanism kitchen capable of holding plates ,cup ,saucers,bowls and dongas with 500 mm car case depth of 558mm and height 100mm complete all as specified and directed. Make Life time -code : DSN 21 or equivalant

S&F kitchen baskets with 100 % stainless steel ,non - magnatic, multilayer chrome plated , argon welded ,double sealed ball bearing mechanism kitchen capable of holding plates ,cup ,saucers,bowls and dongas with 500 mm car case depth of 558mm and height 150mm complete all as specified and directed. Make Life time -code : DSN 21 or equivalant

S&F kitchen baskets with 100 % stainless steel ,non - magnatic, multilayer chrome plated , argon welded ,double sealed ball bearing mechanism kitchen capable of holding plates ,cup ,saucers,bowls and dongas with 500 mm car case depth of 558mm and height 200mm complete all as specified and directed. Make Life time -code : DSN 21 or equivalant

S&F in repair to Telescopic Drawer Channel soft close20''-Inch in length for kicten basket complete all as specified and directed make :- Hettich or equivalent

S&F in repair to magnetic catcher for cupboard shutter complete all as specified and directed make :- Hettich or equivalent

Disconnecting exc 250 and n exc. 500 ltrs existing tanks, setting aside (for lowering if required) for repairs cleaning and removing all scale and dirt, etc from tanks and mouths of circulating pipes etc and hoisting if required reconnecting and re-fixing in position complete all as spfd and directed.

Taking down existing old roof treatment of any description, any type including removal old Tar felt, screed bed and plastering etc complete all as specified and directed.

M&L for 10 mm thick rendering in CM 1:4 mixed with integral water proofing compound @3% by weight of cement applied over roof slab. (Water proofing compound shall be measured and paid seperately)

M&L for Water proofing treatment on roof surfaces with APP modified membrane with non woven polyester reinforced, weight not less than 3 KG/SQM and thickness of membrane not less than 3mm (plain/ thermal insulation with white mineral/gravel finish on upper side of membrane as per site requirement as directed by Engr in Charge) uniformly embedded during manufacturing process laid in following sequence complete all as specified and directed.:- (a) Applying 10mm thick plaster in CM 1:4 mixed with water proofing compound @ 3% by weight of cement on cleaned roof surface.(Plastering shall be measured and paid under item No 149.00 above) After properly curing of the plaster, the roof will be tested for water tightening by ponding with water for seven days for any seepage/leakages, etc. If any seepage/leakage is observed the rectification will be carried out by pressure grouting under pressure of 5 Kg/sqcm using cement based grout. After the roof surface is repaired, the slab /roof will be again tested for water tightness before proceeding for further treatment. (b) Properly cleaning and drying of the plastered roof surfaces, parapets, gutters, drain mouths, etc for all foreign matters such as fungus, moss, dust, etc by wire brushing and dusting. Proper grooves shall be cut around CI drain outlets/pipes/chimney pipes and other similar situations to tuck in the treatment. (c) Applying one coat of hot bitumen grade 85/25@ 1.2Kg/Sqm on the prepared surface till the surface is properly impregnated. (d) Laying APP modified water proofing membrane with 100mm overlap in longitudinal direction and 100mm overlap in transverse direction sealed and bounded to the surface by torch application method. (e) All joints and changes in direction should be curved with cement mortar 1:3 with SBR latex @ 200ml per bag of cement and cured well before laying the membrane. A fillet of PCC 1:2:4 type B0 using 12.5mm graded stone aggregates shall be provided at all junctions of vertical and horizontal surfaces and wherever there is change of direction.

Supply only Integral water profing compound mixed with cement mortar complete all as specified and directed.

Refixing old 20 mm GI tube medium grade with all necessary new fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

Refixing 15 mm GI tube medium grade with all necessary new fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

M&L for for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with PU material all as specified and directed.(Make -Fosroc)

M&L for precast machine pressed cement concrete tiles with grey cement and no pigments of size 250x250x20 - 25mm thick conforming to IS 1237-1980 set in cement slurry laid jointed and pointed in neat cement slurry including bedding layer of 15mm thick screed in CM 1:4 as in roof complete all as specified & directed.

M&L for Providing Cement concrete Type B1, 1:2:4 (20mm graded aggregate) as in roof padding, kerbs or mud stops, copings and levelling concrete slightly rounded or chamfered angles and throating complete all as specified & directed.

M & L for rendering 15mm thick in CM 1:3 on fair faces of brick work, concrete surfaces as in sunken / roof treatment finished even and smooth including removing loose concrete/plaster from chajjas, parapets, fascia, pillars, columns etc complete all as specified & directed.

M&L for grouting of structural damage /crack of RCC structure with cement by mixing 1 % SALIGROUT IP by wt of cement which is plasticized and non shrink cement mortor admixture for pressure injection gruting by drilling, fixing with nozzle pvc and ceiling of the same after the grout is injected treatment to be made as per manufacyring insruction including material required complete all as specified ( Make - Fosroc /STP

M&L for repairsto seapage from wall/ chajja by Preparation to affected wall, chajja portion on plastered and unplastered surface, cleaning by brush cloth and applying one coat of white base water proofing acrylic coating on wall by use brush /tools on walls by coverage over 3.7 to 4.1 sqm / litre as per manufacturers instructions complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on brick/concrete/stone masonry surfaces including finishing the surfaces even and smooth (without using extra cement) complete all as specified and directed.

Dismantling water tank capacity exc 250 ltrs but nexc 500 ltrs and removingfrom site complete all as specified and directed

S&F in repair 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

Deduct schedule of credit (calculation will be done off line) Rs. 60,835.00

Samaksh Enterprises

M/s VIKAS TRADERS

M/S Shanti Traders