Construction of District Hospital at Garacharma.Develipment of site

Amount

Disposal of moorum/building rubbish/ malba/similar unserviceable, dismantled or waste material by mechanical transport including loading transporting, unloading to approved municipal dumping ground for lead upto 5 km for all lifts, complete per directions of Engineer-in-charge.

Carriage of earth by mechanical transport including loading, unloading and stacking at site lead of 5 km.

Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.

All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Extra for excavating trenches for pipes, cables etc. in all kinds of soils for depth exceeding 1.5m, but not exceeding 3m.(Rate is over corresponding basic item for depth upto 1.5 metre).

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.

All kinds of soil

Extra for levelling & neatly dressing of disposed soil completely as directed by Engineer-in-Charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :

1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20 mm nominal size).

1:2:4 (1 Cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 40 mm nominal size).

1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling and dressing and finishing the top smooth.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level :

1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete Above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and filling in position, blown bitumen in expansion joints.

Providing and filling in position bitumen mix filler of proportion 80 kg. of hot bitumen, 1 kg. of cement and 0.25 cubic metre of coarse sand for expansion joints.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including:

(a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing. The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items.

The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approvedshop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Approved cramps/ pins etc. shall be welded to the frame work to support stone cladding, the steel work will be given a priming coat of Zinc primer as approved by Engineerin- charge and painted with two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer-in-charge for approval before execution).

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, panelling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing.

30 mm thick plain PVC door shutters.

Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

80x1.25 mm M.S. laths with 1.25 mm thick top cover.

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.

G.I. pipes

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with :

4.0 mm thick glass panes.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

40 mm thick with 20 mm nominal size stone aggregate

Chequerred precast cement concrete tiles 22 mm thick in footpath &courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).

Dark shade pigment using ordinary cement.

Extra for providing and fixing wind ties of 40x 6mm flat iron section.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500-600mm)

Barge board (Upto 300 mm).

Gutter (600 mm over all girth).

12 mm cement plaster of mix :

1:4 (1 cement : 4 fine sand)

1:6 (1 cement: 6 fine sand)

12 mm cement plaster finished with a floating coat of neat cement of mix :

1:3 (1 cement: 3 fine sand)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :

Water thinnable cement primer.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade

New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work.

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade :

Two or more coats on new work.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre. of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.

Two coats.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm. depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Providing and applying tack coat using hot straight run bitumen of grade VG - 10 including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications :

On W.B.M. @ 0.75 Kg / sqm.

On bituminous surface @ 0.50 Kg / sqm.

2 cm premix carpet surfacing with 1.8cum and 0.90cum of stone chippings of 13.2mm size and 11.2mm size respectively per 100sqm and 42.64kg of hot bitumen + 4.16kg shredded plastic and 45.92 kg of hot bitumen + 4.48 kg shredded plastic per cum of stone chippings of 13.2mm and 11.2mm size respectively, including a tack coat with hot straight run bitumen, including consolidation with road roller of 6 to 9 tonne capacity etc. complete (tack coat to be paid for separately).

With paving Asphalt grade VG - 30 with no solvent

Providing and laying seal coat of premixed fine aggregate ( passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG - 10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface including rolling and finishing with road roller all complete.

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.

Extra for providing and mixing hardening compound of approved quality as per manufacturer's specification in cement concrete.

Painting road surface marking with adequate nos of coats to give uniform finish with ready mixed road marking paint conforming to IS : 164, on bituminous surface in white/yellow shade including cleaning the surface of all dirt, scales, oil, grease and foreign material etc. complete.

New work (Two or more coats).

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer in-Charge.

80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe

40 mm dia

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :

100 mm inlet and 100 mm outlet

Sand Cast Iron S&S as per IS: 1729.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design :

With 20x20 mm square bar

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality

Circular shape 560 mm internal diameter

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

NEXT GENERATION CROSSWAVE RAINWATER HARVESTING SYSTEM

S & F Non woven Geo textile having thickness of 400 gsm, having minimum tear strength of 250 ASTM D4533, width wise atleast 215 ASTM D4533 having puncture strength of 1550 plus as per ASTM D6241 having elongation at break % of 57 plus as per ASTM D4595 in two layers, made out of long fibres to hold the modules and protect liner including cutting, sizing, head welding and needle punched for high porosity and proper percolation complete.

S & F Co-polymer /polymer based rainwater harvesting structure comprising crosswave of each piece having a size of 494mm x 494mm x 220mm with minimum void ratio of 94.7% having a weight of 1.8 kg each and spacers having size of 988mm x 240mm x 25mm having a weight of 0.8 kg each and arranging the same as directed by the Engineer-in-charge and in complete accordance to the design, drawings of the manufactures

S & F Central ground water bond (CGWB)/ Green rating for integrated habitate assesment (GRIHA) approved pure rain filter 700mm dia. With 300mm dia. Inlet and outlet to accommodate storm water having desalting suspended solid catcher made out of FRP with stainless steel 304 grade strainers having stainless steel bucket of 600 micron capable of eliminating finer particular matter upto 160 micron filtration made of stainless steel net with long fibre foam of 25mm thickness, filtration capacity 40-80 kilolitres per hour complete in accordance to the manufactures design, drawing and specification and complete all as specified and as directed by Engineer-in-charge. The total depth of filter shall be 2000mm. The make shall be all as approved by GE.

S & F HDPE high EVA liner having thickness of 1.2mm for the collection of water heat welding onsite and offsite as pe the requirement complete

Supplying and fixing FRP based access inspection chambers of minimum size of 500mm x 500mm x 500mm complete as per the direction of engineer-in-charge

Providing and laying factory made Precast concrete solid blocks of 200 mm thickness of mix 1:3:6 laid in cement mortor 1:6 from approved manufacturer in foundation and plinth in:

Providing and laying antiskid Ceramic floor tiles 300x300mm (thickness to be specified by the manufacturer) of 1st quality coforming to IS:15622 of approved make in all colours, shades, except White, Ivory, Grey, Fume Red Brown laid on 20mm thick bed of Cement Mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing PVC moulded corner beading of triangular shape to the junction of panelling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete.

Providing cement concret surface drain with 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate of 40 mm nominal size) finished with cemnet mortar 1: 4 (1cement : 4 coarse sand) including floating coat of neat cement, slurry inside the drain and its top and exposed surface including earthwork in excavation and disposing of surplus earth etc. complete.

Surface drain 23cm x 23cm

Surface drain 30cm x 30cm

Providing and laying hollow cement concrete block walling consisting of hollow block of size 400x200x200mm of mix 1:3:6 (1 cement : 3 coarse sand: 6 graded stone aggregate 10mm nominal size) laid in cement mortar 1:6 (1 cement : 6 coarse sand) upto floor five level.

Hollow Block walling 200 mm

Providing and laying hollow cement concrete block walling consisting of hollow block of size 400x200x150mm of mix 1:3:6 (1 cement : 3 coarse sand: 6 graded stone aggregate 10mm nominal size) laid in cement mortar 1:6 (1 cement : 6 coarse sand) upto floor five level.

Hollow Block walling 150 mm

Providing and laying hollow cement concrete block walling consisting of hollow block of size 400x100x200mm of mix 1:3:6 (1 cement : 3 coarse sand: 6 graded stone aggregate 10mm nominal size) laid in cement mortar 1:6 (1 cement : 6 coarse sand) upto floor five level.

Hollow Block walling 100 mm

Supplying and filling in plinth with pulverised sand under floors including, watering, ramming consolidating and dressing complete.

Providing and fixing precoated galvalume (PPGL) steel profile sheets AZ-150 of brand Tata Bluescope steel everst industries Ltd., JSW steel Its. Jundal India Lts. Or equivalent (Size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50mm (+ 0.05 %) total coated thickness with aluminium zinc coating 150 grams per sqm as per IS:277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-Charge. The sheet shall be fixed using self drilling/self tapping luminium screws (Xylan) of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/vertical or curved surface, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and laying 75mm dia. PVC pipe for Weep Holes.

Supplying & laying stone boulder in sides of retaining wall as filter media.

Fabrication and supply of galvanized press steel water tank of size 7.50x7.50x2.50 having 1.40 lakhs litre capacity with checking and with all accessories such as nut i/c inlet, outlet over flow pipe connection lead with lead wise

Fabrication and supply of galvanized steel stagging of 12 mtrs. height for P.S water tank of capacity of 1.45 ltrs. tank including inside all round platform for ladder and walkway etc complete as per dircetion of EIC.

Providing, laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density

90-45mm size stone aggregate with 13.20mm stone screening

63-45mm stone aggregate with 13.20mm stone screening

53-22.4mm with stone aggregate with 11.20mm stone screening

Providing and fixing decorative cross bar above hand railing.

Supplying & laying stone aggregates in sides of filter chamber.

53mm to 40mm

20mm stone chips

IEI WORK (SHEDULE B)

SITC of 320 KW/400 KVA DG Set having DV8 TA Model, 490HP @ 1500 RPM Eight Cylinder Vertical, Water cooled Diesel oil Engine Directly Coupled with KOEL GREEN Make AC Alternator, 3 Phase, 415Vs, 50Hz @ 0.8 PF Self excited , self regulated designed run at 1500 RPM with Acoustic Enclosure (sound proof) as per Central Pollution conntrol Board (CPCB -II) approved DG Set as required.

Supplying of following XLPE insulated heavy duty armoured Copper conductor UG cable of 1.1 KV grade conforming to IS: No. 7098 (Part-I) and IS: No. 1554 (Part-I) 1958 as applicable. a) 630 Sqmm x 3.5 Core

Supplying, Installation, testing and commissioning of ASHLOK make SEE brand safe earthing electrode type-19, 50mm dia, length 2 mtrs and inner space to be filled with crystalline conductive mixture including filling up with electrodite (Back fill compound) as required for safe earth electrode and providing masonary enclosure with cover plate having locking arrangement etc. as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. a) 630 Sqmm x 3.5 Core

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. a) Above 400 sq. mm

SITC of 7.5 HP Kirloskar Make KDS 837++ Monoblock Electric Pump Set having 65mm x 65mm Suction and delivery, Head 12 to 24 m, discharge 27 to 15 ltrs/sec along with its Base frame and bolts and nuts including base frame grouting Bolt and nuts as required.

SITC of 2.0 HP Havells Make Model CS200 Monoblock Electric Pump Set having 75mm x 65mm Suction and delivery, Head 6M to 14 m, discharge 13 to 5 ltrs/sec along with its Base frame and bolts and nuts including base frame grouting Bolt and nuts as required.

SITC of 7.5 HP, three Phase DOL Starter for Electric motor including connection etc as required.

SITC of 2 HP, Signle Phase DOL Starter for Electric motor including connection etc as required.

Supplying and fixing of 4Way 63 A, 415V three phase Bus Bar Chamber including connection etc as required.

Supplying and fixing of 63A Cut Out (RYB) with Neutral Link 415V, 50Hz including connections etc as required.

Supplying and fixing of 4 Way SPN DB Double Door along with 1 No. 16A FP MCB including Connection etc as equired.

Supplying and fixing Bakelite batten/ angle holder including connection etc. as required.

Supplying of 0.5 Watt LED Lamp in the existing Batten Holder similar to C&S Cat No. LTHPLEDLAMP0.5WB22R/Y/B as required. ( 1 No each colour of Red, Yellow, Blue for phase indication)

Supplying of 12 Watt LED Lamp in the existing Batten Holder similar to C&S Cat No. LTHPLEDLAMP12WB22 as required.

Providing and fixing of Electrical Switch Board of size 1.20 mtr X 0.80 Mtr made up of 20 mm X 20mm X 5mm M.S equal angle on the outer Edge and 2 lengths of 20mm X 5mm M.S flat welded back for strengthening the structure horizontally and vertically over Width & height to form groove and fixing of 1.20 mtr x 0.80 mtr 12mm marine ply alongwith 2 Nos. 3mm thick phenolithic Board (Hylem sheet) of same size sandwitched one at the bottom and one on the top of ply suitably screwed with self threaded metal screw on the metal frame to form Regid Electrical Board as required.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. a) 6 x 4 sq. mm

b) 3 x 1.5 sq. mm

Supplying and drawing co-axial cable TV cable RG-6 grade, 0.7mm solid copper conductor PE insulated sheilded with fine tinned copper braid and protected with PVC sheatgh in the existing surface/ recessed steel/pvc conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. a) 25mm

Supply and fixing of 43" (108cm) LED TV Full HD with wall mounting bracket/ table top base and accessories for footage display as required. Model No. L43FN2, Make: LLOYD/AOC /LG/ Samsung/ Panasonic etc. or equivalent.

Supply, installation, testing & commissioning of 2MP Full HD IP Network Outdoor Bullet Camera Day/Night, 1/2.7" PS CMOS, 25/30 fps, 2.8/3.6 mm fixed Lens, IR Range of 30 mtr, IP67, POE, H.264+, H.264, DWDR, 3DNR, AWB, AGC, BLC. Make: CP PLUS, Model No. CP-UNC-TA20L3S-V2 or equivalent complete with all accessories, etc. as required.

Supply, installation, testing & commissioning of 2MP Full HD IP Network Vandal- resistant Dome Camera Day/Night, 1/2.8" PS CMOS, 25/30 fps, 2.8/3.6 mm fixed Lens, IR Range of 30 mtr, IP67, IK10, POE, H.264/ MJPEG, DWDR, 3DNR, ROI, AWB, AGC, BLC, HLC. Make: CP PLUS, Model No. CP-UNC-VA20L3S-VMS or equivalent complete with all accessories, etc. as required.

Supply, installation, testing & commissioning of 64 channel NVR capable of supporting 8 SATA HDDs upto 8TB each, 64-ch IP Network Cameras upto 12MP recording resolution, H.265/H.264/MJPEG compression, max 384Mbps incoming bandwidth, third- party IP cameras supported with ONVIF conformance & 2 HDMI/ 1 VGA simultaneous video output. Make: CP PLUS, Model No. CP-UNR-4K664R8-V2 or equivalent complete with all accessories, etc. as required.

Supply, installation, testing & commissioning of 4TB SATA HDD Surveillance Type Hard Disk. Make: WD/ Seagate or its equivalent.

Supply, installation, testing & commissioning of 8 Port PoE switch-10/100, RJ45 ports with power adapter for cameras. Model No. CP- TNW-HP8H1-12, Make: CP PLUS/DAHUA/ NETGEAR/ DLINK, etc. or equivalent complete with all accessories, etc. as required.

Supply, installation, testing & commissioning of 16 Port Gigabit Unmanaged PoE switch-10/100/1000, RJ45 ports with power adapter for cameras. Model No. GS116LP, Make: NETGEAR/CP PLUS/DAHUA/DLINK, etc. or equivalent complete with all accessories, etc. as required.

Supply and fixing of IP65 Weather Proof Camera Box complete with all accessories, etc. as required.

Supply of Cordless mouse USB type for NVR. Model No. Zeb- Dazzle, Make: Zebronics/Dell/HP or equivalent.

Supply and drawing of HDMI cable in the existing surface/ recessed Steel/ PVC conduit as required.

Supply and fixing of Wall mount Network Rack- Standard 19" rack x 6U for mounting NVR accessories including connections, etc. as required.

Supply and fixing of Wall mount Network Rack- Standard 19" rack x 2U for mounting NVR accessories including connections, etc. as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable with RJ45 connectors in the existing surface/ recessed Steel/ PVC conduit as required.

a) 1 run of cable

Supplying and fixing of LED Decorative Post of Lantern Fitting 30 Watt Similar to C&S CETUS-M-Series Cat No.LTGLM30WHPLED/W with suitable G.I. Pipe support with collar for fixing the fitting on the Gate piller as required.

Supplying and fixing of LED Street Light Fitting 70 Watt Similar to C&S Indus -i Cat No.LTESSI70WLED on existing G.I. Pipe Street Light Pole as required.

Supply of factory made 5 mtr. high hot dip galvanized octagonal pole having 130mm dia at the bottom and 70mm dia at the top made up of 3mm thick HR sheet along with base plate of size 200mm x 200mm x 12mm thick including supply of 1 mtr. long hot dip galvanized standard double arm bracket made up of 40NB G.I. pipe suitable to mount on pole top and foundation "J" bolts of length 600mm (as per the enclosed specificaiton of pole & accessories) similar to Bajaj pole type Cat No. BOP-5030 or its equivalent in other reputed manufacturers complete to as required.

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.

Supplying of the following sizes of PVC insulated PVC sheathed (Heavy duty) armoured power cable with Al. Conductor for working voltage upto including 1.1 KV grade conforming to IS:1554 (Part-I) as applicable.

a) 16 sq.mm x 4 core

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

a) Upto 35 sq. mm

Supplying and Laying of One Number Double Walled Corrugated High Density Polyethylene Pipe having Corrugation on the outer wall and plain surface inner wall confirming to IS 14930 Part-I Complete with necessary HDPE fitting for protection of 1.1 KV Grade underground cable directly in ground at the depth of 50 cm in the existing Cable Trench etc., as required.

a) 50/38 mm outer dia

Supplying and Laying of One Number Double Walled Corrugated High Density Polyethylene Pipe having Corrugation on the outer wall and plain surface inner wall confirming to IS 14930 Part-I Complete with necessary HDPE fitting for protection of 1.1 KV Grade underground cable directly on the Surface or Wall or in existing trench etc., as required.

a) 50/38 mm outer dia

Supplying and fixing of ready made 3 phase Digital 24 Hrs street light timer panel having max load delvering capcity of 6 Kw similar to Havells Cat No. IHXTS03060 on the existing street light circuit as required.

Supplying, installation, testing and Commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required: (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.

Supplying, installation, testing and ommissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, entrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required.

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 56m Head

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories,

mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required:

accessories for automatic operation of diesel engine System Controller Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specification.

Pipe & Accessories

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. a) 150 mm. dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : a) 200 mm. dia (wall thickness = 6.3 mm)

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required.

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required.

a) Single headed Stainless steel

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required.

a) Single headed Stainless steel

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required.

a) 80mm dia

b) 100 mm dia

c) 150 mm dia

d) 200 mm dia

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required.

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required.

a) 80mm dia

b) 150mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

a) 80mm dia

b) 150mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required.

a) Gun metal

Provioding and fixing of M.S. Fire Hose Cabinet of 750 mm x600mm x 250mm made out of 16 Gauge M.S. Sheet Capable of accommodating fire hose reel, landing valve , Hose pipes, fittings and accessories. The door shall have front glass with lock and key arrangement and shall be painted with posrt office RED colour make: Life Guard or its equivalant as required.

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585. 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required.

a) 4 way - 150 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories.

a) Pendent Sprinkler

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.

a) 100mm dia

Fire Extinquishers

Supply & fixing of fire extinguisher, DCP/ABC Type 6.00 kg capacity (ISI Marked conforming to IS:15683) squeeze grip type with discharge hose & nozzle complete with initial charge and wall bracket, suitable size mounting screws, etc. as required.

Supply & fixing of CO2 type fire extinguisher, 4.50 kg capacity (ISI Marked conforming to IS:15683) squeeze/ wheel grip type with discharge hose & horn complete with initial charge and wall bracket, suitable size mounting screws, etc. as required.

Supply & fixing of Water CO2 type fire extinguisher, 9.00 Ltr capacity (ISI Marked conforming to IS:15683) squeeze grip type with discharge hose & nozzle complete with initial charge and wall bracket, suitable size mounting screws, etc. as required.

Supply & fixing of AFFF/ Mechanical Foam type fire extinguisher, 9.00 Ltr capacity (ISI Marked conforming to IS:15683) squeeze grip type with discharge hose & nozzle complete with initial charge and wall bracket, suitable size mounting screws, etc. as required.

FIRE DETECTION & ALARM SYSTEM

Supplying, installation, testing and commissioning of UL listed Analogue Addressable Fire Alarm Control Panel, with the following loop modules and capable of supporting not less than 240 devices (including detectors) per loop, network communication card, LCD display with inbuilt reset, test, acknowledge, silence switches and annunciation to indicate fire and fault conditions, LED lamps for visual indication, audio alarm unit and minimum 2000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5 % V, 50 hz), including back-up of 24 volt sealed maintenance free batteries( 12Ah, 12V battery x 2 nos.) with automatic charger and suitable End of line resistors complete with necessary programming & suitable power supply cable and plugtop, mounted on the wall surface . The panel shall be compatible for RS 485 Communication facility for Network / Repeater/ MODBUS / BACnet. Make: Ravel Avani or its equivalent. a) Four Loop Panel

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying, installation, testing & commissioning of Analogue Addressable Photoelectric Smoke Detector with LED and mounting base complete with all connections etc. as required, on wall/ ceiling/ false ceiling. Make: Ravel RE 317D - SL or its equivalent.

Supplying, installation, testing & commissioning of Analogue Addressable Heat Detector with rate of rise cum fixed tempreature thermistor with LED and mounting base complete with all connections etc. as required, on wall/ ceiling/ false ceiling. Make: Ravel RE 317D - HL or its equivalent.

Supplying, installation, testing & commissioning of Analogue Addressable Isolator Module complete with mounting back boxes, all connections etc. as required, on wall/ ceiling/ false ceiling. Make: Ravel RE -717MI or its equivalent.

Supplying, installation, testing & commissioning of Analogue Addressable Manual Call Point complete with all connections etc. as required, on wall/ ceiling/ false ceiling. Make: Ravel RE-717M or its equivalent.

Supplying, installation, testing & commisssioning of Sounder cum Strobe 24VDC operated complete with mounting back boxes, all connections, etc. as required on wall/ ceiling/ false ceiling. Make: Ravel RE-716SS or its equivalent.

Supplying, installation, testing & commissioning of Analogue Addressable Control Module complete with mounting back boxes, connector strip, all connections, End of Line Resistors, etc. as required on wall/ ceiling/ false ceiling. Make: Ravel RE-717MC or its equivalent.

Supplying, installation, testing & commissioning of Analogue Addressable Monitor Module complete with mounting back boxes, connector strip, all connections, End of Line Resistors, etc. as required on wall/ ceiling/ false ceiling. Make: Ravel RE-717MC or its equivalent.

Supply and Fixing of Industrial Electric Siren- 1.0 Km sound range, 230VAC operated complete with suitable power supply cable and plugtop, mounted on the wall/ base with suitable mounting accessories, etc. as required and as directed at site.

Supplying and fixing of wall mouting type corrosive resistive body LED based Double high glow & Exit Sign emergency Fire Exit light with 12V, 7AH battery backup upto 4 Hrs having Mains on fuse blown Indication and protection over deep discharge & over Charge of battery as required.

PUBLIC ADDRESS SYSTEM

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. a) 20mm

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. a) speaker cable Single pair, 2-core, 1.5 sqmm

Providing, installation, testing and commissioning of 1.0 Ton 5 Star split type Digital Inverter Air conditioner of stabilizer free operation , single rotary compressor having 10 years warranty, 1 Phase 230 volt, (Condenser coil must be of copper material), suitable for wall mounting i/c drilling holes on the wall for passing gas pipes, fixing PVC pipe on the wall through the holes and cementing, painting to give an even look and smooth finish, wrapping PVC non adhesive white tape over insulation of gas pipes etc i/c extra refrigerant pipes wherever necessary as required and as per the direction of E-in-C. Make: LLOLYD , Model No.GLS12I56WBEL or equivalent in Bluestar/Hitachi/ Videocon/ Voltas/ Vestar etc.

Providing, installation, testing and commissioning of 1.5 Ton 5 Star split type Digital Inverter Air conditioner of stabilizer free operation , single rotary compressor having 10 years warranty, 1 Phase 230 volt, (Condenser coil must be of copper material), suitable for wall mounting i/c drilling holes on the wall for passing gas pipes, fixing PVC pipe on the wall through the holes and cementing, painting to give an even look and smooth finish, wrapping PVC non adhesive white tape over insulation of gas pipes etc i/c extra refrigerant pipes wherever necessary as required and as per the direction of E-in-C. Make: LLOLYD , Model No.GLS18I56WBEL or equivalent in Bluestar/Hitachi/ Videocon/ Voltas/ Vestar etc.

Providing, installation, testing and commissioning of 2.0 Ton 5 Star split type Digital Inverter Air conditioner of stabilizer free operation , single rotary compressor having 10 years warranty, 1 Phase 230 volt, (Condenser coil must be of copper material), suitable for wall mounting i/c drilling holes on the wall for passing gas pipes, fixing PVC pipe on the wall through the holes and cementing, painting to give an even look and smooth finish, wrapping PVC non adhesive white tape over insulation of gas pipes etc as required and as per the direction of E-in-C. Make: LLOLYD , Model No.GLS24I56WBEL or equivalent in Bluestar/Hitachi/ Videocon/ Voltas/ Vestar etc.

Supplying and fixing of 4KVA Voltage stabilizer for 1.0/1.5 Ton Air Conditioner Make: V-Guard, Model: VG 400 or equivalent etc. as required.

Supplying and fixing of 5KVA Voltage stabilizer for 2.0 Ton Air Conditioner Make: V-Guard, Model: VGN 500 or equivalent etc. as required.

Providing & fixing of pre-fabricated stand for keeping outdoor units of split type Air Conditioners of capacity 1/1.5/2 Ton etc. as required.

Supplying and fixing of 120 litrs storage type Normal & cold water dispenser with inbuilt uv filteration facilities similar to Bluestar model SWCNST80120UVE or its equivalent as required.

O P KANDOI AND COMPANY PVT LTD

Surendra Infrastructure Pvt. Ltd.

PRASHANTH ERECTOR & BUILDERS PVT LTD