JH-XVI-II-RAN-02

Amount

Details

L081 TO KHIRDA - 3.660KM

Setting out etc all complete job as per specification and directioni of E/I

Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical specification Clause 201.

Excavation in Cutting in Soil by manual means with lead upto 50 m Excavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per Technical Specification Clause 302.3

Compacting original ground supporting subgrade: Loosening, of the ground upto level of 300 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of of Tables 300.1 and 300.2 for subgrade construction as per Technical Spe

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 250m as per Technical Specification Clause 301.5

Qty (Free Lead)

(Lead upto 250m))

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per Technical Specification Clause 303.1.

Waterproofing on top of the sub Grade soil base with Nano technology based "Terrasil" Organo silane nanotechnology & "Zycobond" nano acrylic co-polymer with water (<1000 ppm TDS) in the ratio of 1:1:200 @ 3 ltrs/sqm as per direction of the Engineer-in-charge. (IRC accreditation of Terrasil is : IRC-24(7)/2017 (ACC-224) and Zycobond is : IRC-24(7)/2017 (ACC-225))

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. GRADING-III

Stabilized Sub-base / Base with Nano-technology: Providing, Laying, Spreading and Compacting 70% GSB-III mixed with 30% GSB Grade-II as per mix design. Application: (1) Rip and loosen GSB material with excavator / tractor operated ripper and scarify with tractor operated rotavator to achieve desired thickness of 300 mm. Mix aggregates as per mix design with rotavator. (2) Spread Cement 3% by weight of soil aggregate mix and mix with tractor operated rotavator. (3) Prepare and apply 0.75 kg /cum organosilane Nanotechnology and 0.75 kg/cum acrylic copolymer mixed in OMC water (<1000 ppm TDS) on loose mix . Scarify the treated mix with rotavator. (4) Compact partially the surface with vibratory roller. (5) Spread 13.2 and down size aggregates on the graded soil surface to form 20-25 mm thick aggregate-cement layer. (6).Compact the stabilized aggregate-cement base with 8 to 10 tonne vibratory roller to achieve stone embedded layer with the desired density and thickness. (7) Waterproof the top of the compacted stabilized base with organosilane & nano acrylic Polymer in the ratio of 1 kg organosilane :1 kg nano acrylic Co-Polymer : 200 liter water (<1000 ppm TDS) @ 3ltrs/sqm in two spray applications (1.5 ltrs. + 1.5 ltrs.). Rates include all material, labour, hire charges of machinery etc. as per MoRD specifications & direction of Engineer-in-Charge. IRC accreditation of Terrasil is : IRC-24(7)/2017 (ACC-224) and Zycobond is : IRC-24(7)/2017 (ACC-225)

Prime Coat : Preparing and applying of water soluble Terraprime organo silane nanotechnology (for bitumen emulsion application, IRC approved) with cationic bitumen emulsion CSS1 and water (<1000 ppm TDS) in the ratio of 1 kg silane : 100 kg cationic bitumen emulsion : 200 liter water . Take 1 kg of silane nanotechnology and add in 200 liter water while filling water in tanker/drum and then add 100 kg cationic bitumen emulsion under circulation. Mix the solution completely. Spray the solution at the rate of 1 liter per sqm on compacted stone base. Check quality of bitumen emulsion before bulk use. Terraprime IRC accreditation : IRC-24(7)/2017 (ACC-234)

Open Graded Premix Carpet with Nano-Technology :-Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion Mixed with Nano Technology Based Organo Silane Compound @ 0.1% by the weight of bitumen for enhansed performance and durability to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. ZycoTherm IRC accreditation: IRC-24(7) / 2017 (ACC-248)

Seal Coat with Nano-Technology -Providing and laying seal coat with ZycoTherm organo silane nanotechnology @ 0.1% by the weight of bitumen, sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B as per Technical Specification Clause 510 ZycoTherm IRC accreditation : IRC-24(7) / 2017 (ACC-248)

Construction of un-reinforced, dowel jointed at expansion and construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days

Providing and fixing of typical PMGSY informatory Sign Board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick top and middle plate duly welded with MS flat iron 25mmx5m size on back onedges. The lower plate will be welded with MS angle iron frame of 25mmx25mm x5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75mm x 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All MS will be stoe enameled on both sides. Lettering and printng arrows, border etc will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy as per drawing.

Direction and Place Identification Signs upto 0.9 sqm Size Board. Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing

Providing and fixing of retro- reflectorised cautionary, mandatory and Traffic Sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminum sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing

Reinforced cement concrete M-15 grade Ordinary Kilometer Stone (Precast) stone/Local stone of stadard design as per IRC:8 fixing in position including painting and printing etc as per drawing and Technical Specification Clause 1703.

Reinforced cement concrete M-15 grade 200m stone (Precast) stone/Local stone of stadard design as per IRC:8 fixing in position including painting and printing etc as per drawing and Technical Specification Clause 1703.

Boundary pillar: Reinforced cement concrete M-15 grade boundary pillars/Local stone of standard design as per IRC:25 fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 704. (Boundary pillar/ FI Post)

Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered/concrete surface as per drawing and Technical Specification Clause 1701

Protection Work

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.

Providing and laying boulder pitching on slope over prepared filter media in embankment protection with stone boulders of minimum size 25kg laid by dry complete as per drawing and technical specification Clause 1301

Plain Cement Concrete M10 (1:3:6 nominal mix) in levelling Coarse below open foundation of Head walls as per drawings & Technical Specification Clause 1109

Stone masonry in cement mortar (1:4) random rubble masonry for foundation complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Stone masonry in cement mortar (1:4) random rubble masonry for superstructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Providing weep holes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Plastering with cement mortar (1:4), 25mm thick on brick work in substructure as per technical specification.

Providing 1.5 mm thick cement punning -do -do- etc. all complete job as per specification and direction of E/I.

Back filling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8

Providing coarse clean sand filling in foundation trenches including ramming and watering in layer not exceeding 100mm thick with all leads and lifts including cost of sand, labour, royalty and taxes all complete job as per specification and direction of E/I.

Providing and laying boulder pitching on slope over prepared filter media in embankment protection with stone boulders of minimum size 25kg laid by dry complete as per drawing and technical specification Clause 1301

HUME PIPE CULVERT 1nx1m dia

Excavation for Structures Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 including setting out,construction of shorting and bracing, removal of stumps and other deleterious

Bedding for pipe (ii) Type A (First Class) Bedding on well compacted sand, moorum or approved granular material as per clauses 1105 (ii)

Plain Cement Concrete M10 (1:3:6 nominal mix) in levelling Coarse below open foundation of Head walls as per drawings & Technical Specification Clause 1109

Stone masonry in cement mortar (1:4) random rubble masonry for foundation complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Providing and laying 1000mm dia reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar (1:2) but excluding excavation, protection works, backfilling, concrete and masonry work in head walls and parapets clause 1106 SOR 9.3 (B)

Plastering with cement mortar (1:4), 25mm thick on brick work in substructure as per technical specification.

Providing white washing, three coats over new surface with approved quality of lime including cost of cleaning surface thoroughly and removing the scales of smoke and mash marks with jhama rubbing scaffolding, washing of floors and taxes all complete as per building specification and direction of E/I.

Providing Stone masonary in CM (1:4) in parapet - do- -do- etc. all complete job.

Plastering with cement mortar (1:4), 25 mm thick on stonework in substructure as per technical specification Clauses 613.4 & 1204

Maintenance

For 1st Year

For 2nd Year

For 3rd Year

For 4th Year

For 5th Year

(2)- L091-L047 TO UTTAR TOLI Length-0.820 k.m.

Setting out etc all complete job as per specification and direction of E/I

Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical specification Clause 201.

Compacting original ground supporting subgrade: Loosening, of the ground upto level of 300 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of of Tables 300.1 and 300.2 for subgrade construction as per Technical Spe

Excavation in Cutting in Soil by manual means with lead upto 50 m Excavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per Technical Specification Clause 302.3

Construction of embankment with approved material obtained from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5

Qty (Free Lead)

(Lead upto 250m))

Sub grade: Providing, laying and spreading soil on a prepared sub-grade, pulverising, adding the designed quantity of cement to the spread soil, mixing in place with rotavator, grading with the motor grader and compacting with the road roller at OMC to achieve the desired unconfined compressive strength and to form a layer of sub-base/base as per Technical Specification Clause 404.

Construction of subgrade and earthen shoulders with approved materials obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 250m as per Technical Specification 301.4.1

75% of total Quantity

25% of total Quantity

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. GRADING-III CEMENT TREATED @5%

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. GRADING-II CEMENT TREATED @5%

PRIME COAT (i) Low porosity Providing and applying primer coat with Bitumen 80/100 on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.7-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502.

Surface dressing using Bituminous Emulsion ( Nominal chipping size 13.2 mm) Providing and laying surface dressing as wearing course consisting of a layer of bitumen emulsion laid on the prepared surface, followed by a cover of crushed stone chippings of specified size and rolling with 80-100 kN roller including cleaning the road surface as per Technical Specification Clause 507.

Surface dressing using Bituminous Emulsion ( Nominal chipping size 9.5 mm) Providing and laying surface dressing as wearing course consisting of a layer of bitumen emulsion laid on the prepared surface, followed by a cover of crushed stone chippings of specified size and rolling with 80-100 kN roller including cleaning the road surface as per Technical Specification Clause 507.

Providing and fixing of typical PMGSY informatory Sign Board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick top and middle plate duly welded with MS flat iron 25mmx5m size on back onedges. The lower plate will be welded with MS angle iron frame of 25mmx25mm x5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75mm x 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All MS will be stoe enameled on both sides. Lettering and printng arrows, border etc will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy as per drawing.

Direction and Place Identification Signs upto 0.9 sqm Size Board. Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing

Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing

Reinforced cement concrete M-15 grade Ordinary Kilometer Stone (Precast) stone/Local stone of stadard design as per IRC:8 fixing in position including painting and printing etc as per drawing and Technical Specification Clause 1703.

Reinforced cement concrete M-15 grade 200m stone (Precast) stone/Local stone of stadard design as per IRC:8 fixing in position including painting and printing etc as per drawing and Technical Specification Clause 1703.

Boundary pillar: Reinforced cement concrete M-15 grade boundary pillars/Local stone of standard design as per IRC:25 fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 704. (Boundary pillar/ FI Post)

Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered/concrete surface as per drawing and Technical Specification Clause 1701

HUME PIPE CULVERT 1nx1m dia

Excavation for Structures Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 including setting out,construction of shorting and bracing, removal of stumps and other deleterious

Bedding for pipe (ii) Type A (First Class) Bedding on well compacted sand, moorum or approved granular material as per clauses 1105 (ii)

Plain Cement Concrete M10 (1:3:6 nominal mix) in levelling Coarse below open foundation of Head walls as per drawings & Technical Specification Clause 1109

Stone masonry in cement mortar (1:4) random rubble masonry for foundation complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Providing and laying 1000mm dia reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar (1:2) but excluding excavation, protection works, backfilling, concrete and masonry work in head walls and parapets clause 1106 SOR 9.3 (B)

Plastering with cement mortar (1:4), 25mm thick on brick work in substructure as per technical specification.

Providing white washing, three coats over new surface with approved quality of lime including cost of cleaning surface thoroughly and removing the scales of smoke and mash marks with jhama rubbing scaffolding, washing of floors and taxes all complete as per building specification and direction of E/I.

RCC Culvert 1nx3mx2m

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.

Providing and laying boulder pitching on slope over prepared filter media in embankment protection with stone boulders of minimum size 25kg laid by dry complete as per drawing and technical specification Clause 1301

Plain Cement Concrete M10 (1:3:6 nominal mix) in levelling Coarse below open foundation of Head walls as per drawings & Technical Specification Clause 1109

Random Rubble Stone masonary work in cement mortar (1:4) in foundation complete as per drawing and technical specification clause 802, 803, 1202 and 1203

Random Rubble Stone masonary work in cement mortar (1:4) in super structure complete as per drawing and technical specification clause 802, 803, 1202 and 1203

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Providing RCC (1:1½:3) in deck slab with approved quality of stone chips and clean coarse sand as per spec ification and direction of E/I.

Providing RCC (1:1½:3) in Wearing coat with approved quality of stone chips and clean coarse sand as per spec ification and direction of E/I. Wearing coat

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Providing shuttering including strutting in slab as per specification and direction of E/I.

Providing weep holes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Providing MS Tor steel reinforcement (10-12 mm dia Rod) as per approved design and drawing including cutting, bending, and binding and placing in position as per specification and direction of E/I. Bed plate vide item no. 6

Providing 25mm thick cement plaster (1:4) with clean coarse sand of FM 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I

Providing and fixing 25mm thick expansion join in culverts filling the same with bitumen cement and sand etc. including the cost of all labour and materials all complete job as per specificition and directio of engineer incharge

Earthwork in back filling in foundation all complete job as per specification and direction of E/I.

Maintenance

For 1st Year

For 2nd Year

For 3rd Year

For 4th Year

For 5th Year

(3)-TANGARIA TO HARIJANTOLI, , Length-2.320 KM

Setting out etc all complete job as per specification and direction of E/I

Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical specification Clause 201.

Removing all types of Hume pipes and stacking within a lead of 1000 m including Earthwork and Dismantling of Masonry Works as per Technical Specification Clause 202.

Compacting original ground supporting subgrade: Loosening, of the ground upto level of 300 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of of Tables 300.1 and 300.2 for subgrade construction as per Technical Spe

Excavation in Cutting in Soil by manual means with lead upto 50 m Excavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per Technical Specification Clause 302.3

Construction of embankment with approved material obtained from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5

Qty (Free Lead)

(Lead upto 250m))

Sub grade: Providing, laying and spreading soil on a prepared sub-grade, pulverising, adding the designed quantity of cement to the spread soil, mixing in place with rotavator, grading with the motor grader and compacting with the road roller at OMC to achieve the desired unconfined compressive strength and to form a layer of sub-base/base as per Technical Specification Clause 404.

Construction of subgrade and earthen shoulders with approved materials obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 250m as per Technical Specification 301.4.1

75% of total Quantity

25% of total Quantity

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. GRADING-III CEMENT TREATED @5%

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. GRADING-II CEMENT TREATED @5%

PRIME COAT (i) Low porosity Providing and applying primer coat with Bitumen 80/100 on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.7-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502.

Surface dressing using Bituminous Emulsion ( Nominal chipping size 13.2 mm) Providing and laying surface dressing as wearing course consisting of a layer of bitumen emulsion laid on the prepared surface, followed by a cover of crushed stone chippings of specified size and rolling with 80-100 kN roller including cleaning the road surface as per Technical Specification Clause 507.

Surface dressing using Bituminous Emulsion ( Nominal chipping size 9.5 mm) Providing and laying surface dressing as wearing course consisting of a layer of bitumen emulsion laid on the prepared surface, followed by a cover of crushed stone chippings of specified size and rolling with 80-100 kN roller including cleaning the road surface as per Technical Specification Clause 507.

Providing and fixing of typical PMGSY informatory Sign Board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick top and middle plate duly welded with MS flat iron 25mmx5m size on back onedges. The lower plate will be welded with MS angle iron frame of 25mmx25mm x5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75mm x 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All MS will be stoe enameled on both sides. Lettering and printng arrows, border etc will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy as per drawing.

Direction and Place Identification Signs upto 0.9 sqm Size Board. Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing

Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing

Reinforced cement concrete M-15 grade Ordinary Kilometer Stone (Precast) stone/Local stone of stadard design as per IRC:8 fixing in position including painting and printing etc as per drawing and Technical Specification Clause 1703.

Reinforced cement concrete M-15 grade 200m stone (Precast) stone/Local stone of stadard design as per IRC:8 fixing in position including painting and printing etc as per drawing and Technical Specification Clause 1703.

Boundary pillar: Reinforced cement concrete M-15 grade boundary pillars/Local stone of standard design as per IRC:25 fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 704. (Boundary pillar/ FI Post)

Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered/concrete surface as per drawing and Technical Specification Clause 1701

Protection Work

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.

Providing and laying boulder pitching on slope over prepared filter media in embankment protection with stone boulders of minimum size 25kg laid by dry complete as per drawing and technical specification Clause 1301

Plain Cement Concrete M10 (1:3:6 nominal mix) in levelling Coarse below open foundation of Head walls as per drawings & Technical Specification Clause 1109

Stone masonry in cement mortar (1:4) random rubble masonry for foundation complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Stone masonry in cement mortar (1:4) random rubble masonry for superstructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Providing weep holes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Plastering with cement mortar (1:4), 25mm thick on brick work in substructure as per technical specification.

Providing 1.5 mm thick cement punning -do -do- etc. all complete job as per specification and direction of E/I.

Back filling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8

Providing coarse clean sand filling in foundation trenches including ramming and watering in layer not exceeding 100mm thick with all leads and lifts including cost of sand, labour, royalty and taxes all complete job as per specification and direction of E/I.

Providing and laying boulder pitching on slope over prepared filter media in embankment protection with stone boulders of minimum size 25kg laid by dry complete as per drawing and technical specification Clause 1301

HUME PIPE CULVERT 1nx1m dia

Excavation for Structures Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 including setting out,construction of shorting and bracing, removal of stumps and other deleterious

Bedding for pipe (ii) Type A (First Class) Bedding on well compacted sand, moorum or approved granular material as per clauses 1105 (ii)

Plain Cement Concrete M10 (1:3:6 nominal mix) in levelling Coarse below open foundation of Head walls as per drawings & Technical Specification Clause 1109

Stone masonry in cement mortar (1:4) random rubble masonry for foundation complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Providing and laying 1000mm dia reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar (1:2) but excluding excavation, protection works, backfilling, concrete and masonry work in head walls and parapets clause 1106 SOR 9.3 (B)

Plastering with cement mortar (1:4), 25mm thick on brick work in substructure as per technical specification.

Providing white washing, three coats over new surface with approved quality of lime including cost of cleaning surface thoroughly and removing the scales of smoke and mash marks with jhama rubbing scaffolding, washing of floors and taxes all complete as per building specification and direction of E/I.

PARAPET REPAIR

Providingstone masonary in cm (1:4) in parapet-do-do-etc.all complete job.

Plastering with cement mortar (1:4), 25mm thick on stone work in substructure as per technical specification. Clauses 613.4 &1204

Maintenance

For 1st Year

For 2nd Year

For 3rd Year

For 4th Year

For 5th Year

ANKIT KUMAR SHUKLA