Special Repair for Replacement of Roof of Administrative Block in Govt ITI at Kaithal

Amount

Dismantling of brick work & tile terracing etc. in cement (HSR8.5 (b)).

Dismatnling Roofing (h) Removing of RCC Battens from roof (HSR 8.8(h)).

Dismantling steel work upto a height of 5 metres in built up section in angles, tees, flats and channels including all gusset plates, bolts, nuts, beading etc. (b) excluding smembering (HSR 8.22 (b)).

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work for walls exceeding 20cm thickness (straight and curved) beams, girders, stairs, columns, (square or rectangular) battens and lintels etc. excluding steel reinforcement but including centring and shuttering, laid in position, complete in all respects.. (HSR 10.86 + 10.95 a)).

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position complete in all respects. (HSR 10.82+10.95 (a)).

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coasts of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13).

11.43 cm thick brick wall laid in cement sand mortar 1:4 in superstructure (HSR 11.48 a)).

Dismantling cement conglemerate / terrazzo floors 25 mm to 50 mm thick including concrete base (HSR 8.25).

Cement Concrete 1:8:16 with stone aggregate 40mm nominal size in foundation and plinth (HSR 10.28).

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSONS, RAK & SIMPOLO (HSR 14.89).

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in skirting / dado laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSONS (HSR 14.90).

Steel reinforcement TMT bars FE-500 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bendings, wastage, overlaps, welded joints, spacer bars chairs stays hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths/ storeys/basements etc.(Note: reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. Couplings, welded joints, specers bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. Binding, wastage, overlaps, welded joints, spacer bars chairs stays hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths/ storeys/basements etc.(HSR 18.22)

First class brickwork laid in cement sand mortar 1:6 in first storey upto 4 meters above plinth level. (HSR 11.7)

Removing doors and windows (wooden and steel) together with the dismantling of walls (HSR 8.17). (A) Doors

(B) Windows

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, lock notch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete: - (a) Doors and windows frams of size (89 x 50 mm with 40 mm wide single. (HSR 18.34 (a))

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659- 1969 bonded with water proof type phenol formaldehyde synthetic esin,hotpressesd, conforming to I.S.2202 part I and II, fixed in position,including iron hinges,screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above,but including labour for fixing the same in position)- (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges.) (iii) 35 mm thick. (HSR 17.93 (a) (iii)) - Note

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS;733 and IS;1285 fixed with rawlplugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom, and sides with required neoprene felt etc.aluminium sections shall be smooth, rust free straight mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/panelling C.P brass /stainless steel screws, etc. complete. Shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PBC/ neoprene gasket required including aluminium fitting i.e. aluminium kun (HSR 17.96). +Note-II

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS; 12823 grage 1 type II in panelling fixed in aluminium doors. Windows shutters and partition frames with c.p. brass /stainless steel screws etc. complete. (b) Pre-laminated particle board with decorative lamination on both sides (HSR 17.97 (b))

Providing and fixing glazing in aluminium door, windows ,ventilator shutter and partitions etc. with pvc/neoprene gasket etc. complete (cost of aluminium snap beading shall be paid in basic items). (b) with float glass 5 mm thick (HSR 17.98 (b))

Providing & Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (Note:- Reputed make PVC Pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. [HSR 13.89].Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. (b) 150mm dia PVC Bend

Providing and fixing PVC Bend ISI Mark. (Note:- Reputed make PVC Bend such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge.[HSR13.90].Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.(b) 150mm dia PVC Bend

Providing fixing aluminium caement windows fasterner of reuqired length for aluminium windows with ne3cessary screws etc. complete. ii) Powder coated minium thickness 50mm HSR 17.101 (ii)

Providing fixing aluminium round shape handle of outer dia 100mm with Ssscrews etc. complete.II) powder coated minimum thickness 50 micron aluminium (HSR 17.103(ii)

12 mm thick cement plaster 1:4 (HSR 15.5).

15 mm thick cement plaster 1:4 on the rough side of single or half brick wall (HSR 15.10).

10 mm Cement Plaster 1:4 under side of ceiling (HSR 15.52)

Providing & laying average 6mm thick POP Coating on walls, Ceiling, beams and lintels etc. complete in all respects as approved by the Engineer-In-Charge. (HSR 13.94)

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised @ 80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be prepainted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. (with or without grooves). (13.92).

Providing and Applying two coats white cement based putty over plastered surface and grinding the surface smoothwith sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. NOTE:- Reputed make putty such as J.K./Birla shall be used as approved by Engineer-in-Chief. (J.K. / Birla make). (HSR 16.81).

Scraping of white wash or colour wash (HSR 8.32 (a).

Providing and aApplying Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (NOTE:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garwarte, Jenson, Nicholson, Asian & Shalimar shall be used as approved by Engineer-in-Charge in writing, Drum of paint shalll be opened in presence of Engineer-in-Charge). (HSR 16.58)

Providing and Applying providing two coats of exterior acrylic emulsion paint. (NOTE:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garwarte, Jenson, Nicholson, Asian & Shalimar shall be used as approved by Engineer-in-Charge in writing, Drum of paint shalll be opened in presence of Engineer-in-Charge) (HSR 16.79 (a)).

Providing and Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (NOTE:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garwarte, Jenson, Nicholson, Asian & Shalimar shall be used as approved by Engineer-in-Charge in writing, Drum of paint shalll be opened in presence of Engineer-in-Charge) (HSR 16.2).

Providing and applying painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an enen shad. (NOTE:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garwarte, Jenson, Nicholson, Asian & Shalimar shall be used as approved by Engineer-in-Charge in writing, Drum of paint shalll be opened in presence of Engineer-in-Charge) (HSR 16.3).

Factory manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash,etc.,(non-coniferous timber other teak,conforming to I.S.specification No.1003, kiln-seasoned),with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail, and wire gauze of 140G or 120G designation including cost of iron hinges, screws,chocks/cleats,stops nail etc.,complete fixed in position (excluding the cost of any fitings,other than specified above,but including labour for fixing the same in position)- (style and rails of windows shutter shall be 75 mm wide) (HSR 17.92) (i) 30 mm thick

Supplying and fixing hydraulic door closer, I.S.I.mark, with necessary screws, etc., complete. (c) I.S.I. designation No.III (size of door 851 mm to 1000 mm ) (HSR 17.82) (c))

Providing and fixing HDPE water storage tanks of Sintex, Diplast, O.K. make with covers/lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in- Charge. (except civil work). (e) 1000 ltr. capacity (HSR 30.119 (e))

PROVIDING AND FIXING POSITION BEST INDIAN MAKE FLAT BACK OR ANGULAR LIPPED FRONT URINAL 465 MM HIGH CONSISTING OF : -(i) Flat back lipped or angular urinal basin of VITREOUS CHINA WARE (to the approval of the Engineer-in-charge). (ii) 5 LITRES CAPACITY mosquito proof INDIAN MAKE C.I.AUTOMATIC FLUSHING CISTERN, PAINTED WITH non-yellowing white enamel paint or other approved shade enamel paint on outside and superior black bitumastic paint on inside complete with screwed 15 mm pipe; (iii) PAIR OF R.S.PR C,I. PAINTED BRACKETS AND BRASS COUPLINGS; (iv) Standard size G.I.FLUSH PIPE WITH C.P.BRASS WALL CLIPS AND UNIONS COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOOR AND PAINTING OF FITTINGS ETC. (as required by the Engineer-in-charge). (i) White (HSR 30.19 (i))

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT WITH NONCONCEALED ‘P’ OR ‘S’ TRAP with or without vent and all other necessary fittings as fully described in item no.30.3 above (HSR 30.4 (i))

Providing and fixing in position quality stainless steel sink built in draining board of size 600mm X 450 mm complete as described in item no.30.53 and 30.58 above (a) Sink size 600 X 450 X 200 mm (HSR 30.52 (a))

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (ORDINARY) LAVATORY SUITES consisting of Lavatory in VITREOUS CHINAWARE size as give below ( to the approval of he Engineerin- charge) including china plug for tap hole where necessary ; R.S. or C.I.BRACKETS for building into wall including painting; 32mm C.P.BRASS WASTE WITH C.P. rass chain and rubber plug; 15mm C.P.BRASS SCREW DOWN PILLAR TAP WITH jam nuts or couplings best design (as approved by the Engineer-in-charge) ALL FITTINGS BEST INDIAN MAKE and; to the approval of the Engineer-in-charge. ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and MAKING GOOD THE WALLS, FLOORS AND PAINTING OF FITTINGS ETC. (iv) Size 630mm X 450 mm with one no. tap (HSR 30.41 (iv))

Pdg. & Fixing G.I.Pipe complete with GI fitting and clamps, i/c cutting & making good the walls etc. (DSR 18.10) 15 mm dia

20 mm dia

25 mm dia

Providing, fixing and jointing gun metal gate valve with C.I. Wheel of approved quality (Screwed end) (DSR 18.17). 20 mm dia

25 mm dia

Providing for fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New Work). (DSR 18.46). 15 mm dia meter

20 mm dia metre

25 mm dia metre

Providing & Fixing in position gully traps fixed in cement concrete 1:4:8 complete with H.C.I. grating 150 mm x 150 mm cast iron cover weighing approximately 7.26 Kg. and frame clear opening 300 mm x 300 mm and outside size 330 mm x 330 mm and chamber including cost of all brick work in cement mortar 1:5 cement concrete 1:2:4, in coping black bitumastic superior paint of approved manufacture on all C.I. work as per standard design, minimum depth of water should be 150 mm with a minimum seal 50 mm. (b) 100 internal diameter H.C.I. gull trap. (HSR 30.114 (b)).

Providing and fixing in position automatic brass ball valves in tanks. (b) With Plastic Ball (ii) 20 mm internal diameter. [HSR 30.110 (b) (ii)].

Providing & Fixing H.C.I. floor traps I.S.I. marked of the self cleaning design with C.P. brass hinged grating with frame with or without vent arm and including cement concrete 1:2:4 under and around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors, etc. minimum depth of water should be 50 mm with a minimum seal of 50 mm. (b) with 75 mm i/d outlet. [HSR 30.89 (b)].

Providing and fixing in position C.I. Gully trap cover weighing approximately 7.26 Kg. and frame for gully trap chamber clear opening size 300 mm x 300 mm and out side size 330 mm x 330 mm including painting the exposed surfaces with 3 coats of black bitumastic superior paint of approved manufacture etc. (HSR 30.85).

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making goods the walls etc. (a) C.P. Brass (i) Soap dish Large. [HSR 30.70 (a) (i)].

Providing and fixing in position glass shelf fixed in with rawl plugs with C.P. Brass screws, complete including cutting and making good the walls etc. (a) with C.P. Brass brackets and guard rail. (i) 600mm x 125 mm . [HSR 30.69 (a) (i)].

Providing and fixing in position best Indian make towel rails fixed in with rawlslugs embedded in walls with C.P. Brass screws, complete in all respect including cutting and making goods the walls etc.: (a) 25 mm dia, C.P. Brass adjustable. (i) 750 mm long. [HSR 30.68 (a)]

Constructing brick masonry inspection chamber sizes as given below upto 0.60 metre average depth in cement mortar 1:5 lime concrete with 40 percent limer mortar 2:3 in foundation cement concrete 1:2:4 benching 12 mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement R.C.C. 1:2;4 slab 100 mm thick./C.C. topping 50 mm thick with 455 mm x 455 mm 610 mm inside light duty C.I. inspection chamber cover and frame weight as per I.S.I. specification painted with 3 coats of black bitumastic superior paint coplete as per standard design. [HSR 29.84]. (a) Size 450 mm x 450 mm

(b) Size 450 mm x 600 mm

Providing & fixing in position best Indian make bevelled edge 5.5 mm thick mirror mounted on absetos sheet ground fixed in postion by means of 4 Nos. chromium plated brass screws and washers over rubbers washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the engineer-in-charge) complete including cutting and making good the walls etc. (a) Indian Make (i) 600 mm x 450 mm. [HSR 30.71 (a) (i)].

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge). (HSR 30.75 (C)). Bib cock long body

Bib cock.

PROVIDING AND FIXINGIN POSITION H.C.I.SOIL WASTE VENT OR ANTISYPHONAGE PIPES TO I.S.I. SPECIFIACTION OF E.L.C. MANUFACTURE OR OF ANY OTHER REPUTED FIRM NCLUDING CUTTING AND WASTAGE ETC. AND CUTTING HOLES IN WALLS, ROOFS OR FLOOR ETC.AND MAKING GOOD to its original condition BUT EXCLUDING COST OF LEAD OINTING.(HSR 30.84)

Supply and erection of Taps of made of Gun metal ISI marked including all labour and material required to complete the job in all respect (NS) 15 mm internal diameter of pipe line

20 mm internal diameter of pipe line

Pdg. & Fixing of Europeon type seal cover with Jet pressure complete in all respect (NS)

Recovery Items:- The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the price quoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under :- Bricks / Tiles @ 4.50/- Each

Bricks Bats @ 400/- P. Cum

Steel @ 3000/- P. Qtl

Doors @ 1000/- Each

Windows @ 500/- Each Note:- 1. In case of any difference in the unit & nomenclature of any of the DSR Items of Civil, P.H. work depicted in this DNIT and that given in DSR, the unit and nomenclature given in DSR shall be applicable. 2. Only reputed make material will be used (make-brand exhibited in DSR and exhibited in apporoved standard document) as apporved by Engineer-in-Charge, while executing various items / works at site.

The Teg Bahadur Co-Op L/C Society Limited Siwan

The Shree Radhe Co op L and C Society Ltd. Cheeka

THE DHIMAN CO OP L AND C SOCIETY