Provn of 01 x Toilet Block with 10 x WC, 05 x Wash Basin and other fittings near Bldg No P-11 and connected works under GE (N) Bikaner at Mil Stn Bikaner

Amount

Site clearance in soft and loose soil complete all as specified & as directed.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil all as specified and as directed.

Excavation over areas not exc 1.5m deep and getting out in soft/loose soil complete all as specified and as directed.

Excavation over areas depth exc 1.5m and not exc 3m and getting out in soft/loose soil complete all as specified and as directed.

Excavating in trenches, not exc 1.5 metre wide and not exc 1.5 metre in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. laying cables, pipes, etc. not exc 10 Sqm on plan & not exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed.

All as per serial item No. 5.00 here-in-before but depth exc 1.5m and not exc 3m.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil complete all as specified and as directed.

Removing excavated soil/material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified and as directed.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as specified and as directed..

M&L for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for cement concrete (1:2:4) type B1 using 20 mm graded crushed stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement complete all as specified and as directed.

M&L for precast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in CM (1:6) complete all as specified & as directed.

M&L for cement concrete 1:3:6 type C0 using 12.5mm graded crushed stone aggregate as in filling up chowkat/frame hollows, lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, filling up chowkat/frame hollows, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified & as directed.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams, bases for columns, mass concrete and the like all as specified and as directed.. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in columns, pillars, piers, posts, struts and the like all as specified and as directed.. Note :- Reinforcement & formwork shall be measured and paid for separately

M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded crushed stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span and the like all as specified and as directed.. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded crushed stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like complete all as specified & as directed. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded crushed stone aggregate in chajjas and the like all as specified and as directed. Note :- Reinforcement & formwork shall be measured and paid for separately.

Supply only integral liquid water proofing compound (ISI marked) complete all as specified & as directed.

M&L for brick work with old size Fly Ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with old size Fly Ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:4 complete all as specified and as directed.

M&L for brick work with old size burnt clay sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:4 complete all as specified and as directed. Note : Brick work under this item shall be carried out in sewage disposal work (i.e. manholes) and area drainage work (i.e. drains).

M&L for brick work with old size Fly Ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

M&L for brick work with old size sub-class ‘B’ bricks, in brick-on-edge walls (less than 1/2 brick thick) built in cement mortar 1:4 complete all as specified and as directed..

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete all as specified and as directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete all as specified and as directed..

Formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete all as specified and as directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified & as directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs, shelves and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for rough finished surfaces of concrete complete all as specified & as directed.

Supply and fixing factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & as directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube in opening as per specifications complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and as directed.

S&F butt hinges of size 100mm medium weight, cold rolled mild steel (ISI marked) complete all as specified and as directed.

S&F butt hinges of size 100mm extruded aluminium alloy with galvanized mild steel hinge pin, anodized type B-21 complete all as specified and as directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and as directed.

S&F extruded aluminium alloy handle, 150mm size, fabricated type, anodized (ISI marked) complete all as specified and as directed.

S&F steel locking bolts with mild steel electrogalvanised plate and bright bolt not less than 10mm dia 100mm size complete all as specified and as directed.

S&F 250 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm, complete all as specified and as directed.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified & as directed.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, framed signed boards, walk ways, railings, framework of water tanks and similar work including welding conforming to Grade E-165 (Fe 290), complete all as specified & as directed.

M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & as directed.

M&L for mild steel TMT bars 6 to 8 mm dia cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & as directed.

All as per serial item No. 44.00 here-in-before but 6 to 10mm dia in stirrups, spacers and binders.

S&F factory made pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, made out of mild steel sheet of 1.25 mm thickness, including making good the disturbed surfaces of wall etc in CM 1:4, complete as specified & as directed.

S&F factory fabricated pressed steel frame/box windows, ventilators with glazed and fly proof shutters provided to size and dimensions as specified & shown on drawing No. BTD-888R Sheet No. 1/5 to 5/5 & BTD-889 Sheet No. 1/4 to 4/4 or as directed by GE with & including MS grill, MS fillets, pintol hinges, tower bolts, MS handles, peg stays, MS lugs, locking arrangement, dash through bolt where required, etc complete all as specified & as directed. Notes : (i) PCC for filling in frames, glass, wire gauge and painting shall be measured & paid for separately under respective items. Provision of all other items as shown & specified on drawings shall deemed to be included in quoted rate of this item. (ii) The quoted rate shall deemed to include provision of cutting holes of suitable depth in walls for inserting lugs etc and making good dismantled portion in PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate and CM (1:3).

M&L for applying evenly a coat of industrial bitumen 85/25 grade at the rate of 1.20 Kg per sqm including cleaning surfaces of roof, sunken portion, etc, complete all as specified & as directed.

M&L for cleaning of all loose dirt and dust from roof and priming the surface with one coat of cold applied bituminous primer @ 0.40 litre/sqm and provide a layer of APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3mm thick, reinforced with polyester non woven fabric (weighing not less than 150 gms/sqm) laid on primed surface complete all as described in Para 11.44.5 of SSR Part-I, complete all as specified and as directed. Note : The net area of water proofing treatment shall be measured without any extra allowance for laps.

M&L for 75 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even, complete all as specified and as directed.

M&L for 25mm thick PCC (1:2:4) type B0 using 12.5mm graded crushed stone aggregate as in flooring, leveling course, etc, surface finished fair and even, complete all as specified and as directed.

M&L for machine cut Kota stone slab 20 to 25mm thick on vertical surfaces such as dado, skirting etc. laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab with true & uniform joints including rubbing and mirror polishing complete all as specified & as directed.

M&L for 20mm thick Granite (of any type) machine cut slab of approved shade (table rubbed and polished) with true & uniform joints as in steps, jambs, pillars, window cills, cooking platforms & like and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over & including 15mm thick screed bed (bedding layer) in CM 1:4 with cement slurry @ 3 Kg/Sqm complete all as specified & as directed. Note : The exposed edges of granite stone slab shall be made full round & polished to mirror finish and rate quoted shall deemed to include this provision.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for glazed ceramic tiles (coloured) 7mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm (i.e 450mm x 350mm / 300mm x 450mm or as directed), on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for factory made 60mm thick machine pressed precast cement concrete interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and no pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & as directed. Note : Shape of paver blocks shall be as approved by the GE.

M&L for 75mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished even and smooth without using extra cement complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid with an outward slope of 1:30 in alternative bays not exceeding 4 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified & as directed.

M&L for 15mm thick rendering in two layer on fair faces of brick masonry or concrete surfaces of walls consisting of 1st layer of 10mm thick plaster in CM 1:4 and 2nd layer (setting coat or top layer) of 5 mm thick plaster in CM 1:4, 2nd layer mixed with integral liquid water proofing compound as per manufacturer’s instructions, finished fair & even, complete, all as specified and directed. Note : - Supply only integral liquid water proofing compound shall be measured and paid for separately.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, mixed with integral liquid water proofing compound as per manufacturer’s instructions, finished even & smooth without using extra cement, complete all as specified and directed. Note : Supply only integral liquid water proofing compound shall be measured and paid for separately.

M&L for rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified & directed.

M&L for Flush pointing to brick walls in cement mortar 1:4 complete all as specified & as directed.

M&L for preparation of newly plastered / unplastered surfaces of walls & applying three coats of white wash complete all as specified.

M&L for preparation of newly plastered / unplastered surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint over a coat of alkali resistant priming paint complete all as specified & as directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified & as directed.

S&F 4mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified & as directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified & as directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of red oxide, zinc chrome primer complete all as specified & as directed.

Supply & fixing mild steel clamps made of flat iron 40x6mm in two halves for tapping through 40 to 80mm bore GI/CI/DI water pipe line including drilling and welding of 15/20mm GI socket and necessary rubber insertion, nut, bolts & washers, complete all as directed.

M&L for galvanized steel water tubing medium grade (ISI marked) of 15mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

M&L for galvanized steel water tubing medium grade (ISI marked) of 20mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

M&L for galvanized steel water tubing medium grade (ISI marked) of 20mm bore with & including all fittings complete laid in trenches all as specified and as directed.. Note :- Excavation & earthwork shall be measured & paid for separately.

M&L for galvanized steel water tubing medium grade (ISI marked) of 50mm bore with & including all fittings complete laid in trenches all as specified and as directed.. Note :- Excavation & earthwork shall be measured & paid for separately.

S&F 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top), ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed.

S&F vitreous china squatting pan, ‘Orissa’ pattern, white, size 580x440mm with integral foot rests, ‘P’ or ‘S’ trap, including connection to trap and flushing pipe, antisyphonage pipe etc, complete all as specified and as directed.

S&F PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified & as directed.

S&F vitreous china counter sunk wash hand basin white of size 460mm x 310mm x 220mm with & including 32mm dia PVC waste pipe and 32 mm chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed complete all as directed. Make : Cat Part No. "4793 (NIALL)" of make "Prayag" or equivalent in makes mentioned in Appendix 'B' here-in-after.

S&F PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified & as directed.

S&F 15 mm bore bib tap, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & as directed.

S&F 15mm bore Angle stop valve, fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union complete all as specified & as directed.

S&F Centre hole mixer for mixing hot & cold water for wash hand basin, cast copper alloy, with dual capstan heads, chromium plated, screwed down high pressure, with lettered 'Hot' & 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe suitable for 15mm bore, complete all as specified as directed.

S&F brass chromium plated wall mixer for mixing hot & cold water with connecting legs and wall flanges screwed down for iron pipe of 15mm bore all as specified and as directed

S&F 20mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete all as specified & directed.

S&F 50mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete all as specified & directed.

S&F stainless steel peg set of six fixed to wall with two rawl plugs and chromium plated (CP) brass screws complete all as directed.

S&F Shower rose, round type, brass, chromium plated, Fancy type, 125 mm dia with or without swivel joint, with & including CP brass arm and wall flange, fixing to steel pipe of 15mm bore or union complete all as specified and as directed.

S&F Soap dish, brass, chromium plated, heavy duty, fixed to wall with plugs with brass cadmium plated screws, complete all as specified and as directed.

S&F Towel Ring of PTMT fixed with and including Chromium plated brass screws and plastic cleats (Minimum weight 90gms) complete all as specified & as directed.

Supply and fixing 100 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, laid in trenches or floors, complete all as specified and as directed.

Supply and fixing 75 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, laid in trenches or floors, complete all as specified and as directed.

Supply and fixing 50 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, complete all as specified and as directed.

S&F stack clamp made out of MS flat 50mm x 5mm and 16 mm dia round iron stays, including bolts & nuts, securing ends of stays to walls or roof for 50mm bore pipe including two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified & as directed.

S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified & as directed.

S&F 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified & as directed.

Supply and fixing cast iron cowl for 50 mm bore CI pipe complete all as specified.

Extra over cast iron pipe & fitting 100mm bore providing lead joints in lieu of cement joints complete all as specified and as directed.

Extra over cast iron pipe & fitting 75mm bore providing lead joints in lieu of cement joints complete all as specified and as directed.

S&F cast iron trap ‘P’ or ‘S’ for 100 mm bore pipe complete all as specified & as directed.

S&F cast iron floor trap of 75 mm bore, with grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4), complete all as specified & as directed

S&F salt glazed stone ware drain pipes of 150mm bore, Class ‘SP 2’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified & as directed.

M&L for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate in bedding to SGSW drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and as directed.

M&L for cutting into existing manholes/Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1, reforming benching as required and finishing surface even & smooth for 150mm bore pipe complete all as specified and as directed.

M&L for point wiring for one light/fan/bell/buzzer point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including non-metallic rigid PVC concealed conduit (medium duty, ISI marked, not less than 20mm dia) with all fittings such as tee, bends, etc all as per IS, terminated in & including new sunk type pressed steel terminal boxes concealed in wall for mounting fittings like switches, sockets, regulators etc with and including 3mm thick phenolic laminated sheet top cover, complete all as specified and as directed. Note : Cost of cutting/leaving forming chases for conduits, sinking for boxes and making good in CM 1:4 shall deemed to be included in quoted rate of this item.

All as per serial item No. 106.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board with other switches.

S&F switch piano, flush type, single pole, one way, 6 Amp, ISI marked, complete all as specified and as directed.

S&F socket outlet, 3 pin (2 in 1, with 2 pin outlet also), 6 Amp, flush type, ISI marked, complete all as specified and as directed.

S&F ceiling rose, PVC/Polycarbonate insulated body, 65mmx50mm with three terminals, ISI marked, complete all as specified and as directed.

S&F lamp holder, PVC/Polycarbonate insulated body with back plate suitable for conduit/casing caping fittings, ISI marked, complete all as specified and as directed.

S&F 9 Watt LED Bulb (Non-dimmable) of Standard / Universal size, Base - B22, Power Factor > 0.90, Lamp Efficiency > 80%,, Color Temperature - 3000 K, Lumen output - 900 lm, Colour Rendering Index (CRI) > 70, Warm white (WW) / Cool Day Light (CDL), 230 V, 50 Hz AC, ISI marked, complete all as specified and as directed.

S&F energy efficient decorative ultra slim LED light fitting, 1x20 Watt, 230 Volts, Day Cool light, batten type with driver & polycarbonate housing including tube rod and all accessories, prewired and connecting up with & including 3 core sheathed flexible copper cable 1.5 sqmm of suitable length upto light point/ceiling rose, complete all as specified and as directed. Make : Havells Cat Part No. LUMILINEBS20WLED865SPCWH or equivalent in makes mentioned in Appendix 'B' here-in-after.

Supply, installation, commissioning & testing Light Emitting Diode (LED) based street/security light fitting, 25 Watt with & including LED lamp, housing made up of LM6 pressure die cast aluminium alloy with effective thermal management, sturdiness, monolithic construction, totally enclosed, dust and water proof, minimum system efficiency of more than 100 lumens per watt and a minimum system lumen output of not less than 2500 lumens, correlated colour temperature shall be minimum 5700 degree Kelvin, Colour Rendering Index (CRI) shall not be less than 70, fitting shall be designed for a system life of 50,000 hours @ 70% lumen maintenance, ingress protection of IP-65 (minimum), mechanical impact resistance rating of IK ≥ 07, operating voltage range 140 V to 270 V, AC, frequency 50-60Hz, potted type for humming free operation, driver shall withstand upto 400 V for 08 hours, surge protection not less than 10 KV, Power factor > 0.95, Total Harmonic Distortion (THD) shall be less than 15%, double phase protection, no load, open circuit and short circuit protection, suitable for ambient temperature from (-)10°C to 50°C and humidity level 10% to 90% RH, cool white colour and lamp starting time shall not be more than 10 second, PMMA/polycarbonate/toughened glass heat resistant cover, prewired and connecting up to street light feeder/junction box with & including 2.5 Sqmm 3 core PVC insulated, weather proof, multistranded copper conductor cable of 1100 Volt grade (ISI marked), complete all as specified and as directed.

NOTES FOR LED LIGHT FITTINGS : (i) All LED light/luminare shall meet the provision laid down in IS - 16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part -II / Section 13. (ii) Contractor shall submit test report of LED street light fitting from Government accredited test laboratory for LM-79 and LM-80. (iii) Contractor has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of contract. The product will be replaced on site free of cost in the following case :- (a) Manufacturing defects. (b) Failure due to mechanical and electrical impact. (c) Drop in lumen (or lux at 1 m) below 90% of claimed values of lumen (or lux at 1 m) of the LED /Luminaries.

Supply and fixing mounting bracket (suitable for fixing/holding street/security light fittings) made of 40mm bore GI pipe ‘light grade’ not less than 1.20m long, bent to shape at required angle, fixed to Pole/wall with & including mild steel clamps (02 Nos) made out of flat iron 50x6mm with nuts, bolts & washers, matching with section of Pole/suitable for wall, complete all as specified and as directed.

S&F sheet metal enclosure, double door type, suitable for fixing MCBs, SPN with 200 Amps rated bus bar, 4 way, 240 Volts, complete all as specified and as directed.

S&F MCB, 6 to 32 Amps, Single Pole, 240 Volts, 10 kA, ‘C’ Curve, with over load and short circuit protection, ISI marked, complete all as specified and as directed.

S&F MCB, 6 to 32 Amps, SPN, 240 Volts, 10 kA, ‘C’ Curve, with over load and short circuit protection, ISI marked, complete all as specified and as directed..

Supply & fixing Exhaust fan of 225mm sweep, heavy duty, double ball bearing, copper wound, steel body, 900 RPM, Single Phase 230 Volt, 50 Hz AC supply complete with blades, frame and louver shutter and connecting up with & including three core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2 mm drawn into & including flexible PVC conduit and fixed by using 4 Nos, 100mm long 8mm dia bolt nuts and washers and grouted in wall in CM (1:3) with and including making suitable opening in existing wall complete all as specified & as directed

Material and labour for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 7.50 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40 mm thick RCC pit cover, etc complete all as specified & as directed. Note : PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable (ISI marked) with aluminium stranded conductor 1100 Volt grade cross sectional area 10 sqmm 2 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified and directed. Notes :- (i) Sand cushioning, cable protection cover and excavation & earth work shall be measured & paid for separately. (ii) LT cable wherever directed shall be laid through existing GI protection pipe. Cable shall be connected to existing junction boxes with suitable thimbles/lugs. Quoted rates shall deemed to include for same.

M&L for dry sand (Local Tibba sand) and punning for cushioning and cover for protection of under ground electric cable complete all as specified and as directed. Notes :- (i) Approved local Tibba dry sand free from vegetations, grass and other deleterious substances shall be used. (ii) For the purpose of payment, only punned thickness shall be measured.

M&L for sub class ‘B’ (old size) burnt clay bricks laid flat and dry abutting each other with gap between adjacent bricks not exc. 10mm for protection of underground electric cable in such a way that the length of brick is at right angle to the central axis of cable complete all as specified and as directed.

M&L for Galvanized iron tubing, 40mm bore light grade, ISI marked, including all fittings and laid in trenches/under road/drains, fixed to poles/walls with required size of flat iron (25mmx3mm) clamps, bolts, nuts and washers for protection of LT electric cable complete all as specified and as directed. Note :- Excavation & earthwork shall be measured & paid for separately.

VIJAY KUMAR SHARMA

M/s Sharafat Farook