REPAIR MAINT POLISHING OF WOODEN FURNITURE AT BSO UNDER GE FAIZABAD

Amount

REPAIR TO PEG TABLE :-Taking out old unserviceable top and S&F new top of peg table of size 450 mm x 300 mm of 19mm thick prelaminated particle board BWR grade, bonded with phenol formaldehyde synthetic resin adhesive with malamine finish ISI marked IS-12823 (1990). Gde-I type II having desired shade on one side and balancing white lamination on other side, including 6mm thick teak wood edging all around with Fevicol and nails complete all as shown on drawing as specified & directed by EIC.

All as per item No 1 but Bottom rail of size 40 mm x 20 mm of Ist class hard wood (Teak) complete all as shown on drawing as specified & directed by EIC.

All as per item No 1 but Top rail of size 40 mm x 20 mm of Ist class hard wood (Teak) complete all as shown on drawing as specified & directed by EIC.

All as per item No 1 but legs of size 50 mm x 30 mm of Ist class hard wood (Teak) complete all as shown on drawing as specified & directed by EIC.

Taking out old unserviceable hard rubber ring with screw (steel) and S&F new hard rubber ring of superior quality fixed with screws (steel) of suitable size to the bottom of leg complete as approved and all as shown on drawing by EIC.

M&L for French polishing one coat to old and two coats to new surface including preparation of surface of peg table, complete all as shown on drawing as specified & directed by EIC.

REPAIR TO TABLE 3' X 2' WITHOUT DRAWER :- Taking out old unserviceable top and S&F new top of Table 3' x 2' without drawer of size 900 mm x 600 mm of 19mm thick prelaminated particle board BWR grade, bended with phenol formaldehyde synthetic resin adhesive with malamine finish ISI marked IS-12823 (1990). Gde-I type II having desired shade on one side and balancing white lamination on other side, including 6mm thick teak wood edging all around with Fevicol and nails complete all as shown on drawing as specified & directed by EIC.

All as per item No 7 but long rail of section size 60 mm x 20 mm & 900 mm long.

All as per item No 7 but short rail of section size 60 mm x 20 mm & 600 mm long of Ist class hard wood (Teak) complete all as shown on drawing as specified & directed by EIC.

All as per item No 7 but legs of size 30 mm x 60 mm & 740 mm long of Ist class hard wood (Teak) complete all as shown on drawing as specified & directed by EIC.

Taking out old unserviceable hard rubber ring with screw (steel) and S&F new hard rubber ring of superior quality fixed with screws (steel) of suitable size to the bottom of leg complete as approved and all as shown on drawing by EIC.

M&L for French polishing one coat to old and two coats to new surface including preparation of surface of Table 3' x 2' without drawer and Table 3' x 2' with drawer complete all as shown on drawing as specified & directed by EIC.

REPAIR TO TABLE 3' X 2' WITH DRAWER :- Taking out old unserviceable top and S&F new top of Table 3' x 2' with drawer of size 900 mm x 600 mm of 19mm thick prelaminated particle board BWR grade, bended with phenol formaldehyde synthetic resin adhesive with malamine finish ISI marked IS-12823 (1990). Gde-I type II having desired shade on one side and balancing white lamination on other side, including 6mm thick teak wood edging all around with Fevicol and nails complete all as shown on drawing as specified & directed by EIC.

All as per item No 13 but long rail of section size 60 mm x 20 mm & 900 mm long.

All as per item No 13 but short rail of section size 60 mm x 20 mm & 600 mm long of Ist class hard wood (Teak) complete all as shown on drawing as specified & directed by EIC.

All as per item No 13 but legs of size 30 mm x 60 mm & 740 mm long of Ist class hard wood (Teak) complete all as shown on drawing as specified & directed by EIC.

All as per item No 13 but drawer including brass knob complete all as shown on drawing as specified & directed by EIC.

Taking out old unserviceable hard rubber ring with screw (steel) and S&F new hard rubber ring of superior quality fixed with screws (steel) of suitable size to the bottom of leg complete as specified and all as shown on drawing by EIC.

M&L for French polishing one coat to old and two coats to new surface including preparation of surface of Table 3' x 2' without drawer and Table 3' x 2' with drawer complete all as shown on drawing as specified & directed by EIC.

REPAIR TO CHAIR WRITING/CBA :- Removing & taking out carefully of old existing unserviceable broken back leg of the chair writing/CBA of any description in any position & replacement of the same with S&F new back leg of 1st class hard wood (teak wood) made to shape, fixed in position all as shown on drawing specified and directed by Engr-in-Charge.

All as per item No. 20 here-in-before but front leg.

All as per item No. 20 here-in-before but replacement of side rail with S&F new rail made out of 1st class hard wood (Teak) with holes for weaving. The spacing of holes shall match with the existing rail on other side.

All as per item No. 20 here-in- before but replacement of front or back rail.

All as per item No.20 here-in before but replacement of back strip with new back strip made out of 1st class hard wood (Teak) complete all as shown on drawing

All as per item No. 20 here-in-before but replacement Arm rest with S&F new Arm rest made out of 1st class hard wood (Teak) complete as shown on drawing.

All as per item No.20 here-in-before but replacement of stiffener (center or left side or Right side) and S&F new made out of 1st class hard wood (Teak) complete all as shown on drawing.

All as per item No. 20 here-in-before but replacement of rubber ring and S&F new hard rubber ring of superior quality under the leg with steel plated screw of size 20mm long complete as approved and all as shown on drawings.

M&Lfor removing old unserviceable plastic cane from Chair writing/CBA and supply and recane with new plastic cane of size 2mm wide and 0.4mm thick half round Godrej pattern with approved best quality plastic cane all as specified and directed by EIC.

M&L for polishing two coats of old and new surfaces of chair writing/CBA after repair with French polish of approved make including preparation of surfaces all as directed by EIC.

REPAIR TO CHAIR EASY :- Removing taking out carefully of old existing unserviceable broken back leg of the chair easy of sorts any description in any position & replacement of the same with S&F new back leg of 1st class hard wood (Teak) made to shape, fixed in position all as shown on drawing and directed by the Engr-in-Charge

All as per item No. 30 here-in-before but for front leg.

All as per item No. 30 here-in-before but replacement of side rail for seat and S&F new rail made out of 1st class hard wood (Teak) with holes for weaving. The spacing of holes shall match with the existing rail of other side.

All as per item No. 30 here-in- before but replacement of front or back rail for seat and S&F new front or back rail made out of 1st class hard wood (Teak) with holds for cane weaving. The spacing of holes shall match with the existing rail on other side.

All as per item No. 30 here-in before but replacement of Left or Right Rail for back frame made out of 1st class hard wood (Teak) with holes for cane weaving. The spacing of holes shall match with existing rail on other side.

All as per item No. 30 here-in-before but replacement of top or bottom rail for back frame with S&F new top or bottom cane weaving. The spacing of holes shall match with the existing rail on other side, complete all as shown on drawing.

All as per item No. 30 here-in-before but replacement of front and back support rail and S&F new front and back support rail out of 1 st class hard wood (Teak) complete all as shown on drawing.

All as per item No. 30 here-in-before but replacement of Arm rest and S&F new Arm rest made out of 1st class hard wood (Teak) complete as shown on drawing.

All as per item No. 30 here-in-before but replacement of rubber ring and S&F new hard rubber ring under the leg of superior quality with steel plated screw of size 20mm long complete as approved and all as shown on drawings.

M&Lfor removing old unserviceable plastic cane from Chair Easy (both seat & back) and supply recaning with new plastic cane of size 2mm wide and 0.4mm thick half round complete all as specified and as per Godrej pattern with approved best quality plastic cane all as specified and directed by EIC.

M&L for polishing two coats of old and new surfaces of chair easy after repair with French polish of approved make incl preparation of surfaces all as directed by Engr-in-Charge.

REPAIR TO CHAIR DINING :- Removing taking out carefully of old existing unsv broken back leg of the chair dining CBB of any description in any position & replacement of the same with new back leg of 1st class hard wood (Teak) made to shape, fixed in position, complete all as shown on drawing specified and directed by Engr-in-Charge.

All as per item No. 41 here-in-before but for front leg.

All as per item No. 41 here-in-before but replacement of side rail and S&F new side rail made out of 1st class hard wood (Teak) with holes for weaving. The spacing of holes shall match with the existing rail of other side.

All as per item No. 41 here-in- before but replacement of front or back rail and S&F new front or back rail made of 1st class hard wood (Teak) with holes for weaving. The spacing of holes shall match with the existing rail on other side.

All as per item No. 41 here-in before but replacement of stiffener (center or left side or right side) and new stiffener made out of 1st class hard wood (Teak) complete all as shown on drawing.

All as per item No. 41 here-in-before but replacement of back strip and S&F new back strip made out of 1 st class hard wood (Teak) complete all as shown on drawing.

All as per item No. 41 here-in-before but replacement of rubber ring and under the leg of superior quality with steel plated screw of size 20mm long complete as approved and all as shown on drawings.

M&Lfor removing old unserviceable plastic cane from Chair Dining and supply and recane with new plastic cane of size 2mm wide and 0.4mm thick half round Godrej pattern with approved best quality plastic cane all as specified and directed by EIC.

M&L for polishing two coats of old and new surfaces of chair dining after repair with French polish of approved make including preparation of surfaces all as directed by EIC.

REPAIR TO CHAIR VARANDAH :- M&L for removing old cane and recaning of Chair Varandah with & including new plastic cane including painting with two coats of white synthetic enamelled paint on entire steel / iron surface of chair before recaning and including provision of new hard rubber toes 15 mm dia. at bottom of legs after taking out old ones complete all as specified.

REPAIR TO TABLE DINING 6 PERSONS :- Taking out old unserviceable top of table 1500 mm x 900 mm and S&F new top of size 1500 mm x 900 mm made out of 18mm pre-laminated particle board, edges duly covered with 6 mm thick teak wood beading complete all as shown on drawing as specified & directed by Engr-in-Charge.

All as per item No 51 but leg of table dining 6 persons of section size 75 mm x 40 mm x 740 mm made out of first class hard wood (Shisham).

All as per item No 51 but long rail of table dining 6 persons of section size 100 mm x 25 mm & 1500 mm long.

All as per item No 51 but short rail of table dining 6 persons and section size 100 mm x 25 mm & 900 mm long.

Taking out old unserviceable hard rubber ring with screw (steel) and S&F new hard rubber ring of superior quality fixed with screws (steel) of suitable size to the bottom of leg complete as approved and all as shown on drawing by Engr-in-Charge.

M&L for French polishing one coat to old and two coats to new surface including preparation of surface of table dining 6 persons complete all as shown on drawing as specified & directed by Engr-in-Charge.

REPAIR TO TABLE DINING 8 PERSONS :-. Taking out old unserviceable Top of table dining 8 persons and S&F new top of size 1800 mm x 900 mm of 18mm thick prelaminated particle board BWR grade, bended with phenol formaldehyde synthetic resin adhesive with malamine finish ISI marked IS-12823 (1990). Gde-I type II having desired shade on one side and balancing white lamination on other side, including 6mm thick teak wood edging all around with Fevicol and nails complete all as shown on drawing as specified & directed by EIC.

All as per item No 57 but legs of section size 75 mm x 40 mm x 740 mm of Ist class hard wood (Teak) complete all as shown on drawing as specified & directed by EIC.

All as per item No 57 but long rail of section size 100 mm x 25 mm & 1800 mm long.

All as per item No 57 but short rail of section size 100 mm x 25 mm & 900 mm long.

Taking out old u/s hard rubber ring with screw (steel) and S&F new hard rubber ring of superior quality fixed with screws (steel) of suitable size to the bottom of leg complete as approved and all as shown on drawing by EIC.

M&L for French polishing one coat to old and two coats to new surface including preparation of surface of table dining 8 persons complete all as shown on drawing as specified & directed by EIC.

REPAIRS TO TABLE CENTRE :- Dismantling / taking out carefully & replacement of old existing broken top of table centre of any description in any position and replacement of the same with S&F new top with 18 mm thick prelaminated particle board (Make-Eco/Novapan) one side teak face lamination & other side white balancing, exterior grade, BWP, flat pressed three layered, bonded with phenol formaldehyde synthetic resin, ISI marked with and including 6 mm thick teak wood beading all round made to shape fixed in position as shown on drawing complete all as specified and directed by Engr-in-charge.

Taking out old unserviceable legs from table and S&F new teak wood legs made to shape as shown on drawing complete all as specified and directed by Engr-in-charge.

Taking out old unserviceable long rail from table and S&F new teak wood long rails made to shape as shown on drawing complete all as specified and directed by Engr-in-charge.

Taking out old unserviceable short rail from table and S&F new teak wood short rail made to shape as shown on drawing complete all as specified and directed by Engr-in-charge.

M & L for polishing one coat of old surface and two coats to new surfaces of Table Centre with French polish as shown on drawing complete all as specified and directed by Engr-in-charge.

M & L for replacement of rubber ring with under the leg of superior quality with steel plated screw of size 20 mm long as shown on drawing complete all as specified and directed by Engr-in-charge.

REPAIR TO TABLE WRITING:-. Dismantling/taking out carefully old existing broken table top of any description in any position and replacement of the same with S & F new top with 18 mm thick pre-laminated wood particles board (Eco/Novapan) exterior grade BWP melamine faced, flat pressed, three layered, bonded with phenol formaldehyde synthetic reisin, ISI marked with 6 mm thick teak wood beading alround made to shape fixed in position as shown on drawing with material and labour complete all as specified and directed by Engr-in-charge.

Replacement of shutter with S & F 18 mm thick veneered particle board one side teak veneered as shown on drawing complete all as specified and directed by Engr-in-charge.

Replacement of top long rail with S&F new top long rails made out of 1st class hard wood (MP teak) as shown on drawing complete all as specified and directed by Engr-in-charge.

Replacement of top short rail with S&F new top short rails made out of 1st class hard wood (MP teak) as shown on drawing complete all as specified and directed by Engr-in-charge.

Replacement of drawer including brass knob with S&F new drawer made out of 1st class hard wood (MP teak) with knob brass chromium plated 40 mm dia as shown on drawing complete all as specified and directed by Engr-in-charge.

Replacement of leg with S&F new made out of 1st class hard wood (MP teak) as shown on drawing complete all as specified and directed by Engr-in-charge.

Replacement of bottom centre stiffener with S&F new bottom centre stiffenrer made out of 1st class hard wood (MP teak) as shown on drawing complete all as specified and directed by Engr-in-charge.

Replacement of bottom side (left or right) stiffener with S&F new bottom side (left or right) stiffenrer made out of 1st class hard wood (MP teak) as shown on drawing complete all as specified and directed by Engr-in-charge.

Replacement of hard rubber ring with steel screw with S&F new hard rubber ring under the leg, superior quality with steel screws of suitable size as shown on drawing complete all as specified and directed by Engr-in-charge.

M & L for polishing two coats to old and new surfaces of table writing after repair with French polish of approved make including preparation of surface complete all as specified and directed by Engr-in-charge.

REPAIR TO SIDE BOARD :-Taking out old unserviceable Top of side board and S&F new top of size 1225x460mm made out of 18/19mm prelaminated particle board (Make: NOVAPAN & NEPALBOARD) edges duly covered with 6mm thick teal wood beading complete all as shown on drawing as specified & directed by Engineer in charge.

All as per item No 79 but side of side board of size 615x460mm.

All as per item No 79 but bottom of side board of size 1225x460mm made out os 19mm block board

All as per item No 79 but ply wood back side of side board of size 1225x615mm made out of 6mm thick ply wood, Make- Kitply

All as per item No 79 but shutters of side board of size 380x600mm made out of 18/19mm prelaminated particle board (Make- NOVAPAN & NEPALBOARD), edges duly covered with 6mm thick teak wood beading and have two knob of 50mm size with locking device fixed to side board (Mke- GODREJ) with piano type contineous hinges complete all as shown on drawing as specified & directed by Engineer in charge.

All as per item No 79 but centre partition on of side board of size 550x460mm.

All as per item No 79 but shelf of side board of size 775x430mm.

All as per item No 79 but front portion of drawer of side board of size as specified made out of 18/19mm prelaminated particle board ( Make: NOVAPAN & NEPALBOARD) with one knob of 50mm size complete all as shown on drawing as specified and directed by Engineer in charge.

All as per item No 79 but side portion of drawer of side board of size as specified made out of 12mm first class hard wood plank (SHISHAM) with adhesive and nails complete all as shown on drawing as specified & directed by Engineer in charge.

Taking out old unserviceable back portion of drawer of side board and S&F new back portion of drawer of side board of size board of size as specifed made out of 12mm first class hard wood plank (SHISHAM) with adhesive and nails complete all as shown on drawing as speified & directed by Engineer in charge.

Taking out old unserviceable bottom portion of drawer of side board and S&F new bottom portion of drawer made out of 6mm plywood of size 430x370mm fixed with adhesive and nails complete all as shown on drawing as specified & directed by Engineer in charge.

Taking out old unserviceable long rail form bottom frame of side board and S&F new long rail for bottom frame of size 1020x45x25mm made out of first class hard wood (SHISHAM) complete all as shown on drawing as specified by Engineer in charge.

Taking out old unserviceable short rail form bottom frame of side board and S&F new short rail for bottom frame of size 360x45x25mm made out of first class hard wood (SHISHAM) complete all as shown on drawign ans specified by Engineer in charge.

Taking out old unserviceable legs form bottom frame of side board and S&F new legs for bottom frame of size 130x50x25mm made out of first class hard wood (SHISHAM) complete all as shown on drawign ans specified by Engineer in charge.

Taking out old unserviceable tower bolt of shutter of side board and S&F new tower bolte of shutter of size 55mm complete all as shown on drawing as specified & directed by Engineer in charge.

Taking out old unserviceable Mild steel chromium plated magnetic catch/ball spring of shutters of side board and S&F new Mild steel chromium plated magnetic catch/ball spring of shutters complete all as shown on drawign as specified and directed by Engineer in charge.

M&L for french polishing one coat to old and two coats to new surface including preparation of shuface of side boared, complete all as shown on drawing as specified and directed by Engineer Charge

REPAIR TO TABLE 900MMX900MMX760MM:- Taking out old unserviceable top of table 900x900mm and S&F new top of size 900x900mm made out of 18/19mm pre-laminated particle board, edges duly covered with 6mm thick teak wood beading complete all as shown on drawing as specified & directed by Engineer in charge.

All as per item No 96 but leg of Table 900x900mm of size 720x55x40mm made out of 1st class hard wood (Teak wood).

All as per item No 96 but rails for table 900x900mm of size 900x70x25mm made out of 1st class hard wood (Teak Wood).

Taking out old unserviceable hard rubber ring with screw (Steel) and S&F new hard rubber ring of superior quality fixed with screws (Steel) of suitable size to the bottom of leg complete as approved and all as shown on drawing by Engineer in charge.

M&L for french polishing one coat to old and two coats to new surface including preparation of shuface of table 900x900mm, complete all as shown on drawing as specified and directed by Engineer Charge

REPAIR TO TABLE DRESSING WITH LOOKING MIRROR LADIES :- Taking out old u/s looking mirror with frame of table dressing ladies and S&F new looking mirror with frame of size 400mm wide, 600mm hight, electrocopper plated mirror of polished sheet glass 5mm thick of Make- Modiguard/Swastic/Atul & Saint Gobain , 4mm thick ply wood back (05 ply grade CWR Type) and MS key plate 02 Nos complete all as shown on drawing as specified and directed by Engineer in charge,

Taking out old unserviceable top & bottom of table dresing ladies and S&F new top & bottom of table dressing ladies made out of 18/19mm thick prelaminated partile board (Make- Kitply/Bhutan board/ Nepal board/Archidlam/Eco board) of size as shown on dreawing, including 6mm thick teak wood edging to all exposd edges, complete all as shown on drawing as specified & directed by Engineer in Charge.

Taking out old unserviceable side, centre partition & shelf of table dresing ladies and S&F new side, centre partition & shelf of table dressing ladies made out of 18/19mm thick prelaminated partile board (Make- Kitply/Bhutan board/ Nepal board/Archidlam/Eco board) of size as shown on dreawing, including 6mm thick teak wood edging to all exposd edges, complete all as shown on drawing as specified & directed by Engineer in Charge.

Taking out old unserviceable complete drawer with brass knob of table dresing ladies and S&F new complete drawer with brass knob of table dressing ladies made out of 18/19mm thick prelaminated partile board and 6 mm ply (Make- Kitply/Bhutan board/ Nepal board/Archidlam/Eco board) of size as shown on dreawing, including 6mm thick teak wood edging to all exposd edges, complete all as shown on drawing as specified & directed by Engineer in Charge.

Taking out old unserviceable long rail form bottom frame of table dressing ladies and S&F new long rail for bottom frame of size 670x45x25mm made out of first class hard wood (SHISHAM) complete all as shown on drawing as specified and directed by Engineer in charge

Taking out old unserviceable short rail form bottom frame of table dressing ladies and S&F new short rail for bottom frame of size 250x45x25mm made out of first class hard wood (SHISHAM) complete all as shown on drawing as specified and directed by Engineer in charge

Taking out old unserviceable sliding glass with channel of table dressing ladies and S&F new sliding glass with channel made out of complete all as shown on drawing as specified and directed by Engineer in charge

Taking out old unserviceable legs form bottom frame of table dressing ladies and S&F new legs for bottom frame of size 160x45x25mm made out of first class hard wood (SHISHAM) complete all as shown on drawing as specified and directed by Engineer in charge

M&L for french polishing one coat to old and two coats to new surface including preparation of shuface of table dressing ladies, complete all as shown on drawing as specified and directed by Engineer Charge

REPAIR TO TABLE DRESSING WITH LOOKING MIRROR GENTS:- Taking out old unserviceable looking mirror with frame of table dressing gents and S&F new looking mirror with frame of size 410mm wide, 790mm hight, electrocopper plated mirror of polished sheet glass 5mm thick of Make - Modiguard/Swastic/Atul & Saint Gobain, all as specified with including teak wood frame, teakwood battens(size 25x35x1115mm long- 02 Nos) FI key plate & 6mm thick ply wood back (05 Nos Ply grade CWR type BB) including adhesive and nails etc. complete all as shown on drawing as specified & irected by Engineer in charge.

Taking out old unserviceable drawer of table dressing gents and S&F new drawer of table dressing gents, front of drawer shall be 12mm prelaminated particle board, side of drawer shall be 12mm thick teak wood plank and bottom & back of drawer shall be 6mm thick ply wood (05 Ply grade CWR type BB) size, shape & construction of drawer all as shown on drawaing including one knob of aluminum anodised dark brown shade duly fitted with screw, completed all as shown on drawing as specified and directed by Engineer in charge.

Taking out old unserviceable back of box of table dressing gents and S&F new back of box of table dressing gents, made out of 12mm thick wood plank of size 880x125mm including adhesive and nails etc, complete all as shown on drawing as specified and directed by Engineer in charge.

Taking out old unserviceable top, side, centre shelf & bottom of table dresing gents and S&F new top, side, center shelf & bottom of table dressing gents made out of 18/19mm thick prelaminated particle board of size as shown on dreawing, including 6mm thick teak wood edging to all exposed edges, complete all as shown on drawing as specified & directed by Engineer in charge

M&L for french polishing one coat to old and two coats to new surface including preparation of shuface of table dressing gents, complete all as shown on drawing as specified and directed by Engineer Charge

REPAIR TO HAT STAND WITH MIRROR- Taking out old unserviceable base of Hat Stand and S&F New base of Hat Stand of size as specified made out of 18/19mm prelaminated particle board, edges duly covered with 6mm thick teak wood beading fixed with adhesive and nails complete all as shown on drawing as specified & directed by Engineer in charge.

All as per item No 115 but Mirror 5/5.5mm thick, size as per drg (Make- Atul/Swastik/Saint Gobain )

All as per item No 115 but aluminium pegs with screws, size and sape as per drawing.

M&L Polishing with two coats of frech polish on old and new surface including preparition of surfaces of Hat Stand with Mirror complete all as shown on drawing as specified and directed by Engineer in charge,

REPAIR TO STOOL DRESSING CB . Taking out carefully of old existing userviceable leg of stool dressing CB, removing & replacement of the same with S&F new leg of stool dressing CB made out of 1st class hard wood (teak wood) suitable size in position all as shown on drawing complete all as specified and directed by Engr-in-Charge.

All as per item No119 here-in-before but replacement of side rail and S&F new side rail made out of 1st class hard wood (Teak wood) complete all as shown on drawing and directed by Engr-in-Charge.

All as per item No 119 here-in-before but replacement of long rail and S&F new long rail made out of 1st class hard wood (Teak wood) complete all as shown on drawing and directed by Engr-in-Charge.

All as per item No 119 here-in-before but replacement of rubber ring with steel screw and S&F new hard rubber ring of superior quality fixed with steel screw of suitable size to the bottom of leg complete as approved and all as shown on drawing.

M&L for polishing two coats of old and new surfaces of stool dressing CB after repair with French polish of approved make including preparation of surfaces all as directed by Engr-in-Charge and also removing old plastic cane and M&L for recaning of stool dressing CB with & including New plastic cane complete all as specified and directed by Engr-in-Charge.

REPAIR TO TEAPOY.:- Taking out old unserviceable top and S&F new top of Teapoy of size 450mmx600mm of 19mm thick prelaminated particle board BWR grade, bended with phenol formaldehyde synthetic resin adhesive with malamine finish ISI marked IS-12823(1990). Gde- I Type-II having desired shade on one side and balanceing white lamination on other side, including 6mm thick teak wood edging all around with Fevicol and Nails complete all as shown on drawing as specified & directed by Engr-in-Charge.

All as per tem No 124 but bottom rail of size 50x20mm of 1st class hard wood (Teak) complete all as shown on drawing as specified & directed by Engr-in-Charge.

All as per tem No 124 but Top rail of size 50x20mm of 1st class hared wood (Teak) complete all as shown on dreawing as specified & directed by Engr-in-Charge.

All as per tem No 124 but legs of size 60x20mm of 1st class hared wood (Teak) complete all as shown on dreawing as specified & directed by Engr-in-Charge.

Taking out old unserviceable hard rubber ring with screw (Steel) and S&F new hard rubber ring of superior quality fied with screws (Steel) of suitable size to the bottom of leg complete as approved and all as shown on drawing by Engr-in-Charge.

M&L for polishing with two coats of french polish on old and new surfaces including prepration of surfaces of Teapoy complete all as shown on drawing as specified & directed by Engr-in-Charge.

REPAIR TO TABLE BED SIDE :- Taking out old unserviceable top and S&F new top of table bed side of size 450x230mm of 18mm thick veneered particle board exterior grade BWP commercial face both side (Make- NOVAPAN/ECO BOARD) with 6mm thick teak wood beading alround made to shape fixed in position complete all as shown on drawing as specified & directed by Engr-in-Charge.

All as per tem No 130 but side of table bed side and S&F new sides with 12mm thick verneered particle board one side teak vernnered with 6mm thick beading complete all as shown on drawing as specified & directed by Engr-in-Charge.

All as per tem No 130 but bottom of table bed side and S&F new bottom with 12mm thick verneered particle board one side teak vernnered with 6mm thick beading complete all as shown on drawing as specified & directed by Engr-in-Charge.

All as per tem No 130 but back ply of table bed side and S&F new back ply 6mm thick complete all as shown on drawing as specified & directed by Engr-in-Charge.

M&L for polishing with two coats of french polish on old and new surfaces including prepration of surfaces of Table bed side complete all as shown on drawing as specified & directed by Engr-in-Charge.

REPAIR TO CHAIR COMPUTER :- S & F in repairs of maintenance free Gas lift for chair computer rest all as shown on drg and as directed by Engr-in-Charge.

S & F in repairs of Padestal assy injection moulded in black 30% glass filled nylon , 50mm MS castor pin is of press fitted to each prong for holding the castor,for chair computer rest all as shown on drg and as directed by Engr-in-Charge.

S & F in repairs of twin wheel castors for chair computer rest all as shown on drawing and as directed by Engr-in-Charge.

S & F in repairs of PU seat & back duly upholstered with best quality Acrylic/polyester febric complete for chair computer rest all as shown on drg and as directed by Engr-in-Charge.

S & F in repairs of handles of chair revolving made of black integeral skin polyurethane reinforced with MS insert scratch proof complete for chair computer with arm rest all as shown on drg and as directed by Engr-in-Charge.

REPAIR TO TABLE COMPUTER :- Removing of existing unserviceable table top for Table computer and S&F new table top of size 900 X 600 mm made out of 18mm thick prelaminated particle board with decorative finish one side and balancing white on the other side of exterior grade duly fixed table frame with suitable screws wood/steel with cup washer and 18x4 mm thick teak wood beading on all round, rest all as shown on drg and as directed by Engr-in-Charge.

Removing of existing unserviceable Key Board tray from Table computer and S&F new Key Board tray of size 450 mm X 480 mm made out of 18mm thick prelaminated particle board with decorative finish one side and balancing white on the other side of exterior grade duly fixed to the existing Telescopic channel, rest all as shown on drg and as directed by Engr-in-Charge.

Removing of existing unserviceable Mouse tray from Table computer and S&F new Mouse tray of size 380 mm X 200 mm made out of 18mm thick prelaminated particle board with decorative finish one side and balancing white on the other side of exterior grade duly fixed to the existing Telescopic channel, rest all as shown on drg and as directed by Engr-in-Charge.

Removing of existing unserviceable damaged drawer from Table computer and S&F new drawer of size 380 mm X 200 mm 75 mm deep made out of 18mm thick prelaminated particle board with decorative finish one side and balancing white on the other side of exterior grade duly fixed to the existing Telescopic channel, rest all as shown on drg and as directed by Engr-in-Charge.

Removing the existing unserviceable Telescopic channel from Table computer and S & F in repairs Telescopic Channel of suitable size for Key board tray/Mouse tray/Drawer of table computer and re-fixing the existing Key board tray/Mouse tray/Drawer with new telescopic channel all as specified on drawing or as directed by Engineer-in-charge.

Removing of existing unserviceable Upper/Bottom shelf from Table computer and S&F new Upper/Bottom shelf of size 450 mm X 300 mm made out of 18mm thick prelaminated particle board with decorative finish one side and balancing white on the other side of exterior grade duly fixed to the frame of Table computer with suitable screws wood/steel with cup washer, rest all as shown on drg and as directed by Engr-in-Charge.

Welding of broken existing Square MS pipe of Table computer duly painted with two coats of synthetic enamel paint over a coat of red oxide primer to match the existing shade complete all as specified & directed by Engr-in-charge.

S & F in repairs Nylon buffers of legs for table computer rest all as shown on drg and as directed by Engr-in-Charge.

Supreme Builders