SPECIAL REPAIR TO ORS MD ACCN OF BLOCK NO. 71 (12 QTRS) AT ZORAWAR ENCLAVE (SF ACCN) IN AYC UNDER AGE (I) AYODHYA CANTT.

Amount

Dismantling brick tiles any size laid bedded and pointed in any mortar, complete all as specified and as directed.

Demolition of mud in roofs any thickness and in any position and leaping over roof terrace ,removing the demolished material to a distance exc 250 m & n exc 500 m and depositing where directed at a level n exc. 1.5 m above starting point, complete all as specified and as directed.

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) in roof padding finishing the surface fair & even, complete all as specified and as directed.

M&L for preparation of newly plastered surface of roof including cleaning the surface by using wire brush/ pressure hose and applying high performance polyurethane liquid membrane roof casting cold applied in two coats @ 1.5 Kg/Sqm applied with spray/brush an elongation of 300% to 700% and tensile strength of not less than 3N/Sqmm as per ASTM D412 and ASTM D2370, crack bridging ability of 3.5 mm as per ASTM C 1305, shore a hardness of not less than 60as ASTM D 2240. The item includes epoxy prime applied @ 0.15 Kg/Sqm and a geotextile of 40 GSM to be applied over first coat while first coat is still wet complete as per manufacturer's instructions and sound engineering practice, complete all as specified and directed.

M&L for screed bed 10 mm thick in cement mortar 1:3 over roof slab finished even & fair, complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed.

M&L for coloured Non - Skid Ceramic tiles 7 to 8 mm thick (400X400 square) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bedding in cement mortar (1:6), complete all as specified and as directed.

M&L for coloured Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bedding in cement mortar (1:6), complete all as specified and as directed.

M&L for coloured Non - Skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in vertical surface, skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed

M&L for coloured Glazed ceramic tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and incl 10mm thick plaster in cement mortar (1:4), complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar, complete all as specified and as directed.

M&L for 15-18 mm thick Granite slab work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in & inclucking 20 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. including rounded/half rounded edge and hole for gas pipe in pre-cast slab as well as stone slab in cooking platform, complete all as specified and as directed. Note:- Rounding of edges shall be measured & seperately under relevent item.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations etc, complete all as specified and as directed.

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) incl chequered tiling and Paver blocks, complete all as specified and as directed.

M&L for 75 mm thick PCC 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) as in plinth protection, finishing cement concrete surface even and fair complete all as specified and directed. Note:- Plinth protection will be laid in outward slope of 1in 12 and in alternative bays/panel.Length of panel shall not exceed 2.5 m and joint between two panel shall be filled with mastic filling comrimising mixture of one part of hot blown bitumen 85/25 penetration and two part of heated sand.

Taking down cement plaster on brick or stone walls or ceiling etc including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work in CM in 1:4 finished even and fair, complete all as specified and as directed.

M&L for rendering 10mm thick in CM (1:6) on Brick/ Conc surface finished even and fair on internal surfaces of wall, complete all as specified and as directed.

M&L for rendering 5 mm thick in CM 1:3 on concrete surface in ceiling, complete all as specified and as directed.

M&L for preparation of new plastered surface and applying two coat of oil bound distemper on walls over a coat of primer incl 1mm thick wall care putty complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coat of oil bound distemper on walls over a coat of primer and 1 mm thick wall care putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and as directed.

M&L for preparation of old surfaces of ceiling/wall and applying two coats of white wash, complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings heads, shoes, bends, swan-necks, etc., incl cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and as directed.

S&F 110mm PVC (SWR) pipes single socketed, excluding fittings in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed.

S&F 75mm PVC (SWR) pipes single socketed, excluding fittings in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall incl necessary clamp etc complete all as specified.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall incl necessary clamp etc, complete all as specified and as directed.

S&F in repair 75mm PVC floor trap plain with grating including jointing with solvent cement, complete all as specified and as directed.

S&F 110mm PVC (SWR) bends with access door, complete all as specified and as directed.

S&F in repair 110mm PVC (SWR) bends any radius, complete all as specified and as directed.

S&F in repair 75mm PVC (SWR) bends any radius, complete all as specified and as directed.

S&F in repair 75mm PVC (SWR) bends any radius with acess door, complete all as specified and as directed.

S&F in repair 110mm PVC (SWR) junction single, (Single T) equal or unequal with acess door, complete all as specified and as directed.

S&F in repair 110mm PVC (SWR) vent cowl, complete all as specified and as directed.

S&F in repair Stack clamps made out of 50mm x 5mm flat iron & 16mm round iron stays including bolts & nuts and securing ends of stays for 100/110mm bore pipe, complete all as specified and as directed.

S&F in repair Stack clamps made out of 75mm x 5mm flat iron & 16mm round iron stays including bolts & nuts and securing ends of stays for 75mm bore pipe, complete all as specified and as directed.

M&L for Cutting chases pinning in making good to facing where reqd. and pointing in CM 1:3 to ends or edges of landing , steps, cills, sunshades,selfs lintels etc. and cutting chases for conceled for water tubing or conceled condute wiring etc and making good, cutting n.exc 10cm girth.complete all as specified & as directed

Taking up or down steel tubing and connection including cleaning for refixing or removal to store 15mm bore pipe, complete all as specified and as directed.

S&F 16 mm outer diameter CPVC Pipes SDR 11 & Plain CPVC SDR 11 fittings on wall/ceiling or laying in floors, complete all as specified and as directed.

Taking up or down steel tubing and connection including cleaning for refixing or removal to store 20mm bore pipe, complete all as specified and as directed.

M&L for 20mm bore GI tubing medium grade with all fittings and fixed complete to walls/ ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

Refixing old steel tubing 20 mm dia and connections in new or old position (Walls, ceiling, floors, etc.), complete all as specified and as directed.

S&F in repair 15 mm size bib taps cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipes, complete all as specified and as directed.

S&F in repair 15 mm size angular cock, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed both end for iron pipes complete all as specified and as directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

S&F in repair Corner glass shelf with brass chromium plated bracket fixed to wall, complete all as specified and directed

S&F in repair Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed.

S&F in repair Sink Mixture, wall mounted with 50 mm long swivel spout connecting legs and wall flanges fixed to iron pipe 15mm bore complete all as specified and directed.

S&F in repair vitreous china wash hand basin white flat back size 550 x 400 mm excluding taps waste chain and plug but including bracket, waste coupling of 32 mm size fixed in repair complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm bore central hole basin mixer with 450mm braided connection pipe (without popup) complete all as specified and directed.

S&F in repair 15 mm bore brass CP wall mixer with provision of overhead shower with 115 mm long bend pipe on upper side, connecting legs and wall flanges for iron pipe and fixed complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 125 mm size and fixed complete all as specified and directed

Supply and fix 500 litre capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete and including dismantling of old RCC tank complete all as specified and directed.

S&F in repair 20 mm dia Gun metal, globe or gate valves,with iron wheel head,screwed both ends for iron pipes and fixed, complete all as specified and as directed.

S&F in repairs, PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S&F 32mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 and fittings, fixed complete to walls, ceilings or in floors etc., complete all as specified and as directed.

S&F in repair Kitchen rack plate of stainless steel of size 75 x 60cm having thickness 01mm as per sample kept with AGE (I) Office, complete all as specified and as directed.

S&F in repair brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges including brackets fixed to wall complete all as specified and directed

S&F in repair brass chromium plated Tumbler holder, complete all as specified and as directed approved by Engr-in-charge. Make:- Jaquar cat part No AKP 35741P or equivalent in makes as specified in PS

S&F in repair SS soap dish complete all as specified and directed Make:- Cera Cat Part No. F5007106 or equivalent in makes as specified.

S&F in repair vitreous china squatting pan, Orissa pattern size 580mm x 440mm with integral foot rest including connection to trap and to flush pipe, anti-syphonage pipe etc complete all as specified and directed.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets of 10 Ltr capacity, complete all as specified and as directed.

Demolition of PCC of any description and in any position not specifically provided for complete all as specified and directed

M&L for Cement concrete 1:5:10 type E2 using 40mm graded crushed stone aggregate as in sunken part of slab, complete all as specified and as directed.

M&L for providing 25 mm thick, cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate in flooring for levelling course for floor tile/sunken slab complete all as specified and as directed.

S&F in repair 25mm dia stainless steel curtain rod of 304 grade for door & windows incl one pair of SS Bracket and steel cover for each rod cut to size and fixed in position complete all as specified and directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) Area not exc 1.5 Sqm each, complete all as specified and as directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) Area exc 1.5 Sqm but n exc 4.00 Sqm each, complete all as specified and as directed.

Dismantling boarding any desccription fixed in any position with nails or any other means complete all as specified and directed

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening, complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, complete all as specified and as directed.

S&F 125x60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate etc complete all as specified and fixed

S&F 105x60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate etc complete all as specified and fixed

M&L for PCC (1:2:4) type B-1, using 20mm graded crushed stone aggregate as in bed block and filling in door frames, complete all as specified and as directed.

S&F 40 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed

S&F for 2nd class hard wood 35mm thick factory made Glazed and skeleton shutters with sash bars, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc., sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), supplied and fitted to chowkats, complete all as specified and as directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and as directed.

S&F 150 mm steel handle complete all as specified as directed.

S&F 200 mm steel tower bolt complete all as specified as directed.

S&F 250mm long steel sliding door bolt with hasp, staple (bolt type) and fixing four nuts and bolt complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one pink primer, complete all as specified and as directed.

S&F 100 mm long butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed

M&L MS Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars and similar work conforming to Fe.290.Gde-E-165, complete all as specified and as directed.

S&F powder coated anodised aluminium window/ventilator shutter sliding type with styles, rails size 40mm x 20mm, frame for chowkat size 30mm x 90mm, fixed glazing, all are made from aluminium anodised section including necessary jointing cleat, glazing clips, rubber packing, anodised aluminium snap beading, screws of suitable size with and including 4mm thick frosted glass /tinned glass etc, complete all as specified and as directed. Note:- (i) Three Nos of track to be provided. (ii) In three tracks, shutter with frosted glass / tinned glass, wire gauge 0.56mm dia inclussived in rate to be quoted by the Contractor. (iii) Thickness of aluminium section shall not be less than 1.00 mm)

S&F 140mm Floor door stopper of aluminium alloy body and tongue, with hard drawn steel spring, complete all as specified and as directed.

S&F 300mm, Mild Steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and as directed.

S&F 18 mm thick PVC board colour fixed with epoxy coated screws, solvent cement/ adhesive to make kitchen cabinet sides, top and bottom and shelves inside the cabinets complete all as specified and directed. (Density - 575 to 600 Kg/CBM), complete all as specified and as directed. Make:- Rajshri plastiwood or equivalent in make as specified in PS.

S&F auto closing hinges 35 mm of 0 crank(KH-001) OR 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete all as specified and directed. Make:- KAFF, Godrej & Hettich.

S&F magnetic catcher of size 20 mm X 50 mm suitable for cupboard shutter complete all as specified and directed

S&F 75 mm dia oval shape brass handle fancy type polished bright finish complete all as specified and directed

M&L for wall mounted foldable study table up of 18 mm thick both side decorated WPC board of size 75x45cm including all necessary fittings fixtures etc, complete all as specified and as directed.

M&L for Chipping of unsound / weak concrete material of 25-50mm average thickness from slabs, beams, columns, chajjas etc with manual chisel and or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc and disposal of debris for all lead and lifts complete all as specified and directed.

M&L for cleaning of rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry complete and then applying antirust bonding coat of Epoxy bonding adhesive @ 2.20 Sqm/Kg of approved adhesive on chipped portion of RCC than and applying Polymer modified mortar (PMM) at any position and any height (upto three storey) Make :- Fosroc and Sika on RCC members (columns, beams, slabs, chajjas etc) 5 mm thick (total thickness) including necessary form work complete all as specified and directed.

M&L for RCC 1:2:4 type B1 using 20mm graded crushed stone aggregrate in cover slab/platform slab for manhole or similar works set in CM 1:6 complete all as specified and directed by Engineer-in-charge. Note :- Reinforcement shall be measured and paid separately.

Demolition and breaking up 150mm dia in bore drain pipes (salt glazed ware, AC or Reinforced concrete) set in cement mortar in any description complete all as specified and directed

M&L for concrete bed to drain pipes of 150 mm dia including packing under and completely surrounding pipes with cincrete after they are laid and tested in cement concrete 1:4:8 type D-2 complete all as apecified and directed

M&L for Reinforced concrete pipes class NP2 of 150 mm dia laid and jointed complete with collars complete all specified and directed

Demolition of Brickwork/Stone masonary built in cement mortar including all quoins,arches,pillars etc but excluding ashlar facings,dressed stonework and precast concrete articles, complete all as specified and as directed.

M&L for Brickwork with sub- class ‘B’ bricks straight or curved on plan exc 6 m mean radius in CM 1:6, complete all as specified and as directed.

S&F for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete, all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of wall and applying two coats of exterior emulsion paint over a coat of not less than 01 mm thick wall care putty and including a coat of exterior wall primer complete all as specified and directed.

M&L for complete removal of existing treatment of old plastered or unplastered surfaces of wall and applying two coats of exterior emulsion paint over a coat of not less than 01 mm thick wall care putty and including a coat of exterior wall primer & complete removal of existing surface complete all as specified and directed. Note:- (i) Exterior primer & acrylic emulsion paint to be applied on wall surface by using Airless spray technology with working pressure of 3300 PSI and capable of operating single spray gun with max material hose length of 30 mtr.The spray machine shouild be of reputed manufacturer with pro gaurd technology and capability of tracking pressure. (ii) Allow 6-8 hrs to dry the surface for painting of subsequent coat

Taking down copper/aluminium point wiring for (light, fan, socket or power) complete including unserviceable fittings such as switches, ceiling rose, holders, sockets,light fittings etc. and making good the disturbed surfaces on wall/floor etc, complete all as specified and directed.

Taking down fans/meter/Geyser/Exhaust fan from existing position and removing the same and deposited to MES store and will installed after completion of work, complete all as specified and directed.

Taking down ols and unserviceable sub main wiring any size/type /core incl earth wire complete with batten conduit etc, complete all as specified and directed.

Taking down old and unsv sheet metal enclousure ,switch fuse unit,distribution board any type/way/capacity including fuses mcbs ,insulator rccbs etc copmlete after removing all connection and amking good the disturbed surface all as directed by Engineer-in-Charge.

M&L for point wiring with two single core PVC insulated & PVC unsheathed FRLS-H multistranded copper conductor cable of size 1.5 sqmm 1100 volt grade in non metallic rigid PVC concelled conduit medium grade 20/25 mm dia with all accessories mounting all the surface of wall/ceiling/roof/etc with suitable size of module metal flush boxes and including modular front cover plate & back plate for mounting modular type switches /socket/fan/ regulator etc including provision of one single core PVC insulated and unsheathed multi stranded copper cable of size 1.5 sqmm 1100 volt grade as earth continuty conductor connected to common earth dolly switch board complete for following:-

One light/fan point controlled by one switch SP 5 Amps, 240 V.

One bell/buzzer point controlled by bell push.

One 3 pin 5 amps switch socket outlet point on independent board.

One 3 pin 5 amps socket point on same board.

All as per the item No. 110 herein before but with 2.5 sqmm conductor for 5 pin 15 Amps switch socket outlet.

All as per item No. 110 above but for one light point controlled by two 2 ways switches.

S&F switch modular type 1 module single pole, one way 5 Amps, complete all as specified and directed.

S&F switch modular type 1 module single pole, one way 15 Amps, complete all as specified and directed.

S&F socket outlet 2 in 1, 5 pin, 15 Amps modular type 2 module, complete all as specified and directed.

S&F socket outlet 5 Amps modular type 2 module, complete all as specified and directed.

All as per item No. 112 Bell push 5 Amps, complete all as specified and directed.

All as per item No. 112 above but 5/6 Amps 2 ways.

M&L ceiling rose,polycarbonate 3 terminal brass with round sheet, isolated body all as specfied and directed.

S&F stepped type electronic fan regulator modular 120 W type 1 module, complete all as specified and directed.

S&F bell wall mounted decorative,ding dong type AC, 230 Volt, single pole, omplete all as specified and directed.

S&F Submain wiring with two single core PVC insulated unsheathed FRLS-H multistrand copper conductor cable of size 04 Sq mm drawn into and including non metallic medium duty rigid concealed PVC condute not less than 25 mm size ISI marked with all fittings / accessories and 04 Sq mm PVC insulated unsheathed FRLS-H multistrand copper conductor cable as continuous earth wire complete.(For AC Point) Note :- For submain wiring: Two run of single core cable and one run of earth wire will be measured as one length and conduit and its accessories is deemed to be included in the unit rate quoted for this items.

S&F Submain wiring with two single core PVC insulated unsheathed FRLS-H multistrand copper conductor cable of size 10Sq mm drawn into and including non metallic heavy duty rigid concealed PVC condute not less than 25 mm size ISI marked ivory colour (Pressfit or similar brand ) with all fittings / accessories and 10Sq mm PVC insulated unsheathed FRLS-H multistrand copper conductor cable as continuous earth wire complete. ( Main DB to SPN DB) Note :- for submain wiring: Two run of single core cable and one run of earth wire will be measured as one length and conduit and its accessories is deemed to be included in the unit rate quoted for this items..

S&F epoxy powder coated Sheet metal enclosure 4 way double door distribution board when MCB to be used TPN 4 way ,415 volt including making good the disturbed surface with cement mortar(1:4) and to match the existing one complete all as specified and directed.

S&F epoxy powder coated Sheet metal enclosure 12 way double door distribution board when MCB to be used SPN 240 volt sheet complete all as specified and directed

S&F MCB TPN 63-100 Amps 415 volt rupturing cap 10 ka "C" series all as specified and directed.

S&F MCB SPN 32 to 40 Amps 240 volt,50 hz,10 KA breaking capacity :C" curved type complete all as specified and directed.

S&F MCB single pole, 6 to 32 Amps, 240 Volts 50 HZ, 10 KA breaking capacity, complete all as specified and directed.

S&F socket outlet 5 pin 20 amp modular type 2 module with suitable size of module metal flux boxes and including modular front cover plate and back plate for mounting modular type switch & socket with one single pole one module MCB of 20 amp including electrical connection all as specified and directed by Engineer-in-Charge.

S&F a holder backlite with 1x9/10 watt LED bulb includig all fixing accessories and making connection with copper conductor all a s specified and directed.

S&F LED light fittings 1x20 watt ,220 voltAC decorative box type with driver holder including 18 watt LED tube light connecting up with 3 core flexible cable copper conductor of suitable size from ceiling rose complete all as specified and directed.

S&F Sleek LED mirror light decorative wall mounted 10 watt rating with diffuser 2ft long twisted flexible copper wire (approx 0.5 mtr long) complete all as specified & approved by EIC.

S&F LED security light 45 watt complete with security light bracket (complete with two set of clamp ,nut and bolt) made out of 40 mm medium grade GI pipe bend to shape and with fixing arrangements duly welded (length of pipe should not be less than 1.2 mtrs) and making conection with using 1.5 sqmm PVC insulated multistranded copper conductor two single core cable complete all as specified and directed.Make :- Havells/Philips/crompton/Bajaj

S&F ceiling fan complete with blade down rod and accessories 230 V,1400 mm sweep air delivery 245 CFM complete with brusheless direct current motors all s specified and directed.

Supply and fixing inverter batten with square profile and polycarbonate chanel lithium ion 1 battery with charging time 8hrs-10hrs and backup time 4 hrs indoor luminiare batten for wall mounted of capacity 20 watt inclding wisted flexible copper wire (approx 0.5 mtr long) complete all as specified & approved by EIC.

S&F LED Light fittings 1x9/1x10 W bulkhead luminaires incl LED driver connecting up with three core flexible copper conductor of suitable size all as specified and directed

M&L for Earthing complete with galvanised steel earth plate electrode 60cm x 60cmx6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including 15 mm bore light grade G.I. protection pipe (upto 7.5 M beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 Nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work, complete all as specified and directed.

disha construction (BID ID -3383279)

M/s R.S. Enterprises (BID ID -3381874)

awashyakta enterprises (BID ID -3383990)

RKT ENGINEER & SONS (BID ID -3383042)

acchyut trading company (BID ID -3381687)