PROVN OF TOILET BLOCK AT D PARK OF FD WKSP AND OTHER SANCTIONED WORKS IN THE AREA OF AGE B/R II UNDER GE PANAGARH

Amount

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavating in trenches , n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts, wells, cesspits ,manhole pier hole etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in in soft/loose soil Note : Manual excavation to be done. During excavation if any damage occured to existing cable any type/ water pipe line, it will be contractor responsibilty to get it repair and make functional by providing jointing kit etc without any extra cost. Contractor has to repair it within 24 hrs so that essential service can not be effected due to such damage.If contractor fails to repair it within 24 hrs penalty @ Rs 500/- will be charged to contractor. In this GE decision will be final, conclusive and binding.

Excavating over areas, n.exc 1.5 m deep and getting out in soft loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in soft/loose soil complete all as specified and directed.

Removing excavated soil n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft loose soil complete all as specified and directed.

M&L for broken stone hardcore of guage n. exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers not exc 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed complete all as specified and directed.

M&L for 300 mm thick Kankar or laterite, ( mix of fly ash, clinker and stone dust in proprtion of 1:3:6 (ie 10% fly ash, 30% clinker and 60% stone dust) spread, rolled and consolidated to gradient and camber required complete all as specified and directed.

M&L for 200mm thick mix of fly ash, clinker & stone dust in the proportion of 1:3:6 (ie 10% fly ash, 30% clinker and 60% stone dust) laying in layers n. exc 30cm hick, watering, ramming and compacted with vibratory/power roller 8 to 12 ton to required camber and gradient complete all as directed by Engineer-in-Charge.

M&L for RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in precast manhole cover slabs set in CM (1:6) complete all as specified and directed.

M&L for PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in Kerb including necessary form work complete all as specified and directed.

M&L for providing PCC(1:3:6) type C2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) as foundation and mass filling complete all as specified and directed.

M&L for cement concrete type D2 1:4:8 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L for RCC (Design mix) M-25, (using 20 mm graded stone aggregate) as in footings foundation beams complete all as speicified and directed.

M&L for Design mix (M-25), using 20 mm graded stone aggregate as in coloums complete all as specified and directed.

M&L for RCC (Design mix) M-25, using 20 mm graded stone aggregate as beam and lintels complete all as speicified and directed.

M&L for Design mix (M-25), using 20 mm graded stone aggregate as in chajja complete all as specified and directed.

M&L for Design mix (M-25), using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns, in roofs and in shelves and the like complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as speicified and directed.

M&L for Mild steel TMT bars 8 mm dia and over as instirrups , cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as speicified and directed.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe 410-W (Gde E-250) quality A complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe-410- W(Gde- E-250) quality-B. complete all as specified and directed.

M&L for steel work in tubular Post/columns including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade ST-240, roof trusses (framed), trussed, purlin, crane gantries, rails, posts and fastening and heavy brackets framing beam, tee, angle, channel or flat section including distance pieces, cleats etc of quality FE-410-W (Gde-250) quality B complete all as specified and directed.

S&F Steel work in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe-410-W(Gde- E-250) quality- B conforming to IS.1161 - 2014, grade St.-240 complete all as specified and directed

M&L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to 18 Mtr height including all necessary scaffolding and safety measures complete all as specified and directed

S&F Factory made steel ventilator with centre hung shutters, dovetailed or welded including pintol hinges, steel handles, etc. as shown with fixed type including one shop coat of red oxide zinc chrome primer complete all as specified.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, rough finished surfaces of concrete, flat

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to coloums complete all as specified and directed.

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to chajjas complete all as specified and directed.

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to sides and sofits of beams and lintels complete all as specified and directed.

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to sofits of slab complete all as specified and directed.

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to side of slab exc 10cm but n.exc 20cm thick complete all as specified and directed.

M&L for brick work with flyash bricks old size straight or curved on plan to any radius exc 6m mean radius build in CM (1:6) complete all as specified and directed.

M&L for brick work with fly ash bricks old size, straight or curved on plan to any radius,in half brick walls built in cement mortar (1:4) complete all as specified and directed.

M&L for 10mm thick in CM 1:6 rendering on brick or concrete surfaces finished even and smooth with integral water proofing compound on wall complete all as specified and directed.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:4), finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar (1:6), complete all as specified and directed.

M&L for rendering 5mm thick on fair faces of ceiling / chajja concrete surfaces in cement mortar (1:3) complete all as specified and directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene asket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed chanically wherever required including cleat angle, luminium snap beading for glazing/ paneling, C.P. brass/ stainless teel screws, all complete as per architectural drawings and the irections of Engr-in-Charge

M&L for 4 mm thick ACP (Aluminium composite panel) of any color fixed in aluminium with screw and tappered clip complete all as specified and directed.

Providing and fixing factory made UPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) (A) Area not exceeding 2.00 sqm each complete all as specified.

S&F factory made UPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of UPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), UPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For UPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted complete all as specified.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet trip of 20mm with stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing.

S&F 100 mm butt hinges medium weight cold rolled mild steel complete all as specified and directed.

S&F aluminium anodised 150 mm barrel tower bolts of extruded section complete all as specified and directed.

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as speicified and directed.

S&F 150 mm long aluminium alloy handles,fabricated type, anodised complete all as speicified and directed.

S&F Sheet glass 4.8 mm thick, ordinary quality & glazing with oil putty in square but n.exc 0.5 sq.m in each pane complete all as specified and as directed.

S&F Sheet glass 4.8 mm thick, ordinary quality & glazing with oil putty in square but exc 0.5 sq.m in each pane complete all as specified and as directed.

S&F 3mm thick figured glass, pin headed type and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F 5 mm thick glass, pin head type and glazing with oil putty in squares exc 0.5 sqm in each pane complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

M&L for 100 mm thick plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) to receive tiles with nominal reinforcement complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 18-20mm thick over cement screed laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab over & including 15 mm thick cement mortar (1:6) screed etc. set and jointed in neat cement slurry and pointed including rubbing & polishing complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate as in hardstanding laid in panels with and including use and waste of formwork and to divide the area in panels and finishing the surface even and fair complete all as specified and directed.

M&L for 100 mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in hardstanding laid in panels with and including use and waste of formwork and to divide the area in panels and finishing the surface even and smooth with out using extra cement complete all as specified and directed.

M&L for cement concrete 75mm thick 1:4:8, Type D-2 (Using 40 mm graded stone aggregates) as in sub base for flooring etc complete all as specified and directed.

M&L for cement concrete type B0 (1:2:4) using 12.5 mm graded stone aggregate 40 mm thick as in floor for receiving screed bed of floor tiling complete all as specified and directed.

M&L for cement concrete type C2 1:3:6 (40mm graded aggregate) 75mm thick as in plinth protection finished even and smooth with out using extra cement complete all as speicified and directed.

M&L cement concrete type B0 (1:2:4) using 12.5 mm graded aggregate 25 mm thick as in floor for receiving screed bed of floor tiling complete all as specified and directed.

M&L for 25 mm thick chequered cement concrete pre-polished tiles of approved size,set ,jointed and pointed using with grey cement and pigment in floors, pavings etc including the setting and jointing in neat cement plaster or slurry 0.3 kg/sqm over 20mm thick screed bed or bedding layer in cement mortar 1:6complete all as specified and directed.

M&L for glazed ceramic colour joint free tiles tiles in verticle surface 350x250x7mm thick set and jointed in neat cement slurry over 10 mm thick 1:4 cement mortar plaster and pointed in coloured cement to match complete all as specified and directed. (Note : Design, shade and pattern of fixing of tiles shall be as directed by Engr-in-charge)

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm in floors laid over 15mm thick 1:6 cement mortar screed bed etc. set and jointed in neat cement slurry and pointed in white of coloured cement to match complete all as specified and directed. (Note : Design, shade and pattern of fixing of tiles shall be as directed by Engr-in-charge)

Forming 65 mm deep x 10 mm wide mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘B’ when thickness of concrete slab is 200mm complete all as specified and directed.

S&F Stop valves 15mm dia CP fency type, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

M&L for steel tubes,15mm dia bore 'medium grade' with all fitting; laid in trenches or wall including all necessary fittings complete all as speicified and directed.

S&F 15mm bore pillar taps cast copper alloy,with capstan heads,chromium plated,screwed down, fancy type high pressure, with or without lettred 'HOT or COLD' with long screwed sunk and fly nuts complete all as specified and directed.

S&F CP Bib taps 15mm dia, with cfancy handle, screwed down, screwed for iron pipe or for brass ferrule, fency type and fixed complete all as specified and directed.

S&F vitreous China wash basin white, flat back,size 580X450 mm including cutting for pinning in ends of brackets,complete all as specified and directed.

S&F Vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe) including urinal spreader of PTMT any colour for fixing with 15mm dia pipe. (Minimum weight 60gms) and including waste pipe complete all as specified and directed.

S&F vitreous China squatting pan, ' Orissa patteren, size 580 x 440 mm white, with integral footrests and PVC (SWR) S or P traps (excluding flushing cisteren and flush pipe) complete all as specified and directed.

S&F in repairs wash down water closet (pedestal pattern) complete white with plastic water closet seat black closed pattern with flat bottom anc cover and mild steel chromium plated or aluminised hinging device and flush pipe of polythelene of low or density or PVC 32mm dia for low level flushing cistern complete all as specified and directed.

S&F Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete in all respect all as specified.

S&F 10 litre capacity two way flash PVC low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size complete all as specified and directed.

S&F PVC connection pipe 15mm size & 600mm long with cromium plated brass coupling on both ends suitable for 15mm bore steel tubing complete all as specified and directed.

S&F Tubular towel rail, 20mm dia, D type, brass chromium plated, 60cm long between flanges complete all as specified and directed.

S&F PVC (SWR) 110mm dia pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

M&L for PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement etc complete complete all as speicified and directed.

M&L for 40 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, finished fair and even without using extra cement from roof surfaces complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces on roof surfaces of concrete surfaces in cement mortar (1:4) with using WPC complete all as specified and directed. (WPC will be measured and paid separately)

M&L for providing water proofing treatment with a layer of APP based polymeric membrane, 3 mm thick (minimum), weighing not less than 3.60 kg/Sqm reinforced with polymer non woven fabric (weighing not less than 160 gm/ Sqm) shall be applied over one coat of cold bituminious primer @ 0.40 ltr/ Sqm ( membrane shall be laid using butane torch and sealing all joints etc, complete all as specified and directed Note: The overlaps shall be of minimum 75 mm on longitudinal direction and 100 mm on transverse direction) complete all as specified and directed.

M&L for one coat of aluminium paint over APP membrane complete all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer on new iron surfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfacecomplete all as specified and directed.

M&L for prepartion of newly plastered ceiling surfaces and applying three coat of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying Two coas of cement based paint over a coat of alkali resistant primer over new surfaces complete all as specified and directed.

M&L for preparation of new surface and apply Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surface complete all as specified and directed

Material & Labour for preparation of new surfaces of plastered walls and applying two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour over and including a coat of primer over and including wall care putty (1.0 mm thick) complete at any height including all necessary scaffolding and safety measures complete all as specified and directed.

M&L for DWCEP (SN8) 180 (OD)/163(ID) mm diameter Pipes for depth of 0.7-1.65 m laid on 150 mm thick bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to excuted and make sewar line funtional complete all as specified and directed.

Cutting into existing manhole for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smoorth finished and reforming benching as required for 150mm internal dia of pipe complete all as specified and as directed.

M&L for (DWC) structured wall polyethlene coupler/elbow 90/elbow 45/ end plug/reducer for piping system with non smooth external annular corrugated and smooth internal surface (Double Wall) for non presure sewage & drainage application pipes of standard length 6m, grade conforming to IS 16098 (part-II:2013) Stiffness Class SN-8 inner dia 150mm(tolerance limit plus& minus 2mm) anti rodent pipes laid in trenches all as specified and directed.

E/M PORTION M&L for concealed point wiring for fan/light point controlled by one way switch complete with 1.5 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red/yellow/blue wires for phases and black wire for neutral),drawn into and including non metalic PVC rigid conduit medium grade of suitable size and conduit accessories fixed on wall, floor, roof etc. and including provision of PVC FRLSH insulated 1.5 sq mm copper conductor for earth continuity (Green Colour) and connected to common earth dolly including sunken in GI terminal box 2.8 mm thick bakelite hylam sheet cover, ISI marked with CM/L no. for mounting switch & sockets for the following:- Note :- Cost of PVC conduit, cutting chases of wal/ceilingl, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

All as per item No 97.00 above but 5 Amp socket out let on same board with other switches complete all as specified and directed.

All as per item No. 97.00 above but One 3 pin 5 Amps socket out let points on independent board

All as per Item No. 97.00 here-in-before but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 4.00 Sqmm for one power point of 3 pin 15 Amps on independent board including FRLSH grade (ISI mark), PVC insulated, unsheathed one run multi-stranded copper conductor of size 4.0 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified.

S&F switch piano flush type, single pole, 5/6 Amps, one way complete all as specified.

S&F socket outlets 2 in 1, 5 pin, 5/6 Amps flush type 230/240 V complete all as specified and as directed

S&F switch socket combination 2 in 1 multipurpose 5 pin, (6 Amps) flush type controlled by one switch complete all as specified.

S&F switch piano flush type, single pole, 16 Amps, one way complete all as specified.

S&F socket outlets 3 pin, 16 Amps flush type 230/240 V complete all as specified and as directed .

S&F for concealed type sub main wiring with two run of 6.00 Sqmm single core PVC FRLS, PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and including through Rigid non-metallic PVC conduit(medium) ISI marked of size 25mm bore with all fittings like tee/Bend/Elbow/Reducer/Bell mouth/Junction / Terminal Boxes etc. and fixing accessories such as coupler, lock nuts, saddles, pipe hook etc. of nominal size 25 mm including one run of 6.00 Sqmm single core PVC FRLS, PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified. Note : (i) Note : 2 runs of line conductor, one run of earth continuity conductor, one run of PVC conduit and one run of cuttinf chases shall be measured as unit length. (ii) Cost of PVC conduit, conductors, cutting chases of wall, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

S&F for concealed type sub main wiring with two run of 4.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and including through Rigid non-metallic PVC conduit(medium) ISI marked of size 25mm bore with all fittings like tee/Bend/Elbow/Reducer/Bell mouth/Junction / Terminal Boxes etc. and fixing accessories such as coupler, lock nuts, saddles, pipe hook etc. of nominal size 25 mm including one run of 4.00 Sqmm single core PVC FRLSH, PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified. Note : (i) Note : 2 runs of line conductor, one run of earth continuity conductor, one run of PVC conduit and one run of cuttinf chases shall be measured as unit length. (ii) Cost of PVC conduit, conductors, cutting chases of wall, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

S&F LED 9/10 Watt tube light fitting mirror intregated type, including LED retrofit tube lamp 9/10 W , LED tube light nominal power 9/10 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 extruded aluminium LED battens life span of minimum 50000 working hours complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting complete all as specified & directed

S&F in repairs LED 20 Watt tube light fitting intregated type, including LED retrofit tube lamp 20 W , LED tube light nominal power 20 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 50000 working hours and LED batten with aluminium housing and polycarbonate diffuser complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting complete all as specified & directed. . Note (i) Make of batten and LED tube lamp should be of same make.

S&F LED security light 25 watt (Min) 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp, Aluminum die cast housing High efficiency long life LED package in integral module with lumen efficacy of 110 lm/W (Min) and viewing angle of 45 degree to ensure better uniformity, electronic LED driver (SMPS based constant current supply) with Output Short-circuit protection, Surge protection & other reliability test as per latest IS. operational voltage of 170 volts to 270 volts, frequency of 50 Hz, protection grade IP 66, IK-08 CRI greater than or equal to 70% , CW available CCT of 5700K/6500K, power factor of minimum 0.95 , life span of minimum 50000 working hours cincluding necessary electrical connections by PVC sheathed copper conductor wire of 3 core x 1.5 Sqmm and necessary fixing arrangement all as specified. Note : (i) The minimum requirement of lumen efficiency, lumen output and power consumption has been specified. However, as per availability, the bidders may opted higher specification with out any extra cost. The quoted rate is deem to be included for that and no extra payment will be made on this account. (ii) The fittings should be marked 'Date of installation" and "Date of Procurement" with marker pen

All as per BOQ Item No 111.00 here-in-before but for 35 watt complete all as specified and as directed

S&F ventilating steel body exhaust fan 300 mm sweep 230 volt AC complete with louver and all accessories including cutting hole of suitable size, making good surface by doing plaster and applying two coat of distemper complete with fixing arrangement to wall connected with twin core twisted flexible copper conductor (23/.0076) of suitable size complete all as specified and as directed

S&F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 amps rated busbar, 2 way Double door enclosure made up of CRCA sheet steel,powder coated, IP 43, IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge

S&F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 amps rated busbar, 4 way Double door enclosure made up of CRCA sheet steel,powder coated, IP 43, IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge

S&F MCB SP 6-32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed.

S&F MCB SPN 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed.

S&F electric water heater, storage type seel boby with copper inner tank and heating element upto 2KW capacity 25 Ltrs, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and as directed.

M&L for earthing complete with Galvanised steel earth plate electrode 600x600x6 mm mm buried directly in ground (Earth pit not less than 2.25m below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI wire of size 4 mm as earth lead by means of bolt, nuts, check nuts and washers of galvanised iron or steel, upto 7.5m length, earth strip protected by and including 15 mm dia GI pipe (light grade) and connected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC (1:3:6) type C1 , Precast RCC (1:2:4) Type B1 cover slab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100 mm C/C both ways with one handle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI Pipe (Medium Grade) for watering, Charcoal and salt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any type of soil and disposal of spoil to a distance n.exc 50 m and necessary testing complete all as shown in Electrical Plate No 3 of SSR Part-I. NOTE : 1. The unit rare includes for protectionh GI pipe of 15mm and watering pipe of 20mm bore including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of GI wire of 4mm including protection pipe, from top of earth plate upto 7.5 meter above/below ground level is deemed to be included in the unit rate. 4. All the joints in GI wire and connectgion with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate

S&F Pipes galvanized, 25 mm bore “Medium grade”, supplied and laid complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement or specified.

S&F gun metal, gate valve, 25 mm dia with iron wheel head, screwed both ends for iron pipe and fix complete all as specified and directed.

S&F ISI marked rotational moulded polyethylene multi- layer water tanks (vertical cylindrical with close top) of 500 litres capacity hoisted and fixed in position including provision of 20 mm /15 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes including dismantling the existing one and removing to store complete all as specified and as directed.

M&L for cutting existing steel tubing for alternation or addition of size 40 to 50 mm dia GI pipe complete all as specified and directed.

S&F of high pressure PTMT float valve with epoxy coated alluminium rod and high density polythelene ball screwed for iron pipe 25 mm dia with fly nut complete all as specified and as directed.

ROY ENTERPRISE (BID ID -3155353)

NATIONAL CONSTRUCTION CO (BID ID -3163924)