Loading
Loading…
Loading…
Tender Value
₹2.9 Cr
EMD Value
₹5.8 L
Closing Date
23 Oct 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
WORKS
14 conditions · 3 needing a document upload
Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees. N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. (For details refer tender documents)
Similar nature of Work means "Execution of building Works".
32 conditions · 2 needing a document upload
The tenderer(s) should submit the BID SECURITY in acceptable form i.e. only through net banking or e-payment gateway or submitted as Bank Guarantee Bond from a Scheduled Nationalized bank of India or as mentioned in the tender documents. The Bank Guarantee Bond shall be as per Annexure- VI(A) and shall be valid for a period of 90 days beyond the bid validity period.( NOTE: For submission of Bid Security in the form of Bank Guarantee, all the procedures mentioned at Para-5 Bid Security (3)(i) to (vii) mentioned in the tender document should invariably be followed.)
Whether History sheet of tenderers (Annexure-2 of Part-II of Tender documents) uploaded duly filled in with supportive documents.
Whether the details of facilities available vis-a-vis the requirements mentioned in STR in a tabular/narrative form if you are not on the approved list of RDSO, if required in the Annexed Document, is submitted.
Whether, EACH PAGE of the copy of documents/certificates in support of credential is self attested/digitally signed by tenderer/authorised representative with signature, stamp & date.
Whether all the documents related "Mandatory Requirement", as applicable and mentioned in the bid documents are enclosed with the tender.
Please submit bank details as per enclosed Annexure-12 of Part - II of Tender Documents or photo copy of a "Cancelled Cheque". (For details refer tender documents)
Please submit Certificate of Familiarisation as per Annexure-1 of Part-II of Tender Documents. (For details refer tender documents)
Please submit required details as required from Annexure 2 to 11 of Part-II of Tender documents duly filled in and signed. Supportive documents/separate sheet are to be submitted, if required. Annex-2: HISTORY SHEET OF THE TENDERER, Annex-3: TECHNICAL EIGIBILITY CRITERIA, Annex-4: DETAILS OF CONSTRUCTIONS MACHINERIES, TOOLS & PLANTS, VEHICLES ETC. AVAILABLE (ON HAND AND PROPOSED TO BE UTILISED, Annex-5: DETAILS OF TECHNICAL AND OTHER PERSONNELS AVAILABLE ON HAND & PROPOSED TO BE ENGAGED. Annex- 6: DETAILS OF WORKS COMPLETED DURING PREVIOUS THREE FINANCAIL YEARS & CURRENT YEAR, Annex-7: DETAILS OF WORKS ON HAND, Annex- 8: DECLARATION REGARDING ASSOCIATION OF RAILWAY OFFICER (S) WITH TENDERER(S), A n n e x - 9 : LIST OF COURT CASES, Annex-10: LIST OF ARBITRATION CASES. Annex- 11: BROAD PLAN FOR EXECUTION OF THIS WORK. (For details refer tender documents)
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / Hindu Undivided Family (HUF)/ Limited Liability Partnership (LLP) etc. If it is NOT mentioned in the submitted tender that tender is being submitted on behalf of a Sole Proprietorship firm/Partnership firm/Joint Venture/Registered Company etc., then the tender shall be treated as having been submitted by the individual who has signed the tender . The tenderer(s) shall enclose the attested copies of the constitution of their concern and copy of PAN card along with the tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. (for details refer tender documents) NOTE: Any document containing PAN number of the tenderer(s) shall also be considered in lieu of PAN card. However, if no document having mention of PAN number is uploaded, offer will be summarily rejected. (For details refer Tender documents)
For all tenders having advertised cost of Rs.10 lakh or above, the contractor shall have to submit the option to take payment from Railways through a letter of credit (LC) arrangement. The tenderer shall affirm having read over and agreed to the terms and conditions of the LC option. The option of taking payment through LC arrangement, once exercised by tenderer at the time of bidding, shall be final and no change shall be permitted, thereafter, during execution of contract. (The tenderer have to submit the option to take payment from Railway through a Letter of Credit arrangement) (For details refer Tender documents)
The list of personnel / organization on hand and proposed to be engaged for the tendered work. Similarly, list of Plant & Machinery available on hand and proposed to be inducted and hired for the tendered work. (For details refer tender documents)
Documents to be submitted as per Clause 14 of GCC-April 2022 in support of (a)Sole Proprietorship firm (b) HUF (c) Partnership Firm (d) Joint Venture (JV) (e) Company registered under Companies Act 2013 (f) LLP (Limited Liability Partnership) (g) Registered Society & Registered Trust. (for details refer tender documents) NOTE: Non submission of above documents will lead to summarily rejection of the offer.
Proposed construction of 12 Nos.of Track Maintainer room cum Tool room under the jurisdiction of ADEN(KDJR)/KUR.
eTender-NorthKUR-171-2026~ECOR
eTender-NorthKUR-171-2026
Open
Works - General
12 Months
Khordha, Odisha
₹0
₹5.8 L
1 Oct 2026
1 Oct 2026
9 Oct 2026
80 items across 3 schedules · ₹2,89,99,705.71 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | All kinds of soil | cum | 1020 | 177.5 | 1,81,050 |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. | cum | 480 | 196 | 94,080 |
| 3 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. | cum | 300 | 700.5 | 2,10,150 |
| 4 | All kinds of soil | cum | 144 | 126.8 | 18,259.2 |
| 5 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | cum | 432 | 2,123.75 | 9,17,460 |
| 6 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 60 | 7,878.5 | 4,72,710 |
| 7 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) | cum | 120 | 7,178.75 | 8,61,450 |
| 8 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) | cum | 120 | 6,812 | 8,17,440 |
| 9 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm | 288 | 392.15 | 1,12,939.2 |
| 10 | Suspended floors, roofs, landings, balconies and access platform | Sqm | 624 | 927.25 | 5,78,604 |
| 11 | Lintels, beams, plinth beams, girders, bressummers and cantilevers | Sqm | 780 | 736.4 | 5,74,392 |
| 12 | Columns, Pillars, Piers, Abutments, Posts and Struts | Sqm | 480 | 961.3 | 4,61,424 |
| 13 | Under 20 cm wide | Metre | 420 | 208.55 | 87,591 |
| 14 | Weather shade, Chajjas, corbels etc., including edges | Sqm | 72 | 951.1 | 68,479.2 |
| 15 | Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). | cum | 24 | 10,585.9 | 2,54,061.6 |
| 16 | Providing, transporting, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). | cum | 12 | 20,355.8 | 2,44,269.6 |
| 17 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg | 21600 | 107.85 | 23,29,560 |
| 18 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg | 21600 | 107.85 | 23,29,560 |
| 19 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 192 | 9,504.75 | 18,24,912 |
| 20 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 192 | 9,860.4 | 18,93,196.8 |
| 21 | Add for using extra cement in the items of design mix over and above the specified cement content therein. | Quintal | 96 | 733.5 | 70,416 |
| 22 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 120 | 7,132.25 | 8,55,870 |
| 23 | Cement mortar 1:6 (1 cement : 6 Coarse sand) | cum | 300 | 8,752.55 | 26,25,765 |
| 24 | Cement mortar 1 : 4 (1 cement : 4 coarse sand) | Sqm | 144 | 1,105.8 | 1,59,235.2 |
| 25 | Fixed to openings /wooden frames with rawl plugs screws etc. | Kg | 2160 | 238.35 | 5,14,836 |
| 26 | 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm ( +/- 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm ( +/- 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm ( +/- 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi- chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm ( +/- 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). | Sqm | 12 | 2,969.25 | 35,631 |
| 27 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg | 6000 | 133.7 | 8,02,200 |
| 28 | Using flats 30x6 mm for diagonal braces and central cross piece | Sqm | 72 | 5,563.75 | 4,00,590 |
| 29 | Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). | Kg | 1680 | 141.7 | 2,38,056 |
| 30 | Hot finished welded type tubes | Kg | 1080 | 194.4 | 2,09,952 |
| 31 | 40 mm thick with 20 mm nominal size stone aggregate | Sqm | 480 | 614.2 | 2,94,816 |
| 32 | 110 mm diameter | Metre | 180 | 377.4 | 67,932 |
| 33 | 0.56 mm, Aluminium Color coated troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000 mm. | Sqm | 216 | 1,176.7 | 2,54,167.2 |
| 34 | Precoated/mill finish aluminium Ridges plain (500- 600mm) | Metre | 36 | 1,066.2 | 38,383.2 |
| 35 | 1:6 (1 cement: 6 fine sand) | Sqm | 2688 | 333.35 | 8,96,044.8 |
| 36 | 1:6 (1 cement: 6 fine sand) | Sqm | 1920 | 383 | 7,35,360 |
| 37 | 1:4 (1 cement: 4 fine sand) | Sqm | 420 | 471.35 | 1,97,967 |
| 38 | 1:3 (1 cement : 3 fine sand) | Sqm | 540 | 300.45 | 1,62,243 |
| 39 | Neat cement punning. | Sqm | 720 | 79.95 | 57,564 |
| 40 | New work (Two or more coats applied @ 3.84 kg/10 sqm) | Sqm | 4800 | 116.9 | 5,61,120 |
| 41 | Two or more coats on new work | Sqm | 540 | 155.9 | 84,186 |
| 42 | Moorum | cum | 240 | 768.25 | 1,84,380 |
| 43 | White Vitreous China Flat back wash basin size 450x 300 mm with single 15mm C.P. brass pillar tap | Each | 12 | 1,513.6 | 18,163.2 |
| 44 | 510x1040 mm bowl depth 250 mm | Each | 12 | 6,945.6 | 83,347.2 |
| 45 | Orissa pattern W.C. pan of size 580x440 mm | Each | 12 | 3,169.05 | 38,028.6 |
| 46 | 32 mm dia | Each | 24 | 119.55 | 2,869.2 |
| 47 | Providing and fixing 100 mm sand cast Iron grating for gully trap. | Each | 24 | 53.25 | 1,278 |
| 48 | Providing and placing in position filters of 40 mm diameter G.I. pipe with brass strainer of approved quality. | Metre | 120 | 960.3 | 1,15,236 |
| 49 | Providing and fixing to filter and lowering to proper levels 40 mm G.I. pipe for tube well including cleaning and priming the tube well. | Metre | 600 | 546 | 3,27,600 |
| 50 | Providing and placing in position hand pump of approved quality for 40 mm diameter G.I. pipe complete with all accessories. | Each | 12 | 1,321.65 | 15,859.8 |
| 51 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 | Each | 12 | 12,770.55 | 1,53,246.6 |
| Schedule total | ₹2,45,33,931.6 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TenderCondition-GCC25.05.2026_1.pdf e tendering condition
ATTACHMENT
DesignMix_1.pdf
ATTACHMENT
Explanatory Notes Ele G for Sch C
ATTACHMENT
SpecialConditionforElectricalG_1.pdf
ATTACHMENT
ScopeofWorkLocation.pdf
ATTACHMENT
TenderCondition-GCC25.05.2026_1.pdf
ATTACHMENT
ExplanatoryNotesforElectGforSchedule-C_1.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .