INTERIOR FIT OUT WORKS IN OFFICE SPACE OF BANK OF MAHARASHTRA AT Block 4, Plate B, Ground Floor, East Kidwai Nagar, New Delhi.

ABSTRACT OF COST

S No DESCRIPTION Cost of DSR Items Cost of Non-DSR Items

2 ELECTRICAL WORKS 981518.00 744024.68

4 FURNITURE 0.00 2280204.00

6 EPABX WORKS 0.00 255000.00

8 AUDIO VISUAL WORKS 0.00 39376.00

10 FIRE FIGHTING 111373.00 41180.00

11 FIRE ALARM AND PA 526724.00 227740.00

TOTAL DSR+Non-DSR 11830190.18

GRAND TOTAL 11830190.18

GRAND TOTAL 11830190.18

1 Digitally signed by AMIT

SINGH 15:50:50 IST

SCHEDULE OF QUANTITIES: CIVIL

S NO DSR NO/ MR DESCRIPTION QUANTITY UNIT RATE

DSR ITEM NON DSR ITEM

1.00 CONCRETE WORK

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto

4.1.8 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) 40.00 Cum 6326.05 253042.00

Total Concrete Work 253042.00 0.00

CEMENT CONCRETE HARDENER : 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm

thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm

thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume,

hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement

slurry, but excluding the cost of nosing of steps etc. complete.

Total CEMENT CONCRETE HARDENER 17118.00 0.00

2.00 BRICK WORK

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth

level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) 70.00 Sqm 1018.05 71263.50

2.02 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 70.00 Sqm 86.45 6051.50

Total Brick Work 77315.00 0.00

3.00 FINISHING WORK

3.01 13.4 12 mm cement plaster of mix :

3.02 13.60 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :

13.60.1 Two or more coats on new work 600.00 Sqm 137.85 82710.00

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth

3.04 13.61 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

13.61.1 Two or more coats on new work 120.00 Sqm 131.45 15774.00

Total Finishing Work 133740.25 0.00

4.00 WATERPROOFING WORK

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the

like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS

2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm

4.01 22.3 cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including 30.00 Sqm 774.25 23227.50

rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7

kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide

and pasted to each other with bitumen @ 1.7 kg/sqm).

Total Water proofing Work 23227.50 0.00

5.00 DOOR,WINDOW & PARTITION

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board

9.21 construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands

and face veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 39.00 Sqm 2015.75 78614.25

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all

area of door shutter to be measured).

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved

quality with necessary screws etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564,

5.04 9.83 embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. 4.00 Each 1025.65 4102.60

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs

5.05 9.53 and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm 64.00 Each 194.35 12438.40

Providing and fixing fixed glass frameless partition with S/S patch fitting: frameless partitions with 12 mm clear toughened glass

of approved make. Patch fittings / wall connecting profiles such as top patch, bottom patch, central connector, corner connector,

5.06 MR side connector, glass to glass connector. The above work complete in all respect as per approved drawings and as per the 21.00 Sqm 4975.00 104475.00

directions of Engineer-incharge. Payment for glass door shall be made under relevant subhead of the BoQ. The rates shall

include the cost of scaffolding, hardware, all tools, etc for working at all levels.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including

providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary

holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper

etc.to be paid separately).

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete

5.08 as per direction of Engineer-in-Charge.

21.12.2 Powder coated minimum thickness 50 micron aluminium tubular handle bar 28.00 Each 563.50 15778.00

GLASS FILM Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to reproduce

Sand-blasting effect on glass with customised designs, thickness of 2 mil (0.05mm) without adhesive & 3 mil (0.8)with adhesive

having minimum tensile strength of 3.5 pound/inch at 73 F(0.6 kg/cm at 23 C). Adhesion after 24hrs of installation should be 4

5.09 MR pounds/inch (0.7 kg/cm) on Acrylic, Glass Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to 15yrs (indoors) 30.00 Sqm 2092.00 62760.00

must be endorsed by makelist. Contractors payment wouldn't be released until & unless he/she produces orginal warranty

certificate from the manufacturer.

Full or half height Storage /Cupboard: P/F of storage unit 600mm deep consisting of double leaf openable shuttered finished

with 1mm thick approved laminate on front faces over 19mm thick board frame on top ,bottom & sides and 6mm thk ply on back

side of cabinet using approved board or equivalant including drawer units,shelves finished colour as per Interior drawings with

5.10 MR necessary hardwares like concealed Hinges, magnetic catcher,locks,handles, knobs complete etc. at all aspects. All internal 20.00 Sqm 9033.00 180660.00

and back sides shall be laminate or enamal paint of approved brand . All exposed surface to be treated with anti termite and fire

reterdant paint before painting work complete etc

Total Door, Window & Glass Partition Work 288011.75 347895.00

6.00 PARTITION WORK

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and

6.01 9.140 fixed on wooden/ steel frame work, complete as per direction of Engineer-in

9.140.1 12mm thick commercial ply conforming to IS : 1328 BWR type 530.00 Sqm 1084.60 574838.00

50MM THK GI FRAME (FOR THK PARTITION): Providing and fixing metal system up to ceiling height, which includes frame

work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 GSM, consisting of Boral U track

52mm wide having equal flanges of 30mm and 0.55mm thick (Base metal thickness) fastened to the floor slab and ceiling soffit

6.02 MR using rawl plugs with screw at 600mm centers, with first & last fixing point at not greater than 50 mm from either end. Boral C 120.00 Sqm 743.00 89160.00

studs 50mm wide having one flange of 34mm, other flange 36mm, lip size 6 mm and 0.55mm thick installed perpendicularly

within the flanges of floor and ceiling channels located directly opposite to each other at not more than 610mm centers. Maintain

5 to 10mm gap between C Stud and web of U Track.

Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling necessary holes

for rawl plug etc. including priming coat complete.

8.27.1 Kiln seasoned and chemically treated hollock wood 1.00 Cum 163814.10 163814.10

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of

frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive),

consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and

ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor

fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and

0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6

mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or

6.04 9.105 metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of framework by 25 mm

long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed

to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two

flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head

screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at

corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification

and direction of engineer in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board

conforming to IS: 2095: part 3 (Board with BIS certification marks)

6.05 13.114 Melamine polishing on wood work (one or more coat). 35.00 Sqm 118.35 4142.25

Total Partition Work 2360679.35 89160.00

7.00 FLOORING WORK

Providing and Fixing of 5+1 mm thick Click-N-Lock tiles with wear layer is of 0.5 mm, Stone Polymer composite and has an

IXPE Cushion backing of 1 mm ,100% Water & Termite proof, Scratch / Fire / UV resistant, a Recyclable Green product

7.01 MR having WEL- LOCK click system with suitable skirting. Classification of abrasion resistance ( Rubbing action of two abrading 8.00 Sqm 3075.00 24600.00

wheels of S-42 Type , load Applied 500 grams, No. of Cycles 4,200).Design as approved by the Engineer/Architect"

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption

less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick

cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm `including grouting the joints with

white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will

be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles

gently and easily.

11.41A.1 Double charge vitrified tile polished finish of size

ALUMINIUM SKIRTING : Supply of 100 mm "DMC" Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural

7.03 MR Finish. Thichness 1.30 to 1.50 mm. Designed to conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and 40.00 Rmt 549.00 21960.00

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer),

of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge,

7.04 8.31 in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with 100.00 Sqm 1063.45 106345.00

grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Total Flooring Work 493283.75 46560.00

8.00 FALSE CEILING WORK

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern.

The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ? 85%,Thermal Conductivity k = 0.052 - 0.057 w/m

K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round

galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000

mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to

form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm

8.01 26.27 long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level

adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls

/partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall

with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all

T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be

carried out as per specifications, drawings and as per directions of the engineer-in-charge.

26.27.2 With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7). 200.00 Sqm 2362.10 472420.00

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power

pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting

of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange

fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with

8.02 12.45 intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5

mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall

be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long

G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm

long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs

at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and

perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush

finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing

compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per

manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with

frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge

but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Total Ceiling Work 609,934.00 0.00

9.00 WALL FINISHES

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density

9.01 9.127 protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive

of approved quality.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms,

vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm

9.02 8.2 thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy

touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

8.2.2 Granite stone slab colour black, Cherry/Ruby red

8.2.2.2 Area of slab over 0.50 sqm 2.00 Sqm 4425.35 8850.70

Providing and fixing of winchester/faro/cairo/contarct/marbella screen roller blind should have sturdy aluminium top tube of

38mm diameter, powder coated bottom bar, with suitable roller clutch mechanism and plastic ball chain. The roller blind fabric

should possess the mentioned specifications: a) Composition – 33.6% Fiberglass, 59.6% Vinyl & 6.8% Polyester b) Openness

factor - 4% c) Fabric thickness – 1.04 mm +-5% & Weight - 646 gsm (± 5%) d) Width - 300 cm e) Color fastness - Grade 6 f)

UV blockage – upto 96% g) Flame retardancy – NFPA 701 h) Anti-fungal / Anti-bacterial – ASTM E 2180 product protection i)

Environmental certification – GREENGUARD Gold certified j) Acoustical value - NRC:0.25, SAA:0.26. Aluminium profile should

have temper WP consisting of alloy 63400 along with anodizing of 10 micron and powder coating of 60 micron. The tensile

strength of profile should be 9.10 Kg/mm square and elongation 18.The control clutch drive unit engineered heavy duty chain

drive pulley operating system consisting of gear clutch housing and locking plug containing minimum 6 ribs and inserted at

minimum of 38mm into roller tube. It is self-lubricating exclusive clutch with safety pins for secure bracket installation and

9.03 MR unlocking pin for quick manual removal. Universal clutch is most convenient for large windows down to the smallest windows. It 65.00 Sqm 2009.00 130585.00

shall be driven by a ball chain pulley with ball chain and can be positioned at right hand or left hand side of the shade. Clutch

gear ratio of 1.75:1 for reduced operating force on larger blinds. Mounting hardware brackets universal brackets including end

plug bracket with lock down retainer device. Brackets finish of powder coated metal installation brackets made of stamped and

hardened steel. Roller tube circular-shaped aluminium tube extruded from alloy 63400 and temper WP. Bottom rail flat-shaped

extruded aluminium from alloy 63400 and temper WP. Ball chain shall be 2mm diameter cord with plastic balls moulded to form

an endless ball chain. It is used for raising or lowering action of the shades. Plastic parts all plastic components are UV-stable

compounds available whit

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50

9.04 12.57 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss 700.00 Sqm 307.35 215145.00

crossing GI wire etc. complete as per directions of Engineer-in-Charge.

Total Wall Finishes Work 535688.20 130585.00

GRAND TOTAL 5406239.80

GRAND TOTAL 5406239.80

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

S NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR ITEM NON DSR ITEM

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface / recessed medium class PVC conduit,

with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS

PVC insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point (without independent switch

etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /

recessed PVC conduit, and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper

conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core

3 1.5 cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC Metre 1380 265.00 365700.00

insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box

4 1.24 including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 186 111.00 20646.00

1.24.5 6 pin 15/16 amp socket outlet Each 18 175.00 3150.00

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding

5 1.26 modular plate as required. Each 20 32.00 640.00

Supplying and fixing following size/module, GI box along with Modular base & cover plate on

6 1.27 existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated

1 1.14 copper conductor, single core cable in surface/ recessed steel conduit as required

1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre 400 146.00 58400.00

1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 150 167.00 25050.00

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 10 200.00 2000.00

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 10 249.00 2490.00

1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 150 543.00 81450.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 10 752.00 7520.00

Supplying and making end termination with brass compression gland and aluminium lugs for

1 9.1 following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV

grade as required.

Supply of following XPLE armourned 1.1 KV grade conforming to I.S.7098/1554Aluminium

2 MR Conductor Cables :

Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor armoured

cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively & ISI marked.

(b) 3.5 C x 50 Sqmm XLPE cable RM 10 400.00 4000.00

(c ) 3.5 C x 35 Sqmm XLPE cable RM 10 312.00 3120.00

1 2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. Each 20 8.00 160.00

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker

2 2.10 suitable for inductive load of following poles in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB

3 2.13 complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, vertical type three pole and neutral, sheet steel, MCB

distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus

bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But

without MCB/RCCB/Isolator)

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual

5 2.14 current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing

MCB DB complete with connections, testing and commissioning etc. as required.

E PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

1 1.24.6 Telephone socket outlet Set 48 119.00 5712.00

1.24.7 TV socket outlet Set 7 119.00 833.00

Supplying and drawing following pair, 0.5 sq.mm FR PVC insulated copper conductor,

1.18 unarmoured telephone cable in the existing surface / recessed steel / PVC conduit as required.

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways along with

MR required suitable number of GI couplers for joining raceways and fixing GI brackets and all

accessories complete in all respect as per the directions of engineer in charge

(a) 300mmx38mm(GI) - 3 compartment metre 7 3001.00 20076.69

3 (b) 225mmx38mm(GI) - 3 compartment metre 18 2500.00 44697.50

Supply, Installation, Testing and Commisioning of Junction boxes for direct access to cables at

the intersection of raceways supplied completely with base and cover plates, height adjustable

junction box 65- 90 mm including all accessories complete in all respect as per the directions of

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

5 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the exisitng metre 105 33.00 3465.00

surface/recessed steel/ PVC conduit as required

Supplying and fixing of following sizes medium class PVC conduit aong with accessories in

1.21 surface/ recess including cutting the wall and making good the same incase of recessed conduit

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and

5.6 providing masonry enclosure with cover plate having locking arrangement and watering pipe of Set 2 11794.00 23588.00

1 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

5.15 required. metre 30 206.00 6180.00

4 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. metre 50 57.00 2850.00

G PANEL BOARDS

1 MR Floor Panels

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and

commissioning the following sheet steel cubicle type panels fabricated from 1.6mm thick CRCA

sheet, dust and vermin proof, indoor type TPN Panels with hinged lockable doors fabricated from

2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC supply with rear access for

cable alley and with segregated bus-bar chamber with tinned aluminium bus bar and including Each 1 71429.00 71429.00

supplying and fixing following switchgears, meters and accessories, inter-connections, bonding to

earth, powder coated painting and marking as specified. Switch boards complete as per

schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as detailed

in the Specifications

Colour: Gray Powder Coated, as per approved sample.

1 nos, 120 Amps 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking

capacity 25 KA (ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 200 Amps capacity with heat shrinkable colored sleeves

and I/C DMC/SMC bus bars supports at required intervals complete for cross section, size

supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB -4 Nos.

(b) 40 Amps, TPN, MCB - 2 nos

Panel complete as above

H SAFETY ITEMS

Providing and fixing MV danger notice plate of 200mm x 150mm made of mild steel, atleast 2 mm

1 2.21 thick, and vitreos enamelled white on both sides and with iscription in single red colour on front Each 1 226.00 226.00

side as required

Providing and fixing HT danger notice plate of 250mm x 200mm made of mild steel, atleast 2 mm

2 2.22 thick, and vitreos enamelled white on both sides and with iscription in single red colour on front Each 1 244.00 244.00

side as required

Havells make PLANO NEO 34W 2X2 Panel led light is suitable for armstrong celling .CRCA

powder coated white after phosphochromate treatment.High efficiency long life LED package in

integral module with System lumen efficacy of >120 lm/W and viewing angle of 120° to ensure

better uniformity.Powered by an independent Isolated, SELV Output electronic LED driver (SMPS

based constant current supply) with Output Short-circuit protection, Surge protection & other

reliability test. CRI >80, Color temperature 5700K, THD <20% and PF >0.95,IP20,IK03.Lumen

output of 3780 lumens.Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45

1 MR DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge no 70 4238.00 296660.00

Protection:3 KV; Protection : Reverse Polarity, Open & Short Circuit. DRIVER SAFETY

REQUIREMENT STANDARDS :IS 15885-2- 13, TEST REPORT TO BE SUBMITTED; PHOTO

BIOLOGICAL SAFETY NORMS: IS 16108, TEST

CERTIFICATE TO BE SUBMITTED; CERTIFICATION: LM 79 FOR LUMINAIRE LM 80 FOR LED

SOURCE. Havells Cat No: PLANO2X2PLR34WLED857S or

equivalent to Philips or Wipro

Supply, Installation, Testing and Commissioing of Recessed downlightwith HPE (High-

Performance Efficiency) with LED (Light Emitting Diode), system power: 12 W, Luminous flux of

luminaire 1320 lm, 110 LM/W system efficacy, Colour temperature of 4000 K, Neutral white, CRI

> 80, 230V constant current driver, 70% of luminous flux after 50,000 operating hours; energy-

efficient LEDs, direct light emission, housing in die-cast aluminium, Polyester powder white

2 MR coloured coat applied over a 5-stage pre-treatment trim, prismatic diffuser for homogenous light no 50 559.00 27950.00

distribution, ZHLS (ZERO HALOGEN LOW SMOKE) wiring, Electronic control gear,

Protection class II, IP 40,

Ø = 175 Installation,

Supply, mm, DA(Ø) Testing

andHCommissioing

= 59 mm of Recessed downlight with LED (Light Emitting

Diode) system power: 8 W, Luminous flux of luminaire 640 lm, Colour temperature of 3000 K,

Warm white, CRI > 80, 230V constant current driver, 70% of luminous flux after 50,000 operating

hours; energy-efficient LED, direct light emission, housing in die-cast aluminium, Polyester

3 MR powder black coloured coat applied over a 5-stage pre-treatment ceiling trim, with reflector, beam no 6 1025.00 6150.00

angle of 11-15°, electronic control gear,

Protection class II, IP 20,

4 MR Supply, Installation, Testing and Commissioing of 1200 mm LED Tubelight batten 20 W no 4 420.00 1680.00

Total of Electrical items 981518.00 744024.68

ABSTRACT OF COST - SANITARY & PLUMBING WORKS

S.NO. DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

S.NO. DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR ITEM NON DSR ITEM

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690

mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting,

of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern

fittings, nuts, bolts and gasket etc complete.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of

approved quality and make, including painting of fittings and brackets, cutting and making good the

2 17.7A walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Each 2 3459.05 6918.10

Brass single hole basin mixer

3 17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm

17.70.2 from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing EACH 2 325.10 650.20

not less than 263 gms

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets

4 17.10 and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good

the walls wherever required :

17.10.1 Kitchen Sink with Drain Board

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings

17.28.2 Flexible pipe

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality)

complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and

7 17.34 Providing and fixing toilet paper holder

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality

conforming to IS : 8931

18.53.1 15 mm nominal bore Each 8 500.35 4002.80

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun)

iron pipes and making good the same with cement concrete 1:3:6 (1 cement: 3 coarse sand: 6

10 18.76 Cutting holes upto 30 X 30 cm in walls including making good the same.

18.76.1 With common burnt clay F.P.S. (non modular) bricks Each 2 362.40 724.80

Making chases upto 7.5 X 7.5 cm in walls including making good and finishing with matching

surface after housing G.I. pipe etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &

cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with

Internal work - Exposed on wall

18.7.2 20mm nominal outer dia pipes metre 10 325.10 3251.00

18.7.3 25mm nominal outer dia pipes metre 5 408.55 2042.75

18.7.4 32mm nominal outer dia pipes metre 5 500.95 2504.75

18.7.5 40mm nominal outer dia pipes metre 1 674.35 674.35

18.7.6 50mm nominal outer dia pipes metre 1 927.00 927.00

S.NO. DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

S.NO. DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &

cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps

Concealed work including cutting chases and making good the walls etc.,

18.8.1 15mm nominal outer dia pipes metre 10 441.15 4411.50

18.8.2 20mm nominal outer dia pipes metre 5 513.75 2568.75

18.8.3 25mm nominal outer dia pipes metre 1 626.05 626.05

18.8.4 32mm nominal outer dia pipes metre 1 712.75 712.75

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards

and weighing not less than 690 gms.

18.51.1 15 mm nominal bore Each 1 708.40 708.40

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for soil,

waste, and vent, Type-B as per IS : 13592 suitable for rubber ring joints, including all neccessary

specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or without doors),

reducers, WC connectors, couplers, expansion joints / bellows, cowels, clamps, rubber rings, clean

outs etc. fixing at wall/ ceiling/ floor level supported by clamp & hangers etc. in concealed / inside

duct / under floor & basement ceiling / external work etc. including chase cutting as required,

excavation and back filling in all kind of soils, suspended from floor under false ceiling or embedding

the pipes laid under floors / building in 75 mm. alround 1:2:4 cement concrete (1 cement : 2 coarse

sand : 4 graded stone aggregate 20 mm nominal size) including cost of shuttering for proper

completion of the work, breaking and making good the walls and floors etc. after pipes have been

duly laid and tested. The rubber ring shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with nuts, washers etc on 50x50x5

mm slotted angle. The cost will include all support arrangements. The work includes commissioning

of all pipes lines as per drawings and specifications and as directed by engg-in-charge at site.

(i) MR 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) metre 20.00 541.00 10820.00

(ii) MR 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) metre 5.00 368.00 1840.00

Providing, fixing, jointing and testing in position ISI marked (IS:4985) UPVC pipes of min 6 Kg/

Sqcm rating with fitting for waste pipe from fixtures to floor trap including reduces, enlarger, socket,

16 MR couplers, bends, tees etc including fixing at wall/ ceiling level supported by clamp & hangers etc.

cutting holes in wall/ floors/ slabs and making good the same with cement concrete 1:2:4 complete

Providing & fixing UPVC Floor trap of self cleansing design with stainless steel grating complete in

Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser each 3 353.00 1059.00

18 MR Providing & fixing 125 mm dia C.P. grating over floor traps. each 3 720.00 2160.00

Providing & fixing of SS Floor Cleanout, round or square with rubber seal and flat round cover with

screws and other required fitting complete as required.

SCHEDULE OF QUANTITIES - FIRE ALARM

SNO. DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

SNO. DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR ITEM NON DSR ITEM

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal

detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS

Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with

rate of rise cum fixed tempreature thermistor complete with base as required.

4 17.2.7 Supplying, installation, testing & commissioning of fault isolator complete with base as required. Each 5 3257.00 16285.00

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder

complete as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as

Supplying, installation, testing & commissioning of addressable manual call point complete as

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3

8 17.3.1 player (including 6 zone button paging station) with seamless integration facility with main fire Each 1 126399.00 126399.00

alarm panel for voice evacuation complete as required

9 17.3.2 Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required. Each 15 952.00 14280.00

Supplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V rms

operating at 240 volt AC supply complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed

11 17.5.2 copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as metre 270 141.00 38070.00

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the

12 17.5.3 existing surface / recessed steel conduit of following pairs, cores and size including connections

and interconnections etc. as required.

13 17.5.3.2 speaker cable Two pair, 2-core, 1.5 sqmm metre 90 85.00 7650.00

Supplying & Fixing of battery operated illiminated "EXIT" signage, with 2hrs power Battery backup

complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with

microphone assembly complete as required.

16 MR Loop Card capacity of 159 detectors For BMS Fire integration Nos 1 100000.00 100000.00

17 MR Interface Card for BMS fire integration Nos 1 45000.00 45000.00

18 MR Supply of repeater panel having 640 character liquid crystal with backlit control 75000.00 75000.00

TOTAL FIRE ALARM WORKS 526724.00 227740.00

Fire Piping, Hydrants, Sprinklers and Accessories

S No AND SPRINKLER DESCRIPTION QTY UNIT RATE TOTAL AMOUNT

S No AND SPRINKLER DESCRIPTION QTY UNIT RATE TOTAL AMOUNT

SYSTEM 2019 / MR

DSR ITEM NON DSR ITEM

Providing, laying, testing & commissioning of 'C' class

heavy duty MS pipe conforming to IS 3589/IS 1239

including Welding, fittings like elbows, tees, flanges,

tapers, nuts bolts, gaskets etc. and fixing the pipe on

the wall/ceiling with suitable clamp/support frame and

painting with two or more coats of synthetic enamel

1 paint of required shade complete as required :

Providing, fixing, testing & commissioning of 15mm dia

21 quartzoid bulb type sprinklers of rating 68 degree

centigrade with required accessories :

21.1 Pendant type 45 Each 484.00 21780.00

Supplying, installation, testing & commissioning of

sprinkler flexible pipe (UL Listed) of stainless steel

complete with 15 NPT on reducer thread with

maximum working pressure of 175 PSI test pressure of

3 25 875 PSI (Burst) with branch line (Inlet) 25mm NPT

male thread to sprinkler head (Outlet) 15mm NPT

female thread with reducer, nipple, 2 side brackets,

center bracket, stockbar of following sizes complete as

Providing and fixing ISI Marked of approved make Fire

MR Extinguishers complete with all accessories as per

manufacturer's specifications.

a) CO2 gas nozzle type - 9 Litre capacity (IS:15683). 2 NOS 12912.00 25824.00

b) Mechanical Foam gas cartridge type. 9 Kg capacity

c) ABC dry powder stored pressure type 6 kg capacity

SCHEDULE OF QUANTITIES: FURNITURE

S.No. PRODUCT DESCRIPTION REFERENCE IMAGES QTY UNITS PRICE AMOUNT

MAIN TABLE -2850 x 1000 x 750 ht., SIDE TABLE - 1800 x 750 x 650 ht., and Back

Stoarge 2100 x 450 x 750 ht.

Main table of size 2850 x 1000 x 750mm made up of 50mm thk. PLPB board with

laminate finish to enhance scratch resistance and having superior edge profile

supported on Gable ends made out of 25 mm PLPB with Pre/Post Laminate.

Modesty panels are in 18mm thk PLPB.

Side table of size 1800x750x650mm made up of 25mm thk. PLPB board with

laminate finish to enhance scratch resistance and having superior edge profile 1 nos 111,976.00 111,976.00

supported on Gable ends made out of 18mm thk mdf boards . Modesty panels are in

18mm thk PLPB laminate finish.

Back Storage Shutters and Pedestal Facia are all in laminate finish. Separate

provision for mounting switches on the wall adjoining the tables shall be made by

customer as the tables do not come with switch mounting facility. Wire routing / wire

management groumets shall be provided on main or side table as specified by

customer as diected by Engineering Incharge.

2 GM 3Seater Sofa

Allen Sofa set With Chrome Legs. Amazing, affordable style arrive in the form of

this easy-care fabric Sofa. Constructed of high performance easy-care upholstery

that is as subtle and it is durable, this couch is alluringly designed with a

contemporary edge. This savvy furnishing features box spring seats that provide for

sturdy comfort and is outfitted with sleek barrel shaped chrome color legs that

elevate the height seating solution providing for a more modern look as diected by

Engineering Incharge..

Fabric Collection: Green | Brown | Blue

Sofa dimensions: 72.5 in. W x 30.5 in. D x 29.5 in. H

MAIN TABLE -2400 x 1050 x 750 ht., SIDE TABLE - 1500 x750x 725ht. &

Main table of size 2400x1050x750mm made up of 36mm thk. PLPB aminate finish to

enhance scratch resistance and having superior edge profile supported on die cast

chrome finished legs of 50X50mm. Modesty panels are in 18mm thk PLPB laminate

Side table of size 1500x750x725mm made up of 25mm thk. PLPB board with

laminate finish to enhance scratch resistance and having superior edge profile

supported on Gable ends made out of 18mm thk mdf boards . Modesty panels are in 1 nos 93,475.00 93,475.00

18mm thk PLPB laminate finish.

In this cabin furniture set all tops, Modesty, and Pedestal Facia are all in laminate

finish. Separate provision for mounting switches on the wall adjoining the tables shall

be made by customer as the tables do not come with switch mounting facility. Wire

routing / wire management groumets shall be provided on main or side table as

specified by customer.

S.No. PRODUCT DESCRIPTION REFERENCE IMAGES QTY UNITS PRICE AMOUNT

MAIN TABLE -2100 x 900 x 750 ht., SIDE TABLE - 1050x750x 750 ht. & BACK

STORAGE 2950X520X750 / PLPB board with laminate finish to enhance scratch

resistance and having superior edge profile supported on Gable ends made out of

25 mm PLPB Laminate. Modesty panels are in 18mm thk PLPB laminate finish. I

Side table of size 1500x500x750mm made up of 25mm thk. PLPB board with

laminate finish to enhance scratch resistance and having superior edge profile

supported on Gable ends made out of 18mm thk mdf boards . Modesty panels are in

18mm thk PLPB laminate finish.

Back storage unit of size2950 x 520 x 750ht mm made up of 18mm thick PLPB

board top with laminate finish & Shutter made of enchance scratch resistance and

having premium lock with wave key technology. Side and back panels are in prelam 2 Nos 82,765.00 165,530.00

particle board with pVC edge bandin. Back panel is in 9mm thik and side panels are

in 18mm thick. In this cabin

furniture set all tops, Modesty, Back Storage Shutters and Pedestal Facia are all in

laminate finish. Separate provision for mounting switches on the wall adjoining the

tables shall be made by customer as the tables do not come with switch mounting

facility. Wire routing / wire management groumets shall be provided on main or side

table as specified by customer as diected by Engineering Incharge..

MAIN TABLE -2100 x 900 x 750 ht., SIDE TABLE - 1050x750x 750 ht. & BACK

STORAGE 2950X520X750 / PLPB board with laminate finish to enhance scratch

resistance and having superior edge profile supported on Gable ends made out of

25 mm PLPB Laminate. Modesty panels are in 18mm thk PLPB laminate finish. I

Side table of size 1500x500x750mm made up of 25mm thk. PLPB board with

laminate finish to enhance scratch resistance and having superior edge profile

supported on Gable ends made out of 18mm thk mdf boards . Modesty panels are in

18mm thk PLPB laminate finish.

Back storage unit of size2950 x 520 x 750ht mm made up of 18mm thick PLPB

board top with laminate finish & Shutter made of enchance scratch resistance and

having premium lock with wave key technology. Side and back panels are in prelam 1 nos 82,765.00 82,765.00

particle board with pVC edge bandin. Back panel is in 9mm thik and side panels are

in 18mm thick. In this cabin

furniture set all tops, Modesty, Back Storage Shutters and Pedestal Facia are all in

laminate finish. Separate provision for mounting switches on the wall adjoining the

tables shall be made by customer as the tables do not come with switch mounting

facility. Wire routing / wire management groumets shall be provided on main or side

table as specified by customer as diected by Engineering Incharge..

DOUBLE SIDED LINEAR WORKSTATION OF SIZE 1250Lx600Dx750/1050HT

WITH GLASS SCREEN

S.No. PRODUCT DESCRIPTION REFERENCE IMAGES QTY UNITS PRICE AMOUNT

TABLE TOP:- Table Top to made up of 25mm thick prelaminated particle board

having all edges machine pressed with 2mm PVC lipping all sides.

UNDER-STRUCTURE:- Table is supported C Type Leg made up of CRCA Pipe

of 50X50MM Thick for Vertcle Member & 40X40MM Thick for Horizontal support

member. Vertical & Horizontal member are connected to each other with

specially designed Dia-casted connectors.

RACEWAY:- Metal Cable tray provided below table top for data and power cable

management with Electrical Leg to carry the wire from Floor. 36 nos 35,873.00 1,291,428.00

FLIPBOX:- Powder Coated Flip Box 450Lx132D Provided on The Table Top

PRIVACY PANEL:- 8mm Thick Sandwich Glass Screen with Dia-Casted bracket.

Screen Size in As Per Site 350H for Above Table as diected by Engineering

combines outstanding ergonomic support with intuitive adjustability to enable each

user to adjust the position of comfort to suit their physique and the task in hand. The

mesh backrest distributes weight to minimize pressure on the spine while reclining,

as well as providing excellent air circulation for thermal comfort as diected by

Engineering Incharge.

Modern executive and conference seating sensibly designed to express a softer,

more residential feeling with contract durability. Bindu combines the comfort and

craft of an upholstered lounge with the performance needs of a work task chair.

Work’s new feel, expressed in a modern classic.

High-back and mid-back options

Synchro-tilt mechanism and flex back

8 Black or polished aluminum caster base 0 nos - -

9 Meeting & Lunch Room Chairs

S.No. PRODUCT DESCRIPTION REFERENCE IMAGES QTY UNITS PRICE AMOUNT

Chic yet simple, this grey office chair offers all the comfort you need for a productive

workday. Its ergonomic design features padded armrests and a comfortably curved

seat. The adjustable base sits on caster wheels that smoothly glide from place to

place. The soft upholstery is brought to life by horizontal stitching for an extra touch

of style.Upholstery: Grey Fabric /Finish: Black/Chrome Dimensions

Seat 19.25"H x 18.5"D as diected by Engineering Incharge.

Lunch Room Table:- Intensive Meeting Table Size : 3750 mm wide x 900 mm

depth x 740 mm height : Modular Conference System for 12 seating (even number)

capacity with rectangular Table Top is made of 36mm thick PLPB Laminated Finish

with 2mm thick PVC edge banding. Understructure is made of SS of 50*50 Sqmm

and Gable Box is made up of 18mm PLPB in Black Colour. The Access flap

provided with the provision for concealed switches. The table is easy to assembly

modules and hardware which gets quickly installed in the final customer destination.

10 Table top Color options are provided As per direction of Engineering incharge. 1 Nos 92,502.00 92,502.00

Confernce Room Table:- Intensive Meeting Table Size : 5250 mm wide x 1500

mm depth x 740 mm height : Modular Conference System for 14 seating (even

number) capacity with rectangular Table Top is made of 36mm thick PLPB

Laminated Finish with 2mm thick PVC edge banding. Understructure is made of SS

of 50*50 Sqmm and Gable Box is made up of 18mm PLPB in Black Colour. The

Access flap provided with the provision for concealed switches. The table is easy to

assembly modules and hardware which gets quickly installed in the final customer

11 destination. Table top Color options are provided As per direction of Engineering 1 Nos 107,107.00 92,502.00

S.No. PRODUCT DESCRIPTION REFERENCE IMAGES QTY UNITS PRICE AMOUNT

Reception Table Providing & Installation of custom made Reception table of size

upto 3000x750x1050

thk. PLPB Board finished in PLPB Board in laminate finish. All edges to be finished

in 2mm thk PVC edge Bandling

as per design. The Recon surfaces to be white Duco painted. A glass top od width

0.2m on SS pegs to be provided

12 above table. One (1) number Drawer pedestal with 3 drawers to be provided under 1 Nos 82,765.00 82,765.00

STORAGE CABINET 1250x450x1200 - Out of 18mm thk PLPB finished using 1mm

laminate, complete with all hinges, drawer glides and hardware from approved make.

All internal surfaces to be

completed using balancing white laminate. Including D-type handles for shutters and

recessed type handles for

drawers. Storage to be of all heights as per design complete and instruction of

13 engineer-in-charge. 5 nos 7303.00 36,515.00

Disussion Room Table The Size of the Table is 600x600 X 750mm Ht with the

Table top of 25mm PLPB with pre/post laminate finish with understrucured of 18mm

thk PLPB Laminated Finish as diected by Engineering Incharge..

S.No. PRODUCT DESCRIPTION REFERENCE IMAGES QTY UNITS PRICE AMOUNT

UFL 2040 Modern executive and conference seating sensibly designed to express a

softer, more residential feeling with contract durability. Bindu combines the comfort

and craft of an upholstered lounge with the performance needs of a work task chair.

Work’s new feel, expressed in a modern classic as diected by Engineering

High-back and mid-back options

Synchro-tilt mechanism and flex back

Black or polished aluminum caster base (photo is only indicative may vary upon

approval from client)

Total Amount 2,280,204.00

Total Amount 2,280,204.00

SCHEDULE OF QUNATITIES: LAN/ EPABX/ CCTV/ AUDIO VISUAL

DSR/ MR LAN Cabling System

Sr. No. Items Descriptions UOM Qty. DSR Rate Rate DSR Amount MR Amount

1.53 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the

existing surface/ recessed Steel/ PVC conduit as required

Supplying, installing, testing and commissioning of I/O Jack should be Category 6,

TIA568B.2-1 – 250MHz, I/O Jack should be for 100 W, 22-24 AWG copper cable shall:

Use insulation displacement connectors (IDC), Information outlet (RJ45 jack) should be

covered under ETL Verification program for compliance with TIA568B.2-1, ETL

certificate to be submitted with offer the I/O jack should be Blue colour for easy port

identification, Operating Life: Minimum 750 insertion cycle

Supplying, installing, testing and commissioning of CAT 6 Patch panel with

transmission performance compliance with the ANSI/TIA/EIA 568C.2 standard. Should

allow for a minimum of 200 re-terminations without signal degradation below standards

compliance limit.Should have self-adhesive, clear label holders and white labels with the

panel Panel should be of 1U height with 24 port pre-loaded IO. IDC: Suitable for 22-26

AWG stranded and solid wire compatible with both 110 & Krone punch down tools,

Operating Life: Minimum 750 insertion cycles support operating Temperature from -20°

Supply , Installtion , Testing and comissioning of Cat6 1Meter patch cords Blue colour

with high quality four pair twisted stranded cable terminated with RJ45 tangle free

modular plugs at both the ends. The Conductor should be 24 AWG, Multi-strands &

Bare Copper Conductor Metal

Supply , Installtion , Testing and comissioning of Cat6 2 Meter patch cords Blue Colour

with high quality four pair twisted stranded cable terminated with RJ45 tangle free

modular plugs at both the ends. The Conductor should be 24 AWG, Multi-strands &

Bare Copper Conductor Metal

Supply , Installtion , Testing and comissioning of Face Plate should be Single Gang

square plate, 86mmx86mm, should have Write on labels, The Faceplates should have

inbuilt shutters which are compatible with any standard colored keystones jacks. The

Faceplates are available in one, two and four port variants.

Supply, Installation, testing and commissioning of 1 U Horizontal Wire Manager 60mm

7 depth (Front Side) Nos 6 780.00 4680.00

TOTAL AMOUNT ACTIVE COMPONENTS : 58800.00 116770.00

TOTAL AMOUNT ACTIVE COMPONENTS : 58800.00 116770.00

Supply, Installation, Testing & Commissioning of Server based IPPBX along with

Main Unit Power Supply

Auto Attendant/IVRs

Voice Mail for all users with email faciliy Music on Hold, Speed Dial

Hunt Group, Call Routing And many more…

1 PRI port with recording facility 50 Analog Extensions through SIP Based

Supply Installation and Commissioning of centralized Operator Console with all

dignostic Software of IP EPABX System Approved Make- NEC/Avaya/Alacatel

Supply Installation, Testing and Commissioning of Analog Speaker Phone with

TOTAL AMOUNT of EPABX SYSTEM : 0.00 255000.00

TOTAL AMOUNT of EPABX SYSTEM : 0.00 255000.00

Audio-Visual System

Supply ,installation ,testing and commissioning of Cable Management System Cable

Cubby , Black, Hydraulic open & close system, 2 x Universal Power ,2 x RJ45 Network,

1 x VGA, 1 x 3.5mm Audio, 1 x HDMI, 1 x USB Charger Sockets complete with

standard accessories as required.

Cable & Accessories

2 Moulded HDMI cable 10 Mtr. Each 2 6600.00 13200.00

3 Moulded HDMI cable 2 Mtr. Each 2 1088.00 2176.00

Total Amount of AV System : 0.00 39376.00

Total Amount of AV System : 0.00 39376.00

SCHEDULE OF QUANTITIES - HVAC WORKS

S.NO. DESCRIPTION UNIT QTY RATE TOTAL AMOUNT TOTAL AMOUNT

S.NO. DESCRIPTION UNIT QTY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

Supply, installation, testing and commissioning of Inverter type High Wall Indoor and drain pump

1 MR Unit including copper piping upto 10 meters

a MR High Wall - 1 Tr (Inverter Compressor)-5 star Nos 2 40705.00 81410.00

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and

return air path as and where required of required sizes i/c control wiring,the damper shall be

motorized and spring return so as to close the damper in the event of power failure automatically

2 16.20 and open the same in case of power being restored. The spring return action shall be inbuilt

mechanism and not externally mounted. The damper shall also be closed in the event of fire signal

complete as required and as per specifications.

3 GI Gravity Louver

Supply, installation, testing and commissioning of GI Gravity Louver complete with neoperene 30340.00

rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

4 VOLUME CONTROL DAMPER

Supply, installation, testing and commissioning of 50 micron powder coated "Aluminium"collar 27116.00

volume control dampers with key operated of black painted in supply air registers / terminals.

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal

rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers,

vanes, hangers, supports etc. as per approved drawings and specifications of following sheet

thickness complete as required.

a 16.12.1.1 Thickness 0.63 mm sheet SQM 70 983.00 68810.00

b 16.12.1.2 Thickness 0.80 mm sheet SQM 50 1154.00 57700.00

c 16.12.1.3 Thickness 1.00 mm sheet SQM 5 1273.00 6365.00

d 16.12.1.4 Thickness 1.25 mm sheet SQM 5 1677.00 8385.00

6 Diffusers & Grills

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume 127200.00

control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without 82605.00

volume control dampers complete as required

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with 170445.00

aluminium volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without 113385.00

volume control dampers with anti smudge ring & removable core.

S.NO. DESCRIPTION UNIT QTY RATE TOTAL AMOUNT TOTAL AMOUNT

S.NO. DESCRIPTION UNIT QTY RATE TOTAL AMOUNT TOTAL AMOUNT

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell

Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile

rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber

tape insulation complete as per specifications and as required.

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded

glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600

a 16.21 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated SQM 2 647.00 1294.00

aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX

compound etc. complete as required and as per specifications

Supply,Installation charges of fire retardant flexible Canvas Connection between Indoor Units and 19404.00

b MR Ducts and Filters for Ducted Units

DISMANTLING, LIFTING, SHIFTING & REINSTALLING OF EXISTING SYSTEM

Supply Installation, Testing and Commissioning of Inline fan suitable for following capacities

complete with sheet metal casing , electric motor and direct driven centrifugal fan suitable for

operation on 415 +/-10% V,50 Hz , 3 phase or 240 +/- 10% V,50 Hz, 1 phasefitted with speed

a MR regulator in case of single phase including provision of 15 Amp plug and wiring between the fan

and the socket and accessories like flexible connectors , gravity louvers , wire guard & bird screen

etc.The fans shall be acoustically insulated from inside to reduce the db levels. All the fans used

for purging of FM 200 shall be fitted with fire dampers which shall be charged as per item no 2.13.

150 CFM,20 MM STATIC PRESSURE Nos 2 5741.00 11482.00

TOTAL HVAC WORKS ₹ 784755.00 ₹ 169752.00