PROVN OF GUARD ROOM WITH TOILET BLOCK IN UNIT AREA, RAIN WATER HARVESTING FOR SECURITY WALL IN ITARANA CANTT AND SPL REPAIR TO CONVERSION OF LT OH LINE TO LT UG CONNECTED SERVICES IN JP LINE AT ALWAR

Amount

Excavation in trenches not exceeding 1.50m wide and not exc 1.50m in depth and getting out in soft / loose soil complete all as specified and as directed.

All as per item No 1.00 here in above but depth exc 1.5 m but n exc 3m in depth and getting out in soft / loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

Removing surplus excavated soil to a distance n.exc 50 metre and n exc 100 metre and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed.

M&L PCC (1:4:8) type D-2, (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

M&L moorum/red bajri filling in floors or pavings, laid in layers n exc 15 cm thick, spread, levelled and rammed including watering all as specified and directed.

M&L hard core of broken stone or boulders of gauge n.exc 63mm deposited spread and levelled in layers n.exc 15 cm thick watered and rolled/ rammed to a true surface complete all as specified and directed.

M&L RCC work M-25 Design Mix (using 20mm graded crushed stone aggregate) as in foundation including, raft, plinth beam bases for column etc basement slabs under ramed piles and mass concrete complete all as specified and as directed.

M&L RCC work M-25 Design Mix (using 20mm graded crushed stone aggregate) as in columns, pillars, piers posts and struts complete all as specified and as directed.

M&L RCC work M-25 Design Mix (using 20mm graded crushed stone aggregate) as in beams, cantilevers bressumers, lintel over 1.5 mtr span complete all as specified and as directed.

M&L RCC work M-25 Design Mix (using 20mm graded crushed stone aggregate) as in slab supported on walls cantilevers etc complete all as specified and directed.

M&L RCC work M-25 design mix (using 20mm graded crushed stone aggregate) as in chajjas and the likes complete all as specified and directed.

M&L TMT bars, 10mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for column, hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per ser item No 13.00 above but 6mm to 8mm dia.

All as per ser item No 13.00 above but 5mm to 10mm dia as in stirrups, spacers binders reinforcement complete all as specified and directed.

M&L form work to side of concrete foundation, footing, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter complete all as specified and as directed.

M&L form work to side of pillar, posts, struts, piers, columns etc complete all as specified and as directed.

M&L form work to sides and soffits of floor or roof beam, beam hauching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc complete all as specified and as directed.

M&L form work as in suspended slab, such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

M&L form work to chullaah hoods, chajjas, troughs and similar items including edges complete all as specified and as directed.

Treating the bottom and side of excavation at the rate 5 ltr/sqm emulsion of surface area complete all as specified and as directed.

Treating the backfil in contact with foundation at the rate of 7.5ltr/sqm emulsion of surface area complete all as specified and as directed.

Treating the bottom surface of floor at the rate 5 ltr/sqm emulsion of surface area complete all as specified and as directed.

Treating the soil under plinth protection at the rate of 5 Ltr /Sqm emulsiom of surface area complete all as specified and as directed.

M&L 15mm thick screed bed on fair faces of concrete/ brick surfaces in CM 1:4 with water proofing compound @ 3 % of wt of cement finished even and smooth in order to maintain proper slope over existing roof surfaces for laying APP based polymeric membrane finished complete all as specified. (Polymeric membrane and WPC shall be meausred and paid seperately here-in-after).

Supply only integral water proofing compound.

M&L water proofing treatement to RCC roof slab including parapet comprising of following course of treatement/ specified from bottom to top (a) Applying Bituminous primer @ 0.40 Ltr per sqm over plastered surfaces of roof including parapet surfaces. NOTE : Bituminous primer shall be manufactured by M/S STP Ltd or 'EMW FLATE' M/S Texas India Ltd (b) Over the priming coat laying one layer APP based polymeric membrane of approved manufacturer, 3 mm thick weight not less 3.6 Kgs/Sqm reinforced with non woven polyester fabric weight not less than 150 gms per sqm polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flushing.

M&L two coat of reflective silver aluminium paint over APP membrane complete all as specified and as directed.

M&L providing precast cement concrete (1:2:4) type B1, using 20mm graded crushed stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapits and railings upto 60cm in height, copings kneelers, apex stones, bed plates, kerbs not provided for in SSR item No 04028 water throughs and the like including weathering slightly rounded or chamfered angles and throating as directed.

M&L brick work with fly ash brick straight or curved on plan exc 6m mean radius built cement mortar 1:6 complete all as specified and as directed

M&L brick work with sub class 'B' brick straight or curved on plan exc 6m mean radius built cement mortar 1:4 complete all as specified and as directed

M&L brick work with sub class 'B' brick straight or curved on plan exc 6m mean radius built cement mortar 1:4 complete all as specified and as directed

M&L brick work with fly ash brick straight or curved on plan exc 6m mean radius built cement mortar 1:4 complete all as specified and as directed

M&L brick work with sub class B bricks in one brick thick honeycomb walling built in CM 1:4 complete all as specified and as directed

M&L 15mm thick rendering in cement mortar 1:4 mixed with water proofing compound finished with even and smooth mixed with Liquid Water Proofing admixture complete all as specified and directed. (Note : WPA shall be measured and paid separately under relevant item).

M&L rendering 10mm thick internal surfaces in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and fair without using extra cement all as specified and as directed.

M&L rendering 10mm thick internal surfaces in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even and fair without using extra cement all as specified and as directed.

M&L rendering 5 mm thick in CM 1:3 on concrete ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 5 mm thick in CM 1:3 on concrete surfaces such as beams, column etc finished even and smooth without using extra cement complete all as specified and directed.

M&L preparation of newly plastered surface of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of 1 mm thick wall care putty of approved tint complete all as specified & directed.

M&L preparation of newly plastered surface of ceiling applying three coats of white wash complete all as specified and directed

S&F anodized aluminium frame and other sections for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc complete all as specified & as directed.

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No) complete all as specified & as directed.

S&F powder coated of any colour as approved anodised aluminium grill of approved pattern for windows/ ventilators/doors complete all as specified and directed.

S&F 4.80mm thick sheet glass ordinary quality, in squares n.exc 0.5 Sqm each complete as directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples to wooden /steel frames with beading complete all as specified & directed.

S&F frame work such as grills, grating etc,with ends of bars shouldered &/or riveted or forged into spikes,framed guard bars, barred iron door ladder, door frame, cooler stand, balusters,walk ways, railing,frame work or water tanks & similar work conforming to Fe-290 Gde E-165.

S&F factory made 30mm thick flush shutter, solid core construction, with block board core and plywood face panels both face covered with decorative face veneer with lipping/frame to match commercial type on both sides with self closing circular knob for locking arrangements complete all as specified & directed.

M&L factory made 2nd class glazed and skeleton door shutter made out of stiles & rails of 30mm thick 2nd class hard wood, klin seasoned and chemically pressure treated & open reabted and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain, chamfered of rounded, fitted with and mitred beads for securing glass etc compelte, the size of members of shutter shall be as per IS-1003. The shutter shall be fitted to the chowkhats complete all as directed.

S&F preparation of new steel surface of any description over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L preparation of newly wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (of approved shade) over a coat of pink primer all as specified and directed.

M&L 75mm thick PCC 1:4:8 type D2 (using 40mm graded aggregate) as in floor sub base pavings etc complete all as specified and directed.

M&L PCC 25mm thick 1:2:4 type B0 (using 12.5mm graded aggregate) as in floor as in levelling course complete all as specified and as directed.

M&L vitrified ceramic tiles 10mm thick (square/ rectangular), polished, coloured (light shade as approved) area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over with and including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L vitrified ceramic tiles 10mm thick (square/ rectangular), polished, coloured (light shade as approved) area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over with and including 10mm thick cement plaser in CM 1:4 complete all as specified and as directed.

M&L non skid ceramic tiles (coloured) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but n exc 0.18 in floors etc laid over with and including 15mm thick screed bed or bedding layer in CM 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L glazed coloured ceramic tiles in vertical surface 300mm x 450mm x 7mm thick laid over with and including 10mm thick rendering in CM 1:4 and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L 75mm thick cement concrete 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in plinth protection path laid in panel surface finished even and fair using extra cement complete all as specified and as directed.

M&L 100mm thick cement concrete 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in flooring and finished even and fair complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutters 28 to 30mm thick (stiles), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front Face & 2mm Plan colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S&F extruded aluminium alloy with galvanised mild steel hing pin butt hinges 100mm long complete all as specified and as directed.

S&F aluminium anodised, barrel tower bolts of extruded section and fixed 150 mm long complete all as specified and as directed.

S&F extruded aluminium alloy handles 150mm size fabricated type anodized ISI marked complete all as specified and as directed.

S&F mild steel butt hinges medium weight cold rolled of size 100mm, ISI marked complete all as specified and directed.

S&F aluminium alloy anodised sliding door bolt with hasp,staple (bolt type) 300mm long not less than 12mm dia with and incl minimum of 06 bolts and nuts, 4 on plate and 2 on staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, plate and fixed all as specified.

S&F 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F vitreous china squatting pan of Orrisa pattern size 580mm x 440mm white with integral foot rest (excluding flushing cistern and flush pipe complete incluidng provision of lime concrete bedding complete all as specified and directed.

S&F PVC flushing cistern low level 10 ltr capacity with inlet ball valve float and handle syphonic action type including brackets and flush pipe of polythene of low or high density ISI marked complete all as specified and as directed.

S&F tubes medium grade 'galvanised' with and including all fitting and fixed bore of 20 mm dia complete to walls and ceiling or laid in floor complete all as specified and as directed.

S&F tubes medium grade 'galvanised' with and including all fitting and fixed bore of 15mm dia complete to walls and ceiling or laid in floors of 15mm bore complete all as specified and as directed.

S&F 15mm dia stop valve/angle valve of copper alloy fancy type chromium plated screwed down high pressure with crutch or butter fly handle screwed on both ends for iron pipe or for union complete all as specified and as directed.

S&F 15 mm bore fancy type long body bib tap, half turn, with wall flange, cast copper alloy with capstan heads, chromium plated, screwed for iron pipe or for brass ferrule, complete all as specified & as directed.

S&F swivel shower rose(fancy type) chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union all as specified and directed.

S&F vitreous china urinal half stall type white excluding flushing cistern, but including PTMT urinal spreader and waste pipe complete all as specified and directed.

S&F WHB flat back of size 580mm x 450mm excluding taps waste chain plug stopper but incl brackets incl waste pipe cutting pinning in ends of brackets complete.

S&F 15mm dia bore cast copper alloy chromium plated fancy type pillar tap for with out cold & hot water complete all specified and as directed .

S&F 1000 Ltr capacity of rotational moulded polyethylen water storage tank (Cylindrical vertical with closed tap) hoisted and fixed in position including GI pipe medium grade washout pipe 450mm long with plug and 20mm dia GI pipe medium grade overflow pipe 600 mm long with fitting complete all as specified and as directed.

S&F ball valve brass high pressure with polythene float and fly nut screwed on iron pipe ad fixed 20 mm bore of pipe.

S&F PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S&F 20mm bore Gun Metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

S&F PVC (SWR) pipes of 75 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.8 mm) single socketed in any length with rubber ring joints laid in trenches or in floors of 75mm pipe complete all as specified and as directed.

S&F PVC (SWR) pipes of 110 mm bore single socketed in any length fixed to wall complete all as specified and as directed.

S&F PVC (SWR) floor trap, plain with grating including joining with solvent cement 75 mm dia complete all as specified and as directed.

S&F PVC (SWR) bend 75mm bore of any radius complete all as specified and as directed.

S&F PVC (SWR) bend 110 mm bore of any radius complete all as specified and as directed.

S&F PVC (SWR) 110mm Branch piece (single Y) equal or unequal complete all as specified and as directed.

S&F PVC (SWR) 110/75mm bore Vent Cowl complete all as specified and as directed.

M&L machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade and fixed with grey cement and pigment laid over with and including 25mm thick sand cushion complete all as specified and directed.

M&L precast (factory made) cement concrete kerb stone casted PCC 1:2:4 type B-1 using (20 mm graded stone aggregates) with plain or interlocking joints as solid blocks exc 10cm in width and setting and jointed in CM 1:6 complete all as specified & directed.

M&L reinforced concrete pipes, class NP-2, ISI marked, laid to slope in trenches, jointed and tested complete with collars for 150 mm bore pipes complete all as specified & directed.

M&L PCC (1:4:8) type C-2, (using 40 mm graded stone aggregate) as in bedding to drain pipes, including packing under and haunching against the sides of pipes tested complete for 150 mm bore concrete pipe complete all as specified & directed.

M&L PCC (1:3:6) type C-1, (using 20mm graded stone aggregate) as in coping, manholes etc complete all as specified & directed.

M&L cement concrete (1:2:4) type B-1, (using 20mm graded stone aggregate) as in surface channels of drains and benching including finishing the top of benching even and smooth using extra cement complete all as specified & directed.

M&L precast reinforced cement concrete M-20 (Nominal mix using cement content 360 kg/cubic metre) using 20mm graded stone aggregate for manhole/soakage well cover including placing in position and set in CM (1:4) including necessary form work.

M&L hard core of brick of gauge n.exc 63mm deposited spread and levelled in layers n.exc 15cm thick watered and rolled/ rammed to a true surface complete all as specified and directed.

M&L loose filling of broken bricks of gauge 80 to 150mm in soakage pits, soakage well complete all as specified and directed.

M&L cutting and inserting tee, L bow, bend/collar and tapping the connection from existing 80/50mm DI/GI tubing line for taking branch connections including tapping accessories complete all as specified and directed.

Excavation in over areas n.exc 1.50m in depth and getting out in soft / loose soil .

All as per item No 102.00 above but depth exc 1.50m but n.exc 3m.

All as per item No 102.00 above but depth exc 3m but n.exc 4.5m.

All as per item No 102.00 above but depth exc 4.50m and n.exc 6.00m.

M&L boring holes in soft/loose soil for encasing GI tubing 300mm pipe etc complete all as as specified and directed

S&F 150 mm GI slotted pipe with 3.16mm slot size pipe for inserting in hole etc complete all as as specified and directed

Hardcore of guage exc 63mm but n exc 100mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rolled/rammed to a true surface omplete all as as specified and directed.

S&F GI pipe cap of 150mm bore complete all as as specified and directed.

M&L loose filling with gravel of size 3.0mm to 6.0mm to be filled around slotted pipe complete complete all as as specified and directed.

M&L gravel bed for loose filling of size 6.0mm to 9.0mm complete all as as specified and directed.

M&L gravel bed for loose filling of size 3.0mm to 4.0mm complete all as as specified and directed.

M&L gravel bed for loose filling of size 1.0mm to 2.0mm complete all as as specified and directed.

M&L Jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in lime mortar 1:3 or CM 1:6 omplete all as as specified and directed.

M&L providing cement concrete 1:2:4 type B-2 concrete, (using 40mm graded stone aggregate) as in water troughs, surface channels and drains and benching including finishing the top of benching even and smooth using extra cement complete all as directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds mitred/stopped, end etc complete all as directed.

M&L point wiring complete with 1.5 Sqmm single core multistranded copper conductor fire resistant low smoke & heat (FRLS) PVC insulated and unsheathed cable 1100 Volts grade confirming to IS-694 drawn through non metallic rigid PVC heavy duty conduit in concealed (min 20mm external dia) but shall be increased as per actual site requirement in accordance with clause No 19.125 of SSR Part-I, ISI marked with wall thickness not less than 1.8mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling including 1.5 mm FRLS PVC insulated unsheathed copper earth wire including sunken type pressed steel terminal boxes electro plated of suitable size with bakellite white/coloured top sheet cover 3.0mm thick for one light point controlled by one way switch all as specified & directed. Note : The quoted rate shall be incuded cutting, chasing, making good of distrub surfaces including matching of existing colour surface of walls.

All as per serial item No 117.00 here-in-before but for one fan /exhaust fan point controlled by one switch and regulator.

All as per serial item No 117.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per serial item No 117.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per serial item No 117.00 here-in-before but for one 3 pin socket outlet 15/16 Amps controlled by one 15/16 Amps switch on independent board with 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

S&F switch piano flush type, single pole, one way, 5/6 Amp, 230 Volts complete all as specified and directed.

S&F switch piano flush type, single pole, one way, 15 Amp, 230 Volts complete all as specified and directed.

S&F socket outlet for 3 pin (with 2 pin outlet also), 5/6 Amp, flush type 240 volt complete all as specified and directed.

S&F socket outlet for 2 in 1, 3 pin 5 & 15 Amp, flush type 240 volt complete all as specified and directed.

S&F ceiling rose surface bakelite 65 x 50mm two or three terminals complete all as specified and directed.

S&F decorative ultra slim liner LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient suitable for 16 Watt to 20 Watt with LED tube of model E-LITE LED Pride Plus and connecting up with and including three core, PVC insulated, sheathed copper conductore cable of required size and length from ceiling rose to fitting complete all as specified & directed. Havells Cat Part No LHEXBLP7PN1W018 or equivalent of Surya/Philips/Crompton Greaves.

S&F sheet metal enclosures, double door type, suitable for fixing MCB SPN with 200 Amps rated bus bar, 8 way, 240 volts complete all as specified and directed.

S&F MCB 32 Amps, single pole & neutral, 240 Volts, 'C' curve, 10KA, ISI marked as per IS/IEC 60898-1 2002, Ingerted label holder, sliding bottom clamp improved air channels, colorb coded On/Off indication on dolly IP 20 protected terminals, DC-80V per Pole-1KA complete all as specified and directed.

S&F MCB 6-32 Amps, single pole, 240 Volts, 'C' curve, 10KA, ISI marked as per IS/IEC 60898-1 2002, Ingerted label holder, sliding bottom clamp improved air channels, colorb coded On/Off indication on dolly IP 20 protected terminals, DC-80V per Pole-1KA complete all as specified and directed.

S&F 2nd class hard wood rectangular block open recessed of size 30 x 25 x 5cm depth with 3mm thick phenolic laminated sheet top cover fixed with suitable steel screws & PVC rawl plug (4 Nos), complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated, armoured, heavy duty LT underground electric cable with stranded aluminium conductor 1100 volts grade cross sectional area 10 sqmm 2 core laid in trenches, along poles through pipes etc complete all as specified & as directed. (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately including taking down old unserviceable XLPE cable. (ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.

M&L brick work with fly ash bricks {As per IS-13757 (1993) burnt clay fly ash building bricks}, (Old size bricks) with width equal to the length of the brick laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection complete all as specified & directed.

M&L dry sand (tibba sand) and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

M&L 40mm grade GI pipe (light grade) for protection of LT cable fixed to wall /pole /road crossing including clamps complete all as directed.

M&L earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5m deep below normal ground level and connected to and including galvanized iron earth wire 4mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/test point/ panel/ equipment and testing on including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25mm x 3mm bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & as directed.

S&F ceiling fan 5 star rating 1200mm sweep 240V AC including provision of hook in ceiling of suitable size and necessary electric connection complete all as directed. Make : Havells/Crompton/Bajaj/Orient.

S&F LED type street DRACO Series light luminaire 20 watt 230 V 50 Hz including all necessary fitting accessories and LED complete, all as specified & directed. Make : C&S Cat Part No LTESS20WLED or equivalent of Crompton Greaves / Wipro as approved by GE.

S&F exhaust fan 300mm sweep 240V AC including provision of hole in wall of suitable size for fixing of exhaust fan and necessary electric connection complete all as directed. Make : Havells/Crompton/Bajaj/Orient.

Supply & installation desert cooler in steel body with tank capacity of 120 Ltr, propeller type cooler fan with motor (ISI Marked) three speed 1440 RPM, 1/8 HP Copper winding, 230V, 50HZ, sealed double ball bearing, vacuum impregnated strator winding, One Year Warranty, silent operation, nominal capacity 5000 cum/hr, fan size 450mm, type of blade metallic (HIP), submersible water pump, filter pad, electric driven, single phase, 230 volts, 50 Hz, capacitor 4 mfd, suitable plug top 5/15 Amp including all accessories complete all as specified & directed by Engr-in-Charge. Make : Bajaj/ Khaitan / Crompton. Note :- (i) Filter panels, front grill and top of the cooler body shall be made of 1mm galvanized steel sheet. The sump tank and rest of the body shall be made of 1.20mm thick galvanized steel sheet. The galvanised steel sheet shall be ISI marked and shall have zinc coating not less than 100 gms/sqm and shall conform to IS : 277. (ii) All internal surface including inside of the tank, fan blades, motor body, pump, pump body shall be painted with water resistant paint conforming to IS: 986. The outer surface of the cooler shall be spary painted with synthetic enamel paint of approved shade/tint. (iii) The desert cooler shall be fitted with adjustable grill with separate on/off switch of 5/6 Amp rating (ISI Marked) for cooler fan and water pump and three stage speed regulator (Low, Medium, High) for three speed cooler fan motor. (iv) Suitable nylon bushes shall be provided in the grill for easy and smooth movement of louvers. (v) The filter pads shall be contain wood wool.The filters pads shall be fixed over the panel and seured by clamping guard of galvanized wire of 2mm dia (approx) squre /rectangular.The wire guard shall be fixed in the clamps to avoid any sagging.

M&L surface excavation n.exc 30cm deep and averaging 15cm deep in any type of soil complete all as specified and directed.

Dismantling and taking down old unserserviceable ACSR Conductor of any size from LT Poles and removing from site complete all as specified and directed.

Dismantling and taking down old unserserviceable GI Earth continuity wire, cradles etc of any size from LT Poles and removing from site complete all as specified and directed.

Dismantling and taking down old unserviceable cross -arms, bracing support clamps and back plates etc from LT Pole any size, complete all as specified and directed.

Dismantling and taking down old unserserviceable insulator any type and size from LT Poles and removing from site complete all as directed.

S&F SMC street pole mounted juction box in PVC of Make Sintex made out of one piece totally enclosed,weather proof,frount openable ,water proof, having aluminium bus bars 100 Amp single phase and neutral with one No MCB SPN 6 Amp for street light, cable entry from bottom, maintenance free size 300x200x100 mm fixing on pole with MS flat 25x3mm clamp including nut bolts front openable all as specified and directed by Engineer-in-Charge.

Supply, lay, jointing and testing XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 Sqmm 2 Core cable laid in trenches/ducts/fixed on poles/walls/passing through pipe under road crossing/paths/drain /culverts etc all as specified and directed. Note : Excavation & earth work, GI pipe for laying of cable, sand cushioning, cable protection cover shall be measured and paid for separately.

Supply, lay, jointing and testing XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 3.5 Core cable laid in trenches/ducts/fixed on poles/walls/passing through pipe under road crossing/paths/drain /culverts etc all as specified and directed. Note : Excavation & earth work, GI pipe for laying of cable, sand cushioning, cable protection cover shall be measured and paid for separately.

Supply, lay, jointing and testing XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 Sqmm 3.5 Core cable laid in trenches/ducts/fixed on poles/walls/passing through pipe under road crossing/paths/drain /culverts etc all as specified and directed. Note : Excavation & earth work, GI pipe for laying of cable, sand cushioning, cable protection cover shall be measured and paid for separately.

Supply, lay, jointing and testing XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 Sqmm 3.5 Core cable laid in trenches/ducts/fixed on poles/walls/passing through pipe under road crossing/paths/drain /culverts etc all as specified and directed. Note : Excavation & earth work, GI pipe for laying of cable, sand cushioning, cable protection cover shall be measured and paid for separately.

Supply, lay, jointing and testing XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 Sqmm 3.5 Core cable laid in trenches/ducts/fixed on poles/walls/passing through pipe under road crossing/paths/drain /culverts etc all as specified and directed. Note : Excavation & earth work, GI pipe for laying of cable, sand cushioning, cable protection cover shall be measured and paid for separately.

Supply, lay, jointing and testing XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 120 Sqmm 3.5 Core cable laid in trenches/ducts /fixed on poles/walls/ passing through pipe under road crossing/paths/ drain /culverts etc all as specified and directed. Note : Excavation & earth work, GI pipe for laying of cable, sand cushioning, cable protection cover shall be measured and paid for separately.

M&L for sand cushioning for under ground cable 23cm thick (one layer of 8cm thickness before laying the cable and other layer of 15cm thickness after laying the cable) and washed sand and punning to provide a required cover complete all as specified and directed. Note :- thickness after punning shall be considered for payment.

M&L Galvanized steel tubing 100 mm bore light grade, ISI marked for protection of under ground cable on poles laid in trenches/under road/drains, fixed to poles/walls with required size of flat iron (25mm x 3mm) clamps, bolts, nuts and washers for protection of LT electric cable complete. Note : Excavation and earth work shall be measured & paid separately under respective items.

M&L Galvanized steel tubing 80mm bore light grade, ISI marked for protection of under ground cable on poles laid in trenches/under road/drains, fixed to poles/walls with required size of flat iron (25mm x 3mm) clamps, bolts, nuts and washers for protection of LT electric cable complete. Note : Excavation and earth work shall be measured & paid separately under respective items.

M&L Galvanized steel tubing 50mm bore light grade, ISI marked for protection of under ground cable on poles laid in trenches/under road/drains, fixed to poles/walls with required size of flat iron (25mm x 3mm) clamps, bolts, nuts and washers for protection of LT electric cable complete. Note : Excavation and earth work shall be measured & paid separately under respective items.

M&L Galvanized steel tubing 40mm bore light grade, ISI marked for protection of under ground cable on poles laid in trenches/under road/drains, fixed to poles/walls with required size of flat iron (25mm x 3mm) clamps, bolts, nuts and washers for protection of LT electric cable complete. Note : Excavation and earth work shall be measured & paid separately under respective items.

M&L trenchless boring in any strata of soil across road, pavement, hardstanding etc by using modern ultra sound technology upto a depth as directed but not less than 0.60 mtr below GL/ road, pavement, hardstanding etc level for laying of LT cable under road, pavement, hardstanding etc without damaging existing under ground materials including provision of HDPE pipe of 80mm dia of 0.4mpa working pressure complete all as directed.

Supply, installing, testing and commissioning, factory made and tested Bus bar chamber outdoor type of size 60x45x45cm, made out of 3.15mm thick CRCA MS sheet and 50mmx50mmx8mm thick angle iron frame work, IP-65 class protection, powder coated finish over one coat of red oxide primer front & rear openable type, with locking arrangement {including provn of 65mm Godrej (Freedom) lock with 2 keys for each side opening} consisting of 04 Nos insulated copper bus bars 200 Amps rating on porcelain insulators. Bus bar chambers shall be mounted/fixed in ground/floor using 04 Nos angle iron of size 50mmx 50mm x 8mm welded/fixed to Bus bar chamber of height as directed including making post holes in ground and embedding angle iron in PCC 1:2:4 type B-1 complete all as specified and as directed. The Bus bar chamber shall following:- (a) MCCB 100 Amps four pole rupturing capacity 25 KA., 415 V AC , 50 Hz confirming to IEC 60947-2 & IS – 13947-3 thermal magnetic release and adjustable over load setting 0.8 – 1.0 x In adjustable short circuit setting 6 – 10 x In - 01 No. (b) Indicating lamps-01 set of three Notes (a) All armoured cables shall enter through bottom of the feeder pillar duly glanded and socketed. (b) All the out going cable shall also be glanded and socketed. (c) Cost of glanding/socketing etc are deemed to be included in the unit rate of Bus bar chamber.

Supply, installing, testing and commissioning, factory made and tested (incl CPRI type test certified), LT feeder pillar box (KIOSK) of appropriate dimensions (as per Indian Electricity rules) to accommodate following components, outdoor type, platform mounted, suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system, having bus bar chamber with insulated Aluminium bus bars 1000 Amps rating installed on porcelain insulators. The panel shall be dust and vermin proof, IP 65 class protection and made of 3.15mm CRCA MS sheet and 50x50x8mm thick angle iron frame work, powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, front & rear opening type, with aprons for cable entry, with double door shutter and locking arrangement (including provn of 65mm Godrej (Freedom) lock with 2 keys, internal wiring with PVC insulated, multistranded copper conductor, FRLS cables, IS-694 marked of adequate size but not less than 4 sqmm. The scope of work includes the following:- Incoming (a) Aluminium bus bar rating 1000 Amps four pole incl PVC heat shrink sleeves (RYB &N) : 01 Set (b) MCCB four pole 250 Amp confirming to IEC 60947-2 & IS – 13947-3 thermal magnetic release and adjustable over load setting 0.8-1.0 x In and adjustable short circuit setting 6-10 x In and rupturing capacity 36 KA at 415 V AC, 50 Hz complete - 01 No

Outgoing (a) MCCB four pole 100 Amp confirming to IEC 60947-2 & IS – 13947-3 thermal magnetic release and adjustable over load setting 0.8 – 1.0 x In and adjustable short circuit setting 6 – 10 x In and rupturing cap 25 KA at 415 V AC, 50 Hz - 04 Nos. (b) MCCB four pole 63 Amp confirming to IEC 60947-2 & IS – 13947-3 fixed type and rupturing capacity 16 KA at 415 V AC , 50 Hz complete - 01 Nos. (c ) MCCB four pole 40 Amp confirming to IEC 60947-2 & IS – 13947-3 fixed type and rupturing capacity 16 KA at 415 V AC , 50 Hz complete - 02 Nos. Control System (a) Amp meter (0-400A) analog type 96mm Square dial –01 No. (b) Volt meter (0-500V) analog type 96mm Square dial – 01 No (c) Three way rotary switch for volt meter/ammeter – 02 Nos (d) CT of ratio 400/5 – 01 Set of Three (e) Indication lamps R,Y,B (LED type) with toggle switch - 01 Set

(a) All armoured cables shall enter through bottom of the feeder pillar duly glanded and socketed and connected to MCCB/cable terminal. Cost of glanding socketing etc are deemed to be included in the unit rate of feeder pillar. (b) All the out going cable shall be terminated in bakellite cable connector and shall be duly glanded and socketed. (c) All the cables (power and control wiring ) should be terminated duly socketed with heavy duty tinned copper lugs, GI bolts/screws nuts, flat washers and spring washers as required. (d) Wh+B174ite acrylic marker plate (for feeder / switch marking ) to be provided with black lettering by heat press machine as indicated in drawing and to be pasted over the panel door/near the cable connector with high quality adhesive. (e) The cost of platform/foundation with PCC shall deemed to be included in the quoted rates.

S&F 2.5 Sqmm PVC insulated copper conductor three core including steel conduit fixed on pole (PCC/Steel Tubular) from street light box to street light fitting with clump nuts and bolts etc as directed by Engineer-in-Charge.

Hitesh Construction

M/s ASK Enterprises