SPL REPAIR TO BLDG NO. P-37, P-38, P-39 AND P-40 OR MD ACCN ALONGWITH PATH, DRAIN AND SEWAGE LINES AT BIKRAM ENCLAVE UNDER GE (SOUTH) UDHAMPUR

Amount

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (Reinforcement cut as required to facilitate demolition), complete all as specified.

Demolition of cement concrete in ground floors and paving not exceeding 15cm thickness (below or above ground level) un-reinforced, complete all as specified.

Glazed coloured ceramic tiles in dado/vertical surface (350mm x 250mm x7mm/ 450mm x 300mm x 7mm) thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface, over and including 10mm thick plaster in cement mortar 1:4, complete all as specified and as directed.

Non skid, coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified and as directed.

Non skid, coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified and as directed.

Non skid, coloured ceramic tiles 7 to 8mm thick as in skirting set and jointed in neat cement slurry and pointed in coloured cement to match the surface, over and including 10mm thick plaster in cement mortar 1:4, complete all as specified and as directed..

25 mm thick, Plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in sub base for laying floor finishes including finishing the surfaces even and fair without using extra cement, complete all as specified and as directed.

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab in floor including rubbing and polishing over & including screed bed or bedding layer 15mm thick in cement mortar (1:4) complete, all as specified and as directed.

Machine cut kota stone 18-20mm thick as in riser of steps, skirting, dado and pillar laid over cement screed base and jointed with white cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, over & including 10 mm thick rendering in CM (1:3) complete all as specified and as directed.

150mm wide strip of makrana white marble 18-20 mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing over and including 15 mm thick CM 1:4 mortar backing for fixing the stone slab, complete all as specified and as directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, removing all type of vegetation (like peeple tree etc) scrubbing down with water complete, all as specified and as directed.

20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified & directed.

Moulding of granite stone/kota stone, full round, complete all as specified & directed.

15mm thick plastering in cement mortar 1:4 on fair faces of brick surfaces or concrete surfaces, surface finished even and smooth without using extra cement but using integral water proofing compound as per manufacturer,s instructions, complete all as specified. Note : Integral water proofing compound shall be measured & paid seprately.

15mm thick rendering on brick or concrete surfaces in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and as directed.

10mm thick rendering on brick or concrete surfaces as in ceiling in cement mortar 1:3, and finish the surface even and smooth without using extra cement, complete all as specified and as directed.

Supply only integral water proofing compound, complete all as specifed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed.

Description all as per item No. 18 above but area exceeding 1.50 square metre and not exceeding 4 square metre each.

Solid frame wood high density filament (HDF) double rebated of size 125x55mm/105x60mm processed with polyole fins and different wood fibre, fixed to opening including necessary lugs, hinges, lock strike plate etc., complete all as specified and as directed.

Solid PVC door frame wood grain colour coated of size 50 x 95mm made out of 5mm wood grain colour PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings complete all as specified & directed.

Factory made solid UV wood grain printed panelled/plain PVC single piece door shutter 30mm thickstyle, consisting of frame made out of MS tube 19 gauze thickness & size of 25mm x 25mm for sitities, top and bottom rail MS frame shall have a coating os steel primer, the frameshall be vocered with heat moulded wood grain UV printed PVC sheet tape fixed in MS frame welded sealed to the syles and rail with suitable PVC sheet Beading and jointed tohther with solvent cement complete all as pecied and directed by Engr-in Charge, manufacture specification as per drawing. The shutter is to be fixed with 50 mm size self drilling star screws full threated.

35 mm thick HDF prelaminated (wenga/teak colour) moulded shutter 35 mm thick puf (poly ucrane from) insulation with minimum density 40 kg/cum filled in between two HDF sheets of thickness 3.2 mm both & border covered with 10mm thick PVC sheet complete in all respect with lock rail & beautified by PVC bedding all around with PVC solvent complete all specified and as directed.

Prelaminated 18/19mm thick lead factory made 100% solid WPC (wood poltmer composite) sheet having natural fibre conter 25 to 30% wood colour sheets with density not less than 500 kg/cum and the weight of sheet of 1 sqm should be 11 kg (+/- 5%) manufactured by ISO 9001-2015 certified company the sheet should be 100 % water proof, termite proof, fire ratardant, manufactured by single layer extrusion process with excellent screw holding capacity and shore D hardness, complete all as specified and as directed,

18/19mm thick Prelaminated particle board, termit proof, chemically well pressed, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, as in kitchen cabinet, cub boards, shelves etc including 6mm thick teak wood beading all around complete all as specified and as directed.

34/35mm thick factory made single piece wire gauge door/ shutter solid PVC UV printed doors-wood free consisting of 5mm thick solid PVC sheet on both side (both side multi color UV printed using steel/ aluminium XPM/ wire mesh and consisting frame made out of M.S tubes 19 guage thickness and size of 19mm x 19mm for stilies and 19mm x 19mm for the top, bottom and lock rails with PVC beading in all around M S frame shall have a coat of metal primers. MS frame shall be covered with heat moulded (Rigid) 20/22mm PVC solid sheet at styles, top rail and bottom rail (Rigid) MS frame welding sealed to the style and with suitable PVC sheet beading and joined together with solvent complete all as specified and as directed. Note: The shutter is to be fixed with 50mm size self drilling star screws full threated.

Steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and as directed. Notye : i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Description all as per item above No 27 but without glazing bar complete all as specified and as directed.

Factory made mild steel ventilators (box type) with upper top hung shutters and bottom fixed type shutters including pintol hinges, steel peg stay and one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1302/2009 Sheet 1/3 to 3/3. ii) MS fillets, glazing, wire gauge shall be measured and paid for separately

Mild steel framed work such as grills, gratings, etc. With ends of bars shouldered and/or riveted or gorged into spikes, framed guard bar, barred iron doors; ladder, framed balusters; railing; frame work for water tanks, cooler stand etc and similar work conforming to FE 290-0 or Gde-E-165, complete all as specified and as directed.

3mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and as directed by Engr-in-Charge.

3mm thick figured glass (frosted) ,pin head type and glazing with oil putty not exc 0.50 Sqm in each pane fixing to window/ventilator complete all as specified and as directed by Engr-in-Charge.

Stainless steel mosquito proof wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with aluminium falt/channel and screw complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed.

Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, complete all as specified and as directed.

Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 but EXCEPT BRICKS, complete all as specified and as directed.

Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius in half brick thick built in cement mortar 1:4, complete all as specified and as directed.

Plain cement concrete as in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneeless apex stones , bed plates, kerbs, hold fasts etc. including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 complete all as specified and as directed.

Roughening surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 kg/Sqm including 10mm thick screeding in CM (1:3) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately). Applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and provide modified polymeric APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polyethylene film. Min wt of membrane will be 3.50 Kg/Sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitument 85/25 @ 1.2 Kg/Sqm blinded with fine sand in dry condition @ 0.5 Kg/Sqm, complete all as specified and as directed.

Factory made cement concrete tiles 20cm x 20cm and 20mm thick, machine pressed; set jointed and pointed in neat cement slurry with grey cement & no pigments and in floors, and cut and polished , over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes, complete all as specified.

75 mm thick cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints through out the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete, all as specified and directed.

Mild steel sliding door bolt, bolt type, stove enamelled black, with bright bolt not less 12mm dia, with and including a minimum of 6 bolts and nuts, 4 on bolt plate and 2 on stapple plate, 250mm long (ISI marked), complete all as specified.

Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 30mm, complete all as specified.

Mild steel pressed handle, oval type, stove enamelled black, 150mm long (ISI marked), complete all as specified.

100mm size hasp & staple, aluminium, safety type, including bolt to hinge plate and fixed with screws, complete all as specified.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 150mm long (ISI marked), complete all as specified.

Extruded aluminium alloy handle, fabricated type, anodised, 150mm long (ISI marked), complete all as specified.

Small fittings such as bracket of any type, latch and hinge blocks, shaped door and window stops and the like including all necessary labour, article not exc. 200 cucm each of IInd class hard wood.

Butt hinges, medium weight, cold rolled, mild steel 100 mm long (ISI marked) fixed to mild steell/angle iron frame by welding, if required, complete all as specified.

Butt hinges, medium weight, cold rolled, mild steel 75mm long (ISI marked) fixed to mild steell/angle iron frame by welding, if required, complete all as specified.

300mm ordinary rat tail rod pattern door spring including roller and roller plate of mild steel, complete all as specified.

Mild steel barrel tower bolts, stove enamelled black, with bright bolt, 200mm long (ISI marked), complete all as specified.

Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc., complete all specified & directed.

Viterous china wash basin, white flat back size 550 x 400mm including brackets, waste coupling brass chromium plated 32mm dia with lonh screwed shanks and flynut, flange end bedded in red lead cement and other end fixed, fixed in repairs, complete all as specified and as directed.

Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer, complete all as specified.

Preparation of newly plastered/ unplastered surfaces of wall and applying 1mm thick layer of wall care putty to give uniform surface, complete all as specified & directed.

Preparation old surfaces including complete removal of existing treatment ( white wash) and applying two coats of white wash on ceiling complete all as specified and as directed.

Preparation of new plastered surfaces of ceiling and applying two coats of white wash, complete all as specified.

Preparation of old surfaces of walls and applying two coats of Oil Bond distemper over a coat of wall primer, complete all as specified and directed.

Preparation of new surfaces of walls and applying two coats of Oil Bond distemper over a coat of wall primer, complete all as specified and directed.

Preparation of old plastered or unplastered surfaces of wall and applying two coats of cement base paint over and including a coat of primer, complete all as specified and as directed.

Preparation of newly plastered or unplastered surfaces of wall and applying two coats of cement base paint over and including a coat of primer, complete all as specified and as directed.

Preparation of old plastered or unplastered surfaces of wall (including facia) and applying two coats of weather proof exterior emulsion paint (apex) painting on walls, complete all as specified and as directed.

Water closet (Orissa pattern) including lime concrete bedding, vitreous china long pan orissa pattern 580x440mm, white with integral foot rests (excluding flushing cistern & flush pipe) fixed in repairs, complete all as specified and as directed.

Supply only Cast iron ‘P’ trap, bore of pipe 100mm, complete all as specified.

10 ltr capacity PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with twin flush provision with and including PVC long bend flush pipe 90cm long, complete all as specified and as directed.

Stainless steel grating doom 75mm/100mm square/round as directed, complete all as specified.

Tubular towel rails brass chromium plated, 20 mm dia, D type, 60 cm long between flanges, fixed with rawl plugs fixed in repairs complete alll as specified and as directed, Make : Jaquar Cat Part No CAN-CHR-1111NM/ Cera Cat Part No B2210106 or equivalent make as mentioned in Particular Specifications.

PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

Magic eye, brass, chromium plated, fixed in main door complete all as specified and as directed by Engr-in-Charge.

Steel peg set colour coated of six as per sample in repairs complete all as specified and as directed.

Sink made of stainless steel 1mm thick for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever cast iron bracket, connecting union etc. and overall size 495x420mm with bowl size 410x330x160mm, complete all as specified & directed.

Stainless steel plate rack made out of 0.63mm thick steel sheet, minimum size 600 x 750 x 250mm of standard quality and shape, fixed in repairs complete all as specified and as directed. Make: Prayag Cat Pt No P-330 or equivalent of Jayna/ Neelkanth/Nirali.

Plain cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregates as in surface channel and drains, complete all as specified and as directed.

Plain cement concrete 1:5:10 type E-2 using 40mm graded crushed stone aggregates as in sunken floor/ foundation, complete all as specified and as directed.

Dismantling cast iron pipe & reinforced concrete drain pipes, jointed in cement mortar of any dia taking out from trenches or fixed to wall upto 100mm complete all as specified and as directed.

Cast iron soil, waste and vent pipes (Sand cast pipes) in any length with or without ears, with cement joints laid in trenches or in floors of 100mm bore, complete all as specified and as directed.

Cast iron soil, waste and vent pipes (Sand cast pipes) in any length with or without ears, with cement joints laid in trenches or in floors of 75mm bore, complete all as specified and as directed.

Cast iron soil, waste and vent pipes (Sand cast pipes) in any length with or without ears, with cement joints fixed to wall or in floors of 100mm bore, complete all as specified and as directed.

Cast iron soil, waste and vent pipes (Sand cast pipes) in any length with or without ears, with cement joints fixed to wall or in floors of 75mm bore, complete all as specified and as directed.

Cast iron soil, waste and vent pipes (Sand cast pipes) in any length with or without ears, with cement joints fixed to wall or in floors of 50mm bore, complete all as specified and as directed.

Cast iron bends (any radius diminishing pieces or tapes (larger bore measured), 100mm bore fitted with oval access door fixed with rubber ring joints as in repairs complete all as specified and as directed.

Cast iron bends (any radius diminishing pieces or tapes (larger bore measured), 75mm bore fitted with oval access door fixed with rubber ring joints as in repairs complete all as specified and as directed.

Stack clamps out of 50mm by 5mm flat iron and 6mm dia round iron stays,including bolts and nuts and securing ends of stays to wall or roof for 100/110 mm bore of pipe complete all as specified and as directed .

Stack clamps out of 50mm by 5mm flat iron and 6mm dia round iron stays,including bolts and nuts and securing ends of stays to wall or roof for 75mm bore of pipe complete all as specified and as directed.

Cast iron branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches 75 bore, fitted with oval access door as in repairs complete all as specified and as directed.

Cast iron branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches 100 bore, fitted with oval access door as in repairs complete all as specified and as directed.

Taking down eaves gutters and and rain water pipes (any size or pattern ), including all fittings incl removal of store and sold to contractor through credit.

110mm PVC (SWR) pipes single/Double socketed of any length with rubber ring joints pressure rating 4 kg/cm2 fixed to wall incl clamp etc, complete all as specified and as directed.

110 mm bore PVC SWR bends and fixed with joint sealent etc, complete all as specified.

75mm cast iron cowls as in repairs complete all as specified and as directed.

50mm Cast iron cowls as in repairs complete all as specified and as directed.

75mm Cast iron floor traps with grating including jointing to waste pipe fixed cncrete type B1 (1:2:4), complete all as specified and as directed.(ISI Mark)

Cast iron lids for oval access doors for 75mm bore pipe and fittings including all necessary threading and nut/bolt as required, complete all as specified and as directed.

Cast iron lids for oval access doors for 100mm bore pipe and fittings including all necessary threading and nut/bolt as required, complete all as specified and as directed.

Soap dish, mild steel chromium plated, fixed in repairs complete all as specified and as directed. Make: Jaquar cat Part No ACN 1131FN or equivalent make as mentioned in Particular Specifications.

Towel rack, mild steel chromium plated, fixed in repairs complete all as specified and as directed. Make: Jaquar cat Part No ACN 1181N or equivalent make as mentioned in Particular Specifications.

Front glass shelf with chromium plated guard rails, fixed in repairs complete all as specified and as directed. Make: Jaquar cat Part No ACN 1171N or equivalent make as mentioned in Particular Specifications.

Corner glass shelf with chromium plated guard rails, fixed in repairs complete all as specified and as directed. Make: Jaquar cat Part No ACN 1173N or equivalent make as mentioned in Particular Specifications.

15mm bore CP central hole basin mixture with round spout without popup waste system with 450mm long braided houses, fixed in repairs complete all as specified and as directed. Make: Jaquar cat Part No CON 167KNB or equivalent make as mentioned in Particular Specifications.

15mm bore chromium plated mixer with swinging casted spout (Wall mounted model), fixed in repairs complete all as specified and as directed. Make: Jaquar cat Part No CON 347KN or equivalent make as mentioned in Particular Specifications.

15mm bore long body bib tap, fixed in repairs complete all as specified and as directed. Make: Jaquar cat Part No CON 037KN or equivalent make as mentioned in Particular Specifications.

15mm bore bib tap, fixed in repairs complete all as specified and as directed. Make: Jaquar cat Part No CON 107KN or equivalent make as mentioned in Particular Specifications.

15mm bore angular stop cock with wall flange, fixed in repairs complete all as specified and as directed. Make: Jaquar cat Part No CON 059KN or equivalent make as mentioned in Particular Specifications.

PVC connection 15mm bore 450mm long braided hose with M10X1 Nipple, 15mm Nut, O-ring and rubber washer, fixed in repairs, complete all as specified and as directed. Make: Jaquar cat Part No ALD 803AB or equivalent make as mentioned in Particular Specifications.

PVC connection 15mm bore 450mm long braided hose with two 15mm Nut, O-ring and rubber washer, fixed in repairs, complete all as specified and as directed. Make: Jaquar cat Part No ALD 805B or equivalent make as mentioned in Particular Specifications.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings including ridges, complete all as specified and as direceted.

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as direceted.

Mild steel work as in wind ties for roof including securing bolts etc. including all necessary drilling, bolting or riveting etc. and similar work, conforming to Fe-410-0 or Fe-310-0, complete all as specified.

Dismantling timber scantling 40 Sqcm and over in section, in any position (unframed work), complete all as specified.

Rolled mild steel work in main and cross beams, hip and jack rafters; purlins where connected to comman rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, conforming to Fe-410-0 or Fe-310-0, complete all as specified & directed.

Taking up or down steel tubing of 15 mm bore with connections for cleaning for refixing or removing from site, complete all as specified and as directed.

Taking up or down steel tubing of 20 mm bore with connections for cleaning for refixing or removing from site, complete all as specified and as directed.

15mm bore galvanised steel water tubing medium grade (ISI Marked) with and including all fittings and fixed complete to walls and or laid under floors etc complete all as specified and as directed.

20mm bore galvanised steel water tubing medium grade (ISI Marked) with and including all fittings and fixed complete to walls and or laid under floors etc complete all as specified and as directed.

Gun metal globe of gate valve with iron wheel head, screwed both ends of size 20mm, fixed in repairs, complete all as specified and as directed

Gun metal globe of gate valve with iron wheel head, screwed both ends of size 15mm, fixed in repairs, complete all as specified and as directed.

Stop valves, fancy type chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of bore 15mm, fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

Stop valves, fancy type chromium plated with long shank concealed type, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of bore 15mm, fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

Bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle screwed down for iron pipe or for brass ferrule for bore of pipe 15mm, fixed in repair, complete all as specified and as directed by Engr-in-Charge.

Rotational moulded polyethylene water storage tank, two layers, inner and outer white, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 1000 litres each including all accessories {i.e GI nipples and Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of bore 20mm (Minimum weight 210 gram) etc}, including taking down old, complete all as specified and as directed.

Shower roses 15 mm chromium plated with or without swivel joints, any size, including 125 mm long arm and fixing to steel pipe or union, fixed in repairs, complete all as specified and as directed.

Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil, complete all as specified & directed.

75mm thick PCC 1:4:8 Type D2 using 40 mm graded stone aggregates as in foundations filling and mass concrete., complete all as specified and as direceted.

Sand cushioning under floors including watering and consolidation complete all as specified and as direceted.

Machine pressed / vibro mechenically floated coloured interlocking cement paver block ISI marked, any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 Grade, with topping of cement with imported pigment. Shape shall be approved by GE.

Removing excavated material (soils) to a distance exc. 50m but not exc 1.5km outside defence land and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified.

Machine pressed (factory made) Precast cement concrete 1:2:4 mix type B-1 kerb stone of size 300mm x 300mm x 100mm and setting in cement mortar 1:4, complete all as specified and as directed.

Hard core of gauge not exc 63mm using broken stone or boulders, deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface, complete all as specified.

Dismantling old abondoned existing manholes any depth with debberis and removing making good to earth, complete all as specified and as directed.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc to obtain rough flat finished surface of concrete complete all as specified and as directed.

TMT mild steel bars, 6mm to 8mmm dia, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and includingMS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed.

Mild steel framed work as in frames to manhile covers of angle iron or other section including holdfast conforming to Fe 290-0 or Gde-E-165, complete all as specified and as directed.

Pre-cast RCC cement concrete 1:2:4 type B-I (20mm graded) as in manhole cover slab and in similar works bedded and jointed in cement morter 1:4, complete all as specified and as directed.

Brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:4 all complete all as specified and as directed.

Plain cement concrete 1:2:4, nominal mix, type B-1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, benching, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified.

Cleaning of gully traps of any size and burrying in pits the waste materialsafter removing upto 50 metres as directed.

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, for laying cables/pipes, etc. not exceeding 10 sq m on plan and not exceeding 1.5 m in depth in any type of soil and getting out soil, complete all as specified and as directed.

Returning, filling in (soil) including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in any type of soil, complete all as specified and as directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and as directed.

Demolition and breaking up drain pipes, 100/150mm internal dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar, including concrete bedding and haunching complete all as specified and as directed.

Plain cement concrete (1:4:8) type D2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

Plain cement concrete 1:4:8 type D-2 (using 40mm graded aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 100mm bore pipes all as specified. Note:-(i) Thickness of bed below barrel of pipe-10 Cms. (ii) width of bed- outer dia of pipe plus 30 cms.

Salt-glazed stoneware drain pipe, internal dia of pipe 100mm, laid in trenches and jointed & tested, complete all as specified.

Plain cement concrete 1:4:8 type D-2 (using 40mm graded aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm bore pipes all as specified. Note:-(i) Thickness of bed below barrel of pipe-10 Cms. (ii) width of bed- outer dia of pipe plus 30 cms.

Salt-glazed stoneware drain pipe, internal dia of pipe 150mm, laid in trenches and jointed & tested, complete all as specified.

Plain cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) as in surface channels and drains including necessary formwork, complete all as specified and as directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc., complete all as specified.

Construction of soakage well 3m dia x 3m depth (Internal dimensions), brick construction, complete all as specified and as shown on drawing No CE/TD-1202/2003 dated 09 Oct 2003 (Revised upto 14.1014).

Construction of septic tank 50 Users, brick construction, complete all as specified and as shown on drawing No CEUZ/TD-1202/2003 dated 09 Oct 2003 (Revised upto 14.10.14).

Demucking of filled soil in drains af any size, depth or section in any condition as per requirement as directed at site.

15mm thick plastering in cement mortar 1:4 on fair faces of brick surfaces or concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified.

RCC 1:2:4, nominal mix, type B-1, using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified.

Form work to edges of concrete flats, break in floors, openings in concrete walls, floor and roof and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 20cm wide for rough finished surfaces of concrete, complete all as specified & directed.

Stone walling of random rubble with best quality locally available harder stone such as granite, trap or basalt, uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6, complete all as specified & directed.

Raised pointing to random or polygonal rubble, uncoursed or brought upto courses in cement mortar 1:3, complete all as specified.

Plain cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in surface channels and drains including necessary formwork, complete all as specified and as directed.

PVC (SWR) pipe, 110mm dia (ISI marked) in any length as in weep holes complete all as specified and directed.

Hand packing (any thickness) using broken stone or boulders of 80 to 150mm size at back of walls over arches etc., and raising (or lowering) to the required

Taking down carefully copper /aluminium, point wiring (light, fan, socket or power) complete including fittings and fixtures such as light fittings, switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of wall, ceiling, floors etc to match the existing, complete all as specified and as directed by Engr-in-Charge.

Taking down old unserviceable copper /aluminium,submain wiring any type/size from existing and making good disturbed surfaces of wall, ceiling, floors etc to match the existing, complete all as specified and as directed by Engr-in-Charge.

Taking down MCB DB SPN/TPN with all accessories carefully and making good disturbed surface of walls, complete all as specified and directed by Engr-in-Charge.

Point wiring with 1.5 Sqmm PVC insulated, unsheathed (FRLS) cable with multi stranded copper conductor wiring in and including PVC concealed conduit (ISI marked) 20mm dia and over, medium grade and all accessories for one light / fan controlled by one switch suitable for pressed GI terminal boxes (modular type) of required modules concealed on walls including inner and outer cover plates for fixing of modular switches/socket/ regulator etc along with PVC insulated and unsheathed FRLS 1.5 Sqmm multistrand copper conductor earth wire connected to common earth and earth dolly, fixed in repair, complete all as specified & directed by Engr-in-Charge. Note: Modular metal flush boxes & inner and cover plates deemed to be included in quoted rate.

Description all as per item No 165 above but for one light point controlled by 2-two way switches.

Description all as per item No 165 above but for 3/5 pin 6 Amp socket outlet on independent board .

Description all as per item No 165 above but for 3/5 pin 6 Amp socket outlet on the same board with other switch.

All as per description of Serial item No 165 here-in-before but one 3/5 pin 15 Amp socket outlet on independent board with PVC insulated, unsheathed FRLS cable 2.5 Sqmm copper multistrand conductor, along with PVC insulated and unsheathed FRLS 2.5 Sqmm multistrand copper conductor earth wire connected to common earth and earth dolly.

Switch piano, single pole, 1 module, one way, 6 Amp (modular type), 230V, 50 Hz AC, complete all as specified and as directed by Engr-in-Charge.

Switch piano, single pole, 1 module, two way, 6 Amp (modular type), 230V, 50 Hz AC, complete all as specified and as directed by Engr-in-Charge.

Switch piano, single pole,1 module, one way ,16 Amp (modular type), 230V, 50 Hz AC, complete all as specified and as directed by Engr-in-Charge.

Bell push Modular type, 1 module, 6 Amps 230 volts complete all as specified and as directed by Engr-in-Charge.

Socket outlet, 2 module, combined 3 pin, 6 Amp flush type modular type, complete all as specified and as directed by Engr-in-Charge.

Socket outlet, 2 module, 2 in 1- 3 pin combined, 6 & 16 Amp flush type modular type, complete all as specified and as directed by Engr-in-Charge.

Stepped type fan regulator 120W, 230V 50 C/S, 2 module, Deluxe Modular type electronic, hum free suitable control speed of fan from 0 to 100 %, complete all as specified and as directed by Engr-in-Charge.

Ceiling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Block, ,complete all as specified and as directed by Engr-in-Charge.

Bell (ding dong type), AC electronic type, 230 volts, single pole, 50 Hz complete all as specified and as directed by Engr-in-Charge.

Sheet metal enclosures for DBs when MCCBs to be used double door DB VTPN 4 ways, vertical type, including 125 Amps MCCB, 25 kA, 415 volts with 400 Amps rated bus bar and neutral link including chases wall for fixing DB and making good disturbed wall surface to match with existing specifications, complete all as specified and directed by Engr-in-Charge. (Including all PCC & cementing work for installation of TPN DB to wall).

Sheet metal enclosures for distribution board when MCB to be used SPN 12 way with IP-43, IK-09 protection 240V with 200 Amps rated bus bar, double door type including cutting chases in walls for fixing DBs making good the distubed surfaces to match with existing specifications, complete all as specified and as directed by Engr-in-Charge.

MCB SPN, 10 to 40 Amps, 240 Volts, rupturing capacity 10 KA "C" Series including providing aluminuium thimbles for outgoing cable, complete all as specified and as directed by Engr-in-Charge. Note : The exact capacity of MCB shall be as directed by Engr-in-Charge.

MCB SP, 10 to 40 Amps, 240 Volts, rupturing capacity 10 KA "C" Series including providing aluminuium thimbles for outgoing cable, complete all as specified and as directed by Engr-in-Charge. Note : The exact capacity of MCB shall be as directed by Engr-in-Charge.

MCB SPN, 63 Amps, 240 Volts, rupturing capacity 10 KA "C" Series including providing aluminuium thimbles for outgoing cable, complete all as specified and as directed by Engr-in-Charge. Note: Make of MCB and DB shall of same make for all connected items.

Sub main wiring with two runs of 10 Sqmm ( 2x10 sqmm ) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor conforming to IS-694 drawn through and including non-metalic PVC rigid concealed conduit 25 mm dia medium grade (ISI marked) with all conduit accessories mounting on suface of walls /roofs / ceiling etc with one run of 10 Sqmm (1x10sqmm ) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire, complete all as specified and directed by Engr-in-Charge. Note:- 2 runs of 10 Sqmm (2x10sqmm ) ,one run of 10 Sqmm (1x10 sqmm ) cable and one metre of conduit will be measured as one unit.

Sub main wiring with two runs of 6 Sqmm ( 2x6 sqmm ) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor conforming to IS-694 drawn through and including non-metalic PVC rigid concealed conduit 25 mm dia medium grade (ISI marked) with all conduit accessories mounting on suface of walls /roofs / ceiling etc with one run of 6Sqmm (1x6sqmm ) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire, complete all as specified and directed by Engr-in-Charge. Note:- 2 runs of 6 Sqmm (2x6sqmm ) ,one run of 6 Sqmm (1x6 sqmm ) cable and one metre of conduit will be measured as one unit.

Sub main wiring with two runs of 4 Sqmm ( 2x4 sqmm ) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor conforming to IS-694 drawn through and including non-metalic PVC rigid concealed conduit 25 mm dia medium grade (ISI marked) with all conduit accessories mounting on suface of walls /roofs / ceiling etc with one run of 4 Sqmm (1x4sqmm ) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire, complete all as specified and directed by Engr-in-Charge. Note:- 2 runs of 4 Sqmm (2x4sqmm ) ,one run of 4 Sqmm (1x4 sqmm ) cable and one metre of conduit will be measured as one unit.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground, (Earth pit not less than 2.25 mtr deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, connected to and including 4mm dia galvanized iron wire lead by means of bolts, nuts, check nuts and washers of galvanized standard iron or steel all as specified or indicated in electrical plate No 3 of MES Part-I, including testing on completion including the material and labour and taking out old unserviceable earthing of the following :- (a) Excavation and earth work for drilling hole for electrode in any type of soil. (b) PCC pit in cement concrete 1:2:4 type B-1. (c) Precast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than 1.87 Kg/Sqm. (d) Funnel with watering pipe of GI 20 mm nominal bore medium grade and copper lugs etc all as specified.

Srl item No 187 Contd … (e) 15 mm nominal bore light grade GI protection pipe 7.5 mtr long for protection of earthing lead from mechanical injury or tempering. (f) Requisite quantity of common salt and charcoal. (g) Testing of earthing. Note : On testing after completion of earthing, if the desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk and cost to the entire satisfaction of the Engineer-in-Charge.

Single phase electric energy meter box made of polycarbonate body with locking arrangement and fixed, complete all as specified and as directed.

Taking down ceiling / exhaust fan, sealing cable end, dismantling blades and removing fan and blades to store, incl oiling, greasing, cleaning slot, overhauling & replacement of defective nut, bolt , washers etc. and applying two coat painting with synthetic enamel to fans complete, in situ by spraying including filling cavities with filler, one coat after cleaning all dust etc., making all connection using 1.5 sqmm copper conductor multi strand PVC insulated 2 core flexible cable from ceiling rose and rehanging/ refixing complete all as per the directions of Engr-in-Charge.

Angular holder with rectangular base including round block, complete all as specified.

Led bulb 15W, 230 Volts AC and fixed complete all as specified.

Decorative ultra slim linear surface mounted LED lighting fixture (4 feet length), 20Watt LED with integral electronic driver complete making connection and testing after fixing, fixed in repair, complete all as specified and directed by Engr-in-charge.The specification of light fitting should meet the following : - (a) Housing of Light fitting : Aluminium Extruded (b) Operating Voltage : Between 150 V- 270V (c) Operating Temperature : -10 to +45 Degree Centigrade (d) Lumen efficacy : Not less than 110 lm/W (e) System Lumens : Not less than 2000 lm (f) Colour Temperature : Not less than 5700K (g) Surge Voltage Protection : Up to 2KV (h) Ingress protection : IP 20 (j) Total Harmonic Distortion (THD) : Not less than 20% (k) Power factor : Not less than : 0.90 (l) Line protection : Under/Over voltage Protection (m) Input Frequancy : 50 Hz

9/10 watt LED Bulk Head Light energy saving with IP65 with opal diffuser, pressure die cast aluminium housing & ring for sturdiness & corrosion resistant, epoxy powder coated, isolated driver, with system efficacy ≥ 100 Lm/watt, operating voltage 170-240 volt, colour temp 6500K, Low heat generating LED (Make of LED shall be CREE/Nichia/Osram) complete making all connection using 1.5 sqmm copper conductor multi strand PVC insulated 2 core flexible cable from ceiling rose to fitting complete all as per the directions of Engr-in-Charge.

LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and as directed by Engr-in-Charge.

New generation energy saving and environmental friendly long life LED street light of 35 watt with high power LED as lighting source and lens embedded PC cover having TOP OPENING seperate driver compartment and impact resistance of IK07 with High efficiency long life LED with SMD LED on MCPCB Powered by Built-in, isolated electronic LED driver (SMPS based constant current supply) complete making connection and testing after fixing, complete all as specified and directed by Engr-in-charge. The specification of light fitting should meet the following : - (a) Housing of Light fitting : Aluminium Die Cast (b) Diffuser : High efficient LENS Optics (c) Operating Voltage : Between 140 V- 270V (d) Operating Temperature : -10 to +50 Degree Centigrade (e) Lumen efficacy : Not less than 100 lm/W (f) System Lumens : Not less than 2500 lm (g) Colour Temperature : Not less than 5700K (h) Surge Voltage Protection : Up to 4KV (j) Ingress protection : IP 65 (k) Total Harmonic Distortion (THD) : Not less than 20% (l) Power factor : Not less than 0.9 (m) Line protection : Under/Over voltage Protection (n) Input Frequancy : 50 Hz

Street light Bracket complete made of GI pipe 32mm bore, light grade of suitable size, 1.2m long bent to shape as per site requirement alongwith MS flat iron clamps with nuts, bolts, washers including grouting the same with wall , complete all as per the direction of Engr-in-Charge.

Supply, laying and testing of XLPE insulated sheathed armored heavy duty LT 1100 Volts grade cable with aluminum conductors laid in trenches/pipe, fixed to poles, walls of size 25 sqmm 3.5 core including taking up/down old unserviceable cables. complete all as specified and as directed by Engr-in-Charge.

Dry coarse sand as cushioning to under ground cable provided with layer of 8 cms deep before laying the cable and 15 cms deep after laying and stretching the cable, punned to 18 cm thick complete all as specified and as directed by Engr-in-Charge. NOTE Only punned thickness shall be measured for payment purpose.

Sub class ‘B’ old size well burnt bricks, laid flat in trenches as protection to cable, complete all as specified and as directed by Engr-in-Charge.

GI tubing light grade 40mm dia along the wall/in trenches/in duct/in culvert/road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holding of GI pipe alongwith poles, complete all as specified and as directed by Engr-in-Charge.

Modular TV socket outlet single with inner and outer cover strip required moduele including TV cable required length form roof complete all as specified and directed by Enger In charge.

Removing and refixing only LED lights fitting 5W to 20W, 220V, AC decorative box type with driver, holder including LED tube light C & S Make connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed

Removing and refixing water heater, 25 ltr capacity 220V, AC single phase including nut bolt, copper conductor cable of suitable size, one coat of synthetic enamel white spray painting complete all as specified and directed.

KALSOTRA CONSTRUCTION CO

jyoti parkash sharma

SINGH CONST CO

M/S ASHOK KUMAR PACHIALA