Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
₹14.0 L
EMD Value
₹27,980
Closing Date
6 Jun 2024, 5:30 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
LCA Tejas Division, Bangalore
HINDUSTAN AERONAUTICS LIMITED LCA Tejas Division, Bangalore
Upgradation of Receptions at Admin. and Material Gates of LCA Tejas Division- Plant-I, HAL BC.
7516
HAL/LCA-Tejas/PM/C-07/2024
Works
Bangalore Complex-LCA-PG
₹0
₹27,980
6 Jun 2024
16 May 2024
16 May 2024
6 Jun 2024
Providing and fixing of Polygranite wall sheeting of minimum 3mm thickness of approved design/colour/pattern by HAL. The rate is inclusive of cleaning the wall surface, and preparing the wall surface making good for fixing the polygranite sheet, primer-bond coat, providing necessary cut outs for switches, cables, and any other fixures. Fixing the poly granites with suitable adhesives as per manufacurers instruction and Finishing the surface with out any undulation, voids. Window jams, Corners of wall and floor, ceiling is to be neatly finished as directed by Engineer-in-charge.
Providing and fixing of classic system Blackout fabric Roller Blinds which should be made up of 100% Polyester with Acrylic coating resistant to cracking and fraying. It should have 100% blackout rate. The fabric should be min.0.52mm(±5%) and having min. weight 358g/sqmtr(±5%). Light Fastness ≥6. Can be installed On Face / Ceiling Mount / On Frame /in Recess. The Fixing Brackets are made by steel with powder coating to give greater finish. Brackets shall be accommodating overhead or side mounting with clutch assembly on either end of the blind. The ROLLERTUBE shall be of extruded by non rusting Aluminum alloy with 1.25mm thickness, with anodized for long life, to be available in 32-40mm dia metre for small and big blinds respectively. Aluminium bottom bar with powder coating of 55 microns of approved colour. Wall thickness: 1mm. Width 15mm, Height 30mm, Weight of 300gm /rmtr (+-5%). For a perfect fall of fabric to avoid warpage /floating. Installation to be insert type with end caps to give a neat look. Operating Chain with plastic /steel ball chain (or as permanufacturer's standard) adoptable to the clutch pitch for smooth, quiet lifting & lowering of blind. The blind can be stopped in desired position with the help of stop lock used for raising or lowering action of the shades. The work includes fixing wood sheet and wrapping with blind fabric for the longer windows. The fixing arrangements as per manufacturer’s specification all complete as directed by Engineer-in-charge. (Area shall be measured width as blind width and height from roller top to bottom of bottom-bar).
Fixing only glazing With available float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm), in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket, cleaning the ex etc. complete as per the architectural drawings and the directions of Engineer-in-charge . Note: Glazing clips, cleat angles shall be measured in aluminium items for payment, EPDM rubber / neoprene gasket and screws will not be paid .
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand)
Supplying, fabricating and fixing powder coated aluminium (Min. thickness of powder coating 50 microns) work for partitions and ventilators, with extruded built up standard tubular sections / appropriate Z or other sections of approved make conforming to designation 63400 of IS 1285 and IS 733 including fasteners, EPDM rubber / neoprene gasket, snap beading for glazing / panelling, clips, cleat angle, C.P. brass / stainless steel screws etc., all complete as directed by the Engineer-in-Charge. Note: Glazing clips, cleat angles shall be measured in aluminium items for payment, EPDM rubber / neoprene gasket and screws will not be paid .
Providing and fixing aluminium work for Three/four track sliding window with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required Powder coated aluminium (minimum thickness of power coating 50 micron all complete as per architectural drawings and the directions of Engineer-in-charge. Note: Glazing clips, cleat angles shall be measured in aluminium items for payment, EPDM rubber / neoprene gasket and screws will not be paid .
Supplying and fixing SS Wire mesh of average width of aperture 1.4mm(Approx) and nominal dia of wire 0.63mm(Approx) in aluminium windows neatly all complete as directed by Engineer-in-charge. (Basic price =260.00+10% Contractor Profit+GST 18% = 260.00x1.1x1.18 =337.48)
Providing and fixing glazing With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm), in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . Note: Beadings / glazing clips shall be measured in aluminium items for payment.
Providing and fixing 12 mm thick prelaminated particle board with decorative lamination on both sides flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. Note: Glazing clips, cleat angles shall be measured in aluminium items for payment, EPDM rubber / neoprene gasket and screws will not be paid .
Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
Providing and fixing aluminium hanging floor door stopper (Single rubber stopper), ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.
Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in-charge.
Providing and fixing 12 mm thick frameless toughened glass door shutter, including providing and fixing top & bottom pivot & spring type fixing arrangement, SS Door handle not less than 300 mm, suitable lock and stopper etc, fittings with Dorma, Ozone or HAL approved brand and manufacture, and making necessary holes for fixing required door fittings, all complete and as per direction of Engineer-in-charge.
Demolishing brick work / block work in cement mortar, manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.
Providing, applying and laying cement mortar (1:4) plastering 15 mm thick on brick/concrete surfaces, finished even and smooth with trowel for internal walls etc., with necesary materials, labour, scaffolding, curing, tools and tackles etc., at all heights, all complete as directed by the Engineer-in-Charge.
Painting external surfaces of walls with two coats of low VOC premium weather proof exterior acrylic emulsion paint of approved make, colour, shade, tint & pattern at all levels, over a coat of approved acrylic primer including preparing the surface by removing loose dirt and any organic growth, filling of cracks with white cement putty or Plaster of Paris, necessary scaffolding etc., all complete as directed by the Engineer-in-Charge. Note: The paint shall have anti-algal, anti-fungal, UV resistant & anti-tarnishing qualities with 100% acrylic base and silicon or elastomeric additives.
Painting old plastered interior surfaces with two coats of low VOC less than 50grams / litre, premium plastic emulsion with acrylic base conforming to IS 15489, of approved make, colour, shade, tint & pattern at all levels, over a coat of approved alkali resistant primer including preparing the surface by removing loose dirt and any organic growth, smoothening the surface by using suitable emery paper, filling crevices and finishing even with white cement putty or Plaster of Paris, necessary scaffolding etc., all complete as directed by the Engineer-in-Charge.
Supplying and Painting with synthetic enamel paint of approved brand and manufacture of required colour on old wooden surfaces to give an even shade including preperation of surfaces and filling the crevises, etc., all complete as directed by the Engineer-in-Charge.
Dismantling aluminium partitions, doors (wood or steel), windows, fixed glazing and false ceiling, re-fixing wherever if required, including disposal of unserviceable material and tacking of serviceable material and shutter including chowkhats, architrave, holdfasts etc.with in 50 meters lead as directed by Engineer-in-charge.
Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm (approx).
Dismantling W.C.Pan / Urinal of all sizes including disposal of dismantled materials including malba all complete as per directions of EIC
Providing and laying Vitrified tiles in floor with sizes of 600mm x 600mm (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints
Making chases upto 7.5x7.5cm in walls including making good and finishing with matching surface after G.I pipe etc
Dismantling 15 to 40 mm dia G.I.Pipe including stacking of dismantled pipes (within 50meters lead) as per direction of EIC
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) concealed Pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints cutting chases and making good the walls etc. complete as per direction of EIC
15 mm dia
20 mm dia
25 mm dia
Providing and fixing on 75 mm bend wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. as directed by the Engineer-in-Charge
Providing and fixing on Single tee with door 110x110x110 mm wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. as directed by the Engineer-in-Charge
Providing and fixing on Single tee with door 75x75x75 mm wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. as directed by the Engineer-in-Charge
Providing and fixing white vitreous china pedestal type EWC pan with ISI marked white solid plastic seat and lid (Europen type W.C.pan) with seat and lid, 10litre low level white P.V.C flushing cistern, including flush pipe,with manually controlled device (handle lever), confirming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. all complete as directed by the Engineer-in-Charge.
Providing and fixing 8mm dia C.P. / S.S Jet /Health Faucet with flexible tube upto 1metre long with S.S. triangular plate for Eureopean type W.C of quality and make as approved. all complete as directed by the Engineer-in-Charge.
Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. 610 x 390 x 370 mm having pre & post flushing with water(250ml & 500 ml approximate consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufactures spectification and direction of EIC.
Providing and fixing stainless steel A ISI 304 (18/8) Kitchen sink without drain board - 610x460 mm bowl depth 200mm as per IS:13983 with C.I. brackets and stainless steel plug 40mm,including painting of fittings and brackets, cutting and making good the walls wheever required, all complete as directed by the Engineer-in-Charge.
Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS:8931, and all complete as directed by the Engineer-in-Charge.
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels, as directed by the Engineer-in-Charge.
Supplying, jointing, testing and commissioning, approved make 20mm dia GM body gate valves with screwed ends etc. complete all as directed by the Engineer-in-Charge.
Supplying, jointing, testing and commissioning, approved make 15mm dia Stop cock etc. complete all as directed by the Engineer-in-Charge.
Supplying, fixing, testing and commissioning 75mm dia PVC pipes conforming to IS : 13592 Type B and of approved make with rubber ring joints conforming to IS 5382, jointed together with solvent, on walls, including all necessary clamps, pipe cutting and wastages, cutting and making good the walls, connecting to existing lines etc., all complete as directed by the Engineer-in-Charge.
Providing and fixing flexible 32mm dia P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete etc., all complete as directed by the Engineer-in-Charge.
Providing and fixing 600 x 450 mm beveed edge mirrior of superior glass (of approved quailty) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
Providing and fixing PTMT Towel Ring Circular shape minimum 200mm dia or Trapezoidal shape 215mm long, 200mm wide with minimum distances of 37mm from wall face with concealed fittings arrangement of approved quailty and colour, weighing not less than 88 gms. all complete as directed by the Engineer-in-Charge.
Providing and fixing toilet paper holder C.P.Brass , including screws & fittings etc., as directed by the Engineer-in-Charge.
Providing and fixing PTMT Towel rail complete with brackets fixed to wooden cleats with CP brass screws, 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms, with concealed fittings arrangement of approved quality and colour including screws & fittings etc., as directed by the Engineer-in-Charge.
Providing and fixing PTMT liquid soap container 109 mm wide, 125mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms including screws & fittings etc., as directed by the Engineer-in-Charge.
Providing and fixing White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require, as directed by the Engineer-in-Charge.
Providing and fixing uplasticised PVC connection pipe, 15mm dia and 450mm long, with brass unions etc., all complete as directed by the Engineer-in-Charge.
Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.
Providing and laying ceramic floor tiles of size 300x300mm(Thickness to be specified by manufacture) of first quality confirming to Is:15622 of approved make in colours ,laid on 20mm thick cement mortar 1:4(1cement :4course sand),jointing with grey cement [email protected]/sqm including pointing the joints with white cement and matching pigment etc.
Total (Exclusive of GST)
Percentage above or below for total value on Sl.No. 48
Total amount after Percentage Sl.No. 48 + Sl.No. 49
GST @ 18% for total value on Sl.No. 50
Total amount (Inclusive of GST) Sl.No. 50 + Sl.No. 51
Preamble: 1. The subject work has been called on works contract basis and prevailing GST for same is 18%. Any change in GST +/- during the currency of contract shall be on HAL account. The Tenderer shall abide by prevailing GST act. 2. L1 (lowest quote) will be determined based on the total quoted amount including GST. 3. This BOQ specification has to be read in conjunction with detailed technical specification and tender drawings if any. 4. Please refer Tender document carefully and understand full scope of work, Terms and conditons, if required visit the site and then submit your quote as no clarification will be entertained later on account of ignorance of the work/site.
Pre-Qualification Profile (To be Uploaded along with Part - A)
Contract Number:
Name of the individual/ Firm/ Company:
Estimation Amount In Rs:
Tender Notice Date:
GST ID No. For HAL
Name of the individual/ Firm/ Company: *Mandatory
Type of ownership
If Other, please specify
Details of Constitution or Legal Status such as certificate of Incorporation, shops and establishments, Contractor registration
Address for Correspondence
Contact Details
Contact Person Name
Designation
Mobile no
Ph. No with STD Code
FAX. No with STD Code
Email Id
Registered Contractor
If Registered Contractor with HAL YES/NO
Registration No
Category
PEMD amount (if paid)
I.T Returns for past 03 Years (Assessment Years)
Average Annual Financial Turnover during the last 3 years, ending 31st March 2023 of the previous financial year[should not be less than 30% of Amount put to tender]
ESI & PF Nos. with proof
ESI Registration No. with proof [Mandatory]
PF Registration No. with proof [Mandatory]
Bank(s) details: [Copy of the cheque leaf to be uploaded]
Bank Account No.
Name of the Bank
Type of Account
Branch, Place
Bank Code No.
MICR No.
ECS No.
IFS Code No.
Latest Bankers Solvency certificate from any Nationalized /Scheduled Bank issued NOT before 12 months from the last date of Tender submission .
Name of the Bank & Branch
Date of issue
Value in Rs.
Solvency Value is as per NIT
Experience of having successfully completed similar works during last 7 years ending last day of previous month [ Latest work experience certificate may be uploaded] (i) Three similar completed works each costing not less than an amount equal to 40% of estimated cost. (ii) Two similar completed works each costing not less than an amount equal to 50% estimated cost. (iii) One similar completed work costing not less than an amount equal to 80% estimated cost.
Completed similar works during last 7 years
Work No I
Brief Description of Work
Completed value of Work in Rs.
Date of Commencement of Work:
Date of Actual Completion of work:
Work No II
Brief Description of Work:
Completed value of Work in Rs.
Date of Commencement of Work:
Date of Actual Completion of Work:
Work No III
Brief Description of Work:
Completed value of work in Rs.
Date of Commencement of Work:
Date of Actual Completion of Work:
Details of person holding the Power of Attorney ( if different from the contact person)
Designation
Mobile no
Ph. No with STD Code
FAX. No with STD Code
Email Id
Documents Need to Uploaded
IT Return, Profit & loss and Balance Statement for the Financial Year duly mentioned above certified by the Chartered Accountant.
DECLARATION I
The document being viewed / downloaded from the website and having read & understood all the contents of the tender document mentioned under terms and conditions Including price bid do here by accept all the terms and conditions laid doen In the said Tender document and will abide by the same on acceptance and ward of work.
DECLARATION II
I/We declare and confirm that - 1. All Information and attachments submitted along with this offer are true and correct. 2. I/We are aware that any false Information provided herein will result In the rejection of my offer. 3. I/We shall not make refund claims of expenditure incurred in processing this offer. 4. I/We aware that document sought only be uploaded for evaluation of offer.
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
raw.json
RAW_JSON
07_NIT_UPGRADATION_OF_RECEPTIONS.pdf
TENDER_DOCUMENT • 0.09 MB
07_TD_UPGRADATION_OF_RECEPTIONS.pdf
TENDER_DOCUMENT • 1.72 MB
07_PQ_UPGRADATION_OF_RECEPTIONS.pdf
TENDER_DOCUMENT • 0.01 MB
07_PB_UPGRADATION_OF_RECEPTIONS.pdf
TENDER_DOCUMENT • 0.28 MB
07_PB_UPGRADATION_OF_RECEPTIONS_BID.xlsm
TENDER_DOCUMENT • 0.10 MB
07_PQ_UPGRADATION_OF_RECEPTIONS_BID.xlsm
TENDER_DOCUMENT • 0.01 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .