SPECIAL REPAIR TO UNDER GROUND SUMP IN MES AREA AT AIR FORCE STATION JAIPUR

Amount

Demolition of cement concrete reinforced (reinforcement cut as required to facilitate demolition) roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and as directed.

Taking down cement plaster on old brick or stone walls , including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and as directed.

M&L for formwork to soffits of suspended slabs such as flat roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

M&L for formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide. (Where RCC/PCC band in walls, spanning and opening, the formwork soffit only) complete all as specified and as directed.

M&L formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and as directed.

M&L for reinforced cement concrete (design mix M-30) 20mm graded aggregates in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for reinforced cement concrete (design mix M-30) 20mm graded aggregates in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for reinforced cement concrete (design mix M-30) 20mm graded aggregates in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and as directed.

M&L for mild steel TMT bars of 10 mm dia and above, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars of 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified and directed.

M&L for 100mm thick plain cement concrete type B1 1:2:4 (20 mm graded aggregate) in sub base/floor finishes complete all as specified and as directed.

M&L for setting coat 3mm thick, trowelled to even and smooth finish in CM 1:2 over and including 10mm thick screed bed or bedding layer in cement mortar 1:3 fair finished using WPC @ 3 % by weight of cement or manufacturer's instruction complete all as specified and directed. (Note :- WPC shall be measured and paid seperately).

M&L for setting coat 3mm thick, trowelled to even and smooth finish in CM 1:2 over and including 10mm thick plastering in cement mortar 1:3 on internal brick walls using WPC @ 3 % by weight of cement or manufacturer's instruction complete all as specified and directed. (Note :- WPC shall be measured and paid seperately).

M&L for setting coat 3mm thick, trowelled to even and smooth finish in CM 1:2 complete all as specified and directed.

M&L for 10mm thick rendering on external brick work in cement mortar (1:4) finished the surface even and fair complete all as specified and directed.

M&L for 10mm thick rendering on roof slab in cement mortar (1:4) finished the surface even and fair complete all as specified and directed.

M&L for 5mm thick rendering on roof ceiling in cement mortar (1:3) finished the surface even and fair complete all as specified and directed.

Supply only integral water proofing compound all as specified and directed.

M&L for preparing newly plastered surfaces of wall and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

M&L for preparing newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for three coats of white wash on new ceiling surfaces including preparation of surfaces complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-410-W. Gde-E-250 complete all as specified and directed.

M&L for two coats of synthetic enamel paint over & including a coat of red oxide and zinc chrome primer including preparation of new steel surface over 10cm width or grith upto and including 12 meter height complete all as specified and directed.

S&F Mild steel, plain, black sheet of thickness 1.6mm in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc as required complete all as specified and directed.

Demolition of brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed.

M&L for brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:6) complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for 100 mm thick PCC type C-2, 1:3:6 using 40 mm graded stone aggregate as in plinth protection/ floors for levelling concrete complete all as specified and as direcetd.

M&L for plain cement concrete type B-0, 1:2:4 using 12.5 mm graded stone aggregate as in coping, benching etc including necessary form work complete all as specified and directed.

Taking up or down DI pipe and connections including cleaning for refixing or removal to store of 100 mm bore complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store of 50 mm bore complete all as specified and directed.

Taking down Gate valve of 50 mm size and removal to store complete all as specified and directed.

Taking down Sluice valve of 100 mm size and removal to store complete all as specified and directed.

S&F galvanised steel water tubing (GI pipe), medium grade with all fittings and fixed to wall, floor and ceiling of 50mm bore complete all as specified and as directed.

Supplying, laying, jointing & testing in trenches ductile iron pipe of 100mm boreincluding specials with spigot and socketed ends class k9, conforming to IS 8392-2000 complete all as specified and directed.

Supply, fixing, jointing and testing, ISI Marked, of approved quality, gun metal globe/gate valve of 50mm size with iron wheel head, both ends screwed for iron pipe complete all as specified and directed.

Supply, installation, fixing, jointing and testing, ISI Marked, of approved quality, cast iron sluice valve of 100mm bore of class PN-1.6 conforming to IS-14846 of 2000 both ends flanged with iron wheel head and stainless steel spindle, long body type, jointed and tested complete all as specified and directed.

Supply only Heavy Duty 3.8 Meter/12.5 Feet Multi-Purpose Aluminum Telescopic Extension Step Ladder having 13 Steps, black anti-slip rubber sleeve on bottom of ladder step and stable locking key between two neighboring steps to avoid friction complete all as directed.

M.S. ENTERPRISES

LAKSHMI ASSOCIATES