REPAIR/MAINT OF SPRINKLERS, FLUSHING OF BOREWELL, REPLACEMENT OF U/S FOUNTAIN WITH CONNECTED FIRE HYDRANT SUPPLY DISTRIBUTION CONNECTED ITEMS AT AF STN BHISIANA

Amount

S&F in replacement of single channel four pipe Laser Aspiration detection unit . The unit should be UL and VDS approved complete with display of all alarm dual filter on board 20000 event log memory worth RS 232 port . The device should support minimum 100 m pipe for each channel and sensivity of 01%m complete all as specified and directed by Engineer in Charge. (P4)

S&F in replacement of repeater panel having display system of existing make and model suitable to incorporate in existing system having LOOP: Fire Red Lamp ON, Open Amber Lamp ON, Short Amber Lamp ON, Isolate Amber Lamp ON Monitor Mains ON 230VDC, Earth Line fault, BAT, low , BAT Discharge, CPU RUN-Processor working Controls: Lamp Test-Healthiness of lamp, Silence -tomute sounders Evacuate-evacuate the building, Re set - To restore system. Contractor shall visit each repeater panel prior quoting the rate to know the current status of respective Panel No claim on whatsoever account shall be entertained during current of work complete all as specified and directed by Engineer in Charge. (P4)

S&F in replacement of ECO sensor for CO monitoring suitable to existing make and model suitable to incorporate in existing system Contractor shall visit each sensor prior quoting the rate to know the current status of respective sensor mechanism No claim on whatsoever account shall be entertained during current of work complete all as specified and directed by Engineer in Charge (P4).

Comprehensive maintenance of Microprocessor based panel 1 loop analogue addressble type fire alarm control panel with 80 character CD diaplay with battery backup of 11/2 hours access 500 events histrocial logging having loop Free red lamp on , Open Amber lamp ON, Short - Amber lamp On , Isolate - Amber Lamp On, Control : Lamp test-LED Healthy, Sielence - TO stop alarm, Evacuate - fire alarm ON, Reset-to Restore system, Monitor : mains ON-230 VAC, BAT ON-system at BAt, System ON -24 VDC, Xharger ON 27.3 VDC, Fire sounser ON, Silence - MUTE/ACK, Earth - Line Fault , BAT LOW -Bat Below 22 V. (P4) Note The Contractor Shall be responsible to replace all spare parts minor/major required to serviceabe of panel , Nothing will be paid to extra during contract period, If he fail to rectify within 24 Hrs Recovery @ 1000 per day wiil be made in RAR/final Bill.

S&F in replacement power supply units comprising of battery backup for 11/2 hours charging units , MCB DB and necessary MCB -power supply unit should have capacity to operate on 230 volt AC main input & provide 24 to 30 volts DC output for powering up The unit shall also supports battery backup in ase of AC main failure and should have built in charging circuit to batttery.suitable to existing make and model suitable to incorporate in existing system . Contractor shall visit each supply unit prior quoting the rate to know the current status of respective supply unit mechanism No claim on whatsoever account shall be entertained during current of work complete all as specified and directed by Engineer in Charge. (P 4)

S&F in replacement of analoge addressable photoe electric smoke detector with mounting based LED , address switch to programme the detector from 01-99 with BASE complete as required programme the detector rom 01-99 with BASE complete as required the contractor shall visit each photo electric smoke detector unit prior quoting the rate to know the current status of respective photo electric smoke detector mechanism No claim on whatsoever account shall be entertained during current of work complete all as specified and directed by Engineer in Charge.

S&F in replacement of addressable hooter with strobe for alaram annunciation along with all required accessories (Weathr proof all as specified and as directed by Engr-in-charge existing make and model suitable to incorporate in existing system. Note (a) The contractor shall check make and model before quoting of tender and inspect hooter unit prior quoting the rate to know the current status of respective hooter mechanism. (b) No claim on whatsoever account shall be entertained during current of work complete all as specified and directed by Engineer in Charge.

S&F in replacement addressable manual call point complete as per OEM specification (weather proof ) The item should be suitable to incorporate in existing system. (Alpha Hanger) Note (a) The contractor shall check make and model before quoting of tender and inspect photo hooter unit prior quoting the rate to know the current status of respective hooter mechanism. (b) No claim on whatsoever account shall be entertained during current of work complete all as specified and directed by Engineer in Charge.

Takng down U/S & S&F addressable control module for Hooter complete as required as per OEM specification and suitable to existing make and model suitable to incorporate in existing system . Note (a) The contractor shall check make and model before quoting of tender and inspect photo hooter unit prior quoting the rate to know the current status of respective hooter mechanism. (b) No claim on whatsoever account shall be entertained during current of work complete all as specified and directed by Engineer in Charge.

Taking down U/S & S&F of aspiration system address switch to programme the monitor modules from 01-09 complete as per OEM specification suitao ble existing make and model suitable to incorporate in existing system. Note (a) The contractor shall check make and model before quoting of tender and inspect monitor modules unit prior quoting the rate to know the current status of respective hooter mechanism. (b) No claim on whatsoever account shall be entertained during current of work complete all as specified and directed by Engineer in Charge.

Taking down U/S & S& F cable copper 03 core x 1 sqmm for power -24 AWG stranded (7x32) tinned coppper conductor in suitable PVC conduit existing make and model suitable to incorporate in existing system . Note: The contractor shall inspect make and model before quoting of tender

Supply and Laying in replacement of , LT UG XLPE insulated 1100 volt grade heavy duty electric cables with aluminium conductor , cross sectional area 35 sqmm 3.5 core all as specified and directed The cost shall be included suitable size of steel gland , thimbles ,lugs required to jointing of cableall as specified and directed by Engr-in-charge (From panel to AHU)

Supply and Laying in replacement of , LT UG XLPE insulated 1100 volt grade heavy duty electric cables with aluminium conductor , cross sectional area 150 sqmm 3.5 core all as specified and directed The cost shall be included suitable size of steel gland , thimbles ,lugs required to jointing of cableall as specified and directed by Engr-in-charge (From panel to AHU)

Material & labour for replacement of Landing valve 63 mm including jointing with rubber insertion 3 mm thick bolts, nuts and washers etc complete all as specified and directed by Engr-in-Charge. (Bravo)

Material & Labour for replacement of RRL hose ISI marked with both coupling dia 63mm in 15mtr length complete all as specified and directed by Engr-in-Charge. (Alpha & Bravo)

Material & Labour for replacement of Hose reel drum with RRL hose ISI marked with both coupling dia 63mm in 30mtr length. Make Life Guard, OMEX or equivalent. (Alpha & Bravo)

S&F in replacement 19mm dia rubber braided hose of 36 mtr length with gate valve and shut of nozzle with working pressure of 12 bar and minimum flow rate 285 OM fixed in existing Hose reel drum of dia 565mm dia cast manual swinging type as complete. (Alpha & Bravo)

Taking down U/S & S&F in replacement Weather proof cabinet of size 900 x 600x 450mm made out of MS sheet 16 gauge having central opening and 4mm thick glass doors (2 Nos) suitably marked on the outside With Letters 'FIRE HOSE' cabinet with necessary locking arrangement including all fasterns etc and shutter shall be powder coated with signal red colour,shutter with frame fabricated all as specified and directed. Note: The hose cabinet will be fixed PCC Platform near the Fire Hydrant and cost of PCC flatform and fixing is deemed to be included in quoted cost.

S&F in replacement Gun metal Air Release Valve 15/20 mm on wet riser, with shut off Forge Brass ball valve complete all as specified and directed by Engineer in charge. (Alpha & Bravo)

S&F in replacement Female/Male Coupling with Blank Caps/Plugs of 63 mm of working pressure 10.5 Kg/Sqcm of Gun metal/Brass complete all as specified and directed by Engineer in charge. (Alpha & Bravo)

S&F in replacement flanged & shore connection of 63 mm outlet of material Gun metal/Stainless Steel with nuts, bolts washer etc complete all as specified and directed by Engineer in charge. (Alpha & Bravo)

S&F of in repair glass of fire hydrant boxes of size 60x60 mm incl rubber gasket/seal complete all as specified and directed by Engr-in-Charge. (Charlie)

S&F in replacement basket type simple stainer of CS/CI body with SS strainer element 40 mesh matching flange including nut & Bolts , gaskets suianle for flow 136 cum /hr at pressure of drop not more than 0.2 kg /cm2 at 50% chocked condition, body hydroest at 16.0 kg /cm 2 for suction for fire fighting of size 150 mm bore.

S&F in replacement Ý' type statainer of CS/CI body with ss strainer element 40 mesh matching flange nut bolt, gasket etc suitable for flow of 136 cum/Hr at pressure of drop not more than 0.2 kg/cm 2 at 50% chocked condition , body hdrotest at 16 kg/cm2 for suction suitable for fire fighting of size 100 mm with suitable material complete all as specified and as directed by Engr-in-charge

M&L for cleaning of strainer all type and any size including dismantling and cleaning using Fernox DS-3 cleaner chemical or OEM recommendation and refixing of the same complete all as specified and as directed by Engr-in-charge

M&L for painting of fire hydrant stand post end flanged 1.5 mtr height with one end bend to 90 degree suitable for double fire hydrant valvesncluding 1 No CI duck foot bend 80 mm double end flanged and 1 no 80 mm 63mm reducer and 1 no 80 mm dia CI buerfly valve complete after removing all dust, dirt etc and clean the surface thoroughly with two coats of synthetic enamel paint including writing the complete all as specified and directed.

M&L for descaling and servicing the radiator of Diesel engine 62-73 BHP Cap internally and externally by using chemicals, including soldering the copper tubes and tank etc for arresting leakage complete all as specified and directed.

M&L for descaling and servicing the radiator of Diesel engine 43/52 BHP Cap internally and externally by using chemicals, including soldering the copper tubes and tank etc for arresting leakage complete all as specified and directed.

Material and labour for Drain the out lived engine oil, clean the oil tank and filling the new engine oil grade 20W 40 as required, complete all as specified and as directed.

Supply and filling coolent, complete all as specified and as directed.

M&L for Repairing the self Dynamo 12 Volts after removing from diesel engine set of any capacity and transporting to an authorised sevice centre complete all as specified and directed.

Taking out old U/S and Supply and fix CI body Sluice valve PN 1.6 conforming to IS of size 150 dia complete with nuts,bolts,rubber gaskets etc including ,ISI marked ,including jointing material such as rubber gasket,bolts,nuts,etc suitable for size 150 mm complete all as specified and as directed by Engr-in-charge

Taking out old U/S and Supply and fix CI body Sluice valve PN 1.6 conforming to IS of size 100 dia complete with nuts,bolts,rubber gaskets etc including, including jointing material such as rubber gasket,bolts,nuts,etc suitable for size 100 mm complete all as specified and as directed by Engr-in-charge

Taking out old U/S and Supply and fix CI body Sluice valve PN 1.6 conforming to IS of size 80 dia complete with nuts,bolts,rubber gaskets etc including, including jointing material such as rubber gasket,bolts,nuts,etc suitable for size 80 mm complete all as specified and as directed by Engr-in-charge

Taking out old U/S and Supply and fix CI body Sluice valve PN 1.6 conforming to IS of size 50 dia complete with nuts,bolts,rubber gaskets etc including, including jointing material such as rubber gasket,bolts,nuts,etc suitable for size 50 mm complete all as specified and as directed by Engr-in-charge

Taking out old U/S and Supply and fix CI body NRV valve conforming to IS of size 150 dia complete with nuts,bolts,rubber gaskets etc including, including jointing material such as rubber gasket,bolts,nuts,etc suitable for size complete all as specified and as directed by Engr-in-charge

Taking out old U/S and Supply and fix CI body NRV valve conforming to IS of size 100 dia complete with nuts,bolts,rubber gaskets etc including ,including jointing material such as rubber gasket,bolts,nuts,etc suitable for size complete all as specified and as directed by Engr-in-charge

Taking out old U/S and Supply and fix CI body NRV valve conforming to IS of size 50 dia complete with nuts,bolts,rubber gaskets etc including ,including jointing material such as rubber gasket,bolts,nuts,etc suitable for size complete all as specified and as directed by Engr-in-charge

Taking out U/S battery cell 7 Supply and fix New battery cell 12 V 7 AH , Charging voltage ; Stand by 13.5 V Cyclic : 14.7 V 0f make Amaron/Exide/ Luminoous, complete all as specified and as directed by Engr-in-charge

S&F in replacement of GI pipe and fix MS ERW pipe nominal dia 100 mm as per IS 3589 (1981) thickness 5.0 mm , including special joints complete for delivery and side including necessary nuts bolts and rubber etc, complete with one coat of red oxide and two coat of black paint on ms pipe complete all as specified and as directed by Engr-in-charge. Note The cost shall be inclusive for making suction/delivery pipe from existing pipe from pump to SWT pipe line for delivery including welding , bending work .,socket, union , bend etc, bend

S&F in replacement of GI pip and fix MS ERW pipe nominal dia 80 mm as per IS 3589 (1981) thickness 5.0 mm , including special joints complete for delivery and side including necessary nuts bolts and rubber etc, complete with one coat of red oxide and two coat of black paint on ms pipe all as specified and as directed. Note: - The cost shall be inclusive for making suction pipe from existing pump to SWT for connection of varios sizes of DI/GI pipe line for delivery including welding , bending work .

Taking down U/S & Supply and fix CI body foot valve ISI marked of size 150 dia complete with nuts,bolts,rubber gaskets jointing material suitable for size 150 mm complete all as specified and as directed by Engr-in-charge

Taking down U/S & Supply and fix CI body foot valve ISI marked of size 80 dia complete with nuts,bolts,rubber gaskets jointing material suitable for size 80 mm complete all as specified and as directed by Engr-in-charge

Taking down U/S & Supply and fix CI body foot valve ISI marked of size 100 dia complete with nuts,bolts,rubber gaskets jointing material suitable for size 80 mm complete all as specified and as directed by Eng-in-Charge

S&F in replacement of CI spun pipe Centrifugally Cast Iron "LA" 150mm dia spigot and socketed ends suitable for lead joints in trenches complete all as specified and directed.

S&F in replacemnt of CI spun pipe Centrifugally Cast Iron "LA" 100mm dia spigot and socketed ends suitable for lead joints in trenches complete all as specified and directed.

S&F in replacemnt of ductile iron pipe SS including specials , Class K-7" , 150 mm dia all as specified and as directed rate are ncluding special joints such as lead/ tyton complete for delivery and side including necessary nuts bolts and rubber etc, complete all as specified and as directed by Engr-in-charge

M&L for run lead joints for 150mm dia spigot and socketed CI pipe fittings including spun yarn etc. complete all as specified and as directed by Engr-in-charge

M&L for run lead joints for 100mm dia spigot and socketed CI pipe fittings including spun yarn etc complete all as specified and as directed by Engr-in-charge

M&L for run lead joints for 80mm dia spigot and socketed CI pipe fittings including spun yarn etc. complete all as specified and as directed by Engr-in-charge

Dismantling the Electric Induction Motor / submersible motor AC, 3 Phase, 415 Volts from the foundation/ Blast pen SWT of depth of 5-10 mtr by disconnection of Cable and coupling connection of Pump and shifting to the Civil Workshop for the following repir/ replacement work complete all as specified and directed by Engr-in-Charge:- (a) Re-winding the motor with supper enameld copper winding wire having suitable size copper wire with proper insulation including varnishing, heating complete. capacity of 7.5 HP (b) Replacement of ball bearing NBC or as per exsting make/ model with providing of high grade grease. (c) Re- assembling the complete motor and shifting to the same to its existing location and re-connection all cable and coupling and testing the same on load all as directed by Engr-in-Charge. (BP-6-10)

All as per item No. 51 above but having 10 HP capacity submersible motor complete all as directed by Engineer in Charge.

All as per item No. 51 above but having 20 HP capacity motor complete all as directed by Engineer in Charge.

All as per item No. 51 above but having 40 HP capacity motor complete all as directed by Engineer in Charge.

S&F in replacement of CI fittings bend (any type, radius and angle) tapers any type (straight, bend, increasing, decreasing or double socket) etc Tee pieces single branch "Y" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs of size upto 150mm complete all as specified and directed.

S&F in replacement of Gun metal globe or gate valve (ISI marked), with iron wheel head, screwed both ends, suitable for 50 mm bore iron pipe and fixed including testing complete all as specifed and directed by Engr-in-Charge.

All as per item No. 56 above but having size 40 mm dia bore complete all as specifed and directed by Engr-in-Charge.

All as per item No. 56 above but having size 25 mm dia bore complete all as specifed and directed by Engr-in-Charge.

S&F in replacement of Rubber coupling TC-16/TC-14 suitable for 40 HP Centrifugal pump complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Rubber coupling as per sample suitable for 20 HP Centrifugal pump complete all as specifed and directed by Engr-in-Charge.

S&F in replacement Contactor 32A , 415 VAC, 50 Hz complete as per existing Make & Type all as specifed and directed by Engr-in-Charge.

S&F in replacement Single Phase Preventor (VSP 3), 415 VAC, 50 Hz complete as per existing sample Sr No.-7W0609 Make- Minilec complete all as specifed and directed by Engr-in-Charge.

S&F in replacement Contactor 150A , 415 VAC, 50 Hz complete as per existing Make HPL complete all as specifed and directed by Engr-in-Charge.

S&F in replacement Thermal over load relay 9- 32 A, 415 V, 50 Hz as per existing Make & Type complete all as specifed and directed by Engr-in-Charge.

S&F in replacement of Electronic timer Star-Delta of 3S-120 Second as complete all as specifed and directed by Engr-in-Charge.

S&F in repairs MCCBs 400 Amps, 4 Pole having rupturing capacity 36KA, 415 volts including termination point for connection complete all as specified and directed.

S&F in repairs MCCBs 250 Amps, 4 Pole having rupturing capacity 25KA, 415 Volts including termination point for connection complete all as specifed and directed by Engr-in-Charge.

S&F in repairs MCCBs 100 Amps, 4 Pole having rupturing capacity 16KA, 415 volts including termination point for connection complete all as specifed and directed by Engr-in-Charge.

S&F in repairs MCCBs 63 Amps, 4 Pole having rupturing capacity 16KA, 415 volts including termination point for connectioncomplete all as specifed and directed by Engr-in-Charge.

Dismantling/taking down the centrifugal pump set of capacity 40 HP from foundation after disconnecting of discharge, suction and induction motor connection and shifting to the same to Civil Workshop at Bathinda for the following repair :- (a) Dismantling the complete pump and taken out main shaft and impeller from the pump by disconnection of all nuts, bolts and washers and minor repair and balancing of main shaft and impeller by necessary lathe and machine work and replacement with complete new gasket and mild steel nut, bolt , check nut and washer complete all as directed. (b) Replacement of ball bearing NBC 6312 including providing of required grease complte 02 Nos. (c) Re-assembling the complete and fixing at site and connection of suction, discharge and the induction motor and testing the same on full load complete all as specifed and directed by Engr-in-Charge.

All as above but 20 HP capacity of pump complete all as specifed and directed by Engr-in-Charge.

All as above but 10/7.5 HP capacity of pump complete all as specifed and directed by Engr-in-Charge.

M&L for repairs to UNSV star delta starter for pump set 20 HP by replacing terminal overload relay, coil of any other parts required for proper functioning of pump sets complete all as specifed and directed by Engr-in-Charge.

M&L for replacement to UNSV star delta starter for pump set 10 HP by replacing terminal overload relay, coil of any other parts required for proper functioning of pump sets complete all as specifed and directed by Engr-in-Charge.

M&L for replacement of Pump motor coupling fully suitable for 40 HP pump with rubber bushes complete all as specifed and directed by Engr-in-Charge.

M&L for replacement of Pump motor coupling fully suitable for 20/10 HP pump with rubber bushes complete all as specifed and directed by Engr-in-Charge.

M&L for replacement of gland flange made of steel suitable for 5 to 40 HP monoblock pump set including replacement of gland packing all as directed.

M&L for replacement of UNSV rubber insertion packing suitable for 200mm CI foot valve/suction pipe flanged incl replacement of UNSV nut and bolts.

M&L for prepration of old painted surface of Fire Hose Cabinet of any size by scratching /rubbing down the old paint by wire brush or emery paper and applying two coat of Red oxide Paint (weather proof and rust resistant) etc. complete all as specifed and directed by Engr-in-Charge.

M&L for prepration of old painted surface of 40 HP Centrifugal Pump and motor by scratching /rubbing down the old paint by wire brush or emery paper and applying two coat of synthetic enamelecd paint etc. complete all as specified and directed.

M&L for prepration of old painted surface of 10 to 20 HP Centrifugal Pump and motor by scratching /rubbing down the old paint by wire brush or emery paper and applying two coat of synthetic enamelecd paint etc. complete all as specifed and directed by Engr-in-Charge.

Repair/overhauling of Diesel Driven Pump of Capacity 52 BHP installated at Bomb Dump. (a) Dismantling and removing nuts & bolts Electric connections, water connections for the repairs. (b) Dismantling/opening of complete cylindr head assembly rocker arms assembly piston head assembly sleeves by removing nuts & bolts for repairs complete. (c) Servicing Washing of complete engine parts with kerosene oil. (d) Reassembling of complete engine by tightening of nuts and bolts with replacement of the following engine part and testing on full load for 8 hours :- (i) Piston complete. (ii) Sleeve. (iii) Valve Seat. (iv) Guide Valve. (v) Injector. (vi) Gasket Set. (vii) Pump repair complete. (viii) Fuel Filter. (ix) Lubrication oil filter. (x) Air Filter. (xi) Ring Set. (xii) Conneting Rod Bearing. (xiii) Cylinder Head. (xiv) Calibration of Pump. (xv) Head repair. (xvi) CR Brush. (xvii) Main Bearing. (xviii) Timing Seal. (xix) Complete Packing Kit (xx) Water Ring Kit (xxi)Radiator Cleaning. (xxii) Nozzle Pump Set.(Alpha & Bravo)

M&L for servicing of Diesel Engine of 52/60 BHP with replacement of fuel filter any size as per existing - 1 Set, Air filter - Each, Oil/Lubricant Filter - Each, Engine Oil- 10 Ltr, Coolant up to max level, hose pipe as per existing - Set of two, Battery Terminal - Set of Two, Fuel Pipe fuel Tank to Fuel Filter with Clamp-Each and Radiator cleaning complete all as specifed and directed by Engr-in-Charge.

M&L for Repairing the self starter after removing from the Diesel Engine set of capacity 52/60 BHP and transporting to an authorised sevice centre complete all as specified and directed.

M&L for repair to valve pit of size 90x90x90 cm and replacement of valve pit cover with MS cover and including MS sheet cover fabricated from 3 mm thick MS sheet and frame of angle iron 40 x 40 x 6 mm with fixing arrangement, hinges and locking arrangement and painting two coat of synethetic enmel paint over a coat of red oxide primer on MS cover and frame, complete all as specifed and directed by Engr-in-Charge.

M&L for repairs to gate and replacement of spindle suitable for 150mm sluice valve complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Gland Dori suitable for pump set any capacity complete all as specifed and directed by Engr-in-Charge.

S&F in replacement of High Grade Grease for Pump Set and Motor complete all as specifed and directed by Engr-in-Charge.

S&F in replacement of NRVTikki suitable for 150/100 mm bore NRV complete all as specifed and directed by Engr-in-Charge.

M&L for attending complaint day to day like , tightning of nut bolot, finding of leakge in pump any type , cheking of starting of diesel driven pump , checking of battery thimbles, priming work using seprate submersible pump or tanker mounted vehicle for filling of suction/ delivery pipe with water and checking of serviceablity of pump and opening of valve /NRV with nut bolt finding of leakage in sluice/gate valve / NRV removing of air release from pump and operating of pump and checking pump is lifting of water with force or not if not then priming of pump with water and find the fault and rectify the fault of pump , if not lifting of water then replace galnd rope and water seal given in schedule, if battery is found discharge the contractor remove battery from mechanical hydrant pump and transport to workshop for charginf purpose and after full charge of battery the contractor again transport from work shop to pump and install in pump house and start the engine up to satisfaction of Engr-in-charge . The motor of mechanial hydrant pump/ Electrical operated pump any capacity installed at Bravo / Alpha, Charlie P-IV fire hydrant pump house stopping leakege of GI Pipe upto 150 mm dia by replacing any type of (bend, tee, elbow, reducer, end plug, taper, union, nipple, socket etc) all as specified and directed by Engr-in-Charge

M&L for flushing of borewell using DTH machine suitable for bore well with compressor of suitable capacity by drilling bore wells perfectly vertical 150 to 300mm dia in any type of soil / clay / sand / soft rock / hard rock at a locationnear officer mesds GE to the depth not exceeding 100 meters and disposal of waste material using necessary required mechanical equipments complete as specified and directed for number of hours till sand free water (Clean water) is obtained and tested including using necessary required mechanical equipments complete for following duration complete all as specifed and directed by Engr-in-Charge.

Material and labour for conducting yield test of sucessful bore well with suitable capacity of submersible pump set continuously for eight hours for 3 consecutive days complete all as specifed and directed by Engr-in-Charge.

Taking out unserviceable GI pipe from bore well using lifting hydrauclik machine or puller with tripot or any other suitable equipmentto lift pipe from 100 mtr depth borewell and supply and install New GI Pipe Medium grade 100 mm bore pipe as colum pipe in to the bore well including all fittings such as socket , union , flange , bends as colum pipe for bore well including connecting and lowering complete all as specified and directed. The cast shall be included dismatling of submersible pump with motor from GI pipe alongwith power cable and again fixing in new pipe and new power cable given in sch. No extra amount shall be paid to the contractor (Main Pump)

S&F in replacement of unserviceable cable PVC insulated, PVC sheathed, copper conductor, multistranded, submersible cable, 16 sqmm , 03 core, 1100 volt grade in to the bore well ISI marked, commisioned and tested complete all as specified and directed .The cost shall be included dismantling cable from 50 mtr depth of borewell and again fixing new cable in existing submersible pump with water proof joint and again lowering of pipe with submersible pump with motor and power cable, without disturbinbg of casing pvc pipe

Taking out U/s & Supply and fix GI tubing light grade 40 mm dia with all fitting inside the fountain including suitable support made of GI pipe medium grade,Flange nut bolt , bend, wherever required . Note The Cost of fixing of nozzle given in schedule in pipe and make holes for fixing of nozles and welding of pipe make circular, Hose nipple 40 mm dia , nozzle on pipe and bending of pipe is deemed to be included in the unit rate of item

All as per Item No 98 but 20 mm dia bore complete all as specified and directed by Engineer in Charge.

Taking out unservicable iron made nozzle and Supply and fix brass nozzle of size 1/4 " dia suitable for fountain. the cost shall be deemed to fixing of nozzle with suitable size of socket nozzole welded in existing pipe in foutain complete all as specified and directed by Engineer in Charge.

Taking out unservicable brass nozzle and Supply and fix brass nozzle of size 20 mm dia " dia suitable for fountain complete all as specified and directed by Engineer in Charge.

Taking out unserviceable and S&F under water LED lights lumiplus V1 PAR56 16/20Watt and niche. Make : Astral, Haywards, Leisure Pool. (multicolour) water proof luminaries with of high out put of LEDs housed in complete enclosure of stainless steel body toughened glass with elastomer seal special plastic cable gland compact socket head fastners and mounting bracket are all of stainless steel provided for aiming the object all as specified and directed.

Taking out U/s & Supply and fix LED light 15 /20 watts and RGB (multicolour with remote ) water proof luminaries ip 65 protection with of high out put of LEDs housed in complete enclosure of stainless steel body toughened glass with elastomer seal special plastic cable gland compact socket head fastners and mounting bracket are all of stainless steel provided for aiming the object all as specified and directed.

Taking out unservicable aluminium, cable of size 2.5 and Supply and fix 3 core 2.5 sqmm cable PVC insulated and sheathed sumersible type with stranded copper conductor complete all as specified and directed by Engineer in Charge.

Taking out unservicable aluminium cable of size 1.5 sqmm and Supply flexible cable 1.5 sqmm 3core PVC insulated and sheathed submersible type with stranded copper conductor complete all as specified and directed by Engineer in Charge.

Taking out unservicable starter and Supply and fix three phase Motor starter with suitable arrangement for floor mounted three phase DOL starter ubical type, for indoor door type use, floor mounted, factory fobricated, dust, weather & vermin proof, powder coated, made out of CRCA sheet of 2.15 mm thick and angle iron legs of size 50 mm x 50mm x 5mm with front openable with locking arrangementswith , incoporating Heavy duty 4 pole contactor type TC1-DX overload relay type LR3D,Auto start switch , 3 position slector switch for Single phase preventer , auto/SPP manual/Manual (AS4), on/OFF rocker switch, RYB LED indicator, Motor ON&trip LED indicator , DOL in sheet steel enclosure suitable for capacity submersible pump with relay range 9-14 Amps - AT No BE1SPSDDX204316X-B Make C&S / MU-G6(SS97756) L&T.

Taking out unservicable starter and Supply and fix single phase Motor starter with suitable arrangement for floor mounted single phase DOL starter with suitable arrangenment of ubical type, for indoor type use, floor mounted, factory fobricated, dust, weather & vermin proof, powder coated, made out of CRCA sheet of 2.15 mm thick and angle iron legs of size 50 mm x 50mm x 5mm with front openable with locking arrangementswith and fix single phase Motor starter DOL in sheet steel enclosure suitable for capacacity submersible pump with relay range 23-32 Amps -CAT No BE1SDA4025MU253 Make C&S / SS96560 L&T Note : The cost of PCC foundation shall be deemed to be included in this item rate. (Igloo)

Taking out unservicable MCB and Supply and fix MCB TP 63 amps, 415 volt having breaking capacity 10 KA 'C' curve complete all as directed by Engineer in charge.

Taking out unservicable MCB and Supply and fix MCB SP 5-32 Amps capacity having breaking capacity 10 KA 'C' curve complete all as directed by Engineer in charge.

M&L for cleaning of fountain of size 4 mtr dia and depth of 0.5 mtrby pumping out the water below foot valve and cleaning entire internal surface by removing dirt, sludge etc with wire brush by applying bleaching powder and fresh water and clean entire surface repeatedly with fresh water and pumping out soiled water complete including writting the capacity and date of cleaning with white paint over black painted surface in all respect and as specified and directed (Peroidity ad directed by Engr-in-Charge

All as above but for cleaning of fountain of size 2.5 mtr dia and depth of 0.5 mtr

All as above but for cleaning of fountain of size of stepped type 10 mtr X 15mtr X 10mtr mtr

All as above but for cleaning of fountain of stepped type 5 mtr X 10mtr X 10mtr mtr

Dismantling monoblock pump set 01 HP to 5 HP 3 phase 415 V from foundation base plate after isolating the electric and earth lead connections, suction and delivery pipes etc opening the pump set, motor rotar and statar etc for repair/overhauling and varnishing and baking the stater winding to enhance the insulation level and reassemblying the pumpset and reinstalling on foundation frame connecting, testing and commissioning complete all as directed by Engineer in Charge. Note :- All spares shall be measured as supply only under seperate items

(a) Pump shaft sleeve made out of gun metal

(b) Key for main shaft/impeller

(c) Check nut

(d) Water seal

(e) Ball bearing complete existing size ISI marked

Dismantling submersible pump set type up to 10 HP 3 phase 415 V from existing location after isolating the electric and earth lead connections, suction and delivery pipes etc opening the pump set, motor rotar and statar etc for repair/overhauling and varnishing and baking the statar winding to enhance the insulation level and reassemblying the pumpset and reinstalling on foundation frame connecting, testing and commissioning complete all as specified. Note :- All spares shall be measured as supply only under seperate items

a) Cast iron impeller

b) Bearing suitable for existing submersible pump

c) bush

d) Water seal

(e)Key for main shaft/impeller

Dismantling submersible pump set type up to 5 HP 3 phase 415 V from existing location after isolating the electric and earth lead connections, suction and delivery pipes etc opening the pump set, motor rotar and statar etc for repair/overhauling and varnishing and baking the statar winding to enhance the insulation level and reassemblying the pumpset and reinstalling on foundation frame connecting, testing and commissioning complete all as specified.

a) Cast iron impeller

b) Bearing suitable for existing submersible pump

c) bush

d) Water seal

M & L for Rewinding of pump motor 415 Volt 3 phase after disconnecting electric cable and eath lead, suction and delivery pipes, shifting to work shop, dismantling the motor assembly and removing the burnt out copper winding of stator rotor and cleaning the stator slotsand rotor and core assembly, rewinding to stator and rotor suitable gauge super enamelled copper wire with insulating papers and insulation cloths, varnishing the winding and baking heating for achieving the required insulation resistance, re-assembling the motor and testing complete, incl transporting back to site and fixing motor to its original place, reconnecting electric cable and earth leads etc testing and commissioning complete in all respect all as specified and as directed by Engr-in-charge for the up to 7-10 HP capacity

All as above but 10-15 HP

All as above but 40 HP

S&F in repair for wiring with flexible cable 0.5 sqmm 3core PVC insulated and sheathed sumersible type with stranded copper conductor (for Light)

Material and Labour for Disconnecting the existing 150/200/mm DI/CI pipe ,suction and delivery of any type from the pump set and supply and fixing with new NRV and foot valve of size 150/200 mm bore given in schedule and again connecting of the same with leak proof joint of pipe after fixing of NRV/Foot valve all as specified and directed. Note :- The cost shall be included nut bolt, Rubber packing/gasket, Tee, Flange, Mehanical joint, Collar , nipple, union, weldign work or lead joint etc

S& F in replacemnt of 40 mm bores of tubes 'medium grade' galvanised with all fittings and fixed complete laid in trenches.

S& F in replacemnt of 25 mm bores of tubes 'medium grade' galvanised with all fittings and fixed complete laid in trenches/wall and ceilin or laid in floors

S&F in replacement of Insulating Mat 2mx1mx10mm all as specified and directed.

M & L for excavation in trenches, not exc 1.5 m wide and not exc. 1.5 m in depth and getting out hard/dense soil all as specified and as directed.

M & L for returning filling in including spreading, levelling, watering and ramming in layers not exceeding 25 cm thick with earth obtained from excavation all as specified and as directed.

M & L for removal of surplus soil to a distance not exceeding 50 mtrs and depositing where directed at a level not exceeding 1.5 mtr above the starting point all as specified and as directed.

M&L Fazilka sand as in sand cushioning to under ground cable including punning down all as directed by Engr-in-Charge

Supply and laying reinforced precast concrete cable cover, class LV, type 1, flat size 250 mm x150 mm x 40 mm all as specified and as directed

Taking out U/S & Supply and install verticle submersible pump set 3 ph 415 volt 2760 RPM 270 LPM 27-36 meter head suitable for water fountain. Note : The contractor will be deposit the U/S pump in MES store yard after dismantling of pump

Taking out U/S & Supply and install Verticle submersible pump set 3 ph 415 volt , 770 LPM, Head 129 meter head suitable for water fountain. Note : The contractor will be deposit the U/S pump in MES store yard after dismantling of pump

Taking out unservicable starter and Supply and fix single phase Motor starter DOL in sheet steel enclosure with suitable arrangement for floor mounted three phase DOL starter ubical type, for outdoor type use, floor mounted, factory fobricated, dust, weather & vermin proof, powder coated, made out of CRCA sheet of 3.15 mm thick and angle iron legs of size 50 mm x 50mm x 5mm with front openable with locking arrangementswith , suitable for 3/5 HP capacacity submersible pump with relay range 9-15 Amps -CAT No BE1SDA4025MU253 Make C&S / SS96560 L&T

SWARN SINGH AND CO.

R K GOYAL & COMPANY

M/S GOYAL BUILDERS