Construction of 96 TNGRHS

Amount

Earth work open excavation by manual means in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers

Earth work excavation SDR - (Not Requiring Blasting) and depositing on bank with initial lead of 10 m & initial lift of 2m in Soft disintegrated rock, laterite, soft rock or kankar,not requiring blasting.etc.,complete complying with standard specification and as directed by the departmental officers

1.50 m to 2.00 m depth

2 to 3 m depth Hard rock req blasting

Earth work excavating MDR - (Not Requiring Blasting) Upto 1.25 m width and depositing on bank with initial lead of 10 m & initial lift of 2m in Soft disintegrated rock, laterite, soft rock or kankar, not requiring blasting etc.,complete complying with standard specification and as directed by the departmental officers

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15cm thick well rammed with surface vibrator, watered and consolidated etc., complete complying with standard specification and as directed by the departmental officers.

Cement concrete 1:4:8 ( One of cement, four of M Sand and eight of hard broken stone jelly) for foundation using 40 mm size broken stone jelly inclusive of shoring, strutting, baling out water wherever necessary ramming, curing and water charges etc., complete in all respect complying with relevant standard specifications and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with filling crushed stone Sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supply and filling in foundation and basement with Gravel in layers of not more than 15cm.thick well rammed watered and compacted with surface vibrator, watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing and water charges etc. complete complying with standard specification and as directed by the departmental officers.

Fly Ash Brick Work in cement mortor 1:5 ( One of cement and five of M -sand) using best quality Fly ash Brick of size 230x110x70mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. other type of bond shall be done as directed by the Executive Engineer in charge.

Fly Ash Brick Work in following Cement Mortar 1:6 ( One of cement and Six MSand) using best quality Fly ash Brick of size 230x110x70mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. other type of bond shall be done as directed by the Executive Engineer in charge.

Stilt floor

First floor

Second floor

Third floor

Forth floor

Fifth floor

Brick partition walls of 11.50cm thickness using best quality Fly Ash Bricks of size 23 x 11 x 7 cm in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Stilt floor

First floor

Second floor

Third floor

Fourth floor

Providing and laying in position, Standardised Concrete Mix M-30 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m’) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Below Ground Level

Up to 1.50 m to 4.50 m Depth

Up to 0 m to 1.50 m Depth

Above Ground Level

Stilt Floor

First floor

Second floor

Third floor

Forth floor

Fifth floor

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner , vertical stiffener, side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation.

Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam,Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m(expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers.

Supplying and erecting centering for plane surfaces such as RCC Floor Slab, Roof Slab Loft, Landing Slabs, etc with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over steel adjustable span of size 2m x 2m (expandable upto 3.60m) and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers.

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 2.10 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton and as directed by the departmental Officers.

Supplying and erecting steel centering including necessary supports For planesurfaces such as rectangular or square RCC columns etc. which require onlynominal strutting using mild steel sheets made of 10 gauge thick welded with MS anglesize 40mm x 40mm x 5 mm and supported by Steel Adjustable Telescopic Props of Size2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mmthick) and inner steel pipe with dia 40mm (2.90mm thick).etc..complete in all floors complying with standard specifcation. Steel Adjustable telescopic props shall be providedas directed by the departmental Officers.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc. using mild steel sheets of size 1200cm x 60cm and 10 BG stiffened with welded mild steel angles of size 40mm x 40mm x 5 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner, Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals. MS Channel Section (ISMC 100) shall be provided as a vertical [email protected] C/C and with Lateral support of Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) & steel pipes of 20mm dia @ required level/spacing etc. complete complying with standard specifcation and as directed by the departmental officers.

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given including cost of steel reinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.

Below Ground Level

Ground Level

First floor

Second floor

Third floor

Fourth floor

Fifth floor

Supplying and fixing in position of stainless steel hand rails with Balustarder for stair case with top hand railing pipe of 50.80 mm dia with 40mm vertical post at 1000mm interval to a height of 900 mm with horizontal support fabrication pipes of 38.30 mm dia - 5 line, pipe design with 12 mm dia pipe connecting two vertical and bottom horizontal pipes and fixing 100 mm dia ring with 12 mm dia base cup for every vertical post all stain less steel pipes are 1.60 mm thick pipe, 304G to be fixed and fabrication with gas tungsten arc welding, fixing with lock fix paste and cleaning with passivation paste to remove the welding film with fine polishing including drilling the tiles or granite including conveyance, loading unloading etc all complete complying with relevant standard specification and as directed by the departmental officers.(The quality of all the materials should be got approved before use on works)

Supplying and fixing of Best Indian teakwood wrought and put up for frames of doors including thress hold plate for door and for any other similar joinery works with necessary plugs, rebates for shutters plaster grooves on all faces etc., including labour charges for fixing hold fasts complying with relevant, standard specifications etc., complete in all respectsand and as directed by the departmental oficers.

upto 3 m Length

Supply and fixing of UPVC glazed window made out of hollow multi-chambered UPVC sections having isolated drainage and reinforced with galvanized steel. The corners and joints shall be mitre cut and fusion welded. The outer frame of the window shall be made out of UPVC sections having an overall size of 60mmx60mmx40mm having wall thickness of 2.3mm, + or - 0.3mm and provided with steel reinforcement at a hardware location and size of 27mmx21.5mm. The fixed mullion shall be made out of UPVC sections having an overall size of 76mmx60mmx36mm having wall thickness of 2.3mm, + or - 0.3mm. It is also reinforced with steel reinforcement at a hardware location and size of 27.5mmx17mm. The shutter frame shall be made out of UPVC sections having an overall size of 78mmx60mmx38mm having wall thickness of 2.3mm, + or - 0.3mm and provided with steel reinforcement at a hardware location and size of 25mmx34.5mm. The glazing provided shall be of 5mm thick. Suitable snap fit glazing and function beading shall be provided. The single glass beeding shall be made out of unplasticised polyvinyl chloride section having an overall size of 34mmx20mm having wall thickness of 2.3mm, + or - 0.3mm. Weathering strips and seals shall be manufactured out of E.P.D.M.(Ethylene Polimer Dimonomer). Weather gasket and glazing gasket shall be provided in the grooves to hold the glass and panel for the frame and shutter. All hardwares are made out of materials resistant to atmospheric corrosion. Windows are to be provided with variety of security devices like multipoint locking system, friction stay and powder coated Multi point handles as per the requirement all complete in all respects complying with relevant standard specification. The model and Brand of the UPVC window shall be got approved by the CE/SE before fixing.

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug as per the requirement all complete in all respects complying with relevant standard specification. The model and Brand of the UPVC door shall be got approved by the CE/SE before fixing.

Supply and fixing of UPVC glazed ventilator made out of hollow multi-chambered UPVC sections having isolated drainage and reinforced with galvanized steel. The corners and joints shall be mitre cut and fusion welded. The outer frame of the window shall be made out of UPVC sections having an overall size of 60mmx60mmx40mm having wall thickness of 2.3mm, + or - 0.3mm and provided with steel reinforcement at a hardware location and size of 27mmx21.5mm. The fixed mullion shall be made out of UPVC sections having an overall size of 76mmx60mmx36mm having wall thickness of 2.3mm, + or - 0.3mm. It is also reinforced with steel reinforcement at a hardware location and size of 27.5mmx17mm. The shutter frame shall be made out of UPVC sections having an overall size of 78mmx60mmx38mm having wall thickness of 2.3mm, + or - 0.3mm and provided with steel reinforcement at a hardware location and size of 25mmx34.5mm. The glazing provided shall be of 5mm thick. Suitable snap fit glazing and function beading shall be provided. The single glass beeding shall be made out of unplasticised polyvinyl chloride section having an overall size of 34mmx20mm having wall thickness of 2.3mm, + or - 0.3mm. Weathering strips and seals shall be manufactured out of E.P.D.M.(Ethylene Polimer Dimonomer). Weather gasket and glazing gasket shall be provided in the grooves to hold the glass and panel for the frame and shutter. All hardwares are made out of materials resistant to atmospheric corrosion. Windows are to be provided with variety of security devices like multipoint locking system, friction stay and powder coated Multi point handles as per the requirement all complete in all respects complying with relevant standard specification. The model and Brand of the UPVC ventilator shall be got approved by the CE/SE before fixing.

SuSupplying and fixing Teakwood fully panelled (Single Leaf) shutters using Teakwood scantlings of size 90x40mm for styles & rails, 22mm thick planks for panels(5 Nos) and Brass Furniture fittings(3 Nos - Brass Hinges 125x30mm, 2 Nos - Brass Tower bolt 300x12mm, 1 Nos - Brass Tower bolt 200x12mm, 1 Nos - Brass Aldrop 250x16mm, 2 Nos - Brass Handle 200mm) including cost of wind appliances and labour charges for fixing the furniture fittings in position etc., complete complying with standard specification and as directed by the departmental officers

Supply and fixing of brass door magic eye including necessary matrial, tools and labour charges,etc., all complete and as directed by the departmental officers

Supplying and fixing solid core flush door shutter of following type with thickness with necessary T.W. internal lipping alround conforming to IS 2202-1(1999) including cost of wind ppliances and furniture fittings such as 3 Nos SS 304 Grade Butt Hinges of size (125mm x 30mm) , 2 Nos .300x12mm aluminium tower bolt 1 No. 200x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 2 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete complying with standard specification and as directed by the departmental officers - Single leaf.

PVC Panelled Door Shutters Hollow Type - 200mm x 20mm panels with 1mm wall thickness for panels and styles and rails of suitable size with 2mm wall thickness suitably reinforced using MS Angle / Flat including cost of necessary aluminium hinges and other furniture fittingsetc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing of Magnetic door catches of best quality including cost of all materials and labour charges etc all complete in all respects complying with relevant standard specification and as directed by the departmental officers

Supplying and fixing of MS hold fast horizontally twist of size 230 x 40 x 4mm with a pair of suitable Iron screws etc., all complete in all respects complying with relevant standard specification and as directed by the departmental officers

Supplying and fixing Mild Steel grills for windows, ventilators etc.,complete complying with standard specifications and as directed by the departmental officers

Dadooing walls with following best approved quality, white / colour glazed tiles conforming to IS 15622 of following sizes in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best quality Double Charged Vitrified Tiles of size 600 x 600 x 8mm and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in accordance with IS 1443 in Cement Mortar 1:3 (One Cement and Three crushed stone sand), with required Cement Slurry and Mortar Plasticizer, 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with tandard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and fixing of polised jet block granite wall cladding slab of 10mm to 12mm thick of best approved quality laying cm 1:2 including labour charges,water charges etc., complete complying with standard specification and as directed by the departmental officers

Paving the floor with best approved quality fine polished Granite Stone Slabs of following size and Variety with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complete complying with standard speicification and as directed by the departmental officers.(The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before fixing.)

Supplying and fixing of granite slab sink of size 600 x 600 x 250mm including labour charges,water charges etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing fine polished cuddapah slab 20 / 30mm Thick of following thickness for cup board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as directed by the departmental officers

Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two crushed stone sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Providing 150mm/75mm/50 mm wide band with cement mortar 1:5 ( One of cement and five of sand) 12mm thick finished with neat cement including, scaffolding curing,water charges etc., complete complying with relevant standard specification and as directed by the departmental officer .

Providing 150mm thick band

Providing 75mm thick band

Providing 50mm thick band

Finishing the top of terrace floor with one course of solar reflective water proof, heat proof, cool proof tiles of size 300mm x 300mm x 8mm of approved quality laid in cement mortar 1:3 (One part of cement and three part of M Sand) mixed with chemical mineral powder (60 kg for 1000 Sqft) (before laying tiles, the tiles should be dipped with salin based nano liquid) and top pointing with cement mortar 1:3 (One part of cement and three part of M Sand) mixed with white cement, silicon powder and polymer additives (20Kg of 1000 Sqft) and joint pointed with a base concrete of PCC 1:2:4 using 6 to 10 mm metal for providing necessary gradient at top of roof etc., complete complying with standard specifications including cost of all materials, labour charges for lifting to open terrace, laying and finishing and other incidental charges etc., complete and as directed by the departmental officers. (The Brand and quality of tiles should be got approved from the Superintending Engineer/Chief Engineer before using)

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with cement mortar 1:5 ( One of cement and five of P Sand) 12mm thick finished with neat cement including, providing band cornice scaffolding curing etc., complete complying with relevant standard specification and as directed by the departmental officer

Plastering in C.M 1:3 (one of cement and three of P Sand) 12mm thick mixed with water proof compound 2 kg per 10 sqm including scaffolding, curing ,finishing etc all complete in all respects complying with relevant standard specification and as directed by the departmental officers.

Weathering course with broken brick jelly lime concrete using 20mm gauge broken brick jelly in pure slaked lime ( no sand) over roof slab to the proportion of brick jelly to lime ( Fat lime) being 32: 12 1/2 by volume well beaten with wooden beaters, for giving the required slope and thickness complying with relevant standard specification and as directed by the departmental officers.

Finishing top of flooring with CM 1:3 ( one cement and three of granite chips of size 10mm and below) 20 mm thk Ellis pattern flooring and surface rendered smooth including 150mm wide skirting, providing proper slopes, thred lining, curing etc complete in all floors complying with relevant standard specification

Painting the walls with two coats of cement paint over one coat of cement primer as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications and as directed by the departmental officers. (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use of work).

Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications and as directed by the departmental officers. (The wall putty shall be got approved by the Executive Engineer before use of work).

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed by the departmental officers.

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat on cement plastered wall surface ect., complete complying with standard specification and as directed by the departmental officers.

Best Varnishing Woodwork two Coats of approved quality in all floors etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality of paint should be got approved by the Executive Engineer before use on works.)

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

110mm dia PVC Pipe Fifth Floor

Supplying, laying and jointing UPVC pipes of Class 5 (having working pressure of 10 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works - External water supply above ground level / Below ground level.

For laying UPVC pipes of dia 50mm

For laying UPVC pipes of dia 32mm

For laying UPVC pipes of dia 25mm

For laying UPVC pipes of dia 20mm

Supplying, laying and jointing of 20 mm dia CPVC pipes OF Standard Dimension Ratio -13.50 (Pressure class 2) conforming to IS:15778 - 2007 of approved quality and best variety of the following dia including cutting and fixing CPVC specials using CPVC adhesives (Solvent Cement) (but excluding cost of such specials) and fixing into wall with teak wood plugs,CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications and as directed by the departmental officers. (The CPVC pipes shall be got approved by Executive Engineer before use on works) - Internal water supply above ground level.

Supplying and fixing of C.P Concealed stop Cock with sliding flange (Model No. 514 E) of Essco Fittings including cost of fittings , labour for fixing etc, complete complying with relevant standard specifications and as directed by the departmental officers. (The quality of fittings should be got approved from Superintending Engineer/Chief Engineer before use).

Supplying and fixing in position 15mm dia brass SS Elbow Action Tap of size 15mm CP screw down tap / Pillar tap / Swan neck tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position 15mm dia brass SS Heavy Duty Long Body Tap 15mm of size CP screw down tap / Pillar tap / Swan neck tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing of CP two way bip cock with Health facet with rose including cost of jaguar fittings labour for fixing etc, all complete and as directed by the departmental officers., (The quality of fittings should be got approved from Superintending Engineer/Chief Engineer before use).

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work

Fixing Gun Metal Gate Valve of dia 32mm

Fixing Gun Metal Gate Valve of dia 50mm

Supplying and fixing in position CP shower rose with CP stop cock arrangement of size 15mm dia inlet and 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers (The CP shower rose should be got approved by the Executive Engineer before use on works).

Supplying and fixing of C.P mixer 3 in 1 with provision for Over Head Shower with jaguar fittings 15mm long bend pipe and wall flange with bush & button divertor fiting, with areator like Jaquar fitting or equivalent, including cost of fittings, labour for fixing etc,all complete and as directed by the departmental officers., (The quality of fittings should be got approved from Superintending Engineer/Chief Engineer before use).

Supplying and fixing in position best quality and approved make Indian made white /colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia “B” class GI waste pipe with rubber plug and chain, 15mm dia M wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supplyconnection and painting the brackets with two coat of painting over a priming coat anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with crushed stone sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position White / Colour Special Delux Model Glazed Cascade Type Parryware / Hindware / Equivalent Wall Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) with 10 litres capacity flushing tank with all internal dual flush fittings with normal seat cover Wall Fitting

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works).

110mm dia PVC SWR pipe including all required PVC specials etc., all complete.,

75mm dia PVC SWR pipe including all required PVC specials etc., all complete.,

Supply and fixing of CI Nahani Trap 75mm (Superior Variety) with SS gratings having minimum of water seal of 50mm confirm to relevant I.S. specifications with its latest amedments including resting on the bed of brick jelly concrete 1:5:10 (One of cement, five of M Sand and ten of 40 mm gauge brick jelly) etc., complete complying with relevant standard specification and as directed by the departmental officer. (The CI Nahani Trap should be got approved from the CE/SE before use)

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of Fly ash Bricks of size 9” x 43/8” x 23/4” with Class designation of 7.5 and Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officersas per standard specification.

45 cm x 45 cm x 60 cm

60 cm x 60 cm x 60 cm

90 cm x 90 cm x 90 cm

Supplying and fixing in position 150 x 100mm “P” or “S” stoneware gully trap ‘A’ grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three crushed stone sandand Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works)

Supplying, laying and joining the following dia Pressure polyvinyl chloride (pvc- u) pipes For use in underground drainage and sewerage systems as per IS socket ends in dry conditions and tested with water including necessary earth work exacavation for trenches and refilling the same well rammed and consolidated after the pipes are joined with PVC solution and tarred yarn laid to proper gradient to the alignment etc., complete complying with relevant standard specification and as directed by the departmental officer. ( SW pipes should be got approved by the Superintending Engineer/Chief Engineer before laying)

160mm dia Pvc pipe

Supplying & Fixing of SFRC cover slab 600X600mm including the cost of labour, water charges etc, complete in all respects and as directed by the the departmental officers.

Supplying & Fixing of C.I. steps including the cost of labour etc, complete in all respects and as directed by the departmental officers

Wiring with 1.5 sqmm copper PVC insulated unsheathed single core 1.1 K.v. grade cable with continuous earth by means of 1.5 sqmm copper insulated unsheathed single core 1.1 k.v. grade cable in fully concealed PVC rigid conduit pipe heavy duty with ISI with suitable size MS box of 16 g thick concealed and covered with 3mm thick laminated hylem sheet controlled by 6 amps modular switch including circuit mains cost of all materials, specials etc., all complete.

Light point with ceiling Rose

Light point with Backlite Battern Holder

Wiring for calling bell / Buzzer

Wiring with 1.5 sqmm copper P.V.C. insulated unsheathed single core 1.1.k.v. grade cable with continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core 1.1.k.v. grade cable in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS box of 16g thick concealed for Fan point controlled by 6 amps Modular type switch including circuit mains, cost of all materials, specials, etc., all complete for Fan point

Wiring with 1.5 sqmm copper P.V.C. insulated unsheathed single core 1.1.k.v. grade cable with continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core 1.1.k.v. grade cable in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS Box of 16g thick concealed for Staircase light point controlled by 6 amps Modular type two way switch including circuit mains, cost of all materials, specials, etc., all complete

Wiring with 1.5 sqmm copper P.V.C. insulated unsheathed single core 1.1.k.v. grade cable with continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core 1.1.k.v. grade cable in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS box of 16g thick concealed for 6 amps 5 pin plug socket point at Switch Board Itself Modular type including circuit mains, cost of all materials, specials, etc., all complete

Wiring with 1.5 sqmm copper P.V.C. insulated unsheathed single core 1.1.k.v. grade cable with continuous earth by means of 1.5 sq.mm copper PVC insulated unsheathed single core 1.1.k.v. grade cable in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS box of 1 No (each) 16g thick concealed for 6 amps. 5 pin plug socket point at convenient places Modular type including circuit mains, cost of all materials, specials, etc., all complete

Supplying and fixing 15amps 3 pin plug Modular type Switch and socket on a suitable MS box 16g thick concealed inclusive of all connections and cost of all complete in all respects complying with relevant standard specification and as directed by the departmental officer.

Supplying and fixing Stepped Electronic 300W / 450W Square Type Fan regulator on a suitable MS box 16g thick concealed inclusive of all connections and cost of all materials.

Supply and fixing of 48" Ceiling Fan 5 Star Rated (without Regulator) - all complete complying with relevant standard specifications & as directed by the departmental officers.(The Ceiling Fan should be of reputed Brand and it should be got approved by the Competent authority before fixing).

Supplying & fixing of Exhast Fan with regulator including labour charges etc. all complete as directed by the Departmental Officers.

AC Exhaust Fan 300mm (12”) Sweep (Light Duty)

Supplying, fixing, connecting and commissioning of 32 AMPS Metal clad socket (Superior variety) combined with 20AMPS SP MCB in Manufactures mount box fixed flush with the wall including cost of material, necessary interconnection etc, on suitable angle Iron frame work with earthing etc., all complete in all respects complying with relevant standard specification and as directed by the departmental officer.

Supplying & fixing of water tight bulk head fittings with chokeguard and 12 watts LED light including necessary connections cost of materials, supply of one number of Bulk Head fitting, 12 watts LED lamp etc. all complete as directed by the Departmental Officers.

Supplying and fixing concealing of MS modular box of size 8" x 6" x 4.5" concealed with 3mm thick hylem sheet for TV/Telephone Junction connection including necessary materials etc all complete in all respects complying with relevant standard specification and as directed by the departmental officer.

Supplying laying and concealing of 25 mm dia PVC pipes with necessary specials and other materials including run off 1no.fishwire (GI 22 G) for drawing cable for TV and telephone etc., all complete in all respects complying with relevant standard specification and as directed by the departmental officer.

Supply and fixing of 7 segment Three Tier Three Phase Vertical Distribution Board with 8 way per Phase, 63 Amps 4 Pole MCB - 1No., 40 Amps FP ELCB - 3No ., 6/16Amps SP MCB - 24 No etc., and as directed by the departmental officer

Supplying and fixing three phase MS HORIZONTAL THREE PHASE DISTRIBUTION BOARD WITH MCBS 6 way TPMCB sheet steel distribution boards flush type / surface type fitted with bus bars and neutral links with single / three phase MCB outgoings and separate 4 way provision for accommodating One No. 4 pole incoming MCB/Isolator and another separate 4 way provision for accommodating One No. 4 pole 63 A ELCB / RCD with label holder, 18 Nos. of 6-16A MCB and provisions for taking up cable for size not less than 35 sq.mm. all complete in all respects complying with relevant standard specification and as directed by the departmental officer.

Run of main with 2 wires of 2.5 Sqmm Copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 and with continuous earth by means of 2.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed 19/20mm dia rigid PVC conduit pipe with ISI mark etc. including cost of all materials, specials etc. all complete in all respects complying with relevant standard specification and as directed by the departmental officer.

Run of main with 2 wires of 4 Sqmm Copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 and with continuous earth by means of 2.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed 32/25/20mm dia rigid PVC conduit pipe with ISI mark etc. including cost of all materials, specials etc. all complete in all respects complying with relevant standard specification and as directed by the departmental officer.

Run of main with 4 wires of 6 Sqmm Copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 and with continuous earth by means of 2.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed 32/25/20mm dia conduit pipe with ISI mark etc. including cost of all materials, specials etc. all complete in all respects complying with relevant standard specification and as directed by the departmental officer.

Supplying and laying of 8 SWG , G. I wire on walls/below G.L. with necessary "U" nails earth work excavation and refilling etc., including cost of all materials etc. all complete in all respects complying with relevant standard specification and as directed by the departmental officer.

Supplying and laying of 8 SWG , copper wire on walls/below G.L. with necessary "U" nails earth work excavation and refilling etc., including cost of all materials etc. all complete in all respects complying with relevant standard specification and as directed by the departmental officer

Earthing arrangements with GI Earth Plate including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work, re-filling the sides of foundation with excavated earth as per the standard specification and as directed by the Departmental Officers.

Supply and fixing of 25mm x 3mm Copper earth flat with necesarry clamps including cost of all materials and labour etc. all complete in all respects complying with relevant standard specification and as directed by the departmental officer.

Supplying and laying of L.T. Cables 3.5 Core 1.1 KV Grade Armoured Aluminium Conductor cable confirming to IS 1554 part I with ISI mark 25 Sqmm cable , cost of cable tray all material Labour charges etc., complete in all respect and as directed by the departmental officers

Supply of 63A Connector Box:Size 250x250x250mm One set of 63A TPN Terminal Box etc.. all complete complying with relevant standard specifications & as directed by the departmental officers.

Supplying laying and connecting 31/2 C x 150 sq.mm aluminum armoured UG cable with ISI mark of reputed brand including fixing in walls with necessary MS clamps, brass screws including cost of all materials redoing the dismantled portion, etc., all complete complying with relevant standard specification and as directed by the Departmental Officers. (The quality and brand of UG cable should be got approved by SE/CE before use).

Supplying laying and connecting 31/2 C x 240 sq.mm aluminum armoured UG cable with ISI mark of reputed brand including fixing in walls with necessary MS clamps, brass screws including cost of all materials redoing the dismantled portion, etc., all complete complying with relevant standard specification and as directed by the Departmental Officers. (The quality and brand of UG cable should be got approved by SE/CE before use).

Supplying and fixing of 18w 4 feet LED light fittings etc.,complete with ISI mark, complying with relevant standard specifications & as directed by the departmental officers. ( The Brand/Quality of fittings and Lamp has to be got approved by the CE/SE before fixing)

Supply anf fixing of best approved superior quality concealed fiber box with MS Fan Hook of 100 mm dia 75 mm depth 3mm thick including cost of fixing in possition etc all complete as directed by the Departmental Officers. ( The Brand/Model of the fan Hook has to be got approved by the SE/CE before fixing)

Supplying and fixing of DECORATIVE TWIN FLUORESCENT TYPE FITTING WITH COPPER CHOKE & CONDENSOR COMPLETE SUITABLE FOR 2 Nos. FLUORESCENT TUBES complete with suitable length of 32 mm dia GI pipe class B on the existing gate piller with supply and fixing of MS box of 30cmx20cmx10cm with angle iron frame work with door and lock key arrangement with supply and fixing 16 amps fare unit 250V 6 amps SP switch in side the MS box with PVC unsheathed copper lead with 24 watts retrofit LED lamp.

Providing expansion joint pad of Bitumen Felt 15 mm thick Pad for road work interval including cost of materials and labour charges and as directed by the departmental officers

Design manufacture,supply,delivery,erection, testing and commissioning of 15 passenger Stretcher-cum-Passenger Lift MRL Stretcher-cum-Passenger Lift MRL, Speed 1 m/s with Stainless Steel Panels, Disable friendly, microprocessor based controller, VVVF drive, Fire rated doors and ARD

Supplying and Planting avenue trees of approved varities of grown up trees 2m height including earth work excavation 60cm x60cm x60cm filling with red earth mixed with manure to 30cm depth in two layer M sandmaintaining for the period of six month including cost of plants, cost of supporting posts, conveyance and labour charge for planting, weathering and maintaining etc.. complete in all respect as directed by departmental officers.

Providing tree guards with chicken mesh using casurina posts of 8 to 10cm dia, 4 nos vertical and bottom fixed in C.C 1:8:16 using 40mm guage HBS Jelly and top connected with C.W reepers of size 2"x1" and the over all size of guard from G.L 75x75x120cm height including the cost and fixing of casurina posts C.W.reepers, chicken mesh and labour for tying chicken mesh with C.W repers and nailing the casurina posts and C.W reepers necessary nails, binding wire etc.. complete in all respects as directed by the departmental officers.

Supply and run of 25mm x 6mm GI Flat Down Condutor with necessary clamps / supports on wall / floor / ground for earth connection etc., complete in all respects as directed by the departmental officers.

Supply of Test Link Box for each Down conductor in order to disconnect the earth termination system to enable measurement of resistance complete in all respects as directed by the departmental officers.

Supply and insallation maintenance free GI Earthing System comprising of 50mm dia and 2 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp

Supply and insallation Cabinet Type Class 1 and 2 Combined Model SPD to arrest surges and overvoltages in the power line due to lighning switching action etc. they must be installed in the incoming MCC panel / DB of the respective buling in parallel to the power circuit. Model: PSV4-12.5/400TT (3 phase power network)

Labour Charges for erection and Commissioning of centrifugal motor pumpset the borewell etc all complete complying with relevant standard specification and as directed the departmental officers

Supplying of submercible pumpset 5 HP all complete complying with relevant standard specification and as directed the departmental officers

Supply delivery and fixing of 3 core 4 sqm copper cable flat type with ISI mark suitable for submercible pumpset including labour charges for connecting with panel board and motor etc., complete as directed by the departmental officers.

Plain cement concrete 1:2:4 (One part of cement two of sand and four of HBS jelly) for foundation and other similar works using 20m gauge hard broken stone jelly excluding shuttering and centering but including laying, curing and finishing with relevant standard specifications in foundation and basement, and other similar works & as directed by the departmental officers.

Providing, laying, spreading and compacting graded stone aggregates for Wet Mix Macadam 250mm thick, including premixing the materials with water at OMC in mechnanical mix plant, conveyance of mixed materials by tipper to site, laying in uniform layers using pavers in Sub Base/ Base course on well prepared surface and compacting with vibratory soil compactor to acheive the desired density including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per clause 406 of MORTH Rev-5

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of 75mm thickness in RCC 1:2:4 (one cement, two crushed stone sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and providing HDPE Dust Bin ( 1000 ltrs capacity) with wheel borrow, complete in all respect complying with relevant standard specifications and as directed by the departmental officers.

Supply of 125KVA, ( 6SL1500TA G3) KOEL GREEN GENSET incorporating Kirloskar Water Cooled Diesel Engine, Kirloskar Green alternator, 3 phase, 415 Volts, 0.8 PF, with AUTO MAIN FAILURE (AMF) PANEL, approved Acoustic Enclosure, Battery & Diesel Tank (Generator Used for Producing electricity)Techincal specification enclosed including Liasioning with electrical inspector for preparation of drawing such as schmatic layout , earthing layout etc., submission of drawing to electrical inspector and getting drawing approval. Preparation of work completion report and arranging EI inspection . Preparation of defect report after inspection and obtaining safety certificate. etc complete complying with standard specification and as directed by the departmental officers.

Exhaust support 100x40 MS channel and 10mm plate etc complete complying with standard specification and as directed by the departmental officers.

Hanger Fastner Bolt & Nut etc., complete complying with standard specification and as directed by the departmental officers.

Exhaust pipe insulation 50mm thick SWG 24KG Aluminium seat silencer with mineral wool chickenness etc., complete complying with standard specification and as directed by the departmental officers

Exhaust pipe with silencer etc complete complying with standard specification and as directed by the departmental officers.

Providing Rain water Harvesting pit by earth work of 90cm dia and 60 cm depth and filling with stone jelly 40mm size including earth work excavation filling work with the stone jelly and covering with precast RCC 1:2:4 slabs, precast well ring RCC 1:2:4 including cost of steel and fabrication of reinforcement and grills precasting moulding, curing finishing and placed in position and augaring 300mm dia bore pit to a depth of 4.40m and filling the entire depth of bore pit using river M sand15% 20mm H.B Stone jelly 50% and 40mm H.B Stone jelly 35% including Supplying & fixing 1No. Gully trap with 110 mm dia PVC pipe for jointing including the cost of materials and labour charges etc.. complete in all respect as directed by departmental officers.

Supply and Fixing of Signage /Numbering Plate with 304 grade 18 SWG thickness stainless steel etching name board of size 4" x 2" for Flat directed by the deparmental officers.Number plate is available In black and ash Color and Rectangular/square shape also available which can be mounted in wall with Polished Surface Finish etc complete complying with standard specification and as directed by the departmental officers

Supply and Fixing of Signage /Numbering Plate with 304 grade 18 SWG thickness stainless steel etching name board of size 12" x 12" for Floors directed by the deparmental officers .Number plate is available In black and ash Color and Rectangular/square shape also available which can be mounted in wall with Polished Surface Finish etc complete complying with standard specification and as directed by the departmental officers

Supply and Fixing of Signage /Numbering Plate with 304 grade 18 SWG thickness stainless steel etching name board of size 6" x 6" for Parking directed by the deparmental officers.Number plate is available In black and ash Color and Rectangular/square shape also available which can be mounted in wall with Polished Surface Finish etc complete complying with standard specification and as directed by the departmental officers

Supply and marking of CAR PARKING LINE with chlorinted rubber paint ideal for car parking, formulted to tolerate slightly damp substrate for ventillated internal or external floors including reflective glss beds for enhanced visibility directed by the deparmental officers etc complete complying with standard specification

Supplying and Fixing of English Stainless Steel Letters Letters of approved size and colour. The colour treatment process is achieved with MRF colour coat and then the processed coloured layer is set into the kiln for the heat treatment process for the following sizes directed by the deparmental officers etc complete complying with standard specification

Tamil Letter 60cm (24”)

English Letter 60cm (24”)

Emblem (15”)

Plastering the bottom of flooring in cm 1:4 (One of cement and four of sand) 20mm thick including surface rendered smooth including providing proper slopes, thread lining, curing and 150mm wide skirting alround with the same cement mortar etc., complete in all respects.

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc., complete complying with standard specification and as directed by the departmental officers. .

Providing Dispersion trench of 1.5 m width and 7.5 m depth to the required length filling the trench with 40 mm HBS stone jelly to a depth of 50 cm, laying 230 dia SW pipes in loose joints and refilling trenches with excavated earth to the required depth complete in all respects and as diretced by departmental officers.

Subtotal

Sri Balaji Constructions (BID ID -1447971)