COMPREHENSIVE B/R MAINTENANCE TO CERTAIN OTM AND MD ACCN OF 337 MED REGT AND 42 ARTY DIV CAMP UNDER AGE B/R- II AT ITARANA CANTT ALWAR

Amount

Demolition of brick work built in cement mortar or cement lime mortar including all quion arches etc complete all as specified and directed.

Taking down cement plaster on any type of surface finshes, racking out joints hacking for key scrubbing down with water in any description in any position etc complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters frome the frames) n exc 1.5 sqm each etc complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutte from the frame) exc 1.5 Sqm and not exc 4 Sqm each etc complete all as specified and directed.

Taking down of shutter exc 1 sqm and n exc 2 sqm each and refixing in same opening after easing, adjusting etc complete all as specified and directed.

Demolition cement concrete(unreinfored) as in ground floor and paving not exceeding 15cm thick below or above the ground level.

Dismantling AC/CGI/Fibre sheet (Corrugated,Semi corrugated etc) as in roof etc complete all as specified and directed.

Dismantling wall and any type of ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness fixed to any type of frame including cover fillets etc complete all as specified and directed. Note : Any damage occured on electrical fitting/fixtures during execution of work be repair/rectified and making good disturbed portion by the contractor on his own arrangement.

Dismantling of concrete post as in Roof truss/puline etc any section in any description and making good in disturbed portion etc complete all as specified and directed.

Dismantling floor hearth wall tiling (but not backing) removing servicable tiles to store rubbish off the premisses complete all as specified and directed. Note : Any damage occured on electrical fitting/fixtures during execution of work be repair/rectified and making good disturbed portion by the contractor on his own arrangement.

M&L brick work with fly ash 'brick straight or curved on plan exc 6m mean radius built cement mortar (1:6) etc complete all as specified and directed.

All as per ser item No 11.00 above but except bricks etc complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:6) on fair faces of brick work surface finished even and smooth with out using extra cement etc complete all as specified and directed.

M&L for 15mm thick rendering cement mortar (1:6) on other than fair faces of brick or concrete surface of wall finished even and smooth with out using using extra cement etc complete all as specified and directed.

M&L for Rough cast plaster on exterior walls applying the under coat of cement and sand mortar (1:3) not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm ) mixed with coarse sand and cement in the raio of (1:1:1) shall be applied and finished even. The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered etc complete all as specified and directed by Engineer in Charge

Taking down and removal of loose / disintegrated old concrete up to 50 mm depth/ plaster and cleaning all loose dust washing with water including M&L for applying bonding coat nito bond AR or equivlent of modified styrene butadiene emulsion (SBR Bonding agent by volume with the brushes etc to bind New Cement plaster/ polymer Modified plaster/ concrete/ screed concrete with old surface etc complete all as specified and directed.

M&L for applying 15mm thick plaster with polymer modified mortar fortified with SBR (Nitobond SBR 45 ) in proportion (1:3) by weight 5 litres Nit bond SBR 45 to added to 50 KG Cement with 13 litre water addition, finished surface to match with existing adjoining surface of ceiling, beams and alike etc complete all as specified and directed.

M&L and applying two or more coats of 2 component zinc based epoxy rust preventer (Nitozinc Primer-M) on corroded reinforcement after cleaning and removing the rust from corroded reinforcement with the help of wire brush and treating it with rust remover (Reebaklens RR) including thoroughly cleaning washing air blowing brushing etc complete all as specified and directed. Note : Qty of Zinc based epoxy rust prevent or only shall be taken into account for payment purpose on the basis of actual consumption.

M&L rendering in patches in repairs (n.exc 3 Sqm each patch) 10mm thick in cement mortar (1:4) on fair faces of Brick/stone/concrete surfaces finshing the surface even and smooth without using extra cement etc complete all as specified and directed.

M&L preparation of newly plasterd surface of wall and applying two coats cement base paint over a coat of primer etc complete all as specified and directed.

M&L preparation of newly plasterd surface of wall and applying two coats oil bound distemper over a coat of alkali resistant primer etc complete all as specified and directed.

M&L for preparation of old decorated surface of walls etc and applying one coat of oil bound distemper of approved shade/tint etc complete all as specified and directed by Engr- in - Charge.

M&L machine cut kota stone flooring 20 to 25 mm thick over 20mm thick cement sreed bed CM (1:4), laid and jointed in grey cement slurry mixed with pigment to match the shed of the slab including rubbing polishing etc complete all as specified and directed.

All as per ser item No 23.00 above but as in skirting ,riser of steps,dado and pillar over rendering 10mm thick cement mortar (1:4) etc complete all as specified and directed.

M&L grinding, rubbing polishing of existng kota stone/terrazo flooring etc complete all as specified and directed.

M&L 75 mm thick PCC (1:4:8) type D2 (using 40mm graded aggregate) as in foundation filling and mass concrete as floor sub base etc complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand etc complete all as specified and directed.

M&L chequered cement concrete (coloured) tiles 30cmx30cm x25mm thick set and jointred in net cement slurry in floor and pointed with white cement and piment including 20mm thick screed bed cement mortar (1:4) etc complete all as specified and directed

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

M&L Non skid ceramic tiles 7 to 8mm thick exc 0.18 sqm but n exc 0.36 sqm as in floor set and jointed in neat cement slurry and pointed in colour cement to match the shed of colour over and incuding 15mm thick screed bed cement morter (1:)6 etc complete all as specified and directed.

All as per ser item No 32.00 above but in skirting and dado including 10mm thick rendering cement mortar (1:4) etc complete all as specified and directed.

M&L for non skid ceramic tiles (coloured) 7 to 8 mm thick any colour of area of each tiles exc 0.06 Sqm but n exc 11 sqm each set and jointed in neat cement slurry and pointed with white or coloured lcement to match the shed of tiles laid over and including 15 mm thick screed bed cement mortar (1:6) etc complete all as specified and directed.

M&L for Glazed ceramic tiles any colour in vertical surface 300x450x7 / 450x350x7mm thick over 10 mm thick rendering in CM (1:4) and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles etc complete all as specified and directed.

Excavating in post holes (or similar holes) each n.exc 0.5 cum, getting out in loose/soft soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance n exc 50 m and making good surface

S&F for structural steel as in Trusses , pulines,rafter made of Hallow /square/rectangle/round section including vertical member and necessary tee, angle, cleats including necessary cutting welding notching confirming Fe 290 Gde E165 etc complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enameled paint over a coat of red oxide zinc chrome etc complete all as specified and directed.

M&L PCC (1:4:8) type D-2, using 40 mm graded stone aggregate in foundation filling and mass concrete etc complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and directed.

S&F plain galavanized mild steel plain sheeting 0.63mm thick in ridges, hips, valley gutters, drip and straight flashings ( length and girth as fixed) with grade of zinc coating 275 etc complete all as specified and directed. .

M&L for suspended false ceiling system using 4 mm thick 'E' Board ceiling tiles classic/ designer as approved by GE of size 595 x 595mm (as approved by GE) fixed with and including galvanized iron powder coated GI Grid system suspended from ceiling with provision of galvanized wire 4 mm dia with butterfly clips and wall taping screw i, hold down clips for fixing the board to frame complete all as per manufacturer’s instructions, etc complete all as specified and directed. (a) Size of grid - 600mm x 600 mm. (b) Size of main Tee – 39mm x 24mm (c) Size of cross Tee – 29mmX34mm (d) Size of wall angle – 22.20mm x 22.20mm

S&F in repair false ceiling 'E' board of size 595mmx595mm 4mm thick etc complete all as specified and directed.

M&L wall panelling made of 5 mm thick prelaminated PVC hollow section with tonge and groove joints fixed on wall with necessary screw and adhesive etc complete all as specified and directed by engr in charge . PVC U channel will be provided on top and bottom and PVC angle will be provided in all corners consisting of 5mm thick wood grain printed PVC sheet inclusive of solvant cement and fixing at site on PVC frame as per specification and drawings.

Taking down carefully existing bitumen tarfelt, including plaster of any description over the surfaces of roof, terraces including flashings and junctions of parapets/Curb walls etc and removing of the rubbish to a distance exc. 500m but n.exc. 1.00 Km and depositing where etc complete all as specified and directed bu Enginner-in- Charge.

M&L for Screed bed 20 mm thick in cement mortar (1:4) mixed with Water Proofing Admixture as per manufacture instructions on concrete surfaces of roof slab finishing the surfaces even and smooth etc complete all as specified and directed. Note :- Water Proofing admixture shall be measured and paid seperately.

M&L for cleaning of all loose dirt and dust from roof and priming the surface with one coat of cold applied bituminous primer @ 0.40 Kg/Sqm conforming to IS : 3384 and applying a layer of APP based polymeric membrane not less than 3mm thick weighing not less than 3.50 Kg/Sqm, reinforced with polyester non woven fabric (weighing not less than 150 gms/Sqm) and upper side of membrane thermally insulated with white gravel finish uniformly embedded during manufacturing process laid over a coat of Bitumen primer 85/25. It shall be laid by torch application having side over lap 75 mm and at the end 100 mm, all overlaps and joints shall be sealed by torch application. For parapet, membrane shall be taken to a height of minimum 60 cm and inserted inside the parapet in a groove to a depth of 65 mm. The same shall be finished by a membrane flashing. Note : The net area of water proofing treatment shall be measured without any extra allowance for laps & portion inserted in groove which shall be deemed included in the quoted rates.

M&L two coat of reflective silver Aluminium paint over APP membrane etc complete all as specified and directed.

M&L for mild steel framed work as in door frames and gauge shutters made of angle or hallow/square/rectangular/circular section and other covering door to be prepared for handing or sliding with including either hooks , praporsonaly made sliding door bolt , hinges or handles fittings (exclusIve of steel or othr covering, running rails and guides) and hanging also fastening and fixing , necessary arrangements for fixing of wiremesh, necessary bolting including welding complete conforming to FE-290 Gde E-165. Note: Wire gauge will be measured and paid separately

S&F Mild steel black sheet 1.25mm thick fixed with Mild steel frame work for door/gates etc and necessary fixing with screwes/rivets/welding etc complete all as specified and directed.

S& Ffactory made solid Wooden HDF Moulded door shutter 30mm thick (Stiles) with 2,4 or 6 raised panel design with 3mm thick Moulded Door facing sheet on front face & 3 mm thick plain colour Door Facing sheet on back face,, with raised High Density Boiling Waterproof Fiberboard skins, the core shall be consist of solid core using Machine filled Rigid Expanded Polyurethane Foam of minimum density 40kg/cum with including additional wooden blocks for fixing of locks and fixing in frame at site etc The door shall comply with and as per IS 15380 : 2003 & IS 13205 : 1991 etc complete all as specified and directed.

S&F 35 Factory made plain framed panel shutter of 2nd class hard wood with two panel with commercial ply wood face veeners or decorative face veeners , seasoned and chemically treated etc complete all as specified and directed.

S&F factory made 30mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides etc complete all as specified and directed.

M&L for factory made 2nd class hard wood glazed and skelton door shutter made out of stiles & rails of 30mm thick 2nd class hard wood, klin seasoned and chemically pressure treated & open reabted and prepared to receive glass/gauge etc (without sash bars), edges of framing plain,chamfered of rounded, fitted with and mitred beads for securing glass etc compelte, the size of members of shutter shall be as per IS-1003. The shutter shall be fitted to the chowkhats as directed by Engr-in-Charge.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enameled paint over a coat of pink primer etc complete all as specified and directed.

S&F steel window 1.25mm thick box type ERW hollow P section of size 60mm x25mm single rebated comprise of gauged skelton shutter ERW size 50mmx20mm and 1.25 mm thick with two openable leaf consisting two Nos sash bars of T- section 20mmx3mm welded to frame with one vertical mullion of ERW box type T- section of size 60mmx25mm and 1.25 mm thick including cutting holes and making good dismantled portion with PCC (1:2:4) type B-1 (four Nos for each window)including following fittings weled to frame shutter:- (a) Hold fast 150mm long of 12mm x3mm made to shape -04 Nos per window. (b)Handle of z section 20mmx25mm, 100mm long - 01 Nos per leaf. (c) MS Tower bolt 150mm long -02Nos per leaf. (d) Z-section 20mmx25mm 100mm long 01 Nos per leaf. (e) MS pintol hinges of size 75mmx12mm-02 Nos per leaf. Note :(i) Fabrication & fixing shall be as per TD Drawing (ii) Wire mess and painting shall be measured and paid separatly under respective items.

All as per item No 54.00 and above but window with glazed shutter etc complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples to wooden/steel frames with beading etc complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each pane etc complete all as specified and directed.

S&F frame work such as grills,gratring etc,with ends of bars shouldered &/or riveted or forged into spikes,framed guard bars, barred iron door ladder,frame balusters,walk ways, railing,frame work or water tanks & similar work conforming to Fe-290 Gde E-165.

S&F powder coated aluminium door anodised of approved colour( size of frame : 63.5mx38.10mmx2mm thick & size of shutter : door vertical (style ) with gasket of size 46.3mmx45.00mmx 1.50mm thick, top rail of size 47.00mmx45.00mmx1.30mm lock rail/middle rail 83.00mmx44.50mmx1.65mm thick bottom rail 114.3mmx45.00mmx1.50mm thick including S&F of 4.8 mm thick sheet glass with glazing clip, pvc track gasket ,EPDM rubber gasket on glass of weather tightening alongwith recessed type handle, hingees, mortic lock, door closer etc complete all as specified as per TD -2004/61R sheet No 1/1

S&F powder coated aluminium window having three track section 92mmx31.75mm shutter section 40mmx18mm mounted on bearing to slide on track plain anodised of approved colour including S&F of 5 mm thick frosted/plain glass and wire mesh with glazing clip, pvc track gasket ,EPDM rubber gasket on glass of weather tightening alongwith recessed type handle and lock including sealing gap with marble /granite surface with silicon sealent aking it water proof in all manner including aluminium grill etc complete all as specified and directed by Engineer in Charge .

S&F in repair Door closer hydraucally regulated Aluminium (extruded section body) designation No 3 universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed etc complete all as specified and directed.

Repair of old existing unserviceable aluminium doors by adjusting/resecuring rubber beads, gasket beading etc complete all as specified and directed by Engineer-in Charge

S&F in repair 150mm floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor etc complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality fixed with oil putty to metal frame including hacking out old broken glass (in any description) from metal frame etc complete all as specified and directed.

S&F in repair Mortice lock of size 100mm with two levers(vertical type) mild steel body and fixed etc complete all as specified and directed.

S&F in repair Mortice lock of size 100mm with two levers(vertical type) brass body and fixed etc complete all as specified and directed.

S&F in repair 40mm dia cupboards knobs fixed with nut, screw and washer of mild steel bright finished etc complete all as specified and directed.

S&F in repair hasp & stapple 100mm mild steel wire type , stove enamelled black , including bolt to hinge plate and fixed and screws etc complete all as specified and directed.

S&F in repair extruded brass handle fabricated type polished of size 150mm etc complete all as specified and directed.

S&F in repair brass sliding door bolt of size 250mm and 12mm dia with sand or die-cast brass hasp, stapple (bolt type) and fixing bolt with rolled or srawn brass bolts and fixed etc complete all as specified and directed.

M&L for repair/ replacement of locking arrangement of mild steel cupboard/locker/ Almirah etc including necessarry stainless steel handle , MS rod with complete locking arrangement and making functionableetc complete all as specified and directed.

Treatement for sunken portion is as follows :- (a) Demolition of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. (b) Maintain the Sunken to a slope of 1:40 outward with 32mm dia GI pipe spout projecting at least 150 mm beyond outer face of wall. (c) Top of the sunken floor slabs shall be laid to a slope 1:40. The surface of RCC slab shall be made even and smooth by using extra cement while the concrete is still green. Concave fillet in PCC (1:2:4) type B0 of radius 75 mm shall be provided at the junctions of RCC slab and adjoining walls. (d) Floor and side walls upto the finished floor level shall be plastered with 15 mm thick CM (1:4) mixed with water proofing compound @ 3% by weight of cement. Over plastered surfaces, a layer of APP based polymeric membrane not less than 3mm thick, weighing not less than 3 kg per sqm, reinforced with polyster non- woven fabric (weighing not less than 150 gm per square metre) shall be laid by torch application. Side overlaps shall be 100mm and the ends laps shall be 150 mm and overlap joints shall also be sealed by torch application.(e) The sunken portion shall be filled with lean cement concrete (1:5:10), type E2 using 40 mm brick aggregate after carrying out satisfactory testing of CI pipes / joints and slabs / walls by filling water for 72 hours. The sunken portion of Nahani / floor trap and pipe joints shall be embedded in PCC (1:3:6) blocks. (f)32 mm dia GI spout shall be provided to drain out leakage, if any.

Supply only integral waterproofing compound

S&F Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (style), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front Face & 2mm Plan colour PVC sheet on back face, supplying & fixing in frame at site with particle board core as per specification & drawing.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain finish PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing

S&F Butt hinges 100mm long extruted aluminum alloy with galavanisied mild steel hing pin anodised and fixed etc complete all as specified and directed.

S&F Aluminum anodised, barrel tower bolts of extruded section and fixed 150 mm long etc complete all as specified and directed.

S&F extruded aluminium alloy handles 125mm size fabricated type anodized ISI marked etc complete all as specified and directed.

S&F mild steel butt hinges medium weight cold rolled of size 100mm, ISI marked etc complete all as specified and directed.

S&F Aluminium barrel tower bolt 300 mm long stove enamelled black with bright bolt & fixed etc complete all as specified and directed.

S&F Aluminium sliding door bolt with hasp,staple (bolt type) 300mm long not less than 12mm dia with and incl minimum of 06 bolt and nuts four on bolt plate and two on staple plate etc complete all as specified and directed

S&F mild steel Casement stays, size 300mm, with hinged joint and two plates, with studs etc complete all as specified and directed.

All as per item No 84.00 above but 250mm etc complete all as specified and directed.

S&F mild steel Casement stays, size 250/300mm, with hinged joint and two plates, with studs fixed to steel sashes,including necessary hole or welding etc complete all as specified and directed.

S & F Stainless steel Curtain rod not less than 20 mm dia with chromium plated including both sides finnials and bracket fancy type fixed in position by drilling holes in walls and fixed the brackers with rawl plug and steel screw etc compete all as specified and directed.

Taking down or up steel tubing and connections inculding cleaning for refixing or removal to store 15mm bore etc compete all as specified and directed.

S&F, jointing and testing 15mm dia bore galvanised iron tube medium grade with all fittings such as bends, elbows sockets, reduces etc and fixed to wall, ceiling or laid in floor with new fittings including cutting through wall floor etc compete all as specified and directed.

Refixing old steel tubing and connection in new or old position (walls,ceiling,floor etc) bore of pipe in 15mm dia etc compete all as specified and directed.

S&F in repair vitreous china squatting pan of Orrisa pattern size 580mmx440mm white with integral foot rest (excluding flushing cistern and flush pipe complete incluidng provision of lime/cement concrete bedding fixed etc compete all as specified and directed.

S&F in repair PVC flushing cistern low level 10 ltr cap with inlet ball valve float and handle syphonic action type incl brackets and flush pipe of polythene of low or high density ISI marked.etc compete all as specified and directed.

S&F repair vitreous china wash basin white of size 550mmx400mm fixed to granite etc including 32mm dia CP brass waste coupling fitting and union etc compete all as specified and directed. Note: Pillar tap shall be measured and paid separately

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm etc compete all as specified and directed.

S&F in repairs Brass chromium plated shower rose 125mm size fixed to 15mm bore pipe etc compete all as specified and directed.

S&F Brass Chromium plated Tubular Towel rail, 20mm dia, D type, 60 cm long between flanges fixed to wall etc complete all as specified and directed.

S&F in repair 15mm dia stop valve/angle valve of copper alloy fancy type chromium plated screwed down high pressure with crutch or butter fly handle screwed on both ends for iron pipe or for union fixed etc compete all as specified and directed.

S&F in repairs 15 mm bore fancy type long body bib tap, half turn, with wall flange, cast copper alloy with capstan heads, chromium plated, screwed for iron pipe or for brass ferrule, etc compete all as specified and directed.

S&F high density polythelene pipe (HDPE) of 32mm, pressure rating 6 Kgf/cm2 fixed to ceiling, floor etc complete all as specified and directed

S&F in repair 15mm dia bore cast copper alloy chromium plated fancy type pillar tap(Swan Neck) for with out cold & hot water etc compete all as specified and directed.

S&F 1000 Ltr capacity of rotational moulded polyethylene water storage tank (Cylindrical vertical with closed tap) hoisted and fixed in position including S&F 20mm float valve 20mm dia GI pipe medium grade washout pipe 450mm long with plug and 20mm dia GI pipe medium grade overflow pipe 600 mm long with fitting and including dismantling of tank etc complete all as specified and as directed by the Engineer-In- Charge.

S&F 500 Ltr capacity of rotational moulded polyethylene water storage tank (Cylindrical vertical with closed tap) hoisted and fixed in position including S&F 20mm float valve 20mm dia GI pipe medium grade washout pipe 450mm long with plug and 20mm dia GI pipe medium grade overflow pipe 600 mm long with fitting and including dismantling of tank etc complete all as specified and as directed by the Engineer-In- Charge.

S&F in repair 20mm ball valve with high pressure (PTMT) with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 20mm 210 gm. etc compete all as specified and directed.

S&F in repairs 20mm bore Gun Metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe and fixed etc compete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches or floors etc compete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, fixed to walls with Holder bat clamps of GI flat iron 25x3 mm etc compete all as specified and directed.

S&F PVC (SWR) bends 110mm dia any radius.etc compete all as specified and directed.

S&F PVC (SWR) junction single(Single T) equal or unequal with access door110mm dia.etc compete all as specified and directed.

S&F PVC(SWR) Vent cowl 110mm dia.etc compete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches or floors.etc compete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, fixed to walls with Holder bat clamps of GI flat iron 25x3 mm etc compete all as specified and directed.

S&F PVC (SWR) bends 75mm dia any radius.etc compete all as specified and directed.

S&F PVC (SWR) junction single(Single T) equal or unequal 75mm dia.etc compete all as specified and directed.

Supply and fix 110mm PVC (SWR) WC connector bent type all as specified and as directed.

Dismantling AC Pipe/ PVC pipes 110mm/ 75 mm diaetc compete all as specified and directed.

M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. etc complete all as specified and directed

S K BUILDERS (BID ID -3086237)

vandana enterprises (BID ID -3085925)

shiva construction (BID ID -3081391)

AARSINFRATECH (BID ID -3094094)

ALAKNANDA ENTERPRISES (BID ID -3094085)

GAR CONSTRUCTIONS (BID ID -3086941)

M/s ASK Enterprises (BID ID -3086802)

J.J.ENGINEERING (BID ID -3087695)