Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | LI₹24.4 LAccepted-AOC | LI | Accepted-AOC accept | |
| 2 | LII₹24.7 LRejected-AOC | LII | Rejected-AOC accept | |
| 3 | LIII₹25.0 LRejected-AOC BIDYAPUR NALBARI ASSAM | NALBARI | NALBARI | ASSAM | LIII | Rejected-AOC accept | |
| 4 | Rejected-Technical | - | Rejected-Technical non responsive | |
| 5 | Rejected-Technical CHINAPATTY H NO 359 CITY TOWN MAKUM P O P S MAKUM DIST TINSUKIA PIN 786170 | TINSUKIA | ASSAM | 786170 | - | Rejected-Technical not responsive |
Tender Value
₹23.6 L
EMD Value
₹47,292
Closing Date
20 Nov 2023, 3:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Executive Engineer, PWD, Dibrugarh, Moran, Lahowal
Executive Engineer, PWD, Dibrugarh, Moran, Lahowal Tingkhong Territorial Building Division, Dibrugarh
Upgradation of Principal room at Tinsukia Polytechnic, Makum
2023_PWBNH_33964_1
TSK/BLD/CS-01/23-24/C-1/06-A, dtd. 31/10/2023
Open Tender
Civil Works - Building
Item Rate
180 days
Tinsukia Polytechnic, Makum
Please refer Tender documents.
6 documents required · 6 mandatory
₹473
₹47,292
Yes
Executive Engineer, PWD, Dibrugarh, Moran, Lahowal
21 Aug 2024
16 Nov 2023
20 Nov 2023
16 Nov 2023
20 Nov 2023
16 Nov 2023
16 Nov 2023
Amount
12.31 : Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately): 12.31.1. : Flat surfaces
9.20 : Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.20.1. :- 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
9.27. : Providing and fixing wire gauge shutters using galvanized M.S. Wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 9.27.1. : 35 mm thick shutters 9.27.1.1. : with ISI marked M.S. pressed butt hinges bright finished of required size. 9.27.1.1.1. : Second class teak wood
9.43. : Providing and fixing 18 mm thick, 150 mm wide pelmet of coir veneer board ISI marked IS : 14842, including top cover of 6 mm coir veneer board, nickle plated M.S. Pipe 20 mm dia. (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. Flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.
17.31 : Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
17.33. : Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
17.73 : Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 17.73.2. : 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.
13.4. : 12 mm cement plaster of mix : 13.4.1. : 1:4 (1 cement: 4 coarse sand)
13.41. : Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 13.41.1. : New work (two or more coats) over and including water thinnable priming coat with cement primer
13.45 : Finishing walls with textured exterior paint of required shade : 13.45.1. : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm
21.1 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : 21.1.1. : For fixed portion
21.1.2.1. : Powder coated aluminium (minimum thickness of powder coating 50 micron)
4.1. : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 4.1.3. : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
21.2.1. : Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side
21.3.2. : With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
13.48. : Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : 13.48.1. : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm.
15.2. : Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 15.2.1. : Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
11.47. : Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). 11.47.2. : Size of Tile 600x600 mm
8.31. : Providing and fixing Ist quality ceramic glazed wall tiles conforming toIS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
9.7.5.3. : Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side, Grade I, Type II IS: 12823 marked
9.20.1. : 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
9.1.3. : Kiln seasoned and chemically treated hollock wood
9.47.2. : Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets :
Furniture Items Table, Chair etc. (Rate should bequoted above / below in percentage basis / As per for example : If one quotes rate 1% above, then the rate will be 1.01 and if one quotes rate 1% below, then the rate will be 0.9, for As per, rate should be quoted as 1)
Any other unseen item of works which may be required at the time of execution. (Rate should bequoted above / below in percentage basis / As per for example : If one quotes rate 1% above, then the rate will be 1.01 and if one quotes rate 1% below, then the rate will be 0.9, for As per, rate should be quoted as 1) on CPWD DSR for 2021 and 2018 [Electrical] for Civil/Sanetery water supply, Electrical and Furniture Items.
M/S PAPORI ENTERPRISE
JAYANTA DEKA
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .