Providing Fire Fighting, STP and ETP Arrangements for the work of Construction of Maternity and Child Health and Accident Emergency Care Unit buildings in Government Hospital at Tiruchendur in Thoothukudi District

Amount

SUMP AND PUMP ROOM Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in hard rock requiring blasting inclusive of shoring, strutting, bailing out water wherever necessary and depositing the excavated earth with an initial lead of 10 mts,, and initial lift of 2 mts., within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand (M-Sand) and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Brick work in Cement Mortar 1:6(one cement and six crushed stone sand ( M-sand) with best quality of Fly ash bricks of size 230mmX110mmX70mm including pointing with same mortar, levelling and curing, etc., complete complying with standard specifiction.

In Ground Floor

Brick work in Cement Mortar 1:5 (one cement and five crushed stone sand ( M-sand) with best quality of Fly ash bricks of size 230mmX110mmX70mm including pointing with same mortar, levelling and curing, etc., complete complying with standard specifiction

In Ground Floor

Supplying and erecting steel centering including supports for plain surfaces for reinforced cement concrete work such as column footings, column pedestals, grade beams, plinth beams, staircase steps, critical piers, etc., which require only nominal stutting using mild steel sheets of size 90cm x 60cm of B.G.10 stiffened with welded mild steel angles of size 25 mm x 25 mm x 3 mm boarding laid over silver oak (or) country wood joists of size 10 cm x 6.5 cm spaced at about 90 cm centre to centre and supported by casuarina props of 10cm to 13 cm dia spaced at 75 cm centre to centre at suitable intervals etc., complete complying with standard specifications. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including supports and strutting upto 3.29m high for plain surfaces such as RCC slab, beams, TEE or Ell beams, Lintels, staircase beams etc., with all cross bracings using mild steel sheets of size 90cm x 60cm of B.G.10 stiffened with welded mild steel angles of size 25 mm x 25 mm x 3 mm boarding laid over silver oak (or) country wood joists of size 10 cm x 6.5 cm spaced at about 90 cm centre to centre and supported by casuarina props of 10cm to 13 cm dia spaced at 75 cm centre to centre at suitable interval. etc., complete complying with standard specifications. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as sides and bottom of RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

Providing and laying in position, standardised concrete Mix M30 grade (Up to 10KM aerial distance from sea water front )in accordance with IS 456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of work with minimum cement content of 400 Kg/m3 and maximum water cement ratio of 0.45 including admixture (Plasticiser / super plasticiser ) in recommended proportions as per IS : 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 Cum) 7730kg. of 20mm machine crushed stone jelly and with about (3.3cu.m.) 5156kg. of 10-12 mm machine crushed stone jelly with about 4.79 Cu.m. ) 7670kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also

including laying , vibrating with mechical vibrators, finishing curing etc., and providing fixtures like fan clamps in the RCC floor/ roof slab wherever necessary without claiming extra ,etc., complete complying with standard specifications and as directed by the departmental officers.The coarse and fine aggregates to be used should comply with the requirements of IS standards.(No Separate payment will be made by the department for the excess usage of materials)

In Foundation and Basement

In Ground Floor

Supplying,fabricating and placing in position Mild/Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification.(The contractor will have to make his own arrangements for the supply of MS plain rod / RTS rod and GI binding wire)

Plastering with Cement Mortar 1:3 [One Cement and Three Plastering sand (P-sand)] 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finishing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Supplying and erecting pull and push type Rolling Shutters of manually operated with ISI mark of approved size and section using 18gauge G.I Sheet The shutter shall be painted with one coat of red oxide primer and the rate is inlcusive of Hood cover, runners, GI wire, transportation charges etc., complete complying with standard specification.

Manually Operated

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three P-Sand) 10mm thick mixed with bonding agent cebex112, Zydex-zycrete 2x or other Equivalent compound conforming to BIS at 200 ml of one cement bag (50 Kg) for increased workability and air entrainment including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five P-sand), 12mm thick mixed with bonding agent cebex112, Zydex-zycrete 2x or other Equivalent compound conforming to BIS at 200 ml of one cement bag (50 Kg) for increased workability and air entrainment including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) (M-Sand)12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Providing granolithic floor finish of the required thickness with plain cement concrete 1:2:4 (One Cement, Two crushed stone sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers) a) 40 mm thick

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is

provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and dditional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter to conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Single leaf 1.00 X2.10m (Fully Sheeted)

Fabricating, Supplying and fixng in position of steel sheeted windows (Two Leaves) with the following specifications. Outer frames of windows made of 'Z' section F7D of size 33 x 25 x 3mm at 1.419 kg/ m and mullion 'J' section (F4B) of size 46x25x3mm at 2.28kg/m and shutter section of made of F7D of 33x25x3mm at 1.419 kg/m as specified in IS 7452/1990. Each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance. The panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. Horizontal stiffeners using 18x5mm MS Flat at 0.70kg/m at 3 Nos. for each shutter and additional diagonal stiffners of the same MS flats at all the four corners of each shutters to the suitable length welded to the shutters,

for holding the CR Sheets in position firmly.2 numbers of sturdy hinges and one number of handle-cum-latch of special type made with 18x5mm MS flats are revetted to the shutters at an appropriate height in window. suitable opening is left for its easy operation. a stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle. each window shutter having an adustable stay made out of 18 x 5mm at 0.70 kg/ m MS flat of lenght 320mm with three adjustable position.

A matching peg is provided in the outer frame of the window at suitable place. 4 Nos. of hold fasts of 120mm length spliced at the ends are welded to the outer frame of the window by using MS flat of 18x5mm at 0.70kg/m, welded to the shutter at two place equivalent from each from top and bottom of the shutter.An MS square bar of 12mm size is welded to the inner face of the window at an equal interval not exceeding 100mm edge between them. All members are painted with one coat of anti-corrosive red oxide primer as directed by the departmental officers. All sections should be in confirmed with IS 7452/1990.The cost includes cost of all materials, labour charges and other incidental charges, etc., complete.

Two leaves-1.20x 1.30 m

Painting two coats of newly plastered wall surface with ready mixed plastic Interior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position best approved of BIS quality of PVC rain water down fall pipes having a working pressure of 4 kg/cm2 including cost of necessary PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cost of removable of iron grating. The PVC pipe shall be fixed in wall with Special type of 'U' clamp at the centre of the pipe line in addition to those for more than 3m pipe length etc., complete complying with standard specification.

110mm dia

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete complying with standard specifications

Making through holes in Plain or Reinforced Cement Concrete with Diamond Core Drilling System by using BOSCH power tools of following diameter - Depth per cm

FIRE FIGHTING SYSTEMS Supply, erection, testing and commissioning of Fire Fighting Application Horizontal Centrifugal Type Pump Rated for 2280 LPM at 70 metres head with Electrical Motor of 60 HP of 415 volt 3 phase connection complete with base plate and accessories. (Make: Kirloskar or Equivalent). The rate inclusive of necessary vibration, bad mounting etc., as per standard method as directed by the Deparmental Officers.

Supply, installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of following and complete in all respects as required. a. End suction, top discharge centrifugal pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg. / sq. cm at highest and farthest outlet at specified flow of 2280 LPM at 70m head conforming to IS 1520. b. 68 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. Auto starting mechanism, 12 volts / 24 volts electric starting equipment like self motor, dyanamo, solenoid switches etc. c. 110 litres capacity diesel tank mounted over stand fabricated using 25mm x 25mm x 6mm size MS angle, providing with level indicator, inlet port,

outlet port, drain port and diesel return line port and fuel pre-filter, after filter etc. (Make: Kirloskar / Equivalent). d. Exhaust system having flexible metallic mufler, 100mm dia MS heavy pipe extended upto 1m, outside pump house duly insulated with 50mm thick glass wool with 1mm thick aluminium sheet cladding, residential silencer with necessory MS support arrangements from wall or ceiling as per site condition.e. Dash board consisting the instruments like temperature gauge, galvano type DC Ammeter, lubricant oil pressure gauge, ignition switch, emergency stop and all other protection equipment as per specification, stop seleneid for auto stop in the event of fault with audio indications, painted with post office red colour etc., as required. f. 12 V / 24 V storage battery, maintenance free tape, 180 AH rating,

MS fabricated common base plate, coupling guard, foundation bolts etc., as required. g. Positioning the diesel engine driven fire pump over cement concrete foundation using suitable size anti-vibration mounting arrangement. All works carried out as per standard methods and as instructed by the manufacturer and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent)

Supply, erection, testing and commissioning Mono Block type Fire Fighting Pressurisation Pump of 180 LPM 110 metres head at 10 HP with suitable base frame including necessary vibration bad mounting etc., including conveying, fixing and incidental charges., etc., complete as per standard specification and as directed by the Departmental Officers.

Supply and laying of following sizes of Armoured Aluminium Cables for electrical motor, control panel, pressure switch, jockey motor etc.. The rate inclusive of all incidental charges, neccessary scaffolding and redoing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: POLYCAB / PARACON / FINOLEX / EQUIVALENT.

3 core 10 sq.mm. armoured aluminium cable

2 core 1.5 sq.mm armoured multi strand aluminium

Supply and laying of following sizes of Armoured Aluminium / Copper Cables for electrical motor, control panel, pressure switch, jockey motor etc., all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: POLYCAB / PARACON / FINOLEX / EQUIVALENT.

10 core 2.5 sq.mm. armoured Copper cable

Earthing arrangements with GI Earth Plate including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work, re-filling the sides of foundation with excavated earth as per the standard specification and as directed by the Departmental Officers.

Supply, erection, testing and commissioning of following MS „C‟ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table „E‟, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.

200mm nominal dia

150mm nominal dia

100mm nominal dia

80mm nominal dia

65mm nominal dia

50mm nominal dia

40mm nominal dia

25mm nominal dia

Wrapping and Coating Anti-Corrosive Treatment for under ground MS pipe having one coat of anti-corrosive metal primer, one layer of asphalt tar tape wound over the MS pipe as per standard methods as per standard specification as directed by the Departmental Officers

200mm nominal dia

150mm nominal dia

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table „E‟, gaskets, bolts & nuts including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT

200 mm dia

150 mm dia

100 mm dia

80 mm dia

Supply, erection, testing and commissioning of Gun Metal Gate Valve of size 50mm dia size including necessary MS flange of table „E‟, gaskets, bolts & nuts etc., installed at pump house delivery line for the purpose of priming water to suction line including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.Make LEADER / EQUIVALENT.

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Nonreturn valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table „E‟, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers

200 mm dia

150 mm dia

100 mm dia

Supply, erection, testing and commissioning of following sizes of Heavy Duty Foot Valve including all accesories, such as, MS flange of table „E‟, gaskets, bolts & nuts, etc., installed at end of 150 / 200mm dia suction pipe line at sump including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete and as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT

150 mm dia

100 mm dia

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line Indfoss or Donfoss including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motor including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., completed as per standard specification and as directed by the Departmental Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT.

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: H-GURU / ISI MAKE / EQUIVALENT

Providing, fixing pipe supports from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening, arrangement design of hanger and should confirm with specification. 100mm dia

Supplying and fixing in position of P.V.C water storage tank of best approved quality and brand with the capacity of 1000 Litres with accessories including giving necessory connections etc., complete as directed by the departmental officers. ( The P.V.C. water storage tank should be got approved by the Executiove Engineer before use on works.)

Priming Tank mounted with the supporting arrangement fabricated using MS angle for the height of 3 metres from the floor level, inlet, outlet, and drain arrangements inside the fire fighting pump room, as directed by the Departmental Officers.

Supply and fixing in position of 12 Volt 180 AH Lead Acid, Sealed Maintenance Free (SMF) batteries with connecting leads, lugs terminal post, etc., as per standard methods and including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT.

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application Hose of 63mm dia of 15 metres length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR/ LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT

Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT

Supply, erection, testing and commissioning of Fire Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX / EQUIVALENT

Supply, erection, testing and commissioning of fire fighting application monoblock motor pumpset of 900 LPM at 40 metres head to develop 3.5 kg/sq.cm at the heightest and farthest hydrant point to make 30 m water jet at the time of fire fighting emergency cicumstances, coupled with 11 KW / 15 HP rated three phase 414 volts, 50 Hz, 2880 rpm electrical motor the pump with cast ron body, bronze impeller, rope gland packaging, suction size of 80 mm dia. delivery size of 65 mm dia., including the cost of foundaton concrete anti vibration mounting, rain safety hood and etc. complete as directed by the Departmental Officers (Kirloskar make KDS 1555+ or Equivalent)

Push Button - 1 set g. Add On Block, Terminal Block, Power Wiring, Control Wiring, Connectors, Cable Lugs, Slotted Cable Cover The above panel mounted on wall using anchor fasteners bolts, plugs, incoming and outgoing cable connection and all works carried out as per standard methods and as directed by the Departmental Officers.

Supply and laying of 4 core 10 sq.mm. armoured copper cable for power wiring to the Terrace Pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers.

Supply and laying of 2 core 1.5 sq.mm. armoured copper cable for control wiring to the Terrace Pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers

Supply and fixing nominal bore quartized bulb type sprinkler bulb 68 Deg C fast response pendent type including GI collar for each sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, shellac etc., as per standard methods and including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, Installing, testing and commissioning of Stainless Steel Corrugated Flexible Braided Pipe (Hose) for dropping sprinklers below false ceiling. Pipe shall be 16 bar pressure rating and 1000mm long, 25mm dia with union / reducer, collar, clamps, etc. It shall have UL listed and FM approved.

Supplying and installing of approved type Rosette Plates (Recessed Type in Two Pieces) for sprinklers below false ceiling area. The Rosette shall be fabricated by MS plate of 2mm thick and the finish shall be powder coated and colour, as directed by the Departmental Officers.

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply, installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS juction box / false ceiling using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers. (Make: Apollo / Equivalent)

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers. (Make: Ravel / Equivalent)

Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers (Make: Ravel / Equivalent)

Supply and laying of following sizes of Armoured Aluminium Cables for electrical motor, control panel, pressure switch, jockey motor etc.. The rate inclusive of all incidental charges, neccessary scaffolding and redoing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make:POLYCAB/PARACON/FINOLEX /EQUIVALENT.

2 core 1.5 sq.mm armoured multi strand aluminium

PART "P" CONFERENCE TYPE PUBLIC ADDRESS SYSTEM, PROJECTOR AND MOTORIZED SCREEN

Wall Speaker 15W

PA Mixer Amplifier 120W

Cordless Mic UHF

NTI Supply & Installation of Gun Metal Ball Valve of size 25 mm dia size including necessary Fittings

3c x 35 Sqmm Aluminum Armoured Cable for Main Electrical Pump

Supply, installation, testing and commissioning of Micro Processor based conventional 32 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230 / 24 volt SMPS unit, 2 Nos. of 12 volt 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers.

Supply & Installation of in position the sign board of "EXIT " with arrow to be placed at walking pathways by fixing on walls to direct occupants to outside the buliding in an emergency. The Exit sign board will be autoglow photoluminiscent type which will glow at dark.(Single Side indication)

Supply & Installation of Fire Escape Route Plan Laminated Board Auto Glow Print to be placed at each floor by fixing on walls to direct occupants to outside the buliding in an emergency. The Fire Escape Route Plan will be autoglow photoluminiscent type which will glow at dark.(Single Side indication)

Supply & Installation of Power Supply for Hooter

PLAIN CEMENT CONCRETE 1:2:4 [one cement, two crushed stone M-Sand and four hard broken stone jelly] using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Machineries for STP Design Fabrication, Supply and erection of bar screen made of MS 10mm square bars to suit the channel. Inner size of channel 1000mm , wide 900mm liquid depth and 1200mm length. The MS 10mm square bars should be properly epoxy coated to avoid the rusting of bars. The spacing between the square bar is 5mm, so that the particles above 5mm will be retained in the entry channel and will be cleared by hand rac manually. The bar screen should be kept at an inclination of 60o. The bar screen is fixed at site, inside the channel with a groove like arrangements, so that bar screen could be removed for maintenance purpose. The cost includes cost of MS bars, fabrication charges, Epoxy painting charges and fixing at site transport charges to site., etc., complete

Design Supply and erection of Tube Settler feed pump with motor with the capacity of 7.50 m3 /hr as per the design. The type of the pump is submersible sewage disposer , Non clog. The pump make is kirloskar/CRI/equivalent, The capacity of the motor is 2.0 HP. The type of the motor is TEFC, IP55, CLSS-B insulation, suitable for 3 phase supply, 440V, 50HZ .Motor make is Kirloskar/CRI/ Equivalent. Necessary base frame, foundation bolts nuts are provided to fix the coupled pump set above the foundation bed. The cost includes the pump, motor, Stand by pump and motor, base frame, foundation bolts, labour charges, erection charges, transport charges etc., complete.

Design Supply and erection of Coagulant dosing pump with the capacity of of 0-6 liters per hour @ 4 kg/cm2, 0.16 HP with electronic driven construction of pump is Polypropylene . The pump is fitted Base frame necessary bolts and nut . The capacity of the tank 100 liters with HDFE. The pump is fitted with a suction and delivery line. Necessary foot valve, level indicator is provided with the pump. Including the suitable Agitator for dosing pump The cost includes the cost of the pump, tank, foot valves, delivery and suction tubes of standard length, Agitator, labour charges, transport charges, erection charges etc., complete.

Design Supply and erection of Flocculent dosing pump with the capacity of 0-6 liters per hour @ 4 kg/cm2, 0.16 HP with electronic driven construction of pump is Polypropylene . The pump is fitted Base frame necessary bolts and nut . The capacity of the tank 100 liters in HDPE. The pump is fitted with a suction and delivery line. Necessary foot valve, level indicator is provided with the pump. Including the suitable Agitator for dosing pump The cost includes the cost of the pump, tank, foot valves, delivery and suction tubes of standard length, Agitator, labour charges, transport charges, erection charges etc., complete.

Design Supply and erection of air blowers Ring Blower with electrical Motor, 16 m3/hr, 1 HP motor . Air blower with motor are provided for one number for operational and one number for standby. The Air blower make is of Raico/Equivalent to suit the design requirements. The Air blower with motor is fixed in a base frame. Necessary foundation bolts, nuts are provided to fix the total coupled assembly of Air blower and motor in the concrete bed. The cost includes the cost of Air blower, stand by Blower, base frame , diffusers, foundation bolts, erection charges, transport charges, labour charges., etc., complete.

Design, Fabrication, supply, erection of tube settler media with PVC 1000mm depth 1.1 mm thickness in hexagonal chevron shaped fixed with 60 degree slope in tube settler tank (2.5 m3) including the cost of tube settler media, erection charges , transport charges, labourcharges.etc., complete

Design Supply and erection of Sand Filter feed pump with motor with the capacity of 7.50 m3 as per the design. The type of the pump is horizontal, Centrifugal, flexible coupling drive arrangement. The pump make is kirloskar/CRI/equivalent; The capacity of the motor is 3 HP. The motor type suitable for 3 phase supply, 440v, 50hz . Motor make is Kirloskar/CRI /Equivalent. Necessary base frame, foundation bolts nuts are provided to fix the coupled pump set above the foundation bed. The cost includes the pump, motor, Stand by pump and motor, base frame, Motor Guards, foundation bolts, labour charges, erection charges, transport charges etc., complete.

Design Supply and erection of Oxidant dosing pump with the capacity of of 0-6 liters per hour @ 4 kg/cm2, 0.16 HP with electronic driven construction of pump is Polypropylene. The pump is fitted Base frame necessary bolts and nut . The pump is fitted with a suction and delivery line. Necessary foot valve, level indicator is provided with the pump. Including the suitable Agitator for dosing pump The cost includes the cost of the pump, tank, foot valves, delivery and suction tubes of standard length, Agitator, labour charges, transport charges, erection charges etc., complete.

Design Supply, fabrication and erection of Multi graded Sand filter unit with 915mm dia and 1828 mm height. Multi graded Sand filter is a vertical, cylindrical vessel made out of FRP . The inlet pipe inside the vessel is designed to have a bell mouth arrangements for liquid/water distribution, so that the filter media is in position & will not get disturbed. The bottom collection system is provided with header and lateral pipe arrangements with necessary holes. The filtered water is collected thro this header lateral pipes, will flow out to outlet pipes and vice versa. The filter media consists of Multi graded sand filled over & under bed media of pebbles and gravels. The size and height of the filter media is as per the design and standards. The joints are properly vessel (Multi graded Sand Filter ) is supported by FRP legs, thereby fixing the vessel with foundation bolts properly in the concrete foundation bed. The cost includes the cost of materials bolts, nuts and washers, filter media, foundation bolts fabrication charges, welding charges, erection charges, transport charges and painting etc., complete.

Design Fabrication, Supply and erection of Bag filter with 20 micron with 10 m3/hour with Stainless Steel Gad ridges. The cost includes cost of bag filter, stand , fabrication charges, and fixing at site transport charges to site., etc., complete

Design Supply, fabrication and erection of Eco Ozotex with Ozone Generator includes the ozone recirculation pump in 4 m3 /hour. The type of the pump is horizontal, Centrifugal, Non clog, self priming flexible coupling drive arrangement. The pump make is kirloskar/CRI/equivalent, The capacity of the motor is 1 HP. The type of the motor is TEFC, IP55, CLSS-F insulation, suitable for 3 phase supply, 440V, 50HZ . ozone generator with a capacity of 150gms / hour with oxygen concentrator, including the cost of epoxy coating for ozone reactor tank, water ozone mixing equipments The cost includes the ozone generator, oxygen generator, ozone recirculation pump, motor, Stand by pump and motor for ozone recirculation pump, base frame, Motor Guards, foundation bolts, labour charges, erection charges, transport charges etc., complete.

Design Supply, fabrication and erection of Activated Carbon filter unit with 915mm dia and 1828 mm height. Activated carbon filter is a vertical, cylindrical vessel made out of FRP The inlet pipe inside the vessel is designed to have a bell mouth arrangements for liquid/water distribution, so that the filter media is in position & will not get disturbed. The bottom collection system is provided with header and lateral pipe arrangements with necessary holes. The filtered water is collected thro this header lateral pipes, will flow out to outlet pipes and vice versa. The filter media consists of activated carbon filled over & under bed media of course silex. The size and height of the filter media is as per the design and standards. The joints are properly vessel (Activated carbon filter) is supported by FRP legs, thereby fixing the vessel with foundation bolts properly in the concrete foundation bed. The cost includes the cost of materials bolts, nuts and washers, filter media, foundation bolts fabrication charges, welding charges, erection charges, transport charges and painting etc., complete.

Design Supply and erection of Back wash pump with motor with the capacity of 7.50 m3 /hr , head of 3m as per the design. The type of the pump is horizontal, Centrifugal, Non clog, self priming flexible coupling drive arrangement. The pump make is kirloskar/CRI/equivalent, The capacity of the motor is 3 HP. The type of the motor is TEFC, IP55, CLSS-F insulation, suitable for 3 phase supply, 440V, 50HZ . Motor make is Kirloskar/CRI/Equivalent. Necessary base frame, foundation bolts nuts are provided to fix the coupled pump set above the foundation bed. The cost includes the pump, motor, Stand by pump and motor, base frame, Motor Guards, foundation bolts, labour charges, erection charges, transport charges etc., complete

Design Supply and erection of Treated tank recirculation aeration Pump of capacity of air flow 10m3/hr as per design the treated tank recirculation aeration pump submerciblenoiceless jet aerator for mixing ozone and oxygen the pump make is toshio or Kirloskar or CRI or equlant to suit the above said air flow rate the pump cupled with noiceles holder air inlet duck gas mixer chamber and divergvent the purpose of the pump is to recirculation for treated water the type of the motor is TEFCIP 55 CISS-B insulation suitable for 3phase supply 4V 50 HZ. The capacity pump is 1HP the cost includes cost of pump base frame foundation bolds labour charges for erection, transport chanrges etc., complete.

Design Supply, Fabrication and erection of piping for sewage treatment plant of capacity 150 m3. The piping work consists of 1) Suction lines from Equalization tank, delivery lines to Tube settler thro' raw sewage transfer pumps. 2)Pipe lines for Blowers to Equalization tank Both MS and PVC pipes with necessary valves, pressure gauges are used as per the design and suit the flow rate. 3)Pipelines from Clarifier tank Bag filter and Multigraded sand filter 4)Pipe line from multigraded Sand filter to Ozone reactor and Ozone reactor to Activated Carbon Filter 5) Pipe line from Backwash pump to Mutigraded filter and Activated Carbon filter 6) Necessary pipe lines , valves, pressure Gauge for filters, flow meters for tube settler feed, Sand filter , Activated Carbon filter, float level switch The total piping network as given above, is within the sewage treatment units. The cost includes the cost of pipes (MS, UPVC and 1" dia to 3"dia), Specials, valves, pressure gauges, flow meters, pipe fittings, fabrication charges, labour charges, transportation charges etc, complete.

Providing and Fixing of Liquid Level Controller at all Tanks. Including suitable Electrical Panel. Suitable Cables and all other necessary accessories etc., Complete. Input Voltage : 220V AC/50 Hz ( Other Input Voltages on request) Motor Protection : Voltage Variation +/- 20%, Dry Run Condition 60 Sec Delay after return to normal line voltage and power on. Motor Trip Delay : 45 Sec after Dry Run LED Indications : Sump and tank level indication on the facia. Hi/Low/Normal Voltage indication, Flow indication, Pump Motor On/Off /Trip. Auto: Pump Motor switched on automatically when level falls below set low. Manual : Auto / Manual Switch for manual operation of pump motor. Audio Alarm : Audio Alarm on Dry Run. Mute : Feather touch Push-button to silence the Alarm Output contact rating : One N/O Contact for DOL Two N/O, N/C Contacts for Starters Level Sensing Technology : Current loop with Cyclic Sampling. This ensures long sensor life. Sensors : Standard Conductive type. (Fit for 150 m3 STP)

Design, Supply and Erection of Raw Sewage pump for old septic tank with the capacity of 20 M3 / Hr, head of 6 m as per the design. The type of the pump is Vertical, Centrifugal, Non clog, Submersible pump. The pump make is Kirloskar /CRI/ Lubi / equivalent. The capacity of the pump is 2.0HP. The type of the pump is CLSS-F insulation, suitable for 1 phase supply, 220 V,50HZ. Necessary base frame, foundation bolts, nuts are provided to fix the pump set above the tank bed. The cost includes the pump,starter,cables, if any foundation bolts, labour charges, erection charges, transport charges etc., complete., ( FOR SEPTIC TANK TO STP TRANSFER PURPOSE)

Design, Fabrication, Supply and Erection of 3” PVC Pipe Materials, 2’’ NRV, Fittings with necessary Solvents, Teflon taps of required from Raw Sewage pump to Treatment plant collection tank as per design. . The Pipe sizes are as per the design and suitable for electrical motors fixed in the Sewage treatment plant. No lighting points are considered. The cost includes excavation, back filling, the cost of Pipes, fittings, accessories, , labour charges etc., Complete( FOR SEPTIC TANK TO STP TRANSFER PURPOSE)

Machineries for ETP Design fabrication, supply and erection Bar screen 10mm square bars to suit the channel. The SS square bar should be properly epoxy coated to avoid the rusting of bars. The spacing between the square bar is 5mm So, that particulars above 5mm will be retained in the entry channel and will be cleared by hand rac manually. The bar screen should be kept at an inclination of 60⁰. The bar Screen in fixed at site, inside the channel with a groove like arrangements, so that bar screen could be removed for maintenance purpose. The cost includes cost of, Ms bars, Fabrication charges, Epoxy painting charges and fixing at site transport charges to site., etc., complete.

Design, supply and erection of Neutralization or Precipitation tank for 2 m3 flow per hour with Dosing System for Oxidant dosing and suitable agitator , base frame, foundation bolts, labour charges, erection charges, transport charges precipitation tank etc., complete the rates

Design Supply, fabrication and erection of on line disinfection for effluent with Ozone in Ground Level Reactor including submersible Mixing arrangement @ the pump make is CNP / Toshio Equivalent, The capacity of the motor is 1 HP. The type of the motor is Self aspirating, non clogging with SS304 impeller , and SS 420 Shaft, suitable for 3 phase supply, 440V, 50HZ including the cost of water ozone mixing equipments with level gauge, safety valve includes the ground level reactor, motor Submersible mixing unit base frame, Motor Guards, foundation bolts, labour charges, erection charges, transport charges etc., complete.

Design, Supply of Ozone Generator with Capacity of 10 gm/ hour with oxygen Concentrator, including the cost of Ozone Generator, Oxygen Concentrator and Control Panel etc. Complete

Design, Fabrication, supply, erection of electrical panel board with necessary starters, main switches, voltmeter, ammeter, and electrical cables of required sizes from pumps to panel board as per design, The size of panel board is approximately 2 feet x 2 feet, fabricated with Ms sheets and powder coat. Necessary provisions are given in the panel board for main switch, starters, switches, voltmeter ammeter as per the design to suit Effluent Treatment plant. The cables are run from panel board to the all pumps and other electrical accessories such as level switches dosing pumps Pumps, mixing units etc complete., the cable sizes are as per the design and suitable for electrical motors fixed in the effluent treatment plant. No lighting points are considered. The cost includes the cost of panel board, starters, switches, voltmeter, ammeter, main switch, cables for motors, labour charges etc., complete.

Supplying and fixing mild steel iron grill for Windows Ventilators and grill gate etc., including one coat of red oxide primer using M.S. angle of size 40x40x6mm and grill using 20x6mm MS flat and necessary hold fast with M.S. angle of size of 40x40x6mm - 230mm long spliced at end is to be provided appropriate places for fixing the grill etc complete complying with standard specification. The type design for the grills should be got approved by the departmental officers before execution.

vivek vijay and company (BID ID -1216111)

Smart Infratech Developers (BID ID -1216776)