SPECIAL REPAIR/ REPLACEMENT TO BUILDING NO P-161 AND CERTAIN REVENUE WORKS AT AFS AMLA

Amount

B/R Portion Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as directed.

M&L for roughening the existing plain concrete floor surface by using needle hammer and cleaning the surface neatly using wire brush including disposal of rubbish out of premises and applying cement slurry in ratio 1:1 (1 cement : 1 sand) over roughened surface to receive screed bed mortar for laying tiles complete all as specified and directed.

Taking down in cement or cement lime plaster any description, on brick or stone wall etc., including raking out joints hacking for key,scrubing down with water etc., complete all as directed.

Taking down 30mm thick (Aprrox) PCC concrete padding, brick coba of any thickness on top of roof slab including taking down existing plaster work, water proofing treatment by chiseling the existing bituminous sand surface, cleaning the surface by removing bituminous coating and disposing off the rubbish materials to a distance not exceeding 50m metres complete all as directed.

Cutting out cracks to 'V' section in existing roof or terraces, cleaning out, wetting grouting with cement and sand slurry 1:3 mixed with integral water proofing complete all as specified and directed.

M&L for cutting holes into the brick walls built in cement mortar for inserting holdfasts or lugs to a depth exceeding half brick but not exceeding one brick thick from the face of jamb of wall and making good dismantled portion in cement concrete 1:2:4 (type B-1) or cement mortar 1:3 as required complete all as specified and directed.

Demolition of brickwork built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc., but excluding ashlar facings all as directed.

Demolition of plain cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling of boarding as in shleves of cupboard including battens etc of any description, fixed in any position with nails all as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. from any position complete all as specified and directed.

Taking down chowkats or frames of any description with shutters (without taking off shutter from the frame) of size exceeding 1.5 Sqm and not exceeding 4.0 Sqm each complete all as directed.

Taking down shutters of any description exceeding 1 Sq.m and not exceeding 2 sq.m each complete all as directed.

Taking down and refixing of shutters of any description in same opening of size exceeding 1 Sq.m and not exceeding 2 S.qm each including easing and adjusting, refixing builders hardware as required, and renewal of unserviceable screws, etc., complete all as directed.

M&L for providing, plain cement concrete 1:2:4 type B0 using 12.50mm graded aggregate as in coping and the like including formwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L Fly ash brick 75 kg/cmsq compressive strength. Modular size, is slaight or curved on plan exc. 6 metre mean radius built in cement mortar 1:4 complete all as specified and directed.

M&L Fly ash brick 75 kg/cmsq compressive strength. Modular size , is straight or curved on pian exc. 6 meter mean radius built in cement mortar 1:6 all as specified and as directed.

S&F 35mm thick, second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats complete all as specified and directed.

S&F 35 mm thick factory made second class hard wood rail and style plain framed panelled shutter (two panels) with lock rail and panel of 9mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The Size of rail and stile as per IS 1003 (part-I), kiln seasoned and chemically pressure treated and fitted to chowkhats complete all as specified and directed.

S&F 200mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt all as specified and direcetd.

S&F 250mm long, mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate all as specified and directed.

S&F of 300mm, Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F 150mm long mild steel pressed handles, oval type, stove enamelled black all as specified and directed

S&F in repairs for 20mm dia Harrison rails of anodized Aluminium alloy with fixing brackets, stops, rollers etc. complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60 cm long between flanges all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F of pressed steel door frame of size 125 mmx 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., complete all as specified and directed.

S&F powder coated aluminium frame for doors, windows, ventilators, partitions with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

S&F for 4mm thick, Fibre Cement Boards (Eaves boards) fixed/ inserted into GI/MS framework with screws complete all as specified and directed.

M&L for providing cement concrete 30mm thick PCC 1:2:4 type B-0 (12.5mm graded aggregate) as in padding on roofs slab to receive water proofing treatment, laid to required slope, finished even and smooth without using extra cement including mixing of integral water proofing compound as per manufacturing instructions complete all as specified and directed. [Note: Water proofing compound will be measured and paid separately under respective item of work].

Supply only integral water proofing compound

M&L for cleaning of roof surfaces and applying a coat of oil base bituminous primer @ 0.30 lit per sqm including laying of APP based polymeric membrane weighing not less than 3.00 kg/ Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt, not less than 150gms/sq. m) laid on primed surface by tension application and finally applying two coat of solar reflective bituminous aluminium paint @ 0.15 ltr/sqm on each coat the top of membrane surfaces and carrying out test by flooding water for 24 hrs to checking any leakage & seepages and rectifying the same to the entire satisfaction of GE complete all as specified and directed.

M&L for providing, plain cement concrete 1:2:4 type B1 using 20mm graded aggregate as in roof kerbs or mud stops, rounded or chamfered on edges including necessary formwork complete all as specified and directed.

S&F in repair 9mm thick, prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with aluminium fame including provision of suitable aluminium beading complete all as specified and as directed.

S&F in repair 12mm thick, prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination, fixed with aluminium fame including provision of suitable aluminium beading complete all as specified and as directed.

M&L for granite (of any type) 16-18mm thick (table rubbed and polished) in around column, vertical surfaces flat or in curve shape, steps, jambs, pillars, window-cill, cooking platforms and like in cement mortar (1:4) 15mm thick bedding/backing including pointing in white cement (1:2) using marble dust with admixture of pigment or by required approved adhesive with proper clamping arrangement and match with shade of granite all as specified and directed complete.

M&L for 75mm thick Plain Cement Concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection, surface finished even and smooth without using extra cement including necessary form work complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in cement mortar 1:4. all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and surface finished even and fair to receive wall tiles complete all as specified and directed.

M&L for light shade, vitrified ceramic tiles; 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

All as per item No 44 herein before but on vertical surfaces such as skirting etc. set and jointed in neat cement slurry and jointed in white or coloured ement to match the surfaces complete all as specified and directed.

M&L for Joint free, Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for Joint free, Non - skid Ceramic tiles 7 to 10 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

All as per item No 47 herein before but on vertical surfaces such as skirting etc. set and jointed in neat cement slurry and jointed in white or coloured ement to match the surfaces complete all as specified and directed.

M&L for Joint free; glazed ceramic tiles in vertical surface of size 450 mm X 350 mm X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

M&L for rendering 10 mm thick Cement Mortar 1:4 over brick or concrete wall surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in two layers [base layer 10mm in cement mortar 1:6 & finishing layer 5mm thick in cement mortar 1:4] using liquid water proofing compound in 2nd layer only on brick work or concrete surfaces of wall, surfaces finished even and smooth without using extra cement complete all as specified and directed. Note: (i) Water proofing compound shall be measured and paid separately as supply only (ii) The quantity of waterproofing compound used shall be as per manufacturer instruction and the proof for the same shall be submitted along with the bill for claiming payment.

M&L for rendering 15 mm thick Cement Mortar 1:4 over brick or concrete wall surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L for 3mm thick wall care putty on wall surfaces after preparation of wall surface complete all as specified and directed.

M&L for 3mm thick wall care putty on ceiling after preparation of wall surface complete all as specified and directed.

M&L for three coats of white wash on walls, pillasters, cornices, etc., on newly plastered walls including preparation of surfaces all as specified and directed.

M&L for two coats of cement base paint on walls, pilasters, cornices, etc., on newly plastered walls over a coat of chalk white primer including preparation of surfaces complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coats of distemper oil emulsion over a coat of chalk white primer complete all as specified and directed.

M&L for complete removal existing treatment of old decorative surface of walls and applying two coats of distemper oil emulsion over a coat of primer, including removing of unnecessary nails, making good holes, cracks, etc., with lime putty or Plaster of Paris to make the surface smooth wherever necessary complete all as specified and directed.

M&L for complete removal existing treatment of old decorative surfaces of walls and applying two coats of cement base paint over a coat white wash, including removing of unnecessary nails, making good holes, cracks, etc., with lime putty or Plaster of Paris to make the surface smooth wherever necessary complete all as specified and directed.

M&L for preparation of old decorative surface of ceilings and applying one coat of white wash including removing of unnecessary nails, making good holes, cracks, etc., with lime putty or Plaster of Paris to make the surface smooth wherever necessary complete all as specified and directed.

S&F in repair for 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc. 0.5 Sqm in each pane including hacking out old broken glass complete all as specified and directed.

M&L for one coat of synthetic enamel paint on old painted wooden surfaces of any description over 10cm width or girth including necessary preparation of surface complete all as specified and directed.

M&L for one coat of synthetic enamel paint on old painted steel surfaces of any description over 10cm width or girth including necessary preparation of surface complete all as specified and as directed.

M&L for two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description exceeding 10cm width or girth including necessary preparation of surfaces complete all as specified and directed

M & L for two coats of synthetic enamel paint over one coat of red oxide primer on new steel surfaces exc 10cm width or girth including preparation of surfaces complete all as specified and directed.

M&L for 10mm thick Plaster of Paris (POP) false ceiling of approved quality as per manufacturer instruction and making of frame for false ceiling with the help of GI/MS mould main and cross member of required size as per site requirement and tightened with the GI/MS angle iron at side of wall with angle iron fixed with fastener including supply and fixing GI wire mesh to retain false ceiling to the GI/MS frame screw as required cutting of holes and supply and fixing of surface even and smooth complete all as specified and as directed.

M&L for making of Plaster of Paris (POP) rounded/oval shape modeling at the corner of wall and ceiling (Cornice) of width not exceeding 30cm as per approved design recommended by Engg- in- charge and finishing the surface with two coat of distemper oil emulsion paint complete all as specified and directed.

M&L for making of Plaster of Paris (POP) rounded/ oval shape modeling at the center of wall/ ceiling as per approved design recommended by Engg- in- charge and finishing the surface with two coat of distemper oil emulsion paint complete all as specified and directed.

M&L for preparation of new surfaces of plaster of paris (POP) and applying two coats of distemper oil emulsion on ceiling over a coat of chalk white primer complete all as specified and directed.

Taking up or down steel tubing alongwith its connections from any position such as wall, floor etc., including cleaning for refixing complete all as specified and directed for the following size of pipes:-

15 mm Bore

20 mm Bore

Refixing of old steel tubing and connections in new or old position on walls, ceiling, floors etc all as specified and directed at site for following sizes :- Note:- Serviceable steel pipes taken under item-19.01 to 19.08 shall be used.

15 mm Bore

20 mm Bore

S&F steel water tubing ISI marked, medium grade galvanised, with all fittings such as bends, elbows tees, short, pieces, connections, back nuts, diminishing pieces caps, plugs and unions etc, fixed to walls, ceiling, floor etc., with clamp complete of the following sizes :-

15 mm Bore

20 mm Bore

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) having 100mm internal dia, set in cement mortar including disposal of rubbish out of the premises complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, floor etc., complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) bends any radius all as specified.

S&F in repairs rotational moulded polythylene water storage tanks (cylindrical vertical with closed top) of capacity 1000 ltrs hoisted and fixed in position all as specified in SSR Part I including dismantling and taking down the existing unserviceable tank complete all as specified and directed.

S&F in repairs rotational moulded polythylene water storage tanks (cylindrical vertical with closed top) of capacity 500 ltrs hoisted and fixed in position all as specified in SSR Part I including dismantling and taking down the existing unserviceable tank complete all as specified and directed.

S&F in repairs 15 mm bore; bib tap chromium plated, cast copper alloy screwed down high pressure with crutch or butter fly handle, screwed both end of pipe all as specified and directed.

S&F in repairs 15 mm bore fancy type, chromium plated bib tap cast copper alloy screwed down high pressure with crutch or butter fly handle, screwed both end of pipe all as specified and directed.

S&F in repairs 15 mm dia bore, fancy type, pillar taps, cast copper alloy, Chromium Plated, with capstan head, screwed down high pressure with or with out lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe or unions and fixed complete all as specified and directed.

S&F in repair 15mm bore brass chromium plated basin mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15mm bore brass chromium plated wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repair 15mm dia bore fancy type, chromium plated Angle Stop valves (Concealed type), cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair 15mm bore dia, Stop Valve, fancy type, chromium plated with long shank and cup (concealed type), cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified an directed.

S&F in repairs 20mm dia ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified & directed.

S&F in repairs grating doom 125 mm dia of with waste hole of PTMT (Minimum wt 40 gms) all as specified and directed.

S&F in repairs 15mm dia, PVC connection pipe of 450mm long with PTMT nuts complete all as specified and directed.

M&L for Cast iron floor trap, sand cast suitable for 75mm dia outlet, with brass chromium plated grating including jointing to waste pipe with run lead complete including taking out old trap all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and flushing pipe, antisyphonage pipe etc., complete all as specified and as directed.

S&F in repairs vitreous china squatting pan Orissa pattern of size 580mm X 440mm with integral foot rest and 'P' or 'S' trap including cement concrete bedding, connecting to flushing pipe and 'P' trap including taking out old WC with cement concrete bedding, making good and unserviceable connections and connecting etc. complete all as specified.

Supply & fixing in repair brass chromium plated toilet paper holder fixed to walls with chromium plated (CP) brass screws complete all as specified & directed.

S&F in repair 550x400mm size vitreous china wash basin, white, flat back, including brackets, cutting for and pinning in ends of brackets or erecting stand, inexclusive of fixing of supply and waste pipe complete all as specified and as directed

S&F in repairs for soap dish vitreous China of size approximate 160X160X90mm fixed to plugs with chromium placed brass screw all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as speciified and as directed.

S&F in repairs 10 ltr capacity of PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe all as specified and directed.

S&F in repair brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe of dia 15mm bore complete all as specified and directed.

S&F in repairs EWC plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as specified and directed.

S&F in repair Brass Towel Ring (Minimum 200gms), Chromium plated brass screws and wooden/plastic cleats all as specified.

S&F in repair Bathroom Mirror Cabinet of size 450x350 mm all as specified and directed.

S&F in repair Hand Shower (Health Faucet) Chromium plated with 1.5m long flexible Tube & wall Hook.

S&F in replacement stainless steel plate rack, 1.00mm of overall size 900mm x 1200mm x 250mm with brass screws complete all as specified and directed.

S&F 12mm dia, GI round bar, "S" shaped, suitable for inserting into the fan hook as required at site for hanging fan/ light fittings complete all as specified and directed.

E/M Portion Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surface of walls, floors, etc.. all as specified and directed.

Taking down ceiling fans of any size/sweep after disconnecting the wire from existing ceiling rose and refixing the same after cleaning dust, oiling, greasing including providing flexible cable from ceiling rose to connector of fan complete all as directed.

Material & labour for point wiring using approved colour coding as per IS with 1.5 sqmm two single core PVC insulated but unsheathed FR cable, 1100 volts grade, ISI-694 marked with multistranded copper conductor and earth continuity wire with similar 1.5 Sqmm cable (including connecting to earth dolly) drawn through ISI Marked heavy duty rigid PVC conduit concealed with all accessories etc with mild steel sunken box with earth dolly duly conceled in wall and having modular cover plate with frame suitable for modular switch/Sockets/regulators for the following :-

One light point controlled by 6 Amp switch one way.

One light point controlled by 6 Amp two 2 - way switches.

One 3 pin socket outlet, 5 Amps on the same board.

One 3 pin socket outlet, 5 Amps on independent board.

One bell/ buzzer point controlled by one push button.

All as per item No : 108 point wiring with 2.5 Sqmm single core copper cable and earth continuity wire with 2.5 Sqmm single core cable for one three pin 15 Amp socket outlet point on independent board.

Material & labour in repair for submain wiring with approved colour coding as per IS in replacement with 4 runs of 6 Sqmm size main cable and two run of 4 Sqmm size earth continuity conductor of single core PVC insulated but unsheathed FRLS cable of specified size multistranded copper conductor 1100 volts grade IS-694 marked drawn through Concealed heavy duty ISI marked rigid PVC Conduit of size 25mm dia with all fittings accessories including making good the surface on wall etc complete all as specified and directed. Note:- 4 run of 6 sq mm and two run of 4 sq mm and one run of heavy duty 25mm dia PVC Conduit will be measured as one unit.

Material & labour in repair for submain wiring with approved colour coding as per IS in replacement with 2 runs of 4 Sqmm size main cable and one run of 2.5 Sqmm size earth continuity conductor of single core PVC insulated but unsheathed FRLS cable of specified size multistranded copper conductor 1100 volts grade IS-694 marked drawn through heavy duty ISI marked rigid PVC Conduit of size 25mm dia concealed with all fittings accessories including making good the surface on wall etc complete all as specified and directed. Note:- 2 run of 4 sq mm and one run of 2.5 sq mm and one run of heavy duty 25mm dia PVC Conduit will be measured as one unit.

Supply & fixing modular switch 01 way 6 Amp, 01 module complete all as specified and directed.

Supply & fixing modular switch 02 way 6 Amp, 01 module complete all as specified and directed.

Supply & fixing modular switch 01 way 16 Amp, 01 module complete all as specified and directed.

Supply & fixing modular bell push 6 amp 230 volt 50 hz AC supply one way, complete all as specified and directed.

Supply & fixing modular socket 6 Amp, 2 module complete all as specified and directed.

Supply & fixing modular socket 6 / 16 Amp, 02 in 01, 02 module complete all as specified and directed.

Material & labour in replacement modular step fan regulator 2 module suitable for 230 Volt 50 Hz supply all as specified and directed.

Supply & fixing ceiling rose surface Bakelite 3 terminals 65X50mm , 230V including PVC Box of size 3"X3" round type.

Supply & fixing for Lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fitting completes all as specified and directed.

Supply & fixing highly efficient LED retrofit Lamp 12W used as a ready replacement for existing GLS/CFL all as specified and as directed.

Supply & fixing in repair for wall mounted LED 10W CRCA fitting 230 V with extruded aluminium heat sink provided for efficient heat dissipation and integeral electronic driver connector block etc complete with all accessories internally prewired including neccessary mounting arrangement , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including neccessary polycarbonate LED tube 2FT 10 W complete all as specified and directed.

Supply & fixing in repair for wall mounted LED 20W CRCA fitting 230 V with extruded aluminium heat sink provided for efficient heat dissipation and integeral electronic driver connector block etc complete with all accessories internally prewired including neccessary mounting arrangement , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including neccessary polycarbonate LED tube 4FT 20 W complete all as specified and directed.

S&F in repair for environment friendly high efficiency with better thermal management type building security light 25Watt with integral electronic driver connector block etc complete with all accessories internally prewired including necessary mounting arrangement, provision of 2 core 1 Sq.mm multistranded copper conductor from ceiling rose to fitting, replacement of old rusted GI bracket complete all as specified and directed.

S&F in repair for MCB DB TPN 4 way double door sheet metal enclosure comprising of OEM/manufacturer specified bus bar and neutral link, 415 Volts, 50 Hz including inserting in wall complete all as specified and directed

Supply & fixing in repair for MCB triple pole and neutral 415 Volts, 63 Amps, 10 KA.

Supply & fixing in repair MCB DB SPN 04 way double door sheet metal enclosure with OEM/manufacturer specified bus bar and neutral link complete to fixtures all as specified and directed.

Supply & fixing in repair MCB DB SPN 08 way double door sheet metal enclosure with OEM/manufacturer specified bus bar and neutral link complete to fixtures all as specified and directed.

Supply & fixing in repair 'C' curve MCB SPN 240 volt 32/40 Amps

Supply & fixing in repair 'C' curve MCB SP 240 volt 6 to 30 Amp

Supply & fixing in repair single pole and neutral sheet metal enclosure with a two pin earth plug and socket etc with one Double pole MCB 415 Volts 20 Amps complete.

Supply & fixing Exhaust fan, PVC body, size 250 mm, max 35 watts, minimum 1200 RPM, Single phase, 230 Volts including providing flexible copper cable from ceiling rose to connector of fan complete all as directed.

M&L for plate earthing for complete with galvanised mild steel plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (in earth pit not less than 2.25 m below normal ground level) with the top edge of the earth plate at a depth not less than 1.5 m below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and incl GI wire 4.0mm dia bolted (with GI nuts, bolts & check nuts) and riveted to earth plate at one end and connected to metallic bodies of equipments etc at the other end , earth strip encased in and including 40 mm bore GI light grade pipe with all fittings from top of electrode to body of equipment fixed with and including 25 x 3 mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe light grade from bottom of earth pit to top of electrode complete with wire mesh , funnel and earth pit in PCC 1:2:4 type B-0 using 12 mm graded crushed stone aggregate and RCC cover complete all specified and shown in electrical plate No -3 of SSR Pt-I. (Note :- GI wire 4.0 mm dia and 40 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.)

Supply and fixing water heater (Geyser) storage type of capacity 25 Ltrs, energy saver/energy-efficient Star rating, 230V, 2KW element, single phase AC supply, inner tank made out of heavy duty stainless steel sheet glass line coated, having pressure release valve, non return valve and drain valve, thermostat with auto cut off etc, hanging on wall with 4 Nos steel fastners 10mm dia 100mm long and making good the disturbed surface as per existing surfaces, including electric, earthing and water connection to geyser and testing on load (Filled with water) upto entire satisfaction of Engineer-in-Charge/JE complete all as specified and directed by Engineer-in-Charge. Note :- (i) Srl Number of geyser and 'GE AF Amla' shall also be writing on geyser with red colour permanent marker, which will be issued by Engineer-in-Charge and cost for the same shall deemed to be included in the quoted unit rate, nothing shall be paid extra on this account. (ii) Geyser installed/hanging at various locations as directed by Engineer-in-charge with in the Jurisdiction of GE AF Amla (from market to AGE E/M store/AGE E/M store to sites /Location, all conditions will be the responsibility of contractor and nothing extra will be admissible on this account (iii) Provision of one set of hot and cold water coupling pipe and one CP brass stop cock of 15mm bore at inlet are deemed to be included in the quoted rates.

Note:- (i) The amount against Schedule of Credit mentioned in tender document shall be deducted from the total amount quoted against Sch 'A' while deriving the Contarct Sum for Acceptance.

chronicle enterprises

Meet Road Lines

M/s Shree Ganesh Traders

Raj Construction