REPAIR AND MAINT OF FLOORING, JOINERY, PLASTERING AND CONNECTED B/R WORKS IN OTM ACCN AT MIL STN PATIALA.

Amount

Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified.

Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified.

Taking down Shutters of any description exc 1 sq. m and n exc 2 sq. m each

S&F Spray Docu painted Pressed steel frames made of MS sheet of 1.20 mm thickness for doors with single rebate including necessary fixing lugs, hinges, lock strike plate, hold fasts ,filling PCC (1:3:6 Co) in chowkhats , PCC 1:2:4 B1 hold fast blocks etc., complete as specified,size 105x 60mm including taking down old chowkhats or frames any type incl shutter exc 1.50 sqm but not exceeding 4.00 sqm including cutting holes and making good reqd to shape for hold fast blocks for new frame complete all as specified. ( Note :- Disturbed portion of existing floor /wall / tile / plaster etc duing fixing of chowkhats shall be repaired to match with existing finish .Cost of the same will be included in this item )

S&F Spray Docu painted Pressed steel frames made of MS sheet of 1.20 mm thickness for doors with double rebate including necessary fixing lugs, hinges, lock strike plate, hold fasts ,filling PCC (1:3:6 Co) in chowkhats , PCC 1:2:4 B1 hold fast blocks etc., complete as specified,size 125x 60mm including taking down old chowkhats or frames any type incl shutter exc 1.50 sqm but not exceeding 4.00 sqm including cutting holes and making good reqd to shape for hold fast blocks for new frame complete all as specified. ( Note :- Disturbed portion of existing floor /wall / tile / plaster etc duing fixing of chowkhats shall be repaired to match with existing finish .Cost of the same will be included in this item )

S&F factory made flush shutters 35mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides with veneer with 6mm thick lipping frame to match, complete all as specified and fixing of following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 4 nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x250/300 mm - 1 nos per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf (Note:- Steel Mongery shall be paid as supply only against respective item.)

S&F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-1 section 8 clause 8.20(a), kiln seasoned and chemically pressure treated and fixing of following items, complete all as specified and direceted. (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 4 nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x300mm - 1 nos per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf (Note:- Steel Mongery shall be paid as supply only against respective item.)

Supply only Stainless Steel (304 Grade) Finished Butt Hinges 150mm, complete all as specified.

Supply only Stainless Steel (304 Grade) Finished Tower Bolt 200mm long, complete all as specifed.

Supply only Stainless Steel (304 Grade) Finished Handles 200 mm, complete all as specifed.

Supply only Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x250/300 mm, complete all as specifed.

Supply only Stainless Steel (304 Grade) Finished Floor Door Stooper, complete all as specifed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature 1.40mm and fixed in repair with stainless steel wire stapples complete all as specified and directed.

S&F powder coated 50 microns extruded aluminium doors & shutters made out of section 63.5x38.10x1.29mm for chowkats or frame & shutters made of size 44.45x44.45x1.29mm for side rails and middle rail, 114.3X44.45X1.29mm for top rails and bottom rails and including 12mm thick PVC Celuka board wooden finish pre laminated on single side and plain on other side below middle/lock rail and 5mm thick frosted glass above middle/lock rail and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beads 20mm size with and complete all as specified and directed including fixing of following items: (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 3 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 200mm long - 2 nos per leaf (c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf (Note:- Steel / Aluminium Mongery shall be paid as supply only against respective item.)

Providing and fixing factory made extruded aluminium casement windows with 50 micron powder coating doubled panelled and double shutters consisting of frame and mullion of 101.60X44.45X1.29 mm and shutters made of 63.5X31.75X1.29mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperature in inner shutters complete fixed in all respect as specified including fixing of following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 2 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf. (c) Powder Coated Aluminium Handles 150 mm - 1 nos per leaf. (Note:- Steel / Aluminium Mongery shall be paid as supply only against respective item.)

Providing and fixing factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5X38.10X1.29 mm including 5mm thick frosted glass in lower 65% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 35% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and complete fixed in all respect as specified.

Supply only powder coated aluminium tower bolt 200 mm long, complete all as specifed.

Supply only powder coated aluminium tower bolt 150 mm long, complete all as specifed.

Supply only powder coated aluminium handle 150 mm long, complete all as specifed.

Hacking out old broken glass (any thickness size quality or description) from wooden or steel frame glazed with putty or fixed wih beads, complete all as specified and directed.

S&F of 3 mm thick plain glass, ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane, complete all as specified and directed.

S&F of 3 mm thick pin headed glass, ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane, complete all as specified and directed.

M&L for anti-skid premium quality coloured tiles 400 X 400 mm and 7-8 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 20 mm thick screed in cement mortar (1:4) over and pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L for ceramic glossy finish, joint free premium quality coloured tiles 600 X 300 mm and 6-8 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified. Note : Dado should be flushed with the wall plastering.

Demolition of cement concrete (un-reinforced) in any thickness (below or above ground level), complete all as specified and directed.

Taking down cement plaster on brick Walls built in cement mortar including raking out joints, hacking for key, scrubbing down with water etc

10mm thick cement plastering in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.

Rendering 15mm thickcement plaster in cement mortar 1:4 (mixed with integral liquid water proofing compound of approved make as per manufacturer's instructionsbut not less than 0.20 Ltr per bag of cement) on fair faces of brick work or concrete external surfaces finished even & smooth without using extra cement complete all as specified and directed. Note: - Integral liquid water proofing compound shall be measured and paid for separately against respective item.

Rendering 5mm thick cement plastering in cement mortar 1:3 as on ceiling, chhajjas & other concrete surfaces finished even and smooth without using extra cement.

GI wire netting 0.90mm dia and 12 mm mesh lathing to wood or metal studing, joists, etc. in walls, ceiling, stanchions, beams, etc., incl all laps, cutting & waste.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant cement priming paint complete all as specified and directed

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over 1mm th wall putty complete all as specified and directed

Preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash on ceilingcomplete all as specified and directed

Supply only water proofing liquid compound

S & F Anodised aluminium window and ventilator shutters fixed type without sash bar, powder coating of any colour ( thickness of powder not less than 50 microns). Aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws etc. complete all as specified

S & F Anodised aluminium powder coating of any colour( thickness of powder not less than 50 microns) window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.),hinges type B-21 100mm long (2no.) suitable handle ,(01 no.) complete all as specified.

S & F Factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S & F 100 mm size PVC butt hinges all as specified and directed.

S & F 125 mm PVC handles all as specified and directed .

S & F 200 mm long PVC tower bolt all as pecified and directed .

M & L for Built in cup boards with pressed steel frame of size 75x45x1.25mm thick and shutter of 1.00 mm thick MS sheet including spray painting 2 coats over a coat of red-oxide primer on steel shurfaces all around all shown on drawing No TD-178 sheet 2/3 to 3/3 dated 12 May 2001 (overall external size of cup board shutter incl frame shall be taken into consideration for the pupose of measurement) including One No hanging rod of CP steel 15/20mm bore with brackets & two Nos peg set of three pegs each fixed inside the shutter complete fixed in repairs i.e, icl taking down and removal of old unserviceable wooden or steel built-in-cupboards incl frame all as specified and directed by Engineer-incharge.

M & L for Machine cut Mirror polished Kota stone 20mm (+2mm) thick slab as in cooking platforms/ landings, treads and risers of stairs and steps laid over and including screed bed or 15mm th bedding layer in cement mortar 1:3 as base laid and jointed with grey cement slurry mixed with pigment to match the shade including rubbing, polishing complete all as specified and directed.

M & L for Machine cut Mirror polished Kota stone slab flooring 20mm thick laid over and including 20mm screed bed or bedding layer in cement mortar 1:4 as base laid and jointed with grey cement slurry mixed with pigment to match the shade including rubbing, polishing complete all as specified and directed.

Rounding to edges of stone slabs one edge , such as in steps, cooking plateforms & other similar situations complete all as specified and as directed.

M & L for Vitrified Ceramic tiles 10mm thick light colour (Square/ rectangular) polished, area of each tile 600 x 600 mm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over 15mm thick screed/ bedding layer in CM 1:4 complete all as specified and as directed.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets

Dismantling timber scantlings 40 sq. cm and over in section, in any position

Anodised aluminium snap grid frame work for false ceiling all as specified (Size of grid 605 x 605mm) incl Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

Material & labour for Gypsum Board 600mmx 600mm x 12mm thick in ceiling fixed as per manufacturers instructions all as specified and as directed by Engineer incharge.

S & F for Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing.

M & L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

Dismantling of Brick work including all quains and arches pillars etc built in cement mortar or cement lime mortar complete all as specified and directed.

M&L for brick work in cement mortar (1:4) using sub class 'B' old size bricks staight or curved on plan exc 6.0 m mean raidus complete all as specified and directed

M & L 50mm thick PCC (1:3:6) type C2 (using 40mm grade aggregate) as in plinth protection, finishing the surfaces even & smooth w/o using extra cement.

M & L Cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in sub base under floors etc complete all as specified and as directed.

S & F precast concrete rubber moulded interlocking paver block any shape and size of 60mm thickness, M-35 grade & incl 25mm thick layer of sand cushion complete all as specified and as directed. confirming to IS 15658-2006, complete all as specified and directed.

M/S RAJ KUMAR GUPTA

Arneja Builders

M/s Anil Kumar and co.

m/s panchmukhi builders

FAVOURITE ENGINEERS

Buttar Construction Co.

RUPINDER SINGH SODHI